Search Documents

By John S. Brown

As a part of a symposium on the relations of structure to ore deposition, in February 1938, the writer presented some tentative opinions derived from his experience with a number of important lead-zinc replacement deposits. These ideas were set forth, as a basis for discussion and a stimulus to further inquiry, in a mimeographed leaflet that read as follows Intimate acquaintance with a number of lead and zinc deposits in metamorphosed limestones seems to indicate the existence of certain common features from which can be established some general principles governing the localization of ore in this type of formation. It is suspected that these principles can be applied, with modifications, to mineralization in unmetamorphosed limestone. In metamorphosed formations, some observed rules are as follows: 1. Bands or masses of pure limestone are very resistant to replacement by ore solutions, and are likely either to contain no ore or to resist replacement until near the end of mineralization. The reason for this apparently is physical, not chemical, since microscopic data indicate that when ore is deposited by far the greater part of it substitutes for carbonate. The chief factor is believed to be a lack of porosity in massive limestone that has undergone flowage and recrystallization. 2. Masses of intensely siliceous or silicated rock are likewise unfavorable ore receptacles. This seems to be accounted for by two factors: (a) chemical unsuitability or resistance to replacement, and (b) physical resistance to small-scale brecciation, which might facilitate the opening of effective channelways for solutions. Some low-grade ore may occur, however, and also sporadic fracture fillings. 3. The optimum condition for ore reception appears to be found in bands or areas containing carbonate and silicates (or quartz) intimately mingled in something like equal proportions. In this situation movement is likely to result in mixed flowage and fracture, producing a fine-textured porosity that admits solutions freely and provides access to an abundance of replaceable carbonate. Cleavage cracks in some minerals such as diopside are believed to facilitate the penetration of solutions. 4. Certain minerals or assemblages are regarded as favorable impurities in a limestone and others as unfavorable. Original quartz, and subsequently developed diopside, and perhaps garnet, are typical favorable pre-ore gangue; in general rather equidimensional, brittle minerals. Tremolite, biotite, and probably wollastonite, are typical unfavorable pre-ore gangue; in general highly elongated and somewhat flexible minerals likely to develop under strong shearing stresses. 5. Tentative opinion is that the ratio of lime and magnesia in a limestone is of little or no importance.

Jan 1, 1940

Discussion of the paper of L. A. DELANO, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 129, September, 1917, pp. 1267 to 1286. L. A. DELANO.-Since this paper was written, our daily mill tonnage has increased, from 2100 tons to 2700 tons a clay. We now use 11,000 lb. of chrome-steel balls of 2 ½ -in. maximum diameter, for an average crushing capacity of 275 tons per 24 hr., this giving a much higher crushing efficiency. I wish to call attention to two typographical errors in my paper as published. On page 1271, Table 1, the screen analysis of ore at the Bonne Terre mill should be stated in inches instead of mesh. - On page 1272, "the rolls average 185 tons per 24 hr., and have shown by test that 250 tons per hour can be maintained" should, of course, read "250 tons per 24 hours." THE CHAIRMAN (0. M. BILHARZ, Miami, Okla.).-Is the increased mill capacity due to improvement in the re-crushing of middlings or to keeping middlings out of circulation and treating them separately? L. A. DELANO.-AS was shown in Mr. Rabling's paper (Bulletin No. 128, p. 1161) the tonnage was raised by about 400 tons by simply changing the arrangement of screen openings in the jig bed and using punched plate instead of woven-wire screen. Then, by adding a ball-mill, we are taking from the jigs a much larger tonnage of middlings than before or as much as the ball-mill will crush. By sending the ball-mill product to tables and flotation, the jig capacity for original ore is increased. CHAIRMAN BILHARZ.-In your opinion, the satisfactory operation of a Hancock jig on a given ore requires adjustment of the length of the different screens and careful selection of screen openings? L. A. DELANO.-I think it does. In order to decide what screen openings to use on the jigs, we did a great deal of experimental work, making screen analyses of the various hutch products, and then hand-sorting the galena, middlings and chat from each size screen to determine the percentage of galena in each. Then adjusting our jig screens, we gradually worked the process up to a very efficient basis. ERNEST GAYFORD, Salt Lake City, Utah.-I would like too ask Mr. Delano whether the work of the Allen cone has been quite as satisfactory as the manufacturers claim for it.

