Search Documents

By R. I. Jaffee, C. T. Sims, C. M. Craighead

The fabrication of rhenium metal by powder metallurgy techniques is discussed. The following physical and mechanical properties have been measured and are reported: lattice constants, melting point, electrical resistivity, thermal expansion, spectral emissivity, modulus of elasticity, tensile properties and ductility at room and elevated temperatures, work hardening, recrystallization, grain growth, and oxidation resistance. IT is only occasionally that a metal reaches present-day technology with as little known about its properties as element No. 75, rhenium. Relatively scarce to date, it has been studied only infrequently and used less. Previous work on rhenium has been carried out primarily by European scientists. However, realization that rhenium occurs in commercial quantities in the United States recently has focused attention on this metal. Rhenium is a very dense high melting hexagonal-close-packed metal. Like tungsten and molybdenum, its highest oxide is volatile. However, when protected by reducing or inert atmospheres, its strength at high temperatures is greater than that of tungsten. Rhenium work hardens more than any other known pure metal, but, on annealing, becomes quite soft and ductile. Its vapor pressure is approximately that of tantalum, but it does not enter into the so-called "water cycle" nearly as readily as does tungsten. (The water cycle is a deleterious phenomenon causing blackening of lamp bulbs and vacuum tubes with subsequent failure of the filaments.) These and other properties, some already known and some found as a result of the current researches, have indicated that rhenium has many potential uses, primarily of an electrical or electronic nature. Rhenium or its alloys soon may be found in service as electron-tube filaments, cathodic emitters, or as electrical contact materials. In addition, rhenium or its alloys have potential use in such devices as high temperature thermocouples, and high wear-resistant parts such as precision instrument points. Rhenium, in the form of potassium perrhenate, was made available for this study by the Kennecott Copper Corp. The potassium perrhenate was reduced to rhenium metal in two stages, accompanied by leaching to remove potassium in the form of hydroxide. This impure metal was then oxidized to rhenium heptoxide and dissolved in water. The solution was neutralized with ammonium hydroxide to produce highly purified ammonium perrhenate, a typical analysis of which is shown in Table I. The ammonium perrhenate was ground to —325 mesh in a rubber-lined ball mill with Burundum balls. This operation caused a certain amount of impurity pickup, as reflected in the rhenium analysis shown in Table I. The fine ammonium perrhenate was reduced to metal with hydrogen. Particle size of the powder ranged from 1 to 25 microns, as illustrated by Fig. 1.

Jan 1, 1956

By O. Cuscoleca

The Austrian plants at Donawitz and Linz were the first to blow steel with high purity oxygen. The paper shows how the process was developed and gives a survey of the results achieved to date. Compared with open hearth steel of equal quality, the obvious advantages of oxygen steel are the low investment and conversion costs. The nitrogen content of oxygen steel is not higher than that of good open hearth steel. Rimmed and killed steel products made by the oxygen process are superior to rimmed and killed steel products made by the best open hearth process. TWO new steel plants using the principle of making steel with high purity oxygen went into operation in Austria, one at Linz (Vereinigte oster-reichische Stahlwerke) in November 1952 and the other at Donawitz (dsterreichisch-Alpine Montan-gesellschaft) in May 1953. An estimated 330,000 metric tons were produced by the two plants in 1953, the first year of operation. In 1954 production by Austrian plants- using the high purity oxygen approach will be raised to 450,000 metric tons. This will be in addition to facilities in Huckingen (Man-nesmann A. G., Düsseldorf, Germany), those planned and under construction at Hamilton, Ontario, Canada (Dominion Foundries and Steel, Ltd.), and elsewhere. It is expected that by 1955 a total capacity of one million tons of high purity oxygen steel will be available. At the close of the last century, because of increasing availability of scrap, open hearth steel production forged ahead at an ever increasing pace. This caused world steel production to rise faster than pig iron production and finally to overtake it. In 1911 65 million tons of steel were produced against 64 million tons of pig iron. World steel production was 209 million tons in 1951, while pig iron output was only 147 million tons. The 1951 breakdown for steel shows 118 million tons made from pig iron, while the balance, 91 million tons or 44 pct of the total tonnage of steel produced, was made from scrap. This increase in crude steel production on a basis of high scrap consumption led to the world market scrap shortage and soaring scrap prices. In the United States and other nations, production of converter steel has fallen far behind that of open hearth steel. The surplus of processing scrap, un-absorbable by converting mills and thus a welcome source for open hearth and electric melting shops in the past, together with regular scrap purchases, no longer can meet requirements of both open hearth and electric steel production in Europe. In addition, recent modification of the basic bessemer process, blowing with oxygenated blast, substantially raised the scrap capacity of these plants. Any further expansion of world steel production will necessitate utilization of self-containing processes in regard to scrap because of the shortage.

