Search Documents

By F. O. Garrabrant, F. S. McNicholas, Robert Henderson, R. U. King

Several years ago, it was decided to experiment with the use of high-pressure water to bring in finger hangups and reduce the amount of secondary blasting necessary. It was argued that the velocity effect of the high-pressure water would bring down hangups without unduly wetting the ore. Water under a head of about 550 ft. was installed in certain slusher drifts. Ordinary ¾ in. water hose, with a nozzle opening of % in., was used, and water was impinged on the fines under a hangup. Results were excellent. About half the total number of hangups were brought in with high-pressure water without blasting and the cost of this part of the slushing operation was reduced about 50 per cent. Operations were speeded up, dust counts and safety hazards were reduced, and a more desirable working place was secured. The additional water added to the ore was under one per cent and caused no inconvenience in slushing, haulage, or crushing operations. Usually the ore would absorb all of the water, so that none of it would enter the loading drifts. The entire mine, developed by slusher drifts, is being equipped with high-pressure water. Heating Mine by Compressor Cooling Water Several years ago, the problem of heating certain sections of the mine during freezing weather became important. It was calculated that there was sufficient heat in the compressor cooling water to heat the incoming ventilating air current to above freezing, if such heat could be transferred from the water to the air. All schemes of radiation from pipe were rejected as too cumbersome, costly and impractical. It was thought that by spraying the heated water from the compressor cooling system into the incoming air, a satisfactory heat exchange could be accomplished. The only objection was that the sprayed water would freeze and might fill the air-intake drift. However, when water at about 75° to 80°F. was sprayed at the rate of 200 gal. per minute through a bank of sprays into the incoming and freezing air current, this air was thereby heated to above freezing; and although some ice was built up in the air drift, the amount was not objectionable. Occasionally the built-up ice was picked down into the outgoing water stream, which removed it. The entire south and westerly parts of the mine were prevented from freezing. Concreting for Hangups Considerable trouble was experienced in securing hangups of fine ore in slusher fingers that needed repairing. Regular methods of timbering were unsatisfactory. Now, a slab of concrete is poured over the top of the muck by Pumperete machine, almost filling a finger, which gives a satisfactory slab to work under for making the needed repairs. Derailers Some trouble has been caused by motor-men not observing safety lights and

Jan 1, 1946

By A. C. Polk, R. H. Smith

The physical properties of the materials are listed, together with a short explanation of how this material binds the sand grains together without materially reducing the effective permeability of the sand. The chemical can be used in wells with bottom-hole temperatures ranging from 105°F to more than 350°F A description of the equipment required and the techniques used for applying these plastics to the wells is included. Introduction Recovering oil and gas from unconsoli-dated sand formations offers one of the most troublesome of all production problems. These sands generally present no particular trouble while drilling is in progress, but after the well has been completed and a pressure differential has been established across the face of the producing zone, the formation begins to L'slough," resulting in "sanding up" of the well. The term "sanding up" means that sufficient volumes of sand have moved into the well bore or casing to cause a serious reduction or complete halt of all flow of oil, water or gas. In rare cases a well may produce only a small amount of sand and still continue to flow or pump, the sand being carried to the surface in the fluid stream. However, in such instances, the result may be a costly repair bill due to the effect of the sand on surface and pumping equipment. The difficulty of producing petroleum from sands that are loosely cemented has long been recognized by petroleum engineers but only within the last few years has any new approach to the problem been undertaken. This involves the use of plastics that are capable of bonding the individual sand grains in place without materially reducing the effective permeability of a formation. The successful application of plastics for the consolidation of poorly cemented sands is relatively recent but now it is widely used in many of the more difficult areas on the Gulf Coast of Texas and Louisiana. This relatively new use of plastics1 in the oil fields has been preceded by much laboratory and field research on the use of various chemicals2,3 for solving numerous well-completion and work-over problems. Plastics now are being used successfully to control gas-oil and water-oil ratios,4'6 in zone isolation, the repair of casing leaks, the elimination of caving in cable-tool drilling wells6'7 and in the setting of linerss and casing.9 Sand-consolidating plastics, however, are basically different from all others in that they must not form an impervious seal. Field Practices The approach to the sanding-up problem usually has been the mechanical obstruction of the movement of the sand grains.

Jan 1, 1947

By Lester C. Uren

THIS paper reviews the industrial trends and changes in educational concepts that have led to the development of the modern petroleum engineering curriculum. A trend toward emphasis on engineering fundamentals is noted. While most universities are committed to the traditional four-year engineering program, it is agreed that more than four years is necessary for academic preparation of the petroleum engineer in all phases of his profession. The author proposes a coordinated program of undergraduate and graduate training that will permit of adherence to the general pattern of the present four-year engineering course, with provision for extension of the program into specialized graduate courses of professional character. In the latter, emphasis may vary with the interests and objectives of the individual student. A specific undergraduate curriculum is proposed in which upward of 80 per cent of the available time is devoted to engineering fundamentals. A broad survey of the professional field is afforded in courses grouped in the third and fourth undergraduate years, but detailed treatment of the professional aspects of petroleum engineering is reserved for the graduate program. INTRODUCTION Of necessity, engineering curricula must ever be changing to reflect the new techniques, the changing concepts that are presented as the engineering industries develop and unfold. Particularly is this true of the younger engineering curricula representing comparatively new and rapidly changing industries such as the petroleum industry. Institutions that planned their petroleum engineering curricula a decade or two ago now find that the petroleum industry has become vastly more technical in its requirements. Entirely new methods and techniques have come into vogue and must be given place in the curriculum, and some of these are of a character that demands changing emphasis in the fundamental preparatory subjects. College and university faculties cannot complacently assume that curricula in this field that were considered appropriate 10 or 20 years ago still reflect the needs of the industry that they are designed to serve. If they do, their graduates will be poorly equipped to meet the requirements imposed upon them by a rapidly changing industry. Perhaps it is not too much to expect academic authorities to anticipate the trends of industry and equip their graduates with what they will need to attain leadership 10 or 20 years after graduation. Whether or not this desirable objective is possible, there is no excuse for allowing curricula to fall behind the current needs of industry. DURATION OF CURRICULUM The majority of our engineering schools and colleges still adhere to the four-year curricula and there appears to be a definite - sentiment among many engineers engaged in industry that work should be so planned that the engineering student may secure the essential academic preparation for his profession in a terminal four-year program. Yet, in recent years, it has become increasingly apparent that four years of

