Search Documents

By C. H. Jr. Herty

FEW subjects have attracted the attention of metallurgists more than ,oxygen in steel. From the days of Mushet and Ledebur interest in this subject has been increasing, and as additional knowledge has become available, the problem has naturally grown more complex. Instead of using the simple term "oxygen" we now distinguish between iron oxide, silicates of various kinds, oxysulfides, oxygen as gas and oxygen in solid solution in steel. There are five general methods for determining oxides in steel: hydrogen reduction;, vacuum fusion; various wet-extraction methods, including electrolytic methods; methods depending on volatilization of the iron away from the oxides; and metallographic methods. For oxygen in solid steel each of these methods has both advantages and disadvantages. The hydrogen-reduction method is of no use on steels above about 0.20 per cent. carbon;1 furthermore, it gives only FeO and possibly some MnO. The vacuum-fusion method2 is expensive and gives total oxygen, with the exception of some A1203, and does not differentiate between the various oxides in which the oxygen exists. Most of the wet-extraction methods' give only the more insoluble oxides Si02 and A1203, though the iodine method gives MnO to an uncertain degree (information that may be more misleading then no information

Jan 1, 1930

By A. H. Dierker

Next to the metal itself, molding sand is the most important raw material used in the manufacture of steel castings. There are no accurate figures available but probably it would be safe to say that the average steel foundry uses approximately 1000 lb. of new molding sand per ton of castings produced. With untreated sands costing from two to four dollars (in some extreme cases it may run as high as eight or ten dollars) per ton delivered at the foundry siding, molding sand is an important item in the cost of making castings, and any information that may help to reduce this sand consumption should be of interest to the industry. Fundamental Considerations In a general way, molding sand in the average steel foundry passes through the cycle shown in Fig. 1. This diagram indicates that if all of the sand could be returned from the shakeout floor to the mixer no new sand would be required from the stock pile and molding costs would be reduced accordingly. Unfortunately, for reasons to be discussed later, it has heretofore been necessary to dilute the used sand constantly with new raw sand in order to maintain the properties that are essential to the production of satisfactory molds.

Jan 1, 1930

By James E. York

The honor so fairly earned and so incompletely and tardily paid to Henry Cort, the inventor of the puddling-furnace and the rolling-mill, has been fully set forth by Mr. Charles H. Morgan,' and needs no further emphasis here. In view of the importance of the rolling-mill in the treat ment of iron and steel, the paucity of information concerning it is surprising. With the exception of a book, written about 35 years ago, by Peter Ritter von Tunner, an Honorary Member of this Institute, and of desultory articles on simple sections, which have appeared in technical journals, I know of no publication attempting to treat this subject, although volumes have been written on the scientific theory and technical manipulations involved in other branches of the iron- and steel-industry. This strange anomaly may be due to the fact that roll-turning cannot be called a scientific business. It does not ordinarily come within the range of an educated engineer; yet it cannot be performed by an ordinary mechanic. It demands some of the qualifications of an engineer, in designing, and those of a mechanic, in execution. The men who have followeci this trade have controlled the training of their successors. In many cases the technical knowledge required has

Jan 1, 1907

By Harold B. Goldman, Don Reining

The sand and gravel industry is the largest nonfuel mineral industry in the nation (Drake, 1972), Table 1. In 1970, the production of sand and gravel totaled 944 million tons valued at $1.1 billion. California, which leads the nation with more than 140 million tons, together with Michigan, Ohio, Minnesota, Illinois, Wisconsin, and New York, account for 43 % of the total production in the nation. In commercial usage, "sand" applies to rock or mineral fragments ranging in size from particles retained on a No. 200 sieve (0.074 mm openings) to those passing a No, 4 sieve (4.76 mm openings). "Gravel" consists of rock or mineral fragments larger than 4.76 mm, ranging up to 3%-in. maximum size. The construction industry consumes 96% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see the chapter on "Silica and Silicon"). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material which is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster.

