Search Documents

By Castle. J. E., J. L. Gillson

In this chapter there is a wide difference in the meaning of some words used for rock and mineral names as defined by scientists and tabulated in the "Glossary of Geology and Related Sciences," published in 1957 by the American Geological Institute, and the meaning as used by the commercial producers of feldspar. It is necessary, therefore, to define these terms giving both the "scientific" and the "practical" definitions. There is no ambiguity about the name feldspar itself. This is a general term for a group of related minerals which are silicates of aluminum, combined with sodium, potassium and calcium. The feldspars are the most abundant minerals of the igneous rocks, and since these rocks make up the largest proportion of the earth's crust by volume (although not of the actual surface area of the continental land masses) the feldspars are the most abundant minerals of all. The igneous rocks themselves are classified on the basis of the variety of the feldspar present. The potash feldspars, which are called orthoclase and microcline, are the dominant minerals of the granites and syenites, and of their fine grained equivalents, the rhyolites and trachites. The plagioclase feldspars form an isomorphic series, of which the sodic endmember is called albite, and the lime endmember, anorthite. The members near the sodic end, albite, oligoclase and andesine are the characteristic feldspars of the granodiorites and diorites, and of their fine grained equivalents, the dacites, and andesites. These feldspars-orthoclase, microcline, albite oligoclase and andesine-are the feldspars used commercially. Labradorite, a member of the plagioclase group, in which the lime exceeds the soda in the chemical composition, is the common feldspar of the gabbros, anorthosites, norites, basalts and other so-called "basic" rocks. Although some attempts have been made to use labradorite as a commercial feldspar, none is now used except as an ornamental stone. The mineral anorthite is very rare. Since the feldspar in most of the common igneous rocks is relatively fine grained, and mixed intimately with other minerals, from which it can be separated cleanly only with difficulty, most masses of the common rocks cannot be used as sources for the feldspar contained in them. It is only the rarer types of rocks in which the feldspar is very coarse-grained, or ones containing very little of the iron-bearing minerals which are objectionable impurities in commercial feldspar, that are quarried to yield an acceptable product. The most widespread type of such a rock from which commercial feldspar can be produced, is that called "pegmatite." These rocks are dikes and bodies of irregular shape and of a size measured in feet or yards in most cases, rather than in miles. They are more commonly associated with granites, rather than with other coarse-grained igneous rocks. Many of them contain crystals of various minerals, including the feldspars, that are much larger than are found in the host rock, the granite, and in many there are large masses of feldspar that are sufficiently free from iron-bearing silicates so that products acceptable to the ceramic industry can be produced, in some cases simply by hand sorting. Most of this feldspar in pegmatites, however, does contain intergrown quartz up to 25 pct. Pegmatites are so important, not only as commercial sources of feldspar, but also of other minerals which are produced com-