Jan 1, 1955

By P. Chaudhari, Michael B. Bever

The heat of solution at infinite dilution of selenium in bismuth, the heat of mixing of selenium and bismuth, and the limit of solubility of selenium in bis~rzuth have been determined at 573, 623; and 663°K by metal solution calorimetry. The heat of forrrzation of the compound Bi2Se at these temperatures has been determined from the heat effects associated with the precipitation of the compound from a saturated solution oj selenium and bismuth. The published information on the thermodynamic properties of the system Bi-Se is limited. The heat of solution at infinite dilution of selenium in bismuth at 623°K has been measured.' The heat of formation at 273 K1 and room temperature2 and the heat capacity at 80 K3 of the compound Bi2Se3 have been reported. An estimate of the heat of formation of the compound BiSe at room temperature has been published.2 Information on the phase relations in the system Bi-Se is available.' In the investigation reported here the following quantities have been determined at 573", 623", and 663°K: 1) the heat of solution at infinite dilution of selenium in bismuth, 2) the heat of mixing of selenium and bismuth in bismuth-rich solutions, 3) the limit of solubility of selenium in bismuth, and 4) the heat of formation of the compound BizSe. These quantities were determined by the addition of selenium to bismuth-rich solutions in a metal solution calorimeter. The determination of the heat of formation at the tem- perature of the calorimeter bath involved the precipitation of the compound from a saturated solution in the calorimeter. 5,6 This method differs from that commonly used which requires the addition of the compound and of a mechanical mixture of its components and yields the heat of formation at the temperature from which the additions are made (273 K EXPERIMENTAL PROCEDURE AND CALCULATIONS The solution calorimeter has been described in detail.' Pure bismuth (99.999+ pct) was used as the bath at the start of a run. The calorimeter was calibrated with small amounts of bismuth added from 273°K; the differences of the heat contents of bismuth at 273°K and the temperatures of the baths are listed in Table I. After the calibration, additions of hexagonal selenium (99.999+ pct) were made. Loss of selenium by evaporation was negligible. No unusual experimental difficulties were encountered.9 The differences in the heat contents10 of selenium at 273°K and the temperature of the bath, listed in Table I, were subtracted from the measured heat effects to give the "adjusted heat effects". The methods by which the heat of solution at infinite dilution, the

Jan 1, 1968

By George Sachs

I deeply appreciate the honor of being selected to deliver the twentieth Annual Lecture of the Institute of Metals Division. The subject of my paper is extremely involved and voluminous, therefore I shall discuss only some more recent experimental material and speculate somewhat on the physical and mechanical fundamentals of these changes. The flow and the rupture of a solid material are rather different phenomena. It is therefore surprising that up to a rather advanced stage in metallurgical science these two fundamental phenomena have been simultaneously treated and forced into the general conception of the "failure" of solid material. Only in this century, and particularly during the last 20 years, have the very different physical meanings of flow and rupture been clearly recognized. Several hundred of the more recent publications deal with these subjects.1 LAW OF SIMILARITY The basic values commonly considered responsible for the mechanical behavior of any material are the stresses. From this standpoint both a large and a small article made from the same homogeneous metal and of geometrically similar shapes should behave identically, i.e., they should deform geometrically in a similar manner, if subjected to the same stress values at corresponding points. This "law of similarity" was introduced about 60 years ago simultaneously by Barba2 and Kick3 and was derived from the classical theory of elasticity. As far as the plastic behavior of a metal is concerned, this rule appears to be valid. The conventional properties of large and small tension or compression test bars, machined from larger sections, are identical; while the force required to deform a section is proportional to its cross-sectional area and the work consumed in deforming geometrically similar articles in a geometrically similar manner is proportional to its volume. The general trend of the stress-strain diagram of a metal is independent of the section size (Fig. I). No exceptions from this rule are known. However, if the deformation of a metal is continued until rupture occurs, and the breaking stress or the work consumed is measured, a test bar of large cross section appears to fail before or at lower stresses than does one having a small cross section. Thus, the specific impact energy has been often found to decrease with increasing size of the test specimen, particularly for materials with a limited ductility.4 Another exception from the rule of similarity is offered by fatigue-strength values, which usually decrease with increasing section size. 5,6 The conclusion must be drawn from these experimental facts that the ductility of a homogeneous metal decreases with increas¬ing section size (Fig. x). This effect has been actually confirmed by Docherty,7 who observed that in static notch bending tests large specimens failed earlier and in a more brittle fashion than small specimens ma-

Jan 1, 1941

By F. E. Harris

IT has been said that carbon is "ubiquitous" with reference to iron alloys. Certainly at temperatures where carbon and iron form the solid solution, austenite, it may be readily added to, or removed from, steel surfaces. Differences in concentration potential are the sole requirements for carbon flow. To measure the rate of carbon flow, a proportionality factor, D, is arbitrarily expressed in units of (length)2 X (time)-1. If the term used for carbon concentration is weight pct C, as is customary, then a factor must be found, changing this term to one of weight per unit volume when the diffusion coefficient, D, is used in flow formulae. The determination of D values for carbon is complicated since D varies with the concentration itself. The Matano method has often been employed for systems involving a variant D. This method expreses an evaluation of unsteady flow whereby .0 is given a relationship with the numerical value of C-X slopes. The author contends that this solution is incorrect, except when D is invariant. The primary purpose of this paper is to support this contention. Here diffusion is controlled under two conditions of flow. The first part deals with the steady state; the second part considers unsteady flow under definite restrictions. Beginning with the fundamental concept, the development is continued until equations for C-X curves are obtained. The solution is then subjected to experimental data. It is realized that a great amount of reliable data is required for a rigorous proof. No such research is claimed. Instead an attempt is made to set forth the physical significance of the diffusion mechanism, and particularly to express the factors which influence the flow of carbon in austenite. Of equal significance is the implication that gaseous media may be employed with reasonable accuracy in making these determinations. THE STEADY STATE DIFFUSION OF CARBON IN AUSTENITE The fundamental experiment defining diffusion in solid metals may be readily performed for carbon in gamma iron.1 For this experiment a thin plate of medium carbon steel is chosen. The surfaces of this plate may be taken as two parallel planes which may be considered infinite for points well in the center of the planes. These two planes are held at different concentrations of carbon at a constant temperature. This temperature, 1700°F for example, is one where the single phase, carbon in solution with gamma iron, exists. When these conditions are held for a sufficient time the concentration of carbon of the different points of the solid settles down towards its steady state value. At points well removed from the ends, the concentration will remain the same along planes parallel to the surfaces of the plate.