Jan 1, 1975

By William M. Brewer

History.—The history of gold-mining in Georgia and Alabama antedates the discovery of gold in California. A very large proportion of the gold used in the United States previous to 1849 was produced by these States. A great deal of this history is merely tradition, and no reliable statistics can be obtained ; yet a personal examination of the gold-fields of Georgia and Alabama indicates that tradition is as fairly reliable, with regard to the history of these gold-regions, as it is in any similar cases throughout the world. In Georgia, the history of gold-mining dates back to 1829, when the first gold-mining excitement in the United States occurred. In Alabama, the discovery of gold was made some years later through the work of prospectors, incited by the rich finds in the Georgia mining camps. The greatest product of gold in these States was between the years 1840 and 1849. In Lumpkin county, Ga., and Cleburne county, Ala., the districts from which the most of this gold was taken, the tailing-dumps are silent witnesses of the extensive operations which were carried on by the primitive and crude methods then known. It is no rare thing to see trees 12 to 15 inches in diameter, and even

Jan 1, 1896

Discussion of the paper of J. E. Johnson, Jr., The Effect of High Carbon on the Quality of Charcoal-Iron, presented at the Cleveland meeting, October, 1912, and printed in Bulletin. No. 74, February, 1913, pp. 173 to °14, and of the paper of Albert Sauveur, Notes on Cast-Iron, presented at the New York meeting, February, 1013, and printed in Bulletin No. 75, March, 1913, pp. 503 to 524. CHAIRMAN. JOHN BIRKINBINE :-Just 20 years ago I had the pleasure, when I retired from the Presidency of the Institute, of introducing my successor, and this afternoon it is my pleasure to ask my good friend Dr. Howe to open this discussion. PROFESSOR HENRY M. HOWE, New York, N. Y. :-This paper of Mr. Sauveur's is extremely interesting. It is one of those papers that one wishes to read in the quiet of one's study, where it can be read with great profit. There are many points which he makes which I think are of very great value, in particular as to the importance of getting fine ;grained graphite by a relatively rapid cooling, combined with a high percentage of silicon. That theory would seem to be very promising; how far it has actually been carried out very likely Dr. Moldenke can. tell us.

Jan 5, 1913

By C. A. Heiland

THE investigations described were made on a portion of Clear Creek basin near Golden, Colo. (A portion of the area under survey is shown in Fig. 1. The photograph was taken in the vicinity of station No. 2 of Line II.) Three principal purposes were in the minds of the investigators: 1. To repeat with modern, more sensitive and more reliable instruments magnetometric placer investigations previously made. 2. To disprove the recently advanced theory that deposits of the glacial period have no pronounced magnetic effects. 3. To develop in detail the theory of the magnetic effects produced by placer deposits. Six years ago, the first magnetic observations were published, which proved that it is possible to locate gold-bearing channels with relatively crude instruments.1 Two years ago, K. C. Laylander published results obtained with similar instruments.2 The measurements of the latter were discussed by the senior author of this paper.3 At that time, however, the material available for such a discussion was somewhat scarce and not made with the most modern magnetic instruments, although very brilliant results were obtained. Therefore, the senior author felt that magnetic investigations should be made on very clear geologic conditions with the most modern instruments.

Jan 1, 1928

By Rossiter TV. RAYMOND, Charles H. Snow, THEODORE DWIGHT

SECRETARY'S NOTE.-The complete list of all officers of the Institute will be found on p. iv. of this number of the Bulletin. The following explanation may recall to old members, and convey to new ones, the relations of the two governing bodies, as determined by the, Certificate of Incorporation of the Institute, and the Constitution and By-Laws adopted in accordance therewith. The body legally responsible for the business management is the Board of nine Directors (three elected annually to serve three years), which elects its own officers. This body, for reasons of practical convenience, is composed of well-known members, residing in New York City, and able to attend, without serious inconvenience or expense, the necessary meetings of the Board. The officers of this Board are legally the officers of the Institute. But, apart from business manage-ment, the Board exercises no control over the election of members, or the professional and technical work of the Institute, except that its vote is required to elect honorary members, upon the recommendation of the Council. The Council is a. body, constituted in all respects (except that it has no Treasurer) like the Council existing before the incorporation of the Institute, in January, 1905, and charged with all duties and powers, except those which the Board of Directors must legally perform. It elects members, appoints the times and places of professional meetings, and controls the publication and distribution of papers and volumes, etc. Its members (President, Vice-Presidents and Councilors) are elected by the members of the Institute, voting in person or by proxy, and after publication of the nominations received ; and it is intended to repre¬sent, as far as practicable, both the professional and the geographical distribution of the membership. Consequently, whatever professional honor attaches to official position belongs to membership in the Council, rather than in the legal Board of Directors. This remark implies no disparagement of the members of the latter body, every one of whom has served, or is now serving, as a member of the Council. But it is only fair to explain that their election and continued re-election as Directors is simply a matter of legal convenience.