Jan 1, 1918

JESSE L. JONES,* Pittsburgh, Pa. (written discussion?).-As the die-casting process is so very different in character from the process of making sand molds, it is often considered that entirely different methods of pouring, gating, venting, etc. should be used. There is really, however, no essential difference in the making of (lie castings and sand castings, and similar methods should be used in each process. In the matter of gating, the metal should be introduced at a central point, as nearly as possible, so that it will have an equal distance to flow from the point of entrance to the most distant points of the mold. This will cause a uniform rate of congealing of the casting and prevent streaks and cold shuts. The venting should be done in such a way that a free exit of the air in the molds can occur. It should be less difficult to take care of the venting of a die-casting mold than to vent an ordinary sand mold. In the case of a sand mold, the venting is left, to a considerable extent, to the judgment of the molder, and it is possible that no two molds will be vented in a similar manner. Further than this, after a vent has been made in a sand mold, it may become clogged by the sand and for this reason be inefficient. There is also quite a variation in the pressure of the metal entering a sand mold, due to varying heights of the pouring gate. In a die-casting mold these factors can be controlled more closely. The vents should be so disposed that the air in the mold compressed by the entrance of the metal may be able to leave the mold at a uniform rate and by exits located symmetrically. These exits are made quite small on molds at first, as they can he easily enlarged if necessary, and they are tapered so that a free flow is guaranteed without danger of the metal spurting out from the die. Uniformity of pressure of the metal as it enters the mold is very important and, as the pressure is mechanically applied, its control is not difficult. It is true that a sand mold has much less of a chilling effect on the metal poured into it than has the die-casting mold, but, outside of this point, there is a great similarity between the die-casting process and the process of making castings in sand folds. It is suggested that much would be gained by regarding these two processes as not essentially different.

Jan 4, 1919

By G. Richards Gwinn

GRAPHITE is one of the so-called minor nonmetals that have become of major importance during the present conflict. Requirements of the domestic industry for graphite are relatively small and uses have changed so greatly in the past 25 years that different types, with few exceptions, are more nearly interchangeable in use. However, the quality of the graphite required for crucibles is exacting and under present manufacturing practices only a small part of the world production can be utilized economically by this industry. Graphite, for the domestic crucible industry, was supplied almost entirely by imports from Madagascar and Ceylon before the present war. The quantity required has been increased by the war and the greatest demand is for Madagascar flake. The fall of France to Germany in 1941 and the Japanese expansion southward threatened our supply of crucible-grade graphite, therefore the domestic industry was revived to supplement imports and to act as insurance in the event of complete stoppage of imports. Two plants were constructed for the Government, one at Ashland, Alabama, called the Crucible Flake Graphite Co., operated by Haile Mines, Inc., and one near West Chester, Pennsylvania, operated by the Benjamin Franklin Flake Graphite Co. Loans were made by the Reconstruction Finance Corporation to the Alabama Flake Graphite Co. at Ashland, the Ceylon Graphite Co., at Goodwater, Ala., and the Southwestern Graphite Co., at Burnet, Texas. However, by the end of 1943 the import situation had improved and it was no longer necessary to continue Government assistance to mine and stock-pile the high-cost domestic material. Graphite is found in virtually every country of the world. Most occurrences are of no economic importance because of their poor quality, prohibitive mining and milling costs, inaccessibility, and poor location with reference to the industrial centers where graphite is used. The principal commercial deposits are found in Ceylon, Madagascar, Chosen (Korea), United States, U. S. S. R., Canada, Germany, and Mexico. Graphite is a typical international mineral in that it is utilized mainly in countries noted for industrial activities, whereas the two islands, Ceylon and Madagascar, which produce the major part of the world's high-grade graphite, are virtually devoid of any manufacturing establishments requiring its use. The industry thus is violently disturbed by wars. TYPES of GRAPHITE USED IN CRUCIBLES Graphite of various kinds and from many countries has been used for making crucibles. Passau (Bohemian) flake was first used in Europe, but by the middle of the seventeenth century crucible formulas were established largely on Ceylon graphite and German Klingenberg clay. Ceylon graphite is granular and the grains are subdivided into more or less