Jan 1, 1947

By M. N. Dunlap

This article summarizes the successful incorporation of a flash-flooding stream into the tailing-disposal system at the St. Joseph Lead Company's Federal Division mill, in St. Francois County, Missouri. The mill was built in 1906, by the Federal Lead Co., as its No. 3 mill for the concentration of southeastern Missouri lead ores, and damming Davis Creek was first considered in 1908. Plans were made also in 1925 and in 1937. Dam layouts varied from a reinforced concrete structure to a barrier built of tailings alone. .All were abandoned because of liability that would be incurred by flash-flood rupturing of an incompleted dam. By 1942 mill capacity had reached 12,000 tons daily and increasing tailing-disposal costs again focused attention on the Davis Creek basin. This time the problem of riskless dam building was solved. Moreover, most of the items that appeared in the answer were materials that normally required wasting and the major portion of labor involved performed functions that it mould normally have done, without constructive benefit, elsewhere. The new layout also made possible advantageous changes in mill-water supply pumping; static head being reduced from 514 ft to 9; ft, friction head from 4900 ft to 2860 ft, and pumping can be done now at periods of low power demand. The following facts about the Davis Creek watershed explain the 36-year reluctance to reach these, and other, benefits. Size: 3600 acres. Outline: roughly pear-shaped, 21/2 by 3 miles at the largest dimensions. Topography: mostly hill land with steep valleys. Relief: 760 minimum to 1153 maximum. Maximum rainfall: 3.36 in. per hour. Permanent water: none natural. Now 2200 gpm discharged through 16-in. drill hole from mine pumps underground. Geology: the 17 acres near dam centerline is Bonne Terre dolomite covered with sand and gravel eroded from Pleistocene beds that cap some of the hills. The remainder of the pond basin is on Davis shale. Soil cover: mostly second-growth timber with some abandoned fields; all subject to careless burning, which reduces water-retaining ability. Flood history: flash-flooding that had taken at least one life. Downstream values: two railroad bridges before creek intersection with Flat River. Immediately below confluence, a highway bridge, a low-water crossing, a few business establishments and several blocks of residences. In July 1942 the following segments of an ingenious plan were put into operation. A ditch 270 ft long, 16 ft wide and 51/2 ft deep was excavated to bedrock in the gravelly soil along the proposed dam's centerline. This excavation, which exposed many gravel-filled channels, was run full of slimes drawn from a riser set in the top of an adjacent tailings-disposal

Jan 1, 1949

(The paper by L. H. De Wald-Tech. Pub. No. 429 was presented at the Boston meeting, September, 1931.) W. A. SCHEUCH, Chicago, Ill.-Since starting up our Hawthorne copper wire plant we have found that wire bars from certain suppliers perform quite differently from those of other suppliers. In attempting to evaluate these bars, we made cross-sections, and in making these cross-sections we found considerable variation in the crystal structure. Indications were that there was some preference in the type of crystal structure. In attempting to find the reason for that we discussed it with the various producers and-also reviewed the literature. Mr. DeWald was assigned to determine the various factors that enter into copper wire bar crystal structure, on the basis that the product was a horizontally cast wire bar of practically identical composition and of recognized good composition for the present quality product sold in the market. Mr. DeWald has asked me to say that he should have made reference to Mr. Dalzell's paper on a theory concerning gases in refined copper. D. K. CRAMPTON, Marion, Conn. (written discussion).-Mr. DeWald has set forth an interesting and thorough exposition of the factors controlling macrostructure of this material. It is particularly interesting to us as it somewhat parallels work we have done on macrostructure of round copper billets for piercing into tubes. Our findings as to the effect of the several variables on macrostructure check Mr. DeWald's. The general principles underlying the two are precisely the same. The fact that we worked with copper deoxidized with phosphorous instead of tough-pitch copper, and round billets cast on end instead of wire bars, does not influence the results. We have found that round billets cast so as to produce large radial grains have greater soundness and density than those with a fine macrostructure. Further, and more important, we have found that the billets with large radial grains show markedly different performance on piercing from those having a fine equiaxed structure. With a given temperature of billet and adjustment of piercing machine, the coarse-grained material requires appreciably lower power for piercing and goes through the operation inn appreciably less time. These two differences are of sufficient commercial importance to warrant exercise of great care in maintaining the coarse structure. It seems probable that much the same phenomenon should hold in the hot rolling of tough-pitch wire bars. We would expect that, other things being equal, the coarse-grained wire bars would roll more readily and require less power than fine-grained ones. Moreover, we believe the differences in initial structure of the wire bars should be largely eliminated in the hot rolling process and during the subsequent drawing and annealing, of wire would be entirely eradicated.