Mar 1, 1906

By O. H. Hahn

I have lately had occasion to conduct a campaign at the works of the Empire City Company, in Railroad District, Elko County, Nevada, which, if not highly satisfactory, was at least very interesting in a technical point of view, and which I therefore think worthy of communication to the Institute. The lead ores in this district occur in lenticular masses along and near the contact of crystalline limestone with a dioritic porphyry, and consist of argentiferous carbonate of lead and galena, the latter occurring in solid blocks, or in ribbons running through the limestone. Associated with these are silicate, carbonate, and suboxide of copper, and brown and calc-spar. Adding to this, that the proportion of galena in the ore is small, and that no iron pyrites exists in the district, it is at once evident that the ore-mixture is difficult to treat. For a successful reduction by smelting, it would be necessary to introduce into the charge: 1. The proper quantities of sillphur-bearing ingredients, to effect a complete separation of copper and lead; and, 2. Sufficient silica and iron oxide, to form with the lime and magnesia of the ore, a slag of the required fluidity. The first condition could be fulfilled only very imperfectly, there being no iron pyrites in Railroad, nor in the surrounding districts. The nearest occurrence is in Battle Mountain, whence a supply could not be procured in time. The second condition, i. e., the addition of iron ore and quartz, was easily complied with, there being an abundance of these materials in the vicinity. The furnace of the Empire City Company, is a small shaftfurnace, with an area of hearth of six square feet, and is supplied with blast by a NO. 4 Root blower. In spite of this small size the furnace smelted during this campaign, which lasted 31 days, an average of 28 tons of ore, and 13 tons of fluxes, together 41 tons of charge, per twenty-four hours. The following tables give the complete data in regard to the smelting process, and the results obtained:

By J. L. Bruce

' For a number of years, from an economic standpoint, the ventilation of the Colorado mine of the Davis-Daly Copper Co. has been a difficult problem. The development through the main hoisting shaft was pursued for a number of years and to a depth of about 2500 ft.(762 m.)before large bodies of good commercial ore were opened. This lack of early success in exploration restricted expenditures for ventilation, with the result that the present orebodies were developed at a depth of 2500 ft., and in country rock of relatively high temperature, without adequate means of supplying the development faces and the stopes with cool or fresh air of low humidity and suitable velocity. During the progress of development, two or three connections were made at higher levels with the workings of adjoining operations, but these were of a makeshift and unsatisfactory character and afforded no means for carrying downcast air from the surface, in anything approaching a direct course, to the working faces. During the latter part of 1917, arrangements were made with the Anaconda Copper Mining Co., whereby, during the year 1918 and the early part of the year 1919, a crosscut was driven eastwards on the 2500-ft. level of the Colorado shaft and connection was made by means of an up-raise of approximately 200 ft. to a crosscut driven westwards from the 2800-ft. level of the Belmont mine, this crosscut at the top of the raise being driven at Davis-Daly expense by the Anaconda Copper Mining Co. This connection, in conjunction with a No. 11 Sirocco fan installed near the Colorado shaft, provided the Colorado mine with a maximum of approximately 30,000 cu. ft. per min. of relatively fresh air, most of which came in a fairly direct route from the downcast Belmont shaft through the No. 11 fan to the 2500-ft. level stopes. After passing through these stopes and the stopes of overlying levels, it passed through the main crosscuts on higher levels back to the Colorado shaft, which provided the upcast for this current of air. The improvement noted on the completion of this work was marked, and, for a time, fairly satisfactory. Further extension of the mine workings, however, and