Jan 1, 1941

By Charles S. Barrett, L. H. Levenson

Numerous determinations1-' of the texture of cold-rolled polycrystalline iron, steel, and ferritic alloys have been made with good agreement among the various observers as to the principal features of the texture common to all, but there has been no adequate explanation of the texture in terms of, the behavior of individual grains. This study presents an explanation of the texture based on the observed rotation of single crystals when deformed in a manner similar to a grain in the aggregate, a method we have found useful in leading to a better understanding of compression and tension textures;8,9,10 in particular, the aim has been to determine experimentally the end orientations of rolled single crystals of iron. These are discussed in connection with the point of view of Weverl and of Boas and Schmid2 that the rolling texture is a simple compression texture (compression normal to the rolling plane) superimposed on a simple tension texture (tension in the rolling direction), and the point of view of Kurdjumow and Sachs3 that three ideal end orientations exist. Experimental Method The single crystals used were in the form of disks cut from a stock of crystalst pre- pared in this laboratory by a strain-anneal method from mild steel decarburized and purified in hydrogen, the details of which have been described elsewhere.11 To ensure maximum elongation in the rolling direction and to simulate approximately the rolling of a grain in an aggregate, lateral flow was constrained by placing each crystal in a close-fitting hole in a plate of copper or iron of equal thickness and rolling the plate and crystal together. About one-third of the crystals were rolled in a "sandwich" pack by adding top and bottom cover plates. The two-high mill used had 8-in. diameter rolls and was operated at 15 r.p.m. The initial diameter of the crystals was between 1/4 and 1/2 in., while the starting thickness varied from 0.031 to 0.376 in. With a single exception, which was rolled 63 per cent, the crystals were rolled to a final reduction in thickness of 82 to 97 per cent in 20 to 40 passes, alternately changing the sense of the rolling direction. The initial orientations of the crystals were determined either by X-ray back reflection12 or by optical reflectionl3 from etch pits; the mean final orientations were determined by X-ray Laue photograms using molybdenum, silver, or tungsten radiations, by optical reflection, and in many cases by both methods. Results Twenty-six crystals were studied. It was found that there were three typical be-

Jan 1, 1941

By Harold Vagtborg

Equilibrium vaporization ratios were obtained for light hydrocarbons, nitrogen, carbon dioxide, and hydrogen sulfide in a reservoir fluid containing 35 mole per cent hydrogen sulfide. The data cover the range from 700 to 2500 psia at 154°F. The results of this study are compared with results obtained by other investigators on systems containing less hydrogen sulfide. When large amounts of hydrogen sulfide are present, the equilibrium vaporization ratios for ethane and heavier hydrocarbons are greater than the ratios for systems containing little or no hydrogen sulfide. Large amounts of hydrogen sulfide have the reverse effect on the ratios for methane. Routine PVT studies were performed on the reservoir fluid including flash and differential liberations of the dissolved gas. The pressure-volume relationships of the saturated fluid were also determined. It is shown that the use of published correlations on physical properties of reservoir .fluids can lead to gross errors when applied to systems containing large amounts of hydrogen sulfide. INTRODUCTION Equilibrium vaporization ratios for various components in naturally occurring crude oil and condensate systems have been reported in the literature.1,2,3,4 Recently, several papers have been published with emphasis on non-hydrocarbon components such as nitro- gen, carbon dioxide and hydrogen sulfide.5,6,7,8,9 The increased discovery of reservoir fluids having high concentrations of these non-hydrocarbon components, particularly hydrogen sulfide, has created a need for a further study of their phase behavior. Equilibrium vaporization ratios are known to vary with pressure, temperature, and overall composition of the system.'" It was anticipated that ratios for systems containing large amounts of hydrogen sulfide would differ from the ratios for systems containing small amounts of hydrogen sulfide. Therefore, the present work was undertaken in order to obtain reliable equilibrium vaporization ratios for the reservoir-fluid in question. PROCEDURE The procedure followed was evolved after considerable experimentation on methods of handling the very sour crude. It was found that drying agents (e.g. CaCl2 and CaSO4) absorbed an appreciable amount of hydrogen sulfide from the gas used to prepare the recombined samples. The concentration of hydrogen sulfide dropped as much as 10 mole per cent in a single pass through a 3-ft drying tube. It was also found that when undried gas was agitated with mercury in the PVT cell, a black scum, believed to be mercuric sulfide, was formed and the hydrogen sulfide content of the gas dropped several mole per cent. Because composition changes during a run could not be tolerated, separation of the mercury and sour fluid was necessary. In order to effect this separation, a stainless steel piston, equipped with Teflon O-rings, was placed in the PVT cell between the mercury and the sour fluid. This piston had to be constructed in three parts because

