Search Documents

By A. K. Mukherjee, J. E. Dorn

A modified Peierls model is Presented for the rationalization of the asymmetric plastic behavior of single crystals of bcc metals. The model assumes that the asymmetry of slip arises from a tendency toward asymnetric splitting of the a/2[111] screw dislocation. The approach differs from former theories however insofar as it assumes that the splitting is so minor ttut only the core energy is modified and that no real partial dislocations exist. As a consequence, the concepts of a line energy of a partial dislocation, interaction between partial dislocations, constriction energies, and stacking fault energies are not invoked. Instead the present analysis is based on a specialization of the Peierls mechanism which assumes an asymmetric dislocation core which is modified by the effective stress and permits cross slip. The theoretical predictions on the stress-temperature -strain rate and orientation relationship agree qualitatively with the limited experimental data that are currently available. Additional experimental work over wider ranges of conditions is suggested to provide more complete evaluation of the possible validity of this theory. RECENT experimental investigations on the low-temperature thermally activated deformation of bcc metals have confirmed the existence of several unique orientation effects. These will be described with the aid of the standard stereographic projection shown in Fig. 1. If slip were determined exclusively by crystal symmetry, the deformation characteristics would be symmetrical about X; = 0 and independent of whether the specimen were subjected to a tension or a compression stress, regardless of what combinations of slip planes might be operative. Experiments, however, reveal that neither of these symmetry based predictions are valid. A schematic representation of the commonly observed asymmetry of both the yield stress and the plane of slip is shown in Fig. 2. A reversal of the direction of stressing results in an inversion of the asvmmetric behavior. 1) Asymmetry bf Yielding. A detailed investigation on the asymmetric yielding in an Fe-2.7 pct Si alloy was repoEted by Tabka, Tikeuchi, and Furubayashi,1 Similar trends have been observed by Keh and Nakada on iron,' Stein on molybdenum,3 Bowen, Christian, and Taylor4 on columbium, Sherwood, Guiu, Kim, and pratt5 on Ta, Cb, and Mo. The degree of asymmetry not only depends on the atomic number and alloying but, in all cases that have been examined, it also increases with a decrease in the test temperature. 2) Asymmetry of the Slip Plane. Asymmetric $I-~: curves of the type shown in Fig. 2 have been found for several Fe-Si alloys6-8,1 and columbium.4 There is general agre_ement that near X: = 30 deg slip occurs by the [111](211) mode so that ?1 = 30 deg. As X; decreases it appears that [111](211) to [111](101) cross slip takes place leading to slip band traces on intermediate planes. And as xi approaches 0 deg, sharp

Jan 1, 1970

By H. K. Work, G. H. Enzian

In the manufacture of steel for commercial purposes, the deoxidation practice used, i.e., the method and degree of deoxidation, is an important factor affecting the structure and mechanical properties of the finished steel. Deoxidation practice exerts a pronounced influence not only on the soundness of the ingots but also on the reaction of the steel to a number of mechanical and thermal treatments. The first mentioned effect of deoxidation is more or less obvious and was first demonstrated, though perhaps not fully appreciated, by Robert Mushet when, in 1856, he added speigeleisen to low-carbon bessemer blown metal. In 1861. Bessemer patented the addition of one pound per ton of silicon to his blown metal to "cause the metal to lie quietly in the mold." The second effect of deoxidation-—that is, the effect on the properties and behavior of the steel—is, one might say, more subtle, and certainly not as well understood as the first, although in many cases it is the more important consideration. This paper is limited to a discussion of only the second effect of deoxidation and: in particular, to the effect on the strain-sensitivity of low-carbon steels. General Discussion Originally it was thought that the function of a deoxidizer was to combine with the oxygen present in the steel as iron oxide and prevent its subsequent evolution as a gas. -More recently it has been realized that a deoxidizer does more than this. Frequent reference has been made to the effect of deoxidizers on the nitrogen in the steel, and some attention has also been paid to hydrogen. As a consequence of the above situation any study of deoxidation must be concerned with the gas content of the steel and the effect of the deoxidizer on the gases involved. The term "gas content" as used here refers to gases extracted from steel during melting in vacuum rather than to elements present in steel in the gaseous state. The extracted gases, at least in the case of oxygen and nitrogen, are generally accepted to be products of decomposition of oxides, nitrides, or other more complex compounds. The manner in which deoxidation affects the gas content of steel and the significance of gases in steel have been and still are subjects of considerable speculation. No attempt will be made here to give a complete discussion of the literature on this subject but a few references will be cited for purposes of illustration. N. Hamilton1 found a correlation between the oxygen content of alloy steel and the behavior of the steel during tube piercing. Davenport, Bain, and others associated oxygen with aging properties of steel while Köster5 and a number of others6-lo made similar claims for nitrogen. Daniloff, Mehl, and Hertyll stated that "deoxidation decreases the susceptibility of steels to aging directly