Jan 1, 1922

By E. T. Dumble

The history of the several petroleum deposits of Texas and Mexico, or of the sediments in which they now occur, if the deposits are not indigenous to such sediments, is known in a general way only, but it nevertheless casts strong light on the conditions surrounding them and is of great importance in the search for and exploitation of them. The petroleum deposits of Texas are separable into two main divisions: 1. The deposits of northwestern Texas, which are directly connected with the Oklahoma fields to the north, and have no representatives at all in the Mexican area. 2. The deposits of the coastal area, which extend into Louisiana on the east and connect with those of the Mexican coast to the south. Early in the Pennsylvanian period a series of bituminous shales and limestones were laid down over a broad area in Texas, Arkansas, and Oklahoma. These are known as the Bend series in Texas, the Caney shales in Oklahoma, and the Fayetteville beds in Arltansas. Following their deposition an uplift occurred, forming the Lampasas geanticlinal, which runs northeastward from the old Paleozoic land area of the Llano region toward Red River. The Bend series is petroliferous in places and has furnished a few producing wells on each side of the Lampasas uplift. This uplift forms the barrier and dividing line between the two divisions of the Texas petroleum deposits. To the west of it, in waters which were the southcrn extension of the interior continental seas, in connection with the sedimcnts and coal beds of the Pennsylvanian and Permian, great quantities of petroleum were deposited either as oil or as "potential petroleum." These sediments have been subject to very slight disturbance, and only very gentle folds are found, with no signs of volcanic action in any part of the area. The conditions, therefore, indicate that the greater part, if not all, of the oil in this area is indigenous to the beds in which it is found. East of the anticlinal the oldest beds which appear in contact with the Bend are the Trinity Sands of the Lower Cretaceous. No evidence has

Jan 1, 1916

The authors have done a very thorough job in analyzing the factors affecting turndown sulfur performance at Inland's No. 4 B.O.F. While many of the results are not unexpected, it is helpful I am sure to have quantified many of the relationships that the operators rely upon daily. On the other hand, however, the results shown for ladle skimming are very surprising. I do not doubt the statistical relationship shown but I feel, based on our experience at Youngstown, that some other parameter has been ignored in the data on ladle skimming. It was our experience that by skimming our hot metal transfer ladle we could reduce our lime consumption by eleven percent while obtaining sulfur removal comparable to that shown by the authors. I would like the authors comment of similar adjustments on the lime charge that were made on skimmed heats at Inland. If not, it would seem that one could gain more desulfurization in the B.O.F. by raising the hot metal manganese than by installing a skimmer. The author's state that no comparisons are valid between the data sets for the two time periods involved because of the difference in the consumption of No. 2 Bundles. I feel this in fact is one of the important conclusions to be drawn from the paper, as there seems to be approximately a 10-20 percent difference in percent of heats that are under 0.020 percent sulfur for similar conditions, which is an extremely important difference with today's demands for low sulfur. I would like the author's comments on the difference in the amount of 82 bundles consumed. Along this same line I was quite surprised by the relatively low number of heats that had a first turn down of 0.020 percent sulfur or less. Also rather disconcerting are the conditions necessary to achieve a first turn of 0.020 percent sulfur, 50 - 60 percent of the time, as required by today's specifications. It is a problem which we are well aware of, but the numbers are still shocking.