Jan 1, 1955

By A. T. Beckwith

The Lehigh Navigation Coal Company Inc. operates steep-pitch, relatively deep mines in the Panther Creek Valley, at the eastern end of the southern anthracite coal field. Commercially minable coal beds are the Mammoth,† Primrose, Orchard, and Buck Mountain;‡ their respective thicknesses average 50, 15, 10 and 12 ft. Sand slates immediately overlie and underlie these beds, though in some locations sandstone or conglomerate beds occur. Underground operations extend to a depth of 1200 ft. below the surface, and comprise a bulk of virgin work on the lower levels, and a small amount of remining on the upper levels. With increase in depth, ventilation has become a more important factor. Development In early days slopes or drifts were driven in the outcropping coal on the hillsides. Subsequent development was by water-level tunnels, with portals above high water in Panther Creek. These tunnels have been maintained because they intercept and drain much water that enters the mined-out portion of the bed and otherwise would follow down to the deep workings+ Below these tunnels, the coal was customarily developed by slopes. Muleways, which are zigzag chutes easy to travel, were also driven to connect lower openings with the water levels. When it became necessary to go still deeper, the slopes were abandoned, and vertical multicompartment shafts were sunk from the surface. Levels have been at vertical intervals of from 175 to 250 ft. Recent practice has been toward the latter spacing, splitting the total lift, however, by starting to mine from chutes extending halfway up to the level above. Chutes customarily are spaced at 50, 60 or 70-ft. centers along the gangways. At some mines, additional shafts have been sunk from the surface to the level containing the main pumping station, and these carry the discharge lines from the pumps. As the mines are ventilated by the exhausting system, both the hoisting and so-called water shafts serve as intakes. The main fan is always on the surface, and is connected with the return airways from the various levels by an air hole or a vertical shaft. For economy, when the present deepest levels were developed, and return-air shafts or air holes were not extended to the new level, but connections were made from the new level to that above by two or more holes. It is doubtful that this method will be continued, as complications in the system, increased resistance to flow, and other difficulties undoubtedly will counterbalance any economies this provision may afford. During the early years of mining, when operations were at no great depth, all development headings were driven in the coal bed. As mining progressed downward, increased ground pressures slowed develop

Jan 1, 1942

By L. G. Graper, E. L. Ramsey

THE present program of increased production of armament and lend-lease material for mechanized war has created a problem for the shops that must do the machining. They have naturally turned to the steel producers to provide them with a steel that can be accurately machined with the greatest possible speed. The adding of sulphur to steel as an aid to machinability has long been practiced; however, it may cause red shortness in rolling and may result in billets with seams and cracks, which must be removed before rolling can be continued. This conditioning of billets slows down production and' adds to the cost of making steel. Experience with various grades of sulphur steel made to different specifications has shown that Bessemer sulphur steels roll better than similar grades made in the open hearth, and also that low-carbon steels that are open or semikilled .as tapped roll better than completely deoxidized or killed steels. This has led to the belief that oxygen plays an important part in the rolling qualities of sulphur-bearing steels. It is generally held that the red shortness of sulphur steels is due to the low melting point of the sulphide compounds that separate out at the grain boundaries when the steel solidifies. At the rolling temperature of steel these sulphide compounds melt and cause cracking. ADDING SULPHUR AS A SULPHITE These difficulties can be avoided if sulphur is introduced into the steel by means of an anhydrous sulphite, such as sodium sulphite or sodium bisulphite, which-upon decomposition-forms sulphur dioxide. It is assumed that, in this case, the oxygen of the sulphur dioxide forms part of the sulphide inclusions in the steel, and raises their solidification temperature enough so that the formation in the steel of a low-melting eutectic is prevented. The result is the prevention of hot shortness and a more uniform distribution of inclusions. Fig. I shows photomicrographs of steels made with sulphur, while Fig. 2 illustrates the structure of steels made with sodium . bisulphite. These samples were cut from the steels as cast-that is, before rollingand were polished and lightly etched to bring out the grain boundaries. Fig. I shows that sulphide -inclusions segregate more or less at the grain boundaries, and it can be seen how the continuity of these low-melting inclusions would cause red shortness. Fig. z shows that the sulphide inclusions are more or less uniformly distributed throughout the matrix. This arrangement of inclusions has no apparent effect on the rolling qualities of a steel. This statement has been substantiated by the observation of the rolling of over 6000 tons of steel made with a sulphite addition. RESULTS As stated before, the sulphur dioxide-is added to steel by means of the decomposi-