Jan 1, 1960

By W. Bonfield

The microstrain characteristics of a polycrystal-line Cu 1.9 wt pet Be precipitation-hardening alloy have been determined for various conditions of aging. The friction stress remained constant for all the conditions investigated, whereas the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-8 in. per in.) and the three-stage stress-strain curve in the microstrain region were sensitive to changes in dislocation and precipitate distribution. Correlations between the measurements of microplasticity and electron-nzicroscope observations of substructure are considered. ALTHOUGH the macroscopic mechanical properties of Cu 1.5 to 2.0 wt pet Be precipitation-harden ing alloys were established' in some detail, there has been no previous investigation of the nature of microyield-ing in these alloys. This paper describes a high-sensitivity extensometer determination of microplasticity in polycrystalline Cu 1.9 wt pet Be, in which the friction stress, the microscopic yield stress (the stress to produce a plastic strain of 2 x 10-6 in. per in.), and the rate of strain hardening in the micro-strain region were measured for various conditions of precipitation. The structural changes accompanying aging in this alloy were examined using transmission electron microscopy, a study which differed from previous investigations as, in order to minimize grain boundary precipitation effects,' the solution-treated alloy was cold-rolled to 40 pet reduction prior to aging. Hence the extent of recovery and recrystalliza-tion, as well as the variation of precipitate morphology and distribution, were assessed. From these results possible correlations between the microstrain characteristics and the observed precipitate and dislocation structure are considered. EXPERIMENTAL PROCEDURE The material investigated was a commercial copper beryllium alloy (Berylco 25), which had a com- position of 1.9 wt pet Be and 0.2 wt pet Co. The alloy was solution-treated at 800°C, quenched in water, and then cold-rolled to 40 pct reduction. Tensile specimens of gage length 1 in. and rectangular cross section of 0.18 by 0.06 in. were prepared from the solution-treated, cold-rolled material and aged for 15 min, 2, 24, and 100 hr at 315°C and 24 hr at 425°C to produce a range of precipitate structure. The hardness values associated with these conditions are listed in Table I. It can be seen that a maximum value is obtained after 2 hr at 315oC, which decreases with continued time at temperature to a minimum after 24 hr at 425°C. For comparison some as-solution-treated specimens were also aged for 2 hr at 315°C. The specimens heat-treated to a given condition were examined in two ways. First, the nature and distribution of the precipitate and dislocation structure was characterized using transmission electron microscopy. Thin foils were obtained from the specimens by electrolytic polishing in a 30 pet nitric acid-alcohol solution at -20oC, and were examined in an RCA EMU 3 electron microscope. Second, the mi-croplastic behavior of the specimens was measured with a Tuckerman strain gage, using the load-unload technique previously described2, 3 to determine the friction stress, the microscopic yield stress, and the variation of plastic microstrain with stress. RESULTS 1) Structural Changes During Aging. a) Annealing Processes. The solution-treated, cold-rolled Cu 1.9 wt pet Be had an irregular dislocation-cell structure,

Jan 1, 1968

The Board of Directors has authorized the following offers of sets of back volumes of the Transactions, at considerably reduced prices, to Members, Libraries, and Scientific Societies Per Set. I. Five volumes, bound in half-morocco, from No. 36 (1906) to No. 40 (1910), . $20 II. Ten volumes, bound in half-morocco, from No. 31 (1902) to No. 40 (1910), including Mexican Volume, 35 III. Twenty volumes, bound in half-morocco, from No. 21 (1893) to No. 40 (1910), 50

Jan 4, 1913

By H. F. Kendall, J. H. Ffolliott

MANY papers and reports have been devoted to the geology and ore deposits of the Ducktown district, Tennessee, especially the complete report by W. H. Emmons and F. B. Laney, published as Professional Paper 139, by the U. S. Geological Survey. The present paper discusses the work of the geological organization of the Tennessee Copper Co., which is based on the field work of the above paper and the consulting work of W. H. Emmons. The Ducktown basin lies in the southeastern corner of Tennessee and extends a short distance into Georgia and North Carolina. All productive mines are contained in an area of 15 sq. mi. in the center of this basin, which is an undulating plateau at an elevation of 1650 to 1800 ft. above sea level. It is surrounded by the relatively high mountains of the southern Appalachian region. The rocks are of early Cambrian age. Deposition of the ores probably took place during the latter part of the Paleozoic era. The ore deposits are rudely tabular to lens-shaped bodies of massive sulfide, varying from a few feet to over 200 ft. in width. In general they all strike northeast and dip southeast at angles from 45° to 70°. Locally, where affected by folding and faulting, the variations in dip may be even greater. The lodes usually are parallel at distances of from one-half to one mile measured normal to the strike. The deposits are a replacement of a fairly continuous bed or a series of disconnected limestone lenses, highly folded and somewhat faulted, which probably represent the same stratigraphic horizon.

Jan 1, 1933

By V. V. Clark

WHEN a district is more or less primitive, and a trained mining engineer attempts single- handed to prospect it according to old standards, he generally fails. He has not the ability to live out in the open alone for months at a time and carry on with enthusiasm and determination like the old-time prospector. But the same engineer, placed in an organized group where modern prospecting methods are employed, is immediately put on his mettle and his chances of winning are greatly increased. Marsman Investments, Ltd., with headquarters in Manila, has at the present time, Sept. 4, 1937, six prospecting parties in the Netherland East Indies. Three of these groups are combing their assignments for lode mines, studying structures, developing and reaching out into veins and zones with diamond drills. The other three are searching for placer mines with pans, pits, and Empire drills. I am in charge of one group seeking commercial gold placers on the Island of