Jan 1, 1972

By A. W. Faheneald, Lewis S. Prater

By taking advantage of the fundamental difference between screening and classification—namely, that specific gravity has no effect on screening but is one of the important factors in classification—a combination of the two may be used as a process of mineral concentration. Although this fact is not new, so far as is known it has had little or no commercial application. The scheme is not presented now as a process for producing finished products but rather as a preliminary operation rejecting part of the barren material from an ore before it is subjected to more costly treatment. That is largely the function of the new heavy-media concentration processes that have been widely accepted. Original installation costs for the present sink-float processes are relatively high, however, which confines their use to operations where large tonnages are handled. Sink-float has been successful on only the relatively coarse (approximately plus 10-mesh) portion of an ore, and it is in this same range that classification screening can function most satisfactorily. Theoretically, there is no upper limit to the size of particles that can be handled in a sink-float operation, but the degree of liberation in the very large pieces usually limits this. With classification screening, particles from % to % in. would be the largest that could be handled, but the lower range could be extended somewhat below 10 mesh. In order to take full advantage of the difference in specific gravities of the minerals being separated, sorting in the classifier should be under as extreme hindered-settling conditions as possible. Laboratory tests have been made on a galena ore and on an artificial mixture of quartz and magnesite to determine the separations that may be expected. Although more than one scheme may be followed, in these tests the separations were made by cutting the underflow from the classifier as a concentrate and then screening the overflow. The screen oversize was rejected as a tailing. Classification was done in a hindered-settling teeter column and screening was done by hand, using the standard 4 2 series. The accompanying flowsheet gives the testing procedure followed.

Jan 1, 1947

By A. W. Faheneald, Lewis S. Prater

By taking advantage of the fundamental difference between screening and classification—namely, that specific gravity has no effect on screening but is one of the important factors in classification—a combination of the two may be used as a process of mineral concentration. Although this fact is not new, so far as is known it has had little or no commercial application. The scheme is not presented now as a process for producing finished products but rather as a preliminary operation rejecting part of the barren material from an ore before it is subjected to more costly treatment. That is largely the function of the new heavy-media concentration processes that have been widely accepted. Original installation costs for the present sink-float processes are relatively high, however, which confines their use to operations where large tonnages are handled. Sink-float has been successful on only the relatively coarse (approximately plus 10-mesh) portion of an ore, and it is in this same range that classification screening can function most satisfactorily. Theoretically, there is no upper limit to the size of particles that can be handled in a sink-float operation, but the degree of liberation in the very large pieces usually limits this. With classification screening, particles from % to % in. would be the largest that could be handled, but the lower range could be extended somewhat below 10 mesh. In order to take full advantage of the difference in specific gravities of the minerals being separated, sorting in the classifier should be under as extreme hindered-settling conditions as possible. Laboratory tests have been made on a galena ore and on an artificial mixture of quartz and magnesite to determine the separations that may be expected. Although more than one scheme may be followed, in these tests the separations were made by cutting the underflow from the classifier as a concentrate and then screening the overflow. The screen oversize was rejected as a tailing. Classification was done in a hindered-settling teeter column and screening was done by hand, using the standard 4 2 series. The accompanying flowsheet gives the testing procedure followed.

Jan 1, 1947

By A. W. Fahrenwald, Lewis S. Prater

BY taking advantage of the fundamental difference between screening and classification-namely, that specific gravity has no effect on screening but is one of the important factors in classification-a combination of the two may be used as a process of mineral concentration. Although this fact is not new, so far as is known it has had little or no commercial application. The scheme is not presented now as a process for producing finished products but rather as a preliminary operation rejecting part of the barren material from an ore before it is subjected to more costly treatment. That is largely the function of the new heavy-media concentration processes that have been widely accepted. Original installation costs for the present sink-float processes are relatively high, however, which confines their use to operations where large tonnages are handled. Sink-float has been successful on only the relatively coarse (approximately plus 10-mesh) portion of an ore, and it is in this same range that classification screening can function most satisfactorily. Theoretically, there is no upper limit to the size of particles that can be handled in a sink-float operation, but the degree of liberation in the very large pieces usually limits this. With classification screening, particles from 3/8 to 1/2 in. would be the largest that could be handled, but the lower range could be extended somewhat below 10 mesh. In order to take full advantage of the difference in specific gravities of the minerals being separated, sorting in the classifier should be under as extreme hindered-settling conditions as possible. Laboratory tests have been made on a galena ore and on an artificial mixture of quartz and magnesite to determine the separations that may be expected. Although more than one scheme may be followed, in these tests the separations were made by cutting the underflow from the classifier as a concentrate and then screening the overflow. The screen oversize was rejected as a tailing. Classification was done in a hindered-settling teeter column and screening was done by hand, using the standard [v2]series. The accompanying flowsheet gives the testing procedure followed. [ ]