Jan 1, 1945

Discussion of the paper of CHARLES H. MACDOWELL, presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 103 to 114. GEORGE S. RICE, Pittsburgh, Pa.-I am especially interested in the mining side of this important question. In 1911, when in Europe investigating mining matters, giving special attention to subsidence clue to mining, for there is a very big problem of that kind, as many of you know, in the Pennsylvania anthracite region, I visited Stassfurt, which is one of the chief centers of potash mining, and which was pointed out as the place to see surface subsidence. We found the town much askewsome of the streets having sunk from 15 to 30 ft., leaving many ancient buildings pitching at various angles. One old church, 500 or 600 years old, has been sunk about 20 ft., cracking it badly. I understand that this condition came about because in early mining clays they were careless about leaving proper supports and used no filling or packing. The Stassfurt mines work along a buried anticline the sides of which pitch at 45° on the average. Through this careless mining they had a break of the hanging wall which let in water from the overlying marls and sands. The water rapidly dissolved the salts in the pillars, and spreading through the entire chain of mines, caused their complete loss, with serious trouble for the old city. They had to start new mines some distance away, and take care to prevent roof caves. The packing system is of interest. They were driving large rooms into the rock-salt foot wall and using the rock salt as dry filling. The application of hydraulic filling, using a saturated solution, was under contemplation at some plant nearby. Whether 6r not the plan was carried out I do not know. I was reminded of the plan by Mr. MacDowell's remarking on the use of a saturated salt solution in the core drilling. His reference to the apparent breakdown of the potash syndicate raises an interesting question. We have had the German system of syndicates pointed out as perhaps one means of solving our troubles in the soft-coal mining industry due to overproduction. It seems to have worked out admirably in the case of the Westphalian coal-mining syndicate and also in the syndicate of Upper Silesia; but apparently the syndicate plan did not work in the potash industry. .

Jan 5, 1915

By Kendall E. Born

Production of crude oil in Tennessee during 1941 was slightly more than 15,000 bbl., about the same as in the preceding year. Two thirds of the total was from the Mississippi limestone pools in Scott and Morgan Counties. About a dozen small scattered wells in Clay, Pickett, and Fentress Counties, pumped irregularly, produced approximately 5000 bbl. Natural gas was marketed from wells in Morgan and Fentress Counties for consumption in the Sunbright and Jamestown areas, respectively. The production by counties is shown in Table I. Drilling activities in the state fell to the lowest stage since 1933. Twenty-seven wells were spudded in during 1941, of which six were drilling or only temporarily suspended on Dec. 37, 1941. Of the 22 completions, four were gas wells of undetermined quantity, but are classed as commercial, and 17 were dry or near-dry holes. One well encountered oil, but it has not been tested. The total footage drilled during the year was 29,916 ft.; the average depth of wells was 1359 ft. The more important wildcats are listed in Table 2; the distribution of tests according to physiographic divisions is given in Table 3. East Tennessee.—One well was drilled to 3480 ft. in northwestern Anderson County, in the highly disturbed Appalachian area, a region long considered the most unfavorable in the state for the accumulation of oil and gas. Another test is now drilling below 2000 ft. in this general area. Cumberland Plateau.—There were two completions in the Cumberland Plateau area. One test, drilled in northwestern Scott County in an area of former Mississippi limestone production,' encountered a considerable amount of free oil at 850 ft., about the same horizon as in the old abandoned wells. No pumping tests have been made to date. A well at Oneida, Scott County, found gas at 1579 ft. in a sandy limestone of lower Mississippian age. The volume was reported doubled by a shot, although no open-flow measurement is available. Eastern Highland Rim.—Six completions on the eastern Highland Rim resulted in two small gas wells in Fentress County, which will be used to augment the supply for Jamestown. The producing horizons are shaly limestones of Ordovician (Trenton) age. Two wells in this area tested the upper part of the Knox dolomite group, one of which encountered some free oil in a sandy dolomite at 1670 to 1681 ft. A test high on a well-defined structure in Clay County found a considerable amount

Jan 1, 1942

By T. Sterry Hunt

AT the meeting of the Institute in Easton, October, 1873, I made a communication on the Ore Knob copper mine, in Ashe County, North Carolina (Transactions, vol. ii, p. 123), in which I called attention to the chemical decomposition alike of the pyritous lode and the inclosing gneiss rock to a depth of 60 feet, by which the feldspar of the latter had been converted into clay, and the whole rock very much softened. Such a decomposition is well known to be almost universal in the crystalline rocks of the Appalachians south of the Potomac ; and if it is only seen in rare and exceptional cases farther to the northward, this, as I have elsewhere pointed out, is due to the fact that the decomposition began and ended in the ages anterior to the drift period, and that the decayed portions which still remained were at that time removed from the surface, except in some localities which were protected from the eroding agency. I have lately had an opportunity of studying a remarkable instance of this kind in an examination made last month for the corporators of the Hoosac Tunnel.* The locality is at the western base of Hoosac Mountain, the western slope of which rises rapidly 1300 feet above the town of North Adams, in Berkshire County, Massachusetts, itself 700 feet above the sea level. Through this mountain, as is well known, a tunnel for the Troy and Boston Railroad has lately been opened, a distance of 25,081 feet from east to west. The rock of the mountain consists of mica schist and micaceous gneiss, including in its western half a great mass of harder feldspathic and quartzose strata in part a granitoid gneiss, the strata for the most part dipping to the eastward with variable angles, but with occasional western dips, apparently due to inversion. The crystalline strata of the mountain crest and sides are in many places exposed, and present rounded surfaces, often deeply grooved and striated, but with no appearance of decay. At the western base of the mountain, however, the gneissic rock is in a state of complete decomposition, which was well displayed in opening the tunnel, which, for a distance of several hundred feet, was driven through highly inclined strata so much decomposed that they were excavated with pick and shovel, and without the aid of blast- * See, for a detailed account of this examination, Dr. Hunt's report, published by the General Court of Massachusetts in House Document No. 9, 1875.