Jan 1, 1932

By W. H. Brandt

ThEre has been much progress in the last two decades in understanding the hardenability of steel. Roughly, the progress has been along two lines, which may be designated as empirical and fundamental. This empirical work has progressed to the point where steels may be manufactured to the desired characteristics quite closely and heat-treatment and application problems can be approached with considerable confidcnce. Particularly noteworthy among the empirical work is that of Grossmann,12. who has given formulas for calculating hardenability as a function of composition, and the establishment of the isothermal transformation curve by Davenport and Bain.13 The latter does not fall entirely in the class of an empirical study, for while it provides a means of presenting a tremendous amount of empirical data in the form of a single curve, it also outlines clearly the problems that face the fundamental investigator. The isothermal transformation curve shows clearly that the phenomena occurring in the neighborhood of the knee of the curve are those that limit the hardenability of steel. Above the knee of the curve, the product of decomposition of austenite is lamellar pearlite and fundamental progress has consisted chiefly of a detailed study of structure and formation of pearlite, largely at the hands of Mehl and his collaborators.'-5 They have shown that formation of pearlite proceeds by a process of nuclea-tion and growth and they measured both the nucleation and growth rate. However, there is still a wide gap between our empirical knowledge and fundamental knowledge, owing largely to the fact that there is no satisfactory theory of nucleation rate or of growth rate. This paper is being written in an attempt to Hl in a small part of the gap. A method was prcsented recently1' for calculating the velocity of edgewise growth of pearlite using an expression for the carbon concentration that satisfies the diffusion equation. The edgewise velocity of pearlite growth in a plain carbon eu-tectoid steel was calculated, using linear extrapolations of the ferrite and comentite solubilities. While the results are in fairly good agreement with the experimental facts, the calculated velocity of edgewise growth is smaller at 600°C. than G, the radial growth velocity of pearlite nodules, whereas one would expect it to be larger. In this paper the calculation will be repeated using a new extrapolation for the ferrite solubility, which gives better agreement between G and T', the calculated velocity of edgewise growth. A calculation will also be made of the effect of carbon content on velocity of edgewise growth, and the problems of calculating the effects of other alloying elements on growth rates will be discussed. It will be assumed that the mechanism of pearlite growth, established by Mehl and

Jan 1, 1947

By F. L. Robertson, C. H. Bacon, J. W. Till

A description is given of the development of a process for making low sulphur steel on furnaces fired with 2 1/2 pet sulphur oil. Slag and metal are analyzed at melt. Slag weight is estimated. A simple method for calculating necessary lime additions for making 0.025 and 0.035 pct sulphur steel is given. DURING the last 15 years John Summers & Sons have been confronted increasingly by the problem of producing a low sulphur steel from high sulphur materials. The principles adopted, the processes used, the data collected on a furnace specially set aside to study this problem, and speculation on future developments are dealt with in this paper. This study is limited to two melting shops which make sheet steel only, of the following analysis: C, 0.06 pct; Mn, 0.33; S, 0.04, 0.035, 0.03, and 0.025; and P, 0.02 and 0.015. All the processes described have reference to the manufacturing of this steel and are not necessarily applicable, without modification, to other steels. The raw materials used are given in Table I. Development of Process About 1934, Schenck's work on phosphorus was applied to frame quantitative rules for the removal of phosphorus, with great success. We could however, neither in our own work nor in the voluminous literature, find any assistance to frame quantitative furnace rules to remove sulphur. Perhaps, we should have persevered with Schenck's outstanding chapter on sulphur in The Physical Chemistry of Steelmaking, but we missed the importance of one (Ss) sentence on p. 478. "Evidently this ratio -------- is [S] the important quantity to be considered from the point of view of chemical reaction; it is clear that the sulphur content of the steel alone, as frequently given in the literature cannot suffice for judging the success of the reaction unless special details are given regarding the sulphur charge and the amount of slag."' We were not however very successful in getting values for Schenck's "n" that agreed with (S) arrived at by our direct analysis. [S] In addition to Schenck's work much attention was given to V value. The formula selected for V was: (SCaO) — 1.57 (2 P2O5) (S SiO2) After plotting many charges a curve was obtained, based upon the relationship between the percentage sulphur in the finished steel and V value, Fig. 1. For a long time this was used as standard with about a 60 to 70 pct success on producer-gas fired furnaces, if all uprising scrap was used and no bought scrap used. An inspection of this curve shows clearly that it is not a quantitative manufacturing process, and that it was not sure enough to go to the trouble and expense of doing stage analysis for P,O,,

Jan 1, 1952

This paper "On Coal" was published in three issues of The Western Gleaner in 1814. Name of author is not given. This magazine was started by Cramer, Spear & Eichbaum, in Pittsburgh, Pa., in December 1813, and ran for about two years. Copies are very rare, and this one is made from an original in the Darlington Library, University of Pittsburgh. This is almost certainly the first general article on coal published west of the Allegheny Mountains, and one of the earliest in this country. ON COAL Its Natural History-Mining of Coal-Phenomena occasioned by Fire-damp-Method of Coking-Distillation of Tar from Pit-coal-Gas-light-Coal, a Manure I. NATURAL HISTORY OF COAL There are few productions of nature which present to the philosopher a wider field of investigation than pit-coal. A substance highly inflammable is found in the deep recesses of the earth, sometimes loaded with numerous superincumbent strata of hard rock, and extending frequently along with these strata through a vast expanse of territory. Though metals may be said to be inflammable substances, as they combine more or less rapidly with oxygen when placed under particular circumstances, yet the character of rapid combustion with disengagement of light and heat, seems to belong. principally to such substances as are derived either from the animal or vegetable kingdom. That this is probably the case with regard to coal we are further induced to believe, by the remarkable circumstance, that the chemical analysis of this natural production yields especially, though in various proportions, those materials which constitute essentially the vegetable. And if any thing was wanting to confirm, us in that opinion we might trace in a number of fossile substances the gradual transition of the vegetable into the state of mineral coal. This fact is so intimately connected with the natural history of coal, that we cannot think it superfluous to give it some farther development. Among the great number of principles which the chemist is capable of tracing in the vegetable kingdom, the presence of extract, resin and fibre seem to form the characteristical marks of plants.-If vegetable matter be boiled in water, and the water, after having been strained and filtered, be exposed for some time to the open air, a flocculent precipitate takes `place from every part of the liquor; which soon subsides to the bottom of the vessel containing it. This is the extract; altered, indeed, by exposure, and now no longer soluble in water, a change which is supposed to depend on the absorption of oxygen; and if, by any means the proportion of oxygen be increased, the extract gradually becomes of a darker color, blackens, and approaches to the state of charred wood.