Jan 1, 1945

In an address delivered at Atlantic City, N. T., Dec. 5, 1918, M. L. Requa, General Director, Oil Division of the United States Fuel Administration, said: We face a new era with all its uncertainties. We have arrived at the period of reconstruction and are face to face with the problems concerning which we have so often speculated during the past four years. In all this reconstruction work the United States must bear an important part. We are looked upon to lead the way, to blaze the trail and our actions will have a profound influence upon the rest of the world. If we are to succeed, even in part, we must not be ashamed to practise economy; we must not despise the clay of small things; the little savings; we must have the closest cooperation between Government and industry. Just as truly do we need civic awakening. All that we have ever fought for, the liberty of the world, is comprehended in the ballot; and yet how lightly we have held this great privilege! We need, if we are to reap in full the benefits of the past 18 mo., an awakened civic consciousness; a jealous guarding of government; a resolution that we will, each and all, perform to the full the duties imposed upon us by Democracy; that we will perform more completely the obligations resting upon us as citizens. During the war, industry, through sane cooperation and intelligent effort, has accomplished results possible of attainment in no other way. Government and industry have worked hand in hand and pointed the way o to future activities which, if realized, can but be most highly beneficial to all. If Government and industry are to fulfill their respective duties satisfactorily, it is obvious that there should be complete mutual confidence. Industry must not attempt to "put something over"-and Government must treat with industry upon the high plane that has characterized the public utterances of the President during the war. The individual who cannot conform to these high ideals should have no place in industry, and equally no place in Government. If the dignified and broad princi-

Jan 2, 1919

By W. P. Haynes

No wildcat operations are recorded from France during the past year, and no new discoveries have been made. In northern Africa, in Morocco, some prospecting continued in the Gharb and Tselfat regions. Only very small production or shows were found. At the close of the year one cable-tool well (depth 400 meters) was drilling in the Tselfat district, and one rotary well in the Gharb. In Tunisia one well was drilling at Sloughia. Refinery building has been active under the new petroleum law, no less than six plants now being under construction. At Pechelbronn, it is estimated 130 wells were drilled, of which 73 wells, or 56 per cent, were productive. Total drilling was 45,000 m. One new Jurassic horizon was discovered. In the mining area approximately 17,500 m. of new gallery were driven. Production at Pechelbronn for the first nine months was as follows: From wells, 233,013 bbl.; from mines, 164,815 bb1.—a total estimated production for the year of 532,000 bbl. Production at Gabian was 3780 bbl. for the year. In Algeria production from Tliouanet was small, being estimated at 6510 bbl. This production is from Helvetian sands (Miocene) around a salt plug. Italy Production for the year was 211,500 bbl., an increase of 62 per cent over that of last year. Drilling to the extent of 97,000 ft. was done mainly by the A. G. I. P., the government company in the Province of Emilia. More locations are being tested in this area, where geophysical results have shown indications of buried uplifts. Oil has been encountered on two of these structures, at Fontevivo and Podenzano, but the wells have given trouble with salt water. The chief producer is the Societa Petrolifera Italiana at Salsomaggiore and Valezza. The production is from sand lenses at relatively shallow depths. New concessions of 2000 hectares were granted at several points in the Po Valley, and geophysical work is being carried on. The A. G. I. P. is working on a five-year program of exploration to test new areas.

Jan 1, 1933

T. R. HARRISON, Washington, D. C. (written discussion). *-Mr. Kowalke shows that a high resistance millivoltmeter is subject to smaller errors, due to change in resistance of the thermocouple to which it is attached, than is a low-resistance instrument. He uses as examples instruments having resistances of 30 and 2 ohms, respectively. At the Bureau of Standards, resistances above 300 ohms would be considered high and 30 ohms rather low. In the tests on calorized-iron thermocouples, a difference between the first and third calibrations of the couples serves to show changes due to the intermediate heat treatment and only under certain conditions would changes in calibrations due to changes in the wire be detected by ,a recalibration after 1 1/2 in. had been cut from the hot-junction end of the couple and the ends rewelded. The calibration of a couple depends only on the thermoelectric prop-erties of that part of the couple which lies within the region of non-uniform temperature, i.e., the temperature gradient; hence, so long as the temperature gradient falls along wires of similar thermoelectric properties no change in the electromotive force is produced by altering the metals of those parts of the circuit that are at uniform temperature. Usually at the cold-junction end of the circuit, copper leads, brass binding posts, manganin resistance coils, and various other materials form part of the circuit, but so long as all are at a uniform temperature (or if for each junction between unlike metals there is a similar opposing junction at the same temperature) no resultant thermoelectromotive force will be produced thereby. Likewise, if a length of several inches at the hot-junction end of the couple is at uniform temperature, it matters not if this section is unlike other parts of the couple, so long as there is good metallic connection and no source of e.m.f. other than thermoelectric is present. Cutting off part of the hot end of the couple within such a region of uni-form temperature would not alter the e.m.f. of the couple.