Jan 1, 1937

By Alan M. Bateman

POSSIBLE postwar trends of the more important world minerals will be determined in part by their present world position and by the acts and forces that have operated during the war period, so it is desirable first to review briefly what has been happening in the foreign field of metals and minerals. When we first entered this war we of the mineral profession were all acutely conscious of our lack of strategic minerals and other materials, which had to be imported in great quantities-minerals such as manganese, chrome, tin, mercury, nickel, and antimony. But we realized also that we had to acquire vast quantities of those minerals of which we had thought we were bountifully supplied. Our assumed domestic abundances turned out to be woefully deficient, and demands also arose for new minerals never before produced in large quantities. Some threescore minerals entered the strategic list of our imports. Ores from new sources had to be sought, developed, and transported. Tonnages in the millions of such bulk materials as zinc, lead, copper, chrome, and manganese flowed to feed our war efforts. Sparsely distributed minerals such as tin, mercury, antimony, tungsten, cobalt, mica, and corundum had to be lured from their rock lairs in greatly increased quantities to feed the hungry maw of war industry, and the rare minerals such as tantalite, columbite, beryl, and quartz crystals had to be developed and procured in quantities never before dreamed of. New uses such as radio and radar created demands for many minerals formerly thought of only as adornments of museum collections and not as pressing industrial minerals. Such minerals were never before mined in quantity.

Jan 1, 1945

By Clinton H. Crane

DR. TILNEY, the great expert on the study of the development of the brain of human beings and animals, tells us that the greatest difference between the human brain and the brain of animals is that man alone has shown evidence of being able to predict the future. Just why he throws overboard the busy bee who lays up honey for the winter, the squirrel who gathers nuts, and the humble ant, I do not know. At any rate, it is nice to be assured by an authority that we have this power of prophecy. My own experience with attempting to prophesy the future has convinced me that our only possibility of being good prophets is to be good students of history.

Jan 1, 1940

By H. P. Greenwald

IN the year just passed the Coal Division's Committee on Rock-Dusting reviewed the status of this safety measure in American coal mines and prepared a paper thereon which will be presented at the February meeting of the Institute. This paper supplements one appearing in Vol. 139 of the "Transactions," page 87 (1940). Because that paper will be issued soon, only a summary is given herein.

Jan 1, 1944

By G. C. Trevorrow

STRIP mining during 1943 increased considerably with further extension of mechanical loading in mines already partly mechanized; with the considerable introduction of mechanical loading into hand-loading mines; and with improvements in the use of loading equipment. Extension of the use of machinery both in strip mining and underground is due to reduction in labor supply and increased cost of labor, together with the increased demand for coal during the period of labor shortage.

Jan 1, 1944

By J. L. Craig, C. L. Edwards, M. D. Harper, J. M. Ray

The Los Alamos National Laboratory executed 19 intermediate scale cratering experiments in oil shale at the Colony Mine in Garfield County, Colorado. These experiments have led to a better under- standing of fracture characteristics and fragmentation of & - oil shale by use of a conventional high explosive. Geologic site characterization included detailed mapping, coring, and sample analyses. Site-specific geology was observed to be a major influence on the resulting crater geometry. The joint patterns at the experimental site frequently defined the final crater symmetry. Secondary influences included vugs, lithology changes, and grade fluctuations in the local stratigraphy. Most experiments, in both the rib and floor, were conducted to obtain data to investigate the fragmentation results within the craters. The rubble was screened for fragment- size distributions. Geologic features in proximity to the explosive charge had minimal effect on the rubble due to the overpowering effect of the detonation. However, these same features became more influential on the fracture and rubble characteristics with greater distances from the shothole. Postshot cores revealed a direct relationship between the grade of the oil shale and its susceptibility to fracturing. The Colony Mine experiments have demonstrated the significant role of geology in high explosive/oil shale interaction. It is probable that this role will have to be considered for larger applications to blast patterns and potential problems in retort stability in the future of oil shale development.