Jan 1, 1875

By Harvey S. Mudd

AMONG the highly skilled craftsmen of the Renaissance were those who worked with ores and metals. The author of this book, Vannoccio Biringuccio, was a master craftsman in the practices of smelting and of metalworking. Contrary to the customs of a trade, Biringuccio was moved to impart his knowledge to all and thus he has given us the earliest hand- book on metallurgy-in fact, the first printed book dealing with the applied metal arts and the processes of ore reduction. We should remind ourselves that metallurgy is an ancient art and then it fair1y may be said that Biringuccio sought to describe the techniques that had been in course of development since the Bronze Age of western civilization. Whether Biringuccio was a man of learning or a scholar according to the standards of his time we do not know, but today we recognize him as a man of science who gave his wisdom to succeeding generations. It was not until the coming of the Power Age at the end of the eighteenth century that progress was resumed in the science of which he wrote more than two hundred years before. Little is known of Biringuccio's training in his native Siena. It can be surmised that there, as in Florence, where his contemporary Benvenuto Cellini lived, he received his training in the craftsman shops where the industrial arts were taught and flourished alongside the fine arts. Perhaps he and Cellini were acquainted, although there is no mention of Biringuccio in Cellini's autobiography-an omission that Cellini's vast egotism makes understandable. He was the great artist, and Biringuccio was a practical, studious, unromantic figure with no favors to dispense. In the April 1940 issue of Mining and Metallurgy Dr. Smith describes Biringuccio's book under the title of "A Neglected Italian Metallurgical Classic." The article, revised and extended, forms the basis of the introduction to the present volume, and I urge all who take up Pirotechnia to read what Dr. Smith has written in the Introduction. Biringuccio's work is a classic and in its translation Dr. Smith and Dr. Gnudi have brought to bear the high degree of scholarship that it deserves. Dr. Gnudi made the translation at Dr. Smith's request and it was then refined "in the fire" of his scientific knowledge of the subject. The result is a book which the Institute is proud to place before its members and which the Memorial Fund Committee considers it a privilege to publish.

Jan 1, 1942

By George M. Straughan, Coleman D. Hunter

Oil and gas development as well as extensive leasing in Kentucky during 1940 has shown a marked improvement over the past three years.$ The most noticeable improvement is the gas development in eastern Kentucky and the deep tests being drilled by major oil interests. In western Kentucky, 406 wells were drilled, of which 173 were oil producers, 12 were gas wells and 221 were dry or abandoned. The number of dry tests was large, because no important, new oil or gas pool was discovered and many of the dry holes could be considered wildcat tests. However, with either oil or gas possibilities from Pennsylvanian formations on through Mississippian, Silurian, Devonian, and Ordovician, this percentage of dry holes seems rather high. Many of the dry tests possibly should have been tested in deeper horizons before being abandoned: namely, Silurian and Ordovician ages. In eastern Kentucky, 213 wells were drilled, of which 113 were gas producers, 61 were oil wells, and 39 were dry holes. Of these wells, 117 were drilled in the most important Big Sandy gas field, in Floyd, Pike, Knott and Martin Counties, and of this number 103 were gas producers, 5 were oil wells, and 9 were dry holes. In the Big Sinking oil field of Estill, Lee and Powell Counties, 70 of the remaining 96 wells were drilled, j6 being oil producers. During 1940, four deep tests were drilled in eastern Kentucky. One test penetrated the Knox dolomite in Knox County and was dry; no St. Peter sand was encountered. Another test in Lee County had some gas in what might be called St. Peter sand, according to the State Department, and also some gas deeper in the Knox dolomite. In Wolfe County, a small oil well was completed in the Ordovician, which was undoubtedly of Trenton age. ilt the present time, four deep tests are being drilled, all of which will go to the Knox dolomite. In Elliott County, on the Burke dome, the Inland Gas Co, is drilling at 3650 ft. In Magoffin County, on the Paint Creek uplift, the Cumberland Petroleum Co. is drilling at 3800 ft. In Clark County, in the Ruckerville fault area, W. 0. Allen is drilling at 1800 ft. In Laurel County, on the Sinking Creek dome, the Globe Oil and Gas Co. is drilling at I750 ft. If production is encountered in the Trenton, St. Peter, or Knox dolomite in any of these tests, eastern Kentucky will experience a marked increase in deep development.