Jan 1, 1942

By Blake M. Loring

RECENTLY the S-curves for 30 to 40 alloy steels have been published.1,2 These steels show individual characteristics, which make each additional S-curve of great interest. There are important differences in the mechanism of the transformation process, the type of transformation product, and the influence of alloying elements. Steels of the same general alloy composition may possess such variable characteristics with regard to the length of time of isothermal transformation that an S-curve for each heat of steel may be desirable. In the present work the isothermal transformation of a steel having the following composition and grain size was studied: 0.20 percent carbon; 0.21 manganese; 0.026 phosphorus; 0.017 sulphur; 0.056 silicon; 1.45 chromium; 3.25 nickel; austenite grain size, 7. The progress of the isothermal transformation was followed by several different methods, including hardness measurements, dilatometer observations, and examinations of the microstructure. It was not expected that these methods would be in precise agreement.3 Accordingly, the changes in microstructure and hardness were given additional weight in determining the initial stage of transformation and the dilatometer measurements were relied on in estimating the completion of the process. The beginning of transformation was indicated by I per cent of transformation products and the end of transformation by about 99 per cent. The reproducibility of the various methods in the ranges of highest sensitivity was checked by several observations at each time and temperature. The steel used in this investigation was annealed for 24 hr. at 925°C. Macroetching revealed no serious segregation. The specimens for the metallographic and hardness investigations were 1 1/4 by 1/2 by 1/8 in. Wires attached to the samples were used for handling, instead of tongs, to avoid chilling. The specimens were heated at 845°C. for 1/2 hr. and quenched into constant-temperature salt baths held at various temperatures from 205° to 650°C. The time required to transfer the specimens was found to be about x 1 1/2 sec., and nearly 5 sec. more was required for them to come to the temperature of the bath. After various lengths of time in the constant-temperature baths the specimens were quenched in water at 21°C. The specimens were cut in half for the metallographic examination, to provide a surface free from decarburization. To determine the beginning and end of the transformation the percentage of transformation determined metallographically and by hardness was plotted against time. A planimeter was used in the metallographic determination. The hardness and metallographic determinations made at room temperature were confirmed reasonably well by dilatometer measurements taken during the process of transformation at the various temperatures. Two dilatometers were used to

Jan 1, 1941

By T. J. Nowak

The heat flow processes determining the injection and shut-in temperature logs in a water injection well have been analyzed and the theoretical basis for determining the water injectivity profiles from the temperature logs has been presented. Both the injection and the subsequent shut-in logs are necessary to resolve the injection interval into relative water intake strata; the former, to provide an accurate estimation of the thicknesses of the strata, and the latter to indicate the major and minor intake rates into the strata. A procedure is described for estimating the injectivity profile from the temperature logs and is applied to several temperature logs. For a water injection well, a comparison is made of the injectivity profiles obtained from the core analysis, the spinner survey, and the temperature logs. INTRODUCTION In secondary recovery of oil by water flooding, the injectivity profile is needed to obtain diagnostic evaluation of water intake distribution over the injection interval. If the distribution is unfavorable among the various strata, corrective measures can be taken to provide better control. Numerous methods have been developed for determining the injectivity profile from water velocity measurements in well bores. Often, dependence is placed upon core analyses and/or electric logs for estimating the relative water intakes over the injection interval. In many cases, the temperature log method described herein will give results more diagnostic than those obtained through use of the other available methods inasmuch as it is based upon the study of temperature disturbances in and around the well bore as a function of water flow in the well bore and in the formation. This method is the result of analyses of a number of temperature surveys made in water injection wells to determine the point of entry of the water into the formation. The material in this paper is presented in two sections: the first deals with the theoretical study of temperature survey data, and the second deals with the field application. PART I — THEORETICAL TREATMENT OF TEMPERATURE LOG DATA Before discussing the various aspects of heat flow relative to temperature log data, the phenomena that give rise to well bore temperatures — namely, the indigenous formation temperature and the associated rates of heat flow — will be considered. Geothermal Gradient The geothermal gradient is defined as the increment of depth at which the indigenous subsurface temperature increases by l°. It is caused by the continuous flow of heat outward from the interior of the earth. The flow of heat is an equilibrium process between the heat sources, the thermal conductivities of the formations, and the mean surface temperature. Therefore, there is no accumulation of heat energy in the path of heat transmission, and the geothermal gradient for a given formation will depend upon its thermal conductivity.

Jan 1, 1953

By R. J. Teitel

FOUR or five years ago an investigation was initiated to study and develop basic information on llquid metal fuels for future power nuclear reactors. The objective was to find fluid forms of uranium (solutions or dispersions) in low melting alloys. A summary of the different fuels was presented in a recent article by Teitel, Gurinsky, and Bryner.' The combination of uranium and bismuth, with its low thermal neutron cross section and low melting point, is of basic interest to the development of these fuels. Most of the previous effort on the U-Bi phase diagram was done under security regulation. Ahmann and Baldwin' reported their findings on the U-Bi system in 1945. Their results indicated that the phase diagram had at least two compounds and possibly one more. UBi, and UBi were established by chemical analyses of residues after high temperature centrifugation of alloys. UBi, decomposed peritectically at1980°C and there were signs of another reaction above that. UBi melted at a very high temperature, and there were also signs of a monotectic at high temperatures in high uranium alloys. The solubility of uranium in liquid bismuth has received attention by three groups of authors: Bareis,X ayes and Gordon,' and Ahmann and Baldwin.' The latest and most widely accepted data is that of Bareis, and it is included in Fig. 1 along with new data at higher temperatures. Brewer et al." and Ferro"'' have used X-ray diffraction to determine the number and crystal structure of the compounds. Brewer identified the structure of UBi to be a simple NaCl cubic structure having a cell edge of 6.364A. The density of the compound was calculated to be 11.52 g per cu cm. Two other unindexed patterns were presented as possibly belonging to two other compounds. Ferro agreed with Brewer on the crystal structure of UBi and identified the structure of UBi, and U,Bi,. The intermetallic compound UBi, has a tetragonal cell with a = 4.445A and c = 8.908A. The density of the compound was determined and the number of atoms per cell (six atoms) was calculated. The X-ray density reported was 12.35 g per cu cm. The compound UsBir was treated in a similar way and it was reported to have a cubic structure 9.35A on an edge and to contain 28 atoms per cell. The density was given as 12.59 g per cu cm. Teitel reported that there was a compound UaBi, and no UBi, compound. (The difference in the compositions is 3.3 pct U.) This conclusion was based upon the extrapolation of some 20 tie lines in the