Jan 1, 1983

By L. M. Pidgeon, P. G. Thornhill

A LTHOUGH a considerable number of experi--ti mental investigations dealing with the roasting of sulfide minerals have been reported in the past,'"" the behavior of the single roasting particle does not appear to have received the attention it perhaps deserves. This is understandable in that the natural sulfide counterpart of the slab or sheet of metal normally used in high temperature oxidation studies is difficult to obtain and prepare, and is, in most cases, virtually impossible to maintain in one piece at roasting temperatures. The employment, on the other hand, of static aggregations of small particles in masses great enough to permit evaluation of the roasting reactions by means of thermobalances or gas analyses introduces other complications, such as localized overheating, sintering, and variable gas-solid contact. In this investigation a compromise between the above extremes was attempted. Closely sized (e.g., 30 to 40 mesh) particles of natural sulfide minerals were isothermally roasted, out of contact with one another, in an air-swept system. The progress of the roasting reactions was followed by examination in polished section of the treated particles and by X-ray and chemical analysis of their residual sulfide kernels. In this way some conclusions respecting the mechanism of roasting reactions were drawn. Roasting Furnace—The vertical tube furnace used for roasting the sulfide particles had a heated zone 10 1/2 in. long in which four retractable light gage stainless steel trays were suspended. Each tray, and an accompanying baffle, was mounted on a 2 in. lengtn of 3/8 in. stainless steel tubing. These assemblies were axially suspended on a 30 in. length of ¼ in. stainless tubing, by means of which they could be lifted from the hot zone to a water-cooled brass chamber at the top of the furnace. Since each tray unit could slide freely on the 30 in. tube, any desired number of the trays could be retained in the cooling chamber by the manipulation of a horizontal plunger during a momentary withdrawal of the four trays from the hot zone. Although three heating coils, each equipped with variable external resistance, were employed, it was found impossible to avoid a drop of 10o to 15oC between the temperature at the top tray and that of the lower three. Consequently, only the bottom three trays were used for roasting. Temperature readings inside the furnace were made by means of a thermocouple inserted down the tray support tube at tray levels, and a separate thermocouple, inserted adjacent to the middle heating coil, was connected to a Micromax temperature control unit. Experimental Method—The sulfide minerals were obtained in a form as free as possible from gangue and contaminating sulfides, and were crushed and screened to the required particle size range. The tray assembly was kept inside the furnace during the heating-up period and, when a steady temperature had been reached, the trays were withdrawn. Each tray was sprinkled with from 200 to 500 mg of the sulfide grains, and the assembly was lowered into the furnace without delay in order to minimize the time required to achieve the operating temperature. The furnace top was then clamped into position and the thermocouple inserted down the center tube to the required level. It was found that, when this procedure was used, the trays achieved their former temperature within 2 min, after which time the flow of dry air was begun at a rate of 1 liter per min, and timing of the run was started. At the required intervals of time the trays were successively withdrawn from the hot zone and stored in the cooling chamber by means of the retention plunger. On completion of the run the treated particles were removed from the trays to be set aside for examination. The roasted particles were mounted in Lucite on a Buehler press Operating at a temperature of 140°C