Jan 1, 1941

By J. B. Newsom

During July and August, 1931, the Bloomington Limestone Co., at Bloomington, Ind., ran a single wire saw on ledge No. 2 at Maple Hill quarry. The ledge was hard rock, much harder than the average Indiana limestone. It was opened at two ends for a depth of about 20 ft., leaving a 130-ft. section between. During the tests 21 cuts were made in this ledge, to an average depth of 10.42 ft., for a total effective cutting area of 28,445 sq. ft. The actual area sawed was about 20 per cent higher, as we did not level down in the center, preferring to cut deeper on the ends. The various cuts were carefully logged, and the results plotted. A study of these results is interesting, as it enables a forecast of probable future costs to be made, and also because it points out the limitations of wire saws, and the lines development should logically take. Some of the inferences to be drawn are discussed below. Best Length of Cut.—No trouble was due to length of cut, except that we could not easily level down a long cut, and it is probable that longer cuts, say up to 200 ft., can be made. Obviously, longer cuts will result in a higher sawing rate in square feet per hour if they do not cause stoppages. Working Higher Ledges.—The cuts averaged 10.42 ft. high by 130 ft. long. A study of several logs indicated that during only about 15 per cent of the cutting time was the saw cutting to its full efficiency; that is, during about 85 per cent of the time the saw was bedding in at the ends and not cutting well in the center, or the ends were below the floor line and only part of the wire was doing effective cutting. This does not mean that the wire was cutting to only 15 per cent of its capacity, but it means that during about 85 per cent of the time part of the cutting was being wasted. If higher ledges had been worked, the wire would have cut to its full efficiency a large part of the time, as it would have had a greater distance to saw after it had bedded in to the ledge before the ends went down below the floor level. The exact saving to be expected cannot be calculated, but it would be large if really high cuts were made.

Jan 1, 1932

By Andrew Allen

WHEN a mine is changed from hand, to me-chanical loading, the character of the coal dumped at the tipple is changed in many ways. Selective mining is not so easy with mechanical load-ers, and where much picking is done at the face it is apt to be wasteful anyway. Much recoverable coal is apt to be lost by too free gobbing and, in my opinion, picking at the face should be confined to removal of heavy rock, such as pieces of roof or bottom or sulfur balls. and to such clearly defined and persistent bands as can be readily recognized and segregated. With mechanical loaders of the shovel type, even this amount of gobbing is almost impossible. When coal is shoveled into a conveyor there should be no difficulty in doing as much picking as now by hand loading. The size of lumps may be greatly increased, on ac-count of the ease of handling them with a shovel, as the miners will not break them up in order to lift them into cars. Fines may be increased. This is, of course, not universally true, yet it is my opinion that a shovel breaks the coal more, as a rule, than hand loading. This might not be true with all types of shovels and is cer-tainly not true with a conveyor, either with or without the "duck-bill." The average car load will be greatly reduced in fields such as Illinois and Indiana, in which it is the practice to build up the coal above the sides. Where "level full" regulations prevail there should be no material change. When the coal comes to the tipple these differences usually result in the discovery, that many changes are necessary in the preparation plant. The increase in the percentage of fine sizes will probably not bother the screen, but may overload the conveying apparatus. The larger size lump may clog the chute, but as a rule the efficiency of the sizing screens is not greatly affected. In one completely mechanized mine the proportions of 6-in. lump and 2-in. screenings, when loading by hand, were 16.9 and 51.3 per cent respectively. When loading mechanically, these proportions changed to 15 per cent lump and 53.5 per cent screenings. The picking force on the tipple has been increased from 14 on hand loading to 33 men on mechanically-loaded coal. This is for an output of about 5000 tons.