Jan 1, 1942

By Richard P. Schoemaker

Introduction In underground mining operations the effects of economic and mechanical factors on costs and profits can readily be appreciated and can perhaps be expressed in exact figures and percentages. Less apparent, but frequently more important, is the influence of physical stress. Stress causes failure of supports, collapse of openings, rockbursts, and other damage which directly affects the costs of maintenance, and also to a certain extent the accident rate. Stress can, however, if properly directed, be an aid to mining operations. The caving methods in metal mining and the long-wall method in coal mining are well-known examples. In large-scale mining operations it is almost impossible to neglect stress-control. A better understanding of the mechanism of rock pressure and the application of its principles to practical mining will inevitably lead to a reduction in operating costs. Many theories have been advanced to give the mining engineer a practical outline for stress-control but, although today most experts agree upon the principles of stress distribution around underground openings, there is still no generally accepted theory that explains all phenomena. The main reasons for this incomplete understanding of the problem are the lack of accurate knowledge of the physical properties of rocks under field conditions, and the great complexity of these conditions due to in-homogeneity of the rock, stratification, tectonic disturbances, and many other unknown factors. The research on the rock pressure problems has, however, yielded some valuable facts which, expressed in practical terms, and adapted to local conditions, may become a valuable aid for mining operations. The purpose of this paper is to give a review of the most important accomplishments of this research with respect to the stress phenomena around small underground openings, such as tunnels and shafts, so as to arrive at an outline of the problem as it stands today. Special emphasis is placed on a new theory by the German mining engineer, Rudolf Fenner, which has never before been published or discussed in English. The Pressure Dome Theory The formation of a dome-shaped space around underground openings is well known from field observations. When openings are made in rock under stress, the rock in the top of the openings will often fail, and caving will continue until the openings have assumed a dome-shaped form, after which equilibrium apparently is re-established. The oldest theory which attempted to explain the phenomenon is the "beam" theory, which postulates that the hanging wall consists of stratified measures that behave as independent beams with fixed ends and a uniformly distributed load. When failure of the beam occurs, inward shearing at the ends will cause the formation of a dome-shaped space. The pressure dome theory, which more or less evolved from the beam theory, merely

Jan 1, 1949

By J. W. Hickman

INTRODUCTION MOST of the electron diffraction studies of oxide films which form on metals and alloys have been carried out by oxidizing the specimens in an auxiliary furnace, cooling down to room temperature and then inserting the sample in the camera and taking a diffraction photograph. Prior to the investigations at the Westinghouse Research Laboratories, no systematic study of the oxidation of any metal or alloy had been made over a wide temperature range with photographs taken at elevated temperatures except the investigation of iron by Jackson and Quarrell.1 In order to interpret the electron diffraction patterns of the oxides which may form on alloys, it seemed advisable to make a comprehensive study of the oxidation of the purest metals available in the bulk form. Thus far studies have been completed on iron,2 cobalt,2 nickel,2 chromium ,2 Copper2, tungsten,3 molybdenum,3 beryllium ,4 uranium,4 thorium4 titanium5 and zirconium5 while investigations are in progress on tantalum and columbium, The next step in the study is concerned with the investigation of the oxides which form on binary alloys. Some of the alloys consist of a single, phase while others contain more than one phase. The identification of the oxides on the surface of a binary alloy may be more difficult than on the metals since oxides containing both metals as well as those of each metal separately may form. Furthermore, it is possible that solid solutions of the various oxides may occur. In these cases the electron diffraction method may not be able to identify the oxidation products unequivocally, Examples of solid solutions which may present difficulties are MoO2 and W02, Fe3O4 and FeO-Cr2O3 since the diffraction patterns are so similar. Since electron diffraction can determine only the structure of the oxide, the chemical composition must be inferred from the diffraction data based upon X ray diffraction investigations of specimens of known composition. It is possible in some cases to decide whether a given solid phase reaction can occur on the surface of an alloy by a study of available thermodynamic data. Table I lists the equations for the formation of most of the oxides from the elements together with values of log10 KR for the several temperatures. [OF°R = -RT In KR 0 and-~75T = logi°KR] [?F°R] and KR are the free energy and equilibrium constant of the reaction. Calculations may be made using the values given in Table I to determine whether a given solid phase reaction is possible thermodynamically. For example, a solid phase reaction should occur between aluminum and chromium' oxide to form