Jan 12, 1919

By C. J. Delisio

The basic concept of tunnel boring has not changed since the late 1800's. R. Stanley of Great Britain obtained a Canadian patent as early as December 1891. Mr. Stanley's machine was a device that consisted of a rotating wheel equipped with drag-type teeth; it had a means of thrusting the cutterhead against the face or heading; it had a means of clamping or gripping the machine in its bore; it had a means of collecting and depositing the cuttings into a screw-type conveyor located near the invert of the tunnel. It even had a means of varying the speed of the forward motion of the machine to suit different hardnesses of rock encountered. This description essentially fits the latest tunnel-boring machines being built today. In short, there has been no significant advance in the basic concept in 70 to 80 years. It may well be that no significant change can be expected for some time into the future. Today's machines, while still basic in concept, offer many advances aimed at faster tunneling. Among these are 1 ) improved cutters, 2) guidance and steering devices, 3) dust-control devices, and 4) mechanisms to aid in installing tunnel supports. CUTTERS The most important part of a hard-rock tunnel borer is the cutter. If the cutter can cut the rock, it is a boring machine. If the cutter cannot cut the rock, no other part of the machine can. When Jarva, Inc. decided to build a machine, the first problem was to find a good cutter. In our search, we looked at most of the cutters on the market. We selected Reed Drilling Tools' cutter because the design of their cutter was aimed at hard-rock tunneling. We feel that they build the best cutter available and provide the best possible service to their customers. As tunnel-boring machine design advanced, the transition from drag bits to roller bits was natural because harder formations required a roller bit, and it is the goal of all mole users to bore harder formations. Roller bits

Jan 1, 1970

By Walter M. Stephen

MODERN developments in alloy steels have been so rapid and diverse that engineering practice has scarcely had time to re-appraise all items of past experience wherein conclusions became axiomatic under conditions that no longer apply. A case in point is the wet screening of abrasive ores within the fine range still looked upon as belonging exclusively to classifiers. By virtue of the development of stainless steels (18 per cent Cr, 8 per cent Ni), it is no longer true that classifiers are more economical than screens in closed circuit with large-tonnage ball or rod mills at 65 or even 100 mesh, provided a selective overgrind of the higher-gravity constituents of the ore is not desired. Wet screening of ores is a highly corrosive as well as an abrasive operation, because of the inevitably high degree of oxygenation of the water. Screen cloth of ordinary or spring-steel wire almost at once becomes pitted arid covered with a film of corrosion products, which causes rust-blinding of fine-mesh screens and offers high frictional impedance to the flow of ore particles. On the other hand, the well-known properties of stainless steel enable it to maintain a bright surface, and so to eliminate blinding either by ore particles or by corrosion products. That a large-tonnage mill grinding hard ore to 65 mesh can be operated economically in closed circuit with screens instead of classifiers has recently been demonstrated at the Copper Cliff concentrator of the International Nickel Co.; in the test to be described, a 6 ½ by 12 ½ -ft. Marcy rod mill ground from 625 to 820 tons of ore per day to approximately 65 mesh, operating in closed circuit with three 4 by 5-ft. Hum-mer screens, without any classifier. Stainless-steel cloth gave an indicated life of several months. There was no difficulty with blinding, yet dilution and spray water could be controlled so that screen undersize averaged not less than 40 per cent solids. In contrast, ordinary carbon steel was pitted and blind with rust within 40 hours.

Jan 1, 1938