Jan 4, 1927

By Howard I. Smith

The mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. IIO W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3 NaHCo3.2H2O). Pure trona con-tains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. Analyses Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally Pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nighten-gale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO 3.2 CaCO3), which he named shortite,² after Maxwell N. Short." He analyzed the samples of trona, with the results shown in Table I. In addition to the 10 ft. 1 in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either i mostly trona or some other soluble salt, but it should not be included in calculating | reserves. In the part of the core between i 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically I to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. Accompanying Minerals Fahey later secured about 600 ft, of the core for a detailed examination and study

Jan 1, 1942

By Howard I. Smith

The mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. IIO W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3 NaHCo3.2H2O). Pure trona con-tains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. Analyses Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally Pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nighten-gale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO 3.2 CaCO3), which he named shortite,² after Maxwell N. Short." He analyzed the samples of trona, with the results shown in Table I. In addition to the 10 ft. 1 in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either i mostly trona or some other soluble salt, but it should not be included in calculating | reserves. In the part of the core between i 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically I to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. Accompanying Minerals Fahey later secured about 600 ft, of the core for a detailed examination and study

Jan 1, 1942

By J. B. Newsom

DURING July and August, 1931, the Bloomington Limestone Co.,. at Bloomington, Ind., ran a single wire saw on ledge No. 2 at Maple Hill quarry. The ledge was hard rock, much harder than the average Indiana limestone. It was opened at two ends for a depth of about 20 ft., leaving a 130-ft. section between. During the tests 21 cuts were made in this ledge, to an average depth of 10.42 ft., for a total effective cutting area 028,445 sq. ft. The actual area sawed was about 20 per cent higher, as we did not level down in the center, preferring to cut deeper on the ends. The various cuts were carefully, logged, and the results plotted. A study of these results is interesting, as it enables a forecast of probable future costs to be made, and also because it points out the limitations of wire saws, and the lines development should logically take. Some of the inferences to be drawn are discussed below. Best Length of Cut.-No. trouble was due to length of cut, except that we could not easily level down a long cut, and it is probable that longer cuts, say up to 200 f t., can be made. Obviously, longer cuts will result in a higher sawing rate, in square feet per hour if- they do not cause stoppages. Working Higher Ledges.-The cuts averaged 10.42 ft. high by 130 ft. long. A study of several logs indicated that during only about 15 per cent of the cutting time was the saw cutting to its full efficiency; that is, during about 85 per cent of the time the saw was bedding in at the ends and not cutting well in the center, or the ends were below the floor line and only part of the wire was doing effective cutting. This does not mean that the wire was cutting to only 15 per cent of its capacity, but it means that during about 85 per cent of the time part of the cutting was being wasted. If higher ledges had been worked, the wire would have cut to its full efficiency a large part of the time, as it would have had a greater distance; to saw after it had bedded in to the ledge before the ends went down below the floor level. The exact saving to be expected cannot be calcu-lated, but it would be large, if really high cuts were made.

Jan 1, 1932

By Howard I. Smith

THE mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. 11o W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3.NaHCO3.2H2O). Pure trona contains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. ANALYSES Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells† and found to be exceptionally pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nightengale‡ for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO3.2CaCO3), which he named shortite,2 after Maxwell N. Short.* He analyzed the samples of trona, with the results shown in Table i. [ ] In addition to the 10 ft. I in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either mostly trona or some other soluble salt, but it should not be included in calculating reserves. In the part of the core between 1590 ft. 3 in. and 1600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. ACCOMPANYING MINERALS Fahey later secured about 600 ft. of the core for a detailed examination and study

Jan 1, 1942

By Howard I. Smith

THE mineral trona was discovered on Government land in 1938, about 18 miles west of the town of Green River, Wyo., in the core of the John Hay, Jr., well, a test well drilled for oil by the Mountain Fuel Supply Co. in sec. 2, T. 18 N., R. 110 W., sixth principal meridian. Although no oil or gas was reported, the drilling led to a discovery of great potential economic importance and exceptional scientific interest. Trona is a relatively rare mineral found at various places in playa deposits but not previously found at any great depth. It is composed of hydrous sodium carbonate and sodium bicarbonate (Na2CO3.NaHCO3.2H20). Pure trona contains the equivalent of 70.35 per cent of sodium carbonate. Total sodium computed to carbonate times 1.42 equals the percentage of trona in the absence of other sodium carbonate minerals in the sample. ANALYSES Two short pieces of core sent to the author a few days after the completion of the Hay well were analyzed by R. C. Wells[t] and found to be exceptionally pure trona. A brief article on this discovery has already been published.1 Arrangements were then made through W. T. Nightengale[$] for the author to inspect and sample the core. The company log of the well included notations of sodium salt crystals from a depth of 1190 to 1820 ft. Not being able to identify all the minerals present, the author selected several specimens of the core for petrographic examinations and sampled the sections of trona for analysis. J. J. Fahey, of the Geological Survey, examined the specimens and reported most of the crystals to be a new anhydrous sodium carbonate and calcium carbonate mineral (Na2CO3.2CaCO3), which he named shortite,2 after Maxwell N. Short.* He analyzed the samples of trona, with the results shown in Table I. [ ] In addition to the 10 ft. I in. of trona in the first section, it is reasonable to assume that the 9 ft. 8 in. for which no core was available for sampling is either mostly trona or some other soluble salt, but it should not be included in calculating reserves. In the part of the core between 1590 ft. 3 in. and I600 ft. 4 in. the material insoluble in cold water, amounting to about 5 per cent, was estimated petrographically to contain 70 per cent clay, 25 per cent shortite, and 5 per cent pyrite. ACCOMPANYING MINERALS Fahey later secured about 600 ft. of the core for a detailed examination and study