Jan 1, 1958

By H. l. Burghoff, C. H. Mathewson

THE study of the creep of metals under conditions of prolonged loading has received the attention of many investigators for several years and almost innumerable papers have been published on the various aspects of the subject. As it appeared that much could still be learned from a study of single crystals, the present work was carried out to study the effects of temperature and conditions of loading upon the properties and deformation in tension of single crystals of alpha brass containing about 70 per cent copper and 30 per cent zinc. In particular, it was hoped to obtain information from tests below and above the recrystallization temperature of the material, so that properties such as elastic limit, yield point or critical stress, and manner of deformation might be compared for tensile tests at an ordinary loading rate and for prolonged. loading. Accordingly, short-time tensile tests and creep tests were made at room temperature, 300º, 500° and 700°F. The two latter temperatures are above the lowest possible recrystallization temperature of polycrystalline 70-30 brass. PREVIOUS WORK Clarke and White1 have made creep tests of some copper-zinc alloys, including 70-30 brass, and copper-zinc-tin alloys at temperatures both below and above the recrystallization temperature of the materials considered. Hanson and Wheeler have studied the flow and fracture of single crystals of aluminum for short-time and prolonged tensile loading over a range of temperature extending from room temperature to 400°F., their experiments being made without consideration of the orientations of the test specimens. Extensive creep and fracture tests on single crystals of lead at room temperature have been made by Betty3 and by Baker, Betty & Moore.4 Results of the last-named investigation were published while the present work was in progress. Millers examined the elastic limit of zinc single crystals at and above room temperature by means of creep tests, while Miller and Milligan6 reported the results of tests designed to show the influence of temperature on elastic limit of single crystals of aluminum, silver and zinc. The behavior, of iron crystals under static tensile loading at room temperature was reported by Gensamer and Mehl7 while the present investigation was in progress. Their specimens exhibited a well-defined yield point, below which no appreciable creep could be detected. The manner of yielding proved interesting, as the shape of the creep-time curve for the iron crystals differed from the common type of creep curves. Elongation did not begin immediately, or at least was initially very slow. The rate of elongation then increased continuously and finally decreased to zero. This S-shaped type of elongation-time

Jan 1, 1941

By R. W. Gurry

IN the course of a series of measurements of the rate of diffusion of carbon in austenite at about 960°C. (1760°F.) and 1110°C. (2030°F.), it became necessary to determine carbon concentration when austenite is saturated with graphite, because of indications that the hitherto accepted value of the solubility of graphite in this temperature range is too low. Specimens of carbonyl iron were saturated at temperature in a hydrogen-toluene atmosphere which was in equilibrium with graphite. The carbon content of the steel was measured either by combustion or by the loss of weight after substantially complete decarburization in an atmosphere of hydrogen saturated at room temperature with water vapor. The absence of carbide or graphite as a phase at temperature was demonstrated by microscopic examination of saturated specimens that had been drastically quenched. The mean result of concordant measurements is that gamma iron saturated with respect to graphite contains 1.39 per cent carbon at 957°C. (1755°F.) and 1.89 per cent at 1110°C. (2030°°F.). These two values, plotted along with what appears from the literature to be the best value (0.69 per cent) at the iron-graphite eutectoid temperature (738°C. or 1360°F.), yield a curve that is almost linear, and which, continued upward through a short interval, leads to a limiting solubility of 1.98 per cent at the iron-graphite eutectic temperature1135°C. (2095°F.) instead of the commonly accepted value of about 1.7 per cent. EXPERIMENTAL PROCEDURE The samples of carbonyl iron, with the exception of those for microscopic examination, were cylinders 3.8 cm. long, 0.475 cm. in diameter. They were placed in a graphite holder and suspended in a vertical furnace, the temperature of which was controlled precisely by means of the resistance of the platinum winding.1 In the empty furnace the range of temperature over a distance of 4 cm, at the heat center was 9°C. (16°F.) but at a given location the temperature remained within ±0.5°C. (0.9°F.); it was measured by inserting a platinum-rhodium couple calibrated at the melting point of palladium, 1555°C. Since the presence of the sample probably improved the uniformity of temperature, it was decided to consider the average temperature of the sample to be 3°C. lower than the maximum measured in the empty furnace with the same setting of the controller. Data were obtained in the vicinity of two temperatures, 960°C. (1760°F.) and 1110°C. (2030°F.). The samples for microscopic examination, 2.2 cm. long, 0.475 cm. in diameter, were suspended individually on pure iron wire; for these no temperature correction was applied. The carburizing gas passed into the furnace was dry, oxygen-free hydrogen saturated at room temperature with