Jan 1, 1958

By J. H. Wernick, D. Dorsi, K. E. Benson

A LTHOUGH a considerable number of experi--ti mental investigations dealing with the roasting of sulfide minerals have been reported in the past,'"" the behavior of the single roasting particle does not appear to have received the attention it perhaps deserves. This is understandable in that the natural sulfide counterpart of the slab or sheet of metal normally used in high temperature oxidation studies is difficult to obtain and prepare, and is, in most cases, virtually impossible to maintain in one piece at roasting temperatures. The employment, on the other hand, of static aggregations of small particles in masses great enough to permit evaluation of the roasting reactions by means of thermobalances or gas analyses introduces other complications, such as localized overheating, sintering, and variable gas-solid contact. In this investigation a compromise between the above extremes was attempted. Closely sized (e.g., 30 to 40 mesh) particles of natural sulfide minerals were isothermally roasted, out of contact with one another, in an air-swept system. The progress of the roasting reactions was followed by examination in polished section of the treated particles and by X-ray and chemical analysis of their residual sulfide kernels. In this way some conclusions respecting the mechanism of roasting reactions were drawn. Roasting Furnace—The vertical tube furnace used for roasting the sulfide particles had a heated zone 10 1/2 in. long in which four retractable light gage stainless steel trays were suspended. Each tray, and an accompanying baffle, was mounted on a 2 in. iength of 3/8 in. stainless steel tubing. These assemblies were axially suspended on a 30 in. length of in. stainless tubing, by means of which they could be lifted from the hot zone to a water-cooled brass chamber at the top of the furnace. Since each tray unit could slide freely on the 30 in. tube, any desired number of the trays could be retained in the cooling chamber by the manipulation of a horizontal plunger during a momentary withdrawal of the four trays from the hot zone. Although three heating coils, each equipped with variable external resistance, were employed, it was found impossible to avoid a drop of 10O to 15OC between the temperature at the top tray and that of the lower three. Consequently, only the bottom three trays were used for roasting. Temperature readings inside the furnace were made by means of a thermocouple inserted down the tray support tube at tray levels, and a separate thermocouple, inserted adjacent to the middle heating coil, was connected to a Micromax temperature control unit. Experimental Method—The sulfide minerals were obtained in a form as free as possible from gangue and contaminating sulfides, and were crushed and screened to the required particle size range. The tray assembly was kept inside the furnace during the heating-up period and, when a steady temperature had been reached, the trays were withdrawn. Each tray was sprinkled with from 200 to 500 mg of the sulfide grains, and the assembly was lowered into the furnace without delay in order to minimize the time required to achieve the operating temperature. The furnace top was then clamped into position and the thermocouple inserted down the center tube to the required level. It was found that, when this procedure was used, the trays achieved their former temperature within 2 min, after which time the flow of dry air was begun at a rate of 1 liter per min, and timing of the run was started. At the required intervals of time the trays were successively withdrawn from the hot zone and stored in the cooling chamber by means of the retention plunger. On completion of the run the treated particles were removed from the trays to be set aside for examination. The roasted particles were mounted in Lucite on a Buehler press operating at a temperature of 146°C

Jan 1, 1958

By WILFRED SYKES

IT is with particular pleasure that I welcome the members of the Open-hearth Conference of the I American Institute of Mining and Metallurgical Engineers to this meeting, as I feel this is one of the most useful activities of the Institute in the field of ferrous metallurgy. For the information of our other members I might say the Open-hearth Conference was organized by Mr. Reynders when he was president, and is made up of open-hearth superintendents and metallurgists. All the plants are invited to send representatives, and practically all do, with the exception of the U. S. Steel Corporation. It meets twice a year to discuss various problems in connection with the manufacture of steel, and its minutes are published for the benefit of those attending, the expense being defrayed by the participating companies. This conference, .1 believe, should be a model for activities in the other branches of the work covered by this Institute. It works, not by reading formal papers, which we all know is not a very satisfactory method to bring out the experience of others, but rather by a round-table method of discussion. The spirit of the meetings is such that each member feels perfectly free to state his experience, and he gets as much as he gives. A series of topics for, discussion is brought to the attention of the chairman and after one is exhausted the next point is taken up. In this way there is a real interchange of ideas and experiences which cannot fail l to be of the greatest benefit to those attending. That these meetings are beneficial is evidenced by the "continued growing attendance and lively discussions at these half-yearly meetings.

Jan 1, 1930

By Henry D. Hibbard

I. INTRODUCTION. THESE impurities are perhaps the most important things in steel-especially steel made by the oxidation processes-the effect of which has not been at least approximately determined. By oxidation processes I mean the Bessemer and Siemens-Martin, during which the metalloids in the charge are removed by oxidation. It has been truly said that it is a clear advantage to have a new name for a new thing. To secure this and to economize space, let us adopt the name sonim (plural sonims) to designate the solid non-metallic impurities existing in steel or other metal. I would define a sonim as a solid non-metallic portion of matter existing as an impurity in metal. A piece of sand, brick, clay, or such material, imbedded in metal, would be considered as a foreign body, not as an impurity, and therefore not a sonim. The studies of sonims of which the results have been published hitherto, have been made chiefly or wholly on finished or at least on cold steel, without much, if any, regard to the specific methods by which the steel was made. While many of the results so obtained are valuable, they give little help in determining the cause, effect, or cure of the disease. It is not enough, in such a study, to know merely the commercial name of the process; for within the field of each process lies a great number of possible variations, each of which will yield a result differing in some respect from all others; and the control of sonims is particularly dependent. on the metallurgical treatment of the metal, because of the inability of analytical chemistry to throw much light on their presence, condition, and effect, as they usually occur in commercial steels. The microscope aids more, perhaps, than chemistry in their study.