Jan 1, 1948

By Walter Crafts, C. M. Offenhauer

IN the course of study of the heat-treatment of low-alloy steels, the behavior of alloy carbides at subcritical temperatures was found to vary from that indicated by published investigations. In order to establish the ranges of formation of carbides in low-chromium steels, a series of steels containing up to 0.60 per cent carbon and 7.5 per cent chromium has been investigated with respect to the type of carbide formed after quenching and tempering at subcritical temperatures. The types of carbide formed as products of austenite transformation to pearlitic and pseudomartensitic structures have also been determined. There have been numerous investigations of the carbides in chromium steels and diagrams of the iron-chromium-carbon system.1 Westgren, Phragmén and Negresco2 identified the following carbides in chromium steels: [Cementite Fe3C (containing up to about 15 per cent Cr) Trigonal carbide Cr7C3 (containing up to about 55 per cent Fe) Cubic carbide Cr4C (or Cr23C3) (containing up to about 25 per cent Fe) Orthorhombic carbide . Cr3C2 (containing only a few per cent Fe)] The most complete information on the iron-chromium-carbon system was supplied by Tofaute, Sponheuer and Bennek3 and by Tofaute, Küttner and Büttinghaus.4 By means of dilatometric and microscopic studies, sections of the diagram were established. This diagram showed the presence of the special carbide Cr7Ca in steels containing about 2.5 per cent to 12 per cent chromium in low-carbon steels and from about 5 to 20 per cent chromium in r per cent carbon alloys from A1 to room temperature. The present investigation has shown that a carbide inversion from Fe3C to Cr7Ca occurs in chromium steels containing more than about 1 per cent chromium after hardening and tempering at subcritical temperatures above about 500°C. The type of carbide observed to be more stable in quenched and tempered specimens was also found to be produced by direct austenite transformation in corresponding ranges of temperature and composition. EXPERIMENTAL PROCEDURE The steels used in these experiments were made in magnesia-lined crucibles in high-frequency furnaces and were poured into 2-in. ingots. The ingots were forged into 1-in. round bars, and all heat-treatments were conducted on specimens of this section .size. Sections of the bar stock 8 in. long were hardened in air, oil or water depending on the composition, after heating to a temperature sufficiently high to dissolve the carbides. The low-carbon and low-chromium steels were not entirely martensitic after quenching, and contained some ferrite and pseudomartensite. No pearlite was observed in the microstructures after auenchine. The quenched bars were cut into

Jan 1, 1942

By Raymond B. Ladoo

Abrasives include the substances, natural or artificial, that are used to grind, polish, abrade, scour, clean or otherwise remove solid material, usually by rubbing action but also by impact (sandblasting, for example). They do not include abrasive tools-for instance, lathe tools and files-or polishing agents such as waxes, which act by filling pores. Detergents and cleaners whose action is chemical rather than physical are omitted although some chemical-action polishes and cleaners may also contain solid abrasives; for example, many automobile and metal polishes. General Considerations The most important physical properties of materials that qualify them for use as abrasives are hardness, toughness (or brittleness), grain shape and size, character of fracture or cleavage, purity or uniformity. For making bonded grain abrasives such as grinding wheels, additional important factors are stability under high heat and bonding characteristics of grain surfaces. The economic factors of cost and availability are always important. No one single property is paramount for any use. For some uses extreme hardness and toughness are needed, as in diamonds for drill bits; for others, the factors of greatest importance are hardness and ability to break down slowly under use, to develop fresh cutting edges when grains become worn-for example, in garnet for sandpaper, neither highly cleavable or friable grains nor extremely tough grains are wanted. For still other uses, great hardness is objectionable; for example, abrasives for dentifrices and for glass-cleaning soaps. For the most efficient use in the more critical applications, the different types of abrasives are rarely completely interchangeable; thus, while crushed quartz and garnet are both used in sandpaper, the papers are not at all interchangeable in their use applications. In the last analysis, the choice of a high-grade abrasive depends upon the quality and quantity of work done by the abrasive per unit of cost. Initial cost of an artificial abrasive. may be much greater than that of a natural abrasive but the artificial abrasive may do so much better work than the natural one, and do it so much faster, that the ultimate cost will be less. It is on this basis that artificial abrasives have largely replaced natural abrasives for grinding metal. Classification Abrasives may be divided into two general classes, natural and manufactured. The former includes all rocks and minerals used for abrasive purposes without chemical or physical change other than crushing, shaping or bonding into suitable forms. Manufactured or artificial abrasives are made either by heat or chemical action from metals or mineral raw materials. On page 2 is a list of the most important abrasives, classified as to inherent types and as to forms in which they are used industrially. For most types of use there are manufactured products that can be substituted for the natural products, usually at higher initial

Jan 1, 1960

By Benjamin Lustman, Robert F. Mehl

The study of the high-temperature oxidation of pure metals, intensively pursued experimentally since the pioneer work of Pilling and Bedworth1 and supplemented by the recent theoretical work of Wagner2 is now well advanced. The important field of low-temperature oxidation—i.e., oxidation extending only through the temper color range of thicknesses with the formation of thin oxide layers in the range from 0 to 1000-2000 ?ngstroms—has not, however, reached so satisfactory a state, owing largely to the experimental difficulties that attend the formation and study of thin films; most of the work has been performed on abraded specimens whose surface irregularities approximated the thickness of the films formed. It has been pointed out that the rates of oxidation of different crystal faces are different and that the difierence may be related to the orientation relationships that obtain between the metal crystal and the superimposed oxide crystal; it has also been suggested that this orientation dependence should manifest itself in rates of oxidation and perhaps also of corrosion in aggregates bearing preferred orientations.3'4 An attempt to measure the rates of oxidation of different crystal faces of alpha iron demonstrated this difference in rate,4 but the dependence of rate on orientation was not simple; the method of measuring thickness, consisting of a color comparison with barium stearate multi-films of known thickness, was not wholly satisfactory. For these reasons it was felt that a study of the rate of oxidation of single crystals prepared with surfaces as smooth as possible, using a sensitive method giving true film thickness, should be profitable. Copper was chosen because of the ease of reduction of the primary oxide film and because the orientation relationships between metal and oxide and the composition of the oxide films formed at low temperatures are known; for thin films formed at low temperatures, Cu2O alone occurs.22-24 Experimental Procedure Various methods of surface preparation were attempted in order to obtain a surface that would oxidize uniformly and repro-ducibly. Electrolytic polishing by the method of Jacquet5 and electrolytic and mechanical polishing followed by annealing in vacuum and in purified hydrogen at various temperatures were tested. The procedure finally adopted consisted in a fine metallographic polish followed by an anneal in purified hydrogen at temperatures of 900° to 1000°C. for 12 hr. or more. The surface so produced was very bright and smooth, with no trace of specular etching (though some grain-boundary etching was observed); indeed, fine scratches produced by the final polish were entirely removed by the high-temperature anneal. After this treatment, the specimens were cooled in hydrogen to room temperature and placed in the oxidation furnace, where