Jan 1, 1942

By Ernest G. Enck

"The Rockets' Red Glare" of the Fourth of July is produced by strontium compounds. However, strontium has a number of less spectacular uses; i.e. in, or in connection with, the manufacture of ceramics, caustic soda, glass, railway and truck signal flares, beet sugar and steel. The principal ore of strontium for use both as the mineral and for production of compounds is celestite (SrSO4). This mineral varies in color from white to pink or blue depending on presence of impurities. It has a hardness of about 3.5 and specific gravity of 3.9. It is brittle and has perfect basal and prismatic cleavages. The high grade ore is obtained from England, hence it has become the standard for all other producing areas. (See analyses, Table 1.) The most objectionable impurity in English celestite is iron, coming mostly from adhering clay. On the other hand, Mexican celestite, while no higher in strontium sulfate content, is extremely low in iron (less than 0.2 pct), hence it is more desirable for certain uses. Most of the celestite in Spain and in the United States is high in calcium and barium, and commonly high in iron, and requires some form of beneficiation in order to be equal to English ore. The natural carbonate (SrCO3), or strontianite, is less important than celestite as a source of strontium, because it is less abundant and is not so widespread in its occurrence. Furthermore, it generally occurs with calcite (CaCO3) and lead sulfide (PbS), and for most uses these impurities are detrimental. This mineral is generally white or yellowish, forming needle-like crystals. It has a hardness of about 3.7 and a specific gravity of 3.68-3.8. The mineral is brittle and has an imperfect cleavage. A typical analysis of German strontianite is shown in Table 1. [ ] Distribution of Deposits UNITED STATES Occurrences of strontium minerals are known in Arkansas, Arizona, California, Illinois, Ohio, Pennsylvania, Tennessee, Texas, and Washington. Celestite occurs in the Vulture Mountains, Maricopa County, Arizona in beds three to ten feet thick associated with sandstone, gypsum, and barite. Because of the low strontium content, approximately 86 pct SrSO4, it has no commercial value. A large deposit of celestite occurs in San Bernardino County, California, in the Cady Mountains near Argus Station, about eight miles west of Ludlow. The celestite here is interbedded with shaly and clayey tuff in a zone about 300 ft thick. Massive, finely crystalline ore has been recovered with an analysis

Jan 1, 1960

By Walter Lang

The year 1931 has shown a marked change over 1930 in New Mexico, with respect to the volume of activities attendant upon the petroleum industry. Although the total production of oil and gas this year exceeds that of preceding years, the results have been attained from established units operating under restriction, but capable of supplying far more than the economic conditions justify. The presidential order of March 12, 1929, that "there will be complete conservation of Government oil in this administration," has merely anticipated a normal consequence of overdevelopment. As a result of the combined economic and legal restrictions imposed, very little new drilling has occurred during the year. Even in proven areas the drilling of offsets has been curtailed to the absolute limit of requirements. Scouting and sample-cutting, which in 1930 were still in a state of feverish activity, are at low ebb, and lease buying has reached a condition of stagnation. A number of the major oil companies have either materially reduced their field and office forces or completely eliminated local office representation. Two tests of particular interest, because correlation shows them to be structurally high although they failed to produce, are the National Securities well drilled six miles west of the town of Hobbs, on sec. 33, T.18 S., R.37 E., Lea County, to a total depth of 4272 ft., which developed a flow of 4,000,000 cu. ft. of gas at 3860 ft., and a show of oil; and the Western Drilling Co. No. 1 State, sec. 16, T.20S., R.32 E., Lea County. The latter test found dead oil at 2575 to 2580 ft., and sulfur water at 2745 ft., increasing to 2780 ft., representing the zone from which production was generally expected. The well was drilled to 4013 feet. The discovery of sulfur at about 950 ft. in the deepening of an old water well (Pearson, NE. 1/4 sec. 8, T.16 S., R.25 E.) drilled in the Little Cottonwood area northwest of Artesia led the Union Sulphur Co. to drill three prospect tests on a block of acreage in the vicinity during the summer and fall. The results of the investigation have not been disclosed. The Kummbaca Oil and Gas Co. drilled the T. J. Kerline No. 1, in sec. 34, T.21 N., R.30 E., Harding County, gaging 3,654,000 cu. ft. of 98 per cent CO² at 940 ft. The Barton structure, 20 miles east of Albu-