Jan 1, 1945

By Charles H. Fulton

There are comparatively few accurate data on the melting-or the freezing-point temperature of metallurgical slags, or on related physical phenomena, such as fluidity near the melting-point, specific heat, latent heat, etc. With the exception of the work of H. 0. Hofman,' and some older work by R. Akerman, P. Gredt, and H. M. Howe, no information is available that is of direct interest to the metallurgist. Hofman's valuable work is the only one that refers to slags produced in the metallurgy of copper and lead. The classic work of J. H. L. Vogt,2 who views slags from the standpoint of physical mixtures (solutions in which the entities are minerals), has opened up a new field in the study of slags, and has placed the investigation of such properties as melting-temperatures, etc., on a rational basis. The recent work of A. L. Day, E. T. Allen, and W. I?. White, of the Carnegie Institution, at Washington, and of European investigators3 on certain systems of silicate minerals confirms the value of the investigation of silicate series from this standpoint, and it is my aim to apply this method to metallurgical slags, in order to gain exact data of value in metallurgy. The work recorded in the present paper is the result of an investigation of reverberatory-furnace slags made for a Western smelting company to determine exactly the influence of change in composition, within comparatively narrow limits, on the melting-point. For a general discussion concerning the mineralogical character of slags and the principles on which this investigation is based, reference should be made to other work: for the subject is too large to be stated in this paper, except very briefly in the following outline:

Jan 1, 1913

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson's discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 7 3/4 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612° F. (322° C.), they reduced the 7 3/4 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statement just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson's time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced consumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opinions advanced by different authorities in the scientific world to account for the apparent anomaly, but none,

Jan 1, 1877

By I. Lowthian Bell

THERE has been probably no improvement introduced into the manufacture of iron which created more surprise in the minds of practical smelters and of scientific men than Neilson's discovery of the hot blast. In 1829, Messrs. Dunlop & Co. consumed at the Clyde Works, near Glasgow, nearly 79 tons of coal to make a ton of pig iron, of which about 20 cwts. was employed under the boilers of the blowing engines, leaving nearly 7 tons for the consumption of the furnace itself. In the year 1833, by heating the air to 612' F. (322' C.), they redoccd the 79 tons to 3 tons by the mere burning of 8 cwts. of coal in the apparatus for raising the blast to this temperature. The statenlent just given is strictly true in a commercial sense, but when we come to consider the question as one of physical science, it is necessary to eliminate some of the conditions which conduced to so extraordinary a result. Anterior to Neilson's time the fuel employed in smelting iron was coke, and it was supposed at that period, erroneously, however, that coal in its raw state, when burned with cold air, was totsally unfit for the purpose in question. This mineral, as it was obtained from the Lanarkshire coal-field, contained about 35 per cent. of volatile matter, but the process of charring it was performed in so unskilful a manner that instead of receiving 88 cwts. of coke from 135 cwts. of coal, 60 cwts. only was the product of the operation. Again, the reduced colisumption of carbon in the furnace itself was accompanied by a corresponding diminution of blast, and this was followed by an economy of half a ton in engine coal. After making a proper allowance, however, for all these collateral circumstances, we are within the mark when we admit that in actual coke, which is really the form the fuel has to assume before it is burnt in the blast-furnace, not less than 30 cwts. was saved by heating the blast to 615° F. (322° C.). This unexpected economy, be it remembered, was obtained by the combustion of the 8 cwts. of coal, somewhat wastefully applied in the hot-air apparatus. Numerous have been the opirlions advanced by different authorities in the scientific world to account for the apparent anomaly, bat none,