Apr 1, 1911

By S. C. Lindsay, D. J. I. Evans

With each year that passes hydrometallurgical processes are being more widely used to recover base metals from ores and concentrates. Generally these processes involve liquid-solid separation of metal-bearing liquors from barren residues. This may be done by countercurrent decantation, thickening and filtration, or filtration or centrifuging only. Choice of method is governed by chemical and physical characteristics of the pulps; cost of labor, power, materials, and waste disposal; and even by the amount of capital available when building plans are under way. Since all these controlling factors change with time and location and with technological advances, the separation method must be re-evaluated when new plants or expansion programs are contemplated. At the Sherritt Gordon refinery in Fort Saskatchewan, Alberta, an ammonia pressure leaching process recovers nickel, copper, and cobalt from the nickel concentrate produced at Lynn Lake, Manitoba.' Pregnant liquors are separated from the barren leach residues in a thickener-filter liquid-solids circuit. The decision to use this type of separation was based on a summation of economic factors during the pilot plant and design stages. Although countercurrent decantation was not incorporated in the refinery flowsheet, the problems solved in thickening the leach residues and the experience gained in operating the commercial plant are pertinent to countercurrent decantation, particularly where it is applied to slow-settling leach slurries or slurries having a relatively high vapor pressure of a valuable, obnoxious, or poisonous vapor. The nickel sulfide concentrate is leached under pressure with air and ammonia to dissolve the nickel, copper, and cobalt and most of the sulfur, leaving a residue of iron and siliceous material to be discarded.2,3 During a subsequent distillation stage to recirculate part of the ammonia used for leaching, copper is recovered from the solution as a high-grade sulfide. After further purification to remove traces of copper and undesirable sulfur compounds, the nickel is precipitated by hydrogen under pressure at an elevated temperature. The cobalt, together with unreduced nickel, is precipitated as a mixed metal sulfide by hydrogen sulfide for eventual cobalt recovery. The end solution is then evaporated to produce a crystalline ammonium sulfate byproduct. As shown in Fig. 1, the nickel concentrate is leached in a continuous, two-stage, countercurrent circuit. In the first stage, or adjustment leach, the fresh concentrate is partially leached (60 pct) in the liquor produced in the second stage, or final leach. This system is necessary to produce a solution suitable for treatment in the copper sulfide precipitation step. Both stages are carried out at 170" to 180°F under a total pressure, with air, of 100 to 120 psig in large, horizontal, water-cooled autoclaves. The autoclaves are divided by overflow weirs into four compartments to give a certain amount of staging during leaching. In each compartment a relatively slow-speed (100 to 150 rpm) agitator maintains the nickel concentrate in suspension. Adjustment leaching, carried out in two autoclaves in parallel, is followed by a thickener-filter liquid-solids separation. Final leaching is done in two parallel trains of three autoclaves using aqueous ammonia to extract metal values from the adjustment leach residues. This too is followed by a thickener-filter circuit. Here the residues are repulped once with aqueous ammonia and twice with process water and refiltered after each repulping stage, to insure a maximum recovery of soluble metal, before being discarded to the tailings pond. The adjustment leach is followed by a seven-disk Dorr-Oliver American filter, with an agitator in the filter boot to keep the residues in suspension. Agitators have also been installed beneath the four ten-disk filters following the final leach thickener. Slurry Characteristics: A typical analysis of the Lynn Lake nickel concentrate, produced by differential flotation,' is given in Table I. The concentrate comprises 35 to 49 pct pentlandite, (Fe, Ni)S; 3 to 6 pct chalcopyrite, CuFeS,; 1 to 4 pct pyrite, FeS2; and 24 to 42 pct pyrrhotite, Fe1-2S (where x varies between 0 and 0.2) together with various siliceous minerals such as actinolite, hornblende, and talc. During leaching, the sulfur in the pentlandite, chalcopyrite, and part of the pyrrhotite is successively oxidized through the thiosulfate and poly-thionate radicals to sulfate and sulfamate." Simultaneously the nickel, copper, and cobalt are converted to soluble ammine complexes and the iron in the pentlandite, chalcopyrite, and part of the pyrrhotite is oxidized to a spongy hydrated iron oxide. The hydrated iron oxide is readily broken down by the agitation needed to sustain the concentrate in suspension and to maintain a satisfactory mass transfer of the oxygen from the air to the slurry. Table I shows typical chemical, screen, and