Jan 1, 1932

By W. P. Blake

Forging under the hydraulic press, which was introduced by Haswell in the year 1861, at the machine shops of the Imperial State Railway Company of Austria, has since been greatly improved, so that at the present time there are very few parts of machines which cannot be produced in this way, and at no greater cost than iron castings. The process is now used at Vienna chiefly for such parts of locomotives as cross-heads, link-bars, axle-box frames, etc., especially where the form is intricate, and there are many angles and projections. These objects weigh from 50 to 150 lb. or more, and it is claimed for them that they are not only much cheaper than ordinary forgings, but are much more regular in form and stronger. The results which Mr. Haswell has attained, after years of patient experimenting, were well shown in the Austrian Department of the Vienna Exhibition by a collection of the pressed objects in iron and steel, just as they left the moulds, with some of them cut asunder longitudinally and the surfaces etched, so as to show the internal structure or direction of the grain. Through the courtesy of Mr. Haswell and his son I saw the hydraulic presses in full operation at the works, drawing down large Bessemer ingots, cutting them up into blocks of convenient size, and forming various park of locomotives. They have two large hydraulic presses in use; the largest, with a piston 24 inches diameter, gives 1200 tons pressure, and the second, with an 18-inch piston, gives 600 tons pressure. The pressure in the pumps is 600 atmospheres. The action is vertical; the piston descends upon the work, and for forging ingots is armed with a hammer-like head. An ingot of No. 7 soft Bessemer steel, which was forged in my presence, weighed 2030 lbs. One end being placed upon the anvil, the piston is brought slowly down and crowded into the mass as if it were putty or dough, forcing it each way, but chiefly in the direction of the length of the ingot, this being the narrowest section of the anvil and hammer. The piston is then raised and the ingot is moved forward for a second squeeze, and so on, until the first half of the ingot has been reduced in thickness, when it is turned on edge and the operation is repeated. The ingot is then turned end for end and forged until the whole length has been re-

By Willard P. Ward

I DESIRE to put on record a fact in relation to the effect of manganese on pig iron which I have never seen in print, and which may, perhaps, not have been observed by anyone except myself. In 1875, while experimenting on the production of ferromanganese in a blast furnace, I had burdened the furnace with a charge which I calculated would produce a 15-per cent spiegel. The furnace was very hot, having been running for a couple of days on a very light burden, and making a burnt iron, preparatory to the experiment I proposed to make to produce a high grade of spiegel. I calculated that the charge would begin to work in the furnace in about twelve hours after it was put on. After the lapse of that time I commenced to watch the furnace carefully, but found little or no. change in the appearance of the metal, although there was a very decided change in the cinder, showing that the manganese ore had come in work. The iron was quite gray and very tough. The character of the cinder was good for a spiegel cinder, and I could not imagine where the manganese was going to, as it (lid not appear to be in either metal or cinder in anything like the quantity indicated by the charge. The next morning things were still in, the same condition. The furnace was very hot, the cinder good, and the iron very gray. I was then sorely puzzled. I had never heard of a gray iron with over 4 or 5 per cent, of manganese, and had no notion that an iron with more manganese could be gray and tough. With great difficulty a piece for chemical test was broken from a pig. Not less than a hundred blows from a heavy sledge were required to break it off I took the specimen to the shop and directed that some borings from it should be brought to the laboratory, as soon as possible, whither I myself at once repaired -to put things in readiness for a rapid manganese determination. In about half an hour the machinist came in with the iron specimen in one hand and about, a dozen blunted and broken steel drills in the other, saying that it was impossible to drill the iron. There were several little depressions in the iron, which was malleable enough to be indented by the point of the drill, but not a chip had been cut from it. The metal was never subjected to further physical tests. A chip broken from

Jan 1, 1882