Jan 1, 1942

By A. H. Daane, B. J. Beaudry

The uranium-antimony system has been investigated by metal-lographic, therma1, and X-ray methods. There are four intermediate phases present: USbz and U,Sb, which undergo peritectic decomposition at 1355°and 1695OC, respectively, and USb and UPSbs which melt congruently at 1850"and 1800°C, respectively. There is a eutectic between U4Sbs and USb which melts at 1770°C. USb,, UsSb4, and USb are line compounds while U4Sbs has a solubility range of approximately 1.5 at. pct at 1770°C. Single crystal studies of the cmpo,und U.,SbS show it to have a hexagonal unit cell with a, = 9.268A and c, = 6.201b;. The solubility of uranium in liquid antimony increases from 0.1 at. pct at 650°C to 1.5 at. pct at 900°C. The solubility of antimony in a, P, and y uranium is approximately 0.02, 0.1, and 0.05 at. pct respectively. IN nuclear reactors, uranium has been used mainly in the form of solid-fuel elements of the pure-metal or uranium-rich alloys. However, in attempts to overcome some of the difficulties inherent in solid-fueled reactors, reactor concepts hive been proposed in which the fuel would be a liquid metal, such as a solution of uranium in another metal. The liquid-metal fueled reactor (LMFR) designed by the Brook-haven National Laboratory of the U.S. Atomic Energy Commission is an example. Fuel for this reactor is a solution of approximately 800 ppm enriched uranium in bismuth.' To design such liquid-fueled reactors, a background of information on the solubility of uranium in various metals is obviously necessary. The present study was undertaken to pro- vide information for such purposes, and in addition, to study the uranium-antimony system as a whole. A preliminary literature search showed that some work had been done previously on uranium-antimony alloys, but no attempts had been made to make a complete study of this system. The solubility of uranium in antimony was studied by Cammack and Bridger' up to 950°C and by Hayes and Gordon up to 900'-C. Their data are plotted in Fig. 1. Ferro, in an X-ray structure study of some uranium-antimony compounds, found USg to be tetragonal with a, = 4.2724 and c, = 8.471A, U3S4 to be b.c.c. with aO = 9.095A and USb to be f.c.c. with a,= 6.191A. Colani reported the compound UsSba; however, work by Ferro and by this Laboratory showed that this compound does not exist. foote' reported several intermediate phases in the uranium-antimony system, but did not identify them. Greninger' re-ported finding an intermediate phase in a 5 at. pct Sb

Jan 1, 1960

By K. K. Rao, M. E. Nicholson

IN a recent paper on the solubility of carbon in Ni-Cu alloys,' Nicholson reported that the carbon solubility appeared to be limited by the electronic structure of the alloys and that the solubility was propor- tional to the density of states at the Fermi surface of the "3d" band. In order to determine whether or not this relationship is a general one, the study has been extended to other systems. One of these is the CO-Ni system. This system was chosen for study because 1) it is adjacent to Ni-Cu system in the periodic table, 2) the alloys of cobalt and nickel do not form stable carbides at 1000°C, and 3) the system exhibits no pronounced change (less than 1 pct) in lattice parameter from cobalt to nickel,' see Fig. 1. The alloys were prepared from -200-mesh 99.92 pct Ni furnished by the International Nickel Co. and spectroscopically pure -200-mesh cobalt sponge obtained from Johns on-Matthey and Co. The powders were weighed, mixed, and pressed using a pressure of 40,000 psi. The samples were sintered for 24 hr at 900° C in dry hydrogen and then cold rolled to a thickness of 0.010 in. (Samples containing more than 70 wt pct Co had to be annealed after cold reductions of about 20 pct to avoid cracking.) The alloys were carburized at 1000°C in an alun-durn boat containing Acheson AUC powdered graphite in an atmosphere of carbon monoxide cylinder gas which had been passed through Ascarite to remove carbon dioxide. After carburizing for either 12 or 24 hr the samples were moved to a cool zone of the furnace to cool. Cooling required about 5 min. The samples were filed to remove about 0.005 in. from the surface and then analyzed using a conventional combustion-gravimetric analytic method. The results of this investigation are shown in the lower portion of Fig. 1 and Tabulated in Table I. The nickel percentages for these alloys were determined from the weights of the powders from which the alloys were made. The solubility of carbon in pure cobalt at 1000°C (fcc) is 0.25 wt pct. This is somewhat less than the 0.33 wt pct measured by Boecker.3 From his data, it would appear Boecker's samples were supersaturated before the equilibrating treatment and that a 20-min treatment was not long enough to achieve equilibrium. Since in the present investigation the 12 and 24 treatments produced essentially equal carbon contents, our figure is presumed to represent more nearly the equilibrium value. The solubility of carbon in nickel of 0.19 wt pct agrees quite well with the value of 0.21 wt pct

Jan 1, 1963

By Robert P. Burrows

Discussion of the paper of R. P. Burrows, presented `at the New York meeting, February, 1916, and printed in Bulletin No. 107, November, 1915, pp. 2237 to 2245. EDWIN M. CHANCE, Wilkes-Barre, Pa.-I have been very much interested in the comprehensive and able discussion of the important topic of mine lighting just given by Mr. Burrows, especially as I know by common report Mr. Burrows' ability and his close touch with the development of the electric mine lamp, and its use in mines in connection with a portable electric lamp. It is regrettable that Mr: Burrows was not able to acquaint himself more closely with the cost of mine illumination, the actual cost, as produced by a portable light as carried by miners, whether a flame safety lamp or an open light. Had he been able to acquaint himself more closely with these data, he perhaps would not have arrived at some of the conclusions which he has presented to us in his paper. For example, we find Mr. Burrows advises that the open torch is by far the cheapest source of illumination, as produced by a portable light. I am very sure that is not the fact. The cost of miners' oil varies from about 25.c. a gallon to 90b. a gallon. The various States have passed laws from time to time rendering it mandatory that the miner shall use, whether he is willing or not, a so-called better or higher grade of burning oil. These laws have entailed the use of an oil so expensive that the use of the oil torch has become practically impossible, and the acetylene or carbide miners' lamp has largely taken its place. I have evolved a few figures showing the relative efficiency and usefulness of the open oil torch and the acetylene miners' lamp. For example, the acetylene miners' lamp consumes or burns 4 liters of acetylene per hour, or 0.14 cu. ft.; the oxygen consumed is 10 liters, or 0.35 cu. ft. per hour; air consumed, 50 liters, or 1.76 cu. ft. per hour; black-damp produced, 40 liters, or 1.41 cu. ft. per hour; air rendered extinctive to the acetylene flame, 112 liters, or 3.95 cu. ft. per hour; carbide con- sumed, 13 g. per hour. The open oil torch, on the other hand, burns about 20 g. of oil per hour; the oxygen consumed is 48 liters, or 1.69 cu. ft. per. hour; air consumed, 240 liters, or 8.47 cu. ft. per hour; blackdamp produced, 191 liters, or 6.73 cu. ft. per hour; air rendered extinctive to oil flame is 1,413 liters, or 49.92 cu. ft. per hour.