Jan 1, 1941

By G. R. Gardner, D. H. Davis

Increasing realization of the importance of dust control, and the recommendations of various agencies, have led the mining industry to become actively concerned with this problem. The background and necessity for adequate dust-suppression measures have been discussed in a number of publications, including those of the U. S. Bureau of Mines, and the use of spray water to reduce dust at the face and on roadways has been recommended. The problem resolves itself into obtaining adequate dust reduction at a reasonable cost. Inasmuch as the term "adequate dust suppression" has never been clearly defined, nor have permissible limits of dustiness (in terms of dust count) been established, it is apparent that any method selected may be required to meet additional demands. Until the industry has been given some indication of permissible limits of dustiness, no permanent solution is possible. Progress will be somewhat handicapped until such information is available. In addition, dust reduction must be obtained without the addition of any excessive moisture to the coal, since consideration must often be given to: I. Quality standards, particularly reduction in heat value. 2. Handling characteristics, particularly in regard to unloading from railroad cars and bins. 3. Application of dry methods of coal cleaning. 4. Necessity for fine screening within specified limits of oversize and undersize. Little detailed information is available as to the advantages and disadvantages of the several methods of water distribution, the location and protection of sprays, operating data on pressure, quantity of water, and so forth, and results obtained. In 1940 an investigation was undertaken to determine and evaluate the principal factors involved. This paper constitutes a progress report on this work and cannot in any way be regarded as complete on any one of the several phases. Classification of Dust Sources The various sources of underground dust may be classified as primary or secondary. A primary source is one associated with appreciable degradation of size, that is, where the greater part of the actual fines capable of becoming air-borne dust are produced. A secondary source may be considered as one in which the greater part of the fines have been produced at some previous operation and are in such condition that they can be dispersed as air-borne dust. These conceptions appear to be of practical significance, as experience indicates that when dust is controlled at the primary sources the importance of secondary sources is minimized. For these reasons, investigations to date have been concerned principally with the primary sources of dust, and this paper is concerned particularly with one of these—namely, undercutting. In accord with the foregoing definitions, the sources to which the following opera-

Jan 1, 1942

By L. C. Aycock, J. Hunter, P. M. Lyons

In view of the unfavorable discovery trend that has set in during the past few years, it seems permissible to infer that the large, more easily found crude reserves in Louisiana are now known. Without doubt, many new producing areas will be located, but in the light of development during the past few years the majority of new areas probably will be found at greater depths and from relatively poorer sands. f Although sufficient reserves exist in Louisiana to last at the present rate of production for a considerable period, additional reserves must be found in more intensive development of the presently known structures. In order to ensure the greatest ultimate recovery from such structures, the most advanced technical methods must be employed in their exploitation. Wherever possible, cycling and repressuring plants should be installed. 'here are presently in Louisiana, especially in south Louisiana, a great many fields that contain gas-condensate reservoirs. These reservoirs cannot be produced for their liquid hydrocarbon content under present conditions without wasting an enormous quantity of gas and creating underground waste. Although some of these reservoirs are being produced, such production must be considered in the nature of a salvage operation rather than as a sound economic proposition. Such reservoirs, however, can become profitable ven- tures through the use of cycling and repressuring plants. Cycling operations now operating in Louisiana have increased the ultimate recovery from gas-condensate reservoirs anywhere from 10 to 30 per cent. Cycling operations will also provide a considerable reserve of gas, without which Louisiana cannot hope to develop any program of industrialization. During the past year, Louisiana attained the rank of third among the oil-producing states of this country. With a proper program of exploitation and development, and with emphasis on conservation, Louisiana can maintain this position for a great many years. Production On Dec. 31, 1943, oil and/or gas were being. produced in 52 parishes, or 81 per cent of all the parishes in the state. Thirty-three of the parishes produced oil and gas, 14 produced oil, and 5 produced solely gas. Tensas Parish in north Louisiana and Assumption Parish in south Louisiana formerly contained no producing fields but during 1943 joined the ranks of the producing parishes. Twenty-three new fields, including one rediscovery, were found during 1943-—a rate of discovery almost comparable to that of the preceding year. Eleven of these new discoveries were either gas or gas-condensate fields. Thus, the trend of development in finding new reserves was also comparable to that of 1942. Many reasons of considerable merit have been advanced to account for the discouraging lack of crude-oil reserves found during the past year. None are, however, completely satisfactory.