Jan 1, 1961

By Joseph E. Pogue

THERE are two methods employed in the development of oil pools. The older and dominant method is one in which the primary object is the protection of the underground deposit from drainage through competing wells, and considerations of efficiency of extraction and cost of production are subordinated thereto. The newer and less prevalent method is one in which maximum efficiency and minimum cost are the first objectives and developments to these ends may proceed undisturbed by the exigencies of competitive drainage. The second method has developed mainly in pools under single ownership and the term "unit operation" has come to be applied to this procedure. A single ownership, however, is not essential to the method, for unity of operation may be achieved by agreement under split ownership, or even by a concert of enlightened purpose. There are examples of unit operation where neither the ownership nor the management is a unit, but merely where unity of procedure has been attained, as is the case of the Yates pool. .Throughout this paper unit operation is used in its broad sense without implying sole ownership or single management, although unit operation is more conveniently attained where these conditions are present.

Jan 1, 1930

By R. A. Young

Zinc metal production in the operating plants in the United States during 1948 was approximately equal to that of the year 1947, although new developments during the year assure higher output in 1949, if economic conditions are favorable. In the Western plants, the man-power shortage was almost completely overcome and new capacity has been or is in the process of being added to three plants; thus by December of 1948 daily zinc metal production had risen to the highest point since May of 1944 despite strikes in one large primary smelter and in one secondary plant.

Jan 1, 1949

President Howe : It is not so clear to me that the facts which Dr. Waldo brings forward really argue that the nature of the combination between copper and aluminum differs from that of the combination between copper and zinc or copper and tin. As regards electric conductivity, I suppose that the fact, which he thinks points to a special intimate kind of union between aluminum and copper, is that the line in his Fig. 1 is neither straight nor uniformly curved, but that its curvature varies rapidly, not to say abruptly. But we find just such variation in like curves for the copper-zinc and copper-tin alloys. Thus, a slight addition of zinc or tin to copper causes a change in color wholly out of proportion to the quantity added; and, as we add zinc or tin to copper, the tenacity rises very greatly, only to fall off abruptly with further additions of either of these metals. Dr. Waldo : My curve related only to electrical conductivity. The President : If irregularity in one physical property argues

Jan 1, 1895

By Richard Kunter

INTRODUCTION Additional work has been done on the CIP circuit at Creede, and a brief description of this work is presented in this paper. DREDGE The original dredge for the Bulldog was built by Al Hack, Inc. of Denver. The dredge cutter head is mounted on a boom made of 6-inch diameter pipe which is raised and lowered by a cable-pulley system. Maximum cutting depth is 8 feet. Slurry from the dredge flows through a floating 6-inch diameter pipe supported on 55-gallon drums which runs from the dredge to the shore and then to a trash screen and pumping system. See Figures 1 and 2. The cutter head, suction pump, winches for dredge movement, and all other operations are controlled from a small operations house located toward the rear of the dredge. All of the basic dredge equipment is mounted on a chassis about 8 ft x 16 ft in size. Additional buoyancy was originally provided by sealed 55-gallon drums supported along the sides of the chassis by a small wooden framework. Additional framework and barrels on the front of the chassis on either side of the cutter boom provided additional stability, particularly when digging in hard material. The dredge was quite stable, but two problems were apparent. For one, it could have been sunk by someone from the shore firing a rifle into all of the barrels. In prime deer-hunting and sportsman country

Jan 1, 1983

By AIME AIME

THE annual fall meeting of the Institute of Metals and the Iron and Steel divisions, in conjunction with the American .Society for Steel Treating and the Metal Congress and Show, at Boston was from many standpoints the most successful we have had to date. While many faces were missing from the various gatherings, the Institute registration reached the high mark of 324 members and guests. Cooperating with the Steel Treaters were also the American Society of Mechanical Engineers, the Society of Automotive Engineers and the American Welding Society. ,The meeting was, as usual, a three-ring circus with technical sessions 'galore, plant .trips, visits to the Exposition, social events such as lunch- eons and dinners as well as entertainment for the ladies present.

Jan 1, 1931