Jan 5, 1916

By Frank G. Miller

The lower cost of producing oil from naturally flowing wells compared with pro-luction costs accruing from artificial lifting methods has stimulated much research, rith the joint purpose of extending the natural flowing life of wells and of increas-ng the productivity of small wells. The iboratory investigation described herein was made to determine the effect of a lotted liner on the pressure gradient in the icinity of the wall of a flowing well. Flow estrictions caused by the liner induce nergy losses between the oil-bearing for-lation and the inside of the liner, which lay be reduced by improved liner design, nd thereby the flow capacity of wells may e increased. These losses have been evalu-ted for rectangular slots of different sizes, nd means are suggested for reducing them. The dearth of information concerning the ature of the flow of fluids from uncon-slidated sands through small openings in he walls of. pipes—as represented by the ow of oil from an oil sand into a slotted ner—is acknowledged. Although the bene-ts to be realized by operators through the se of optimum liners is just beginning to e recognized generally, Coberlyl in 1937 ointed out that the functioning of screen is is an important factor in the pro-uction of oil. From his study on the :lection of size of oil strings for wells in California, Parks2 concluded, in part, that the perforated section of the oil string deserves continued study, especially with respect to the selection of perforations. The growing use of gravel packing resulting from certain research findings lends even more significance to the problem of selecting optimum liners, as the application of these methods usually requires slotted liners or other kinds of perforated liners. The present study was made to obtain further information for the guidance of engineers and operators in selecting slotted liners and to develop a laboratory method that may be used in analyzing possible pressure conditions surrounding most types of perforated casings used in producing oil wells, so that the present inadequate fund of knowledge on this important subject may be expanded. Discussion of ProbleM At the beginning of the investigation the following assumptions were made regarding bottom-hole conditions of a producing oil well and the oil-sand reservoir it penetrates: (I) Conditions of steady-state flow exist, (') a a homogeneous liquid is being produced) (3) no contaminating material (such as drilling fluid) is present between the liner and the face of the oil-bearing sand, (4) the well is vertical and completely penetrates a horizontal sand stratum of uniform thickness occurring between two impermeable strata, and (5) the flow is wholly viscous. If the foregoing assumptions are made, with the added requirements that the sand

Jan 1, 1941

By C. H. Mathewson, H. l. Burghoff

The study of the creep of metals under conditions of prolonged loading has received the attention of many investigators for several years and almost innumerable papers have been published on the various aspects of the subject. As it appeared that much could still be learned from a study of single crystals, the present work was carried out to study the effects of temperature and conditions of loading upon the properties and deformation in tension of single crystals of alpha brass containing about 70 per cent copper and go per cent zinc. In particular, it was hoped to obtain information from tests below and above the recrys-tallization temperature of the material, so that properties such as elastic limit, yield point or critical stress, and manner of deformation might be compared for tensile tests at an ordinary loading rate and for prolonged loading. Accordingly, short-time tensile tests and creep tests were made at room temperature, 300°, 500° and 700°F. The two latter temperatures are above the lowest possible recrystallization temperature of polycrys-talline 70-30 brass. Previous Work Clarke and White1 have made creep tests of some copper-zinc alloys, including 70-30 brass, and copper-zinc-tin alloys at temperatures both below and above the recrystallization temperature of the materials considered. Hanson and Wheeler2 have studied the flow and fracture of single crystals of aluminum for short-time and prolonged tensile loading over a range of temperature extending from room temperature to 400°F., their experiments being made without consideration of the orientations of the test specimens. Extensive creep and fracture tests on single crystals of lead at room temperature have been made by Betty3 and by Baker, Betty and Moore." Results of the last-named investigation were published while the present work was in progress. Miller5 examined the elastic limit of zinc single crystals at and above room temperature by means of creep tests, while Miller and Milligan6 reported the results of tests designed to show the influence of temperature on elastic limit of single crystals of aluminum, silver and zinc. The behavior of iron crystals under static tensile loading at room temperature was reported by Gensamer and Meh17 while the present investigation was in progress. Their specimens exhibited a well-defined yield point, below which no appreciable creep could be detected. The manner of yielding proved interesting, as the shape of the creep-time curve for the iron crystals differed from the common type of crcep curves. Elongation did not begin immediately, or at least was initially very slow. The rate of elongation then increased continuously and finally decreased to zero. This S-shaped type of elongation-time