Jan 1, 1944

By Hubert D. Keiser

An observation that is finding fresh confirmation in the leadership of the Allied Nations is "When the need arises, a man will rise to fill it." Much the same can be said of industrial advances in the current emergency. Events and circumstances have created needs for new materials and stimulated the inventive genius of man to fill them. The timely development of fibrous-glass manufacture, in relation to present war needs, is a case in point. Historical Summary It is probable that the first glass fibers produced by the hand of man were made about 4000 years ago. Successful production of glass fibers for manifold industrial and military uses, on any scale that could begin to meet present needs, has a history spanning a scant four years. The American processes that brought this young industry into being were developed between the years 1931 and 1937; research and manufacturing efforts were consolidated to create a commercially satisfactory operation as late as November 1939. In the 40 months that have elapsed since then, the industry has achieved commercial importance, supplied immense quantities of materials for pre-war industrial expansion to meet "defense" and Lend-Lease needs, and now has reached such importance that it has come largely under the control of the War Production Board for equitable distribution of its major products among 13 claimant agencies. It is worthy of note, however, that the Bureau of Ships, Navy Department, began exploratory use of fibrous-glass products in 1932, within one year after the date of the first experimental trials of the new process. This early recognition of the military importance of fibrous glass gave impetus to further research work. The foregoing rapid scanning of historical development must be filled in, lest the. impression be created that glass fibers were suddenly created out of thin air, with no antecedent trials, failures, and partial successes. The actual history of glassmaking is lost in antiquity. Probably some nomadic tribesman found molten glass beneath the bed of a hot campfire built upon sand of the proper composition. If his curiosity led him to poke the glowing, viscous pool with a green-wood stick or some handy weapon, it is probable that he drew a glass fiber on the end of his implement. Molten glass has much the same consistency as honey or molasses; it strings out tenuously. Thus, it is quite possible that the first form of glass shaped by man's action was a glass fiber. Artisans in glass, throughout the long Direc- of glassmaking as an art> drew fibers from fine rods for many decorative applications, including "spun glass" decoration in beautiful stemware and the charming millefiori (glass flowers encased in solid glass), and even to create the blood vessels in glass eyes to match a bleary mate.

Jan 1, 1948

By L. G. Sprague

The fact that this latest and most modern of the Universal Atlas Cement Company's plants at Northampton, Pa., is the fifth to be built on these same properties, and their development has been coincidental with the development of the portland cement industry in the United States, makes it appropriate to sketch briefly the history of the successive steps. In 1889 the original Atlas Portland Cement Co. started its first plant at Coplay, Pa., which is just across the Lehigh River from the present operation. Here the first successful rotary kiln was operated. These kilns were 6 ft. in diameter and 60 ft. long; they used oil for fuel until 1895, when the company developed the first burner for pulverized coal. Shortly thereafter the Atlas company acquired property on the Northampton side of the river and built its plants Nos. 2, 3 and 4 within the following 10 years. During the same period the production of portland cement in the country was increasing rapidly; owing largely to the development of the rotary kiln and improved grinding machinery, which lowered the cost and improved the quality of cement. The general tendency has been to increase the length of the kiln and grind both raw material and finished product Liner. In 1930 the Atlas Portland Cement Co. and the Universal Portland Cement Co. united to form the Universal Atlas Cement Co., and the same policy of improving the product has been continued. Because of the large amount of research carried on by manufacturers and consumers, including government agencies, there is a demand for cement of different chemical and physical characteristics for different kinds of structures. Hence many engineers in recent years have been asking for cements of certain definite chemical analyses, which they think are best for their particular jobs. This has compelled the manufacturer to make several different types of cement by variations of chemical composition. These are generally made by adding silica, iron and lime to the standard mixture, which necessarily increases the cost of the product. Therefore the Universal Atlas Cement Co., in planning the modernization of its Northampton plant, gave this particular phase of the problem considerable study. Research and experimentation have developed the practicability of making a wide variety of differently proportioned raw materials for cement by a process of subtraction rather than by addition. With such process, it is possible to discard the undesirable aluminates and silicates from the ample supply of impure limestone available from the company's property rather than by adding high-grade limestone obtained from distant sources. This procedure requires mineral separation by centrifugal sedimentation and froth flotation. Since the chemical and mineral constituents of Lehigh Valley "cement rock," together with the methods of separating them, have been thoroughly described in published

Jan 1, 1948

By F. R. Archibald, C. M. Nicholson

The present paper may be considered complementary to an earlier contribution on the same subject by F. R. Archibald and C. F. Jackson.1 It is particularly concerned with engineering and technological aspects of the operations at the Harleyville Alumina Plant during its period of operation from January 1945 to July 1946. The plant was built for and operated by Ancor Corporation, at Harleyville, South Carolina, as part of the government sponsored wartime program related to alumina production from domestic raw materials. The main purpose of the program was to secure technical and engineering data, based on actual plant experience, that might serve as a foundation for large scale production of alumina from raw materials other than bauxite. The Harleyville plant was directed specifically to treatment of clays found in very extensive deposits in the Carolinas and Georgia using the lime-sinter process developed by Ancor Corporation. It is considered that the purpose stated above has been served and this paper is to record and discuss some of the more important findings. The main factor in location of the plant at Harleyville was the presence in that locality of a rather remarkable deposit of high calcium limestone. The clay mining operation was centered near Aiken, S. C., and although a rail haul of ninety miles was involved there were, at the time, factors favorable to the Harleyville location offsetting, in part, the cost of transportation of clay, There are, no doubt, locations in the general area where clay and limestone deposits may be found in closer proximity hut they had not been proven up when the project was undertaken. Availability of power from the Santee-Copper development whose high tension line skirted the Property; ready access to rail and highway transportation; the promise, realized in actuality, of ample supply of soft water; and availability of labor supply were other factors of importance. Moreover, the general area has the decided advantage, for this type of operation, of a mild climate. Construction was begun in August 1943, and although stopped for a time priding review of the general situation that fall, it was resumed, albeit with less urgency, and substantially completed by the end of 1944. The total capital cost was approximately $3,460,000 The first alumina was turned out in April 1945 and from then until the plant was closed down in July 1946, the operations followed a succession of periods of production alternating with periods in which minor alterations were made in conformity with experience. Steady improvement was made and at the time Operations were discontinued it was considered that experience and the necessary engineering were in shape for removal of the remaining bottlenecks and a somewhat major revision in one section of the plant. Unfortunately this could not be carried out and it was necessary to discontinue the

Jan 1, 1949