Jan 1, 1941

By D. P. Morton

Since 1923, which closed the speculative era in the bituminous coal fields of the United States, there have been wide annual fluctuations in the national production of bituminous coal. These changes in annual output have been variously attributed to: (1) increased competition from petroleum products, natural gas and hydroelectric power; (2) lower unit consumption of coal; and (3) fluctuations in the general business level. The purpose of this paper is to measure, from a practical standpoint, the net effect upon the annual trend of bituminous coal production, and to give those who are interested a basis for estimating in advance the probable output of bituminous coal. It can readily be shown that changes in the level of general business affect the national production of bituminous coal more than does any other factor. Therefore it is necessary to use some standard measure of the relative business level for purposes of comparison. The Federal Reserve Board Index of Industrial Production offers the basis for such a measure.l This Index, a weighted composite of 81 different series, rests upon the averages of the years 1935 to 1939 as 100, and is presented graphically in Fig. I. Even a cursory examination of the chart will indicate a definite uptrend for industrial production over a period of years. This uptrend is due to at least two factors: (I) an actual increase in national population, and (2) a probable increase in the per capita consumption of goods. This means that there is no such thing as a fixed Normal, rather Normal is a variable, tending to increase from year to year. In order to measure the amount of annual increase in normal, the Index of Industrial Production must be studied in relation to its major components, Durable Goods and Nondurable Goods, Durable Goods are those made from the lasting materials such as iron, steel, other metals, lumber, stone, cement, clay, glass. Nondurable Goods are those for early consumption, such as foods, textiles, tobacco, chemicals, paper, gasoline, and goods made of leather and rubber. The purchase of Durable Goods may be postponed, but Nondurable Goods must be purchased currently unless the standard of living is lowered. The Federal Reserve Indexes of durable and nondurable goods are shown graphically, 1920 to 1939, on Fig. a (pp. 764-765 of ref. I). It is apparent that fluctuations in the production of nondurable goods are not nearly so wide as in the production of durable goods, and that the curve of Industrial Production (Fig. I) would fall between the two curves on Fig. 2. It would, however, seem logical that both curves should follow the same long-term trend, or that over a period of two to three decades the relative proportion of durable and nondurable goods, in periods of normal production, should be the same. It is neces-

Jan 1, 1942

By M. G. Arthur

This paper is a theoretical analysis of fingering of water and coning of water and gas in homogeneous sand. Investigation of this idealized case illustrates the relative magnitude of the factors involved in actual conditions. The body of the report presents equations, example calculations, and charts that facilitate solution of such problems. Derivation of the equations introduced in this paper and a discussion of previously published equations are included in the appendix. Introduction Production of water from oil wells as a result of the pressure gradients established by flow of fluids through oil-~roducing sands is a common occurrence, which influences the cost of oil production, the degree of depletion and the efficiency of expulsion of oil from naturally occurring reservoirs. Control of water production and encroachment are important both in primary and secondary phases of of exploitation in order to produce oil and gas at lowest cost and in order to achieve the greatest ultimate recovery of the oil in the reservoir. Although many actual oil reservoirs present a multitude of variables that influence fingering and coning of water and gas, an inspection of the relationship and magnitude of the forces involved in the case of a homogeneous sand may indicate satisfactory methods of controlling water production. Application of equations relating the variables may indicate the geometric type of drainage that exists in a particular reservoir or in the vicinity of a particular well. A homogeneous sand body is assumed within the portion of the reservoir influenced by the well. Two geometric types of drainage are considered theoretically. The first is water fingering into an oil sand that is relatively thin compared with the lateral extent of the sand. This sand may represent the entire oil-producing reservoir or it may represent one interval in an oil reservoir, which is separated from other producing intervals by competent lithologic barriers to flow of fluids. For the condition of complete penetration of a well in such a sand body, it may be assumed that no flow occurs across bedding planes. A mathematical relation is developed between the limit of approach of a water finger to the well without being drawn into the well and the corresponding operating pressure drawdown. The second condition considered is that of water or gas entry into an oil well as the result of coning through bedding planes. The theory and graphical solution developed by Muskat' for the limit of approach of a water or gas cone to a well, without its entry into the well, related to the corresponding maximum pressure drawdown, is reviewed and amplified, Charts are presented, which facilitate graphical solution of the problem. A method is presented for the extension of this type of graphical solution to the case where gas and water coning occurs simultaneously~

Jan 1, 1944

By Parke A. Dickey

Potential differences between strata of shale and sandstone have been recognized for about 15 years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electro-¦ chemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are moditied in measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles. Introduction The existence of potential differences in the surface of the earth has been known for some time, and their measurement has facilitated the discovery of geological discontinuities such as ore bodies. The technique of measurement has been well established.1-3 In measurements in oil wells, it has been found that the potential of shales with respect to some arbitrary reference is very nearly constant in any one well, at least below the zone to which meteoric water has gained access. Sandstones and some other types of sedimentary rocks have a difference of potential with respect to shale that is negative arid may attain a value of 200 millivolts or more. The difference of potential, as usually measured commercially with water in the hole, is distributed over about one foot vertically at the top and bottom contacts of the sandstones. The sharpness of the curve at the formation contacts can be improved by using a short electrode that is close to the wall of the hole' These potentials generally have been ascribed to the disturbing effects of the water in the drill hole. Potentials have been found, however, in wells in which no water was present. In the course of experiments in electrical logging in pennsylvania, carried out by the pennsylvania Geological Survey, observations were made of several phenomena that hitherto have not been described, to the author's knowledge, ill the published literature. The potential differences across the contacts of sandstone and shale are called ill this paper "natural potentials," as distinguished from the potentials caused by electroendosmosis (electrofiltration) and concentration differences, which will be discussed subsequently. Potentials in Cored WeLl In the spring of 1942, the author measured the potentials in an exploratory well (Day 13, near Grand Valley, Pa.) which had been cored With diamond tools. The potentials were first measured with fresh water in the hole. * null balance potentiometer was used in this and all the other measurements described in this paper. One nonpolarizing porous pot electrode, containing copper sulphate solution and

Jan 1, 1946