By John Griffen

THE modern anthracite breaker or washery uses almost completely a wet method of preparation, which requires, roughly, 1 gal. of water per minute per ton of production per day. The entire anthracite industry uses about 320,000 gal. per min. of water for this purpose or 800,000 tons of water per day. As this water leaves the breakers, it contains fine solids-coal, slate, pyrite, and clay-and is then called silt or slush; as slush is the term most commonly used, it will be employed throughout this paper. The solid content of the slush will be referred to as solids. In the earlier days of anthracite mining, little coal was washed, less crushing was employed, and virgin coal was mined exclusively. As a result, the slush problem was not acute because of the relatively small quantity and the coarseness of the solids. Such slush as was produced could usually be easily impounded and retained or could be discharged into streams without any appreciable pollution being apparent. The character of the fine waste from the breakers, changed materially as its quantity increased until now about 40,000 tons of slush solids are produced daily. Second mining and robbing operations materially increased the quantity of fine solids delivered to the breaker in the mine car. The demand for chestnut, stove and egg sizes, to the exclusion of grate, steamboat, and lump sizes, require finer crushing of the mine-run coal with a consequent increase of fine solids in slush. The use of rice and barley sizes removed a considerable tonnage of coarser solids from the slush but left great quantities of fine solids difficult to retain completely and store and long considered of no possible fuel value. Despite the efforts of the coal operators, the slush solids have found their way into the streams causing, in some cases, serious pollution. The Water Supply Commission of Pennsylvania published, in 1916, a report on Culm in the Streams of the Anthracite Region,1 from which the following is taken: About 40,000,000,000 gal. of water carrying 10,000,000 tons of fine culm are discharged into the water-courses direct, flushed into the mines, or disposed of by various means on the surface. The extent to which the very small sizes of anthracite

Jan 9, 1921

By E. C. W. Perryman

The recovery of X-ray line broadening, hardness, and electrical resistivity from cold worked AI-Mg alloys has been investigated. The results, together with those from density measurements, suggest that magnesium atoms freeze in the excess vacancies formed by cold working, and that this affects the climb of dislocations during the recovery process. PREVIOUS work1, " has shown that while 1 pct Mg increases the activation energy for recrystalliza-tion, it decreases the activation energy for the recovery of mechanical properties and decreases the subgrain size both after cold working and annealing. A similar result has been reported by Varley2 for an A1-2 pct Mg alloy. With plastic deformation at high temperatures, McLean and Farmer' and Rachinger have found that magnesium appears to retard the motion of dislocations and, furthermore, they find little or no effect of magnesium on the size of subgrains formed during high temperature deformation. In view of the apparent contradictions as to the effect of magnesium on subgrain size, the recovery process in Al-Mg alloys has been investigated more thoroughly by studying the annealing out of X-ray line broadening, hardness, and electrical resistivity from alloys cold worked at room temperature. Material Used—The chemical analyses of the alloys are given in Table I. Fabrication—The material used was cold rolled 20 pct at room temperature, the grain size prior to the last cold rolling operation being similar to that used in previous work; i.e., 230. The experimental procedure for annealing, determination of X-rav half-veak breadth. hardness measurement, electEica1 resistivity, and density and metallographic examination was exactly the same as previously described." Variation of X-Ray Half-Peak Breadth with Annealing Time—Isothermal annealing curves at 100°, 200°, and 250°C were obtained for material cold worked 20 pct. The half-peak breadth of the (333) Ka, line directly after cold working is shown as a function of magnesium content in Fig. 1. Only with the 2.87 pct Mg alloy was overlapping of the a, and n.. reflections observed to any appreciable extent. To separate these, Rachinger's method' was used. Typical isothermal annealing curves are shown in Figs. 2 and 3 for 100" and 200°C, respectively. These curves are similar to those obtained previously for super-purity aluminum except that the

Jan 1, 1957

By J. D. Hunt, R. J. McDonald

It is proposed that extensive fluid motion occurs between the dendrites of a Partially solid casting and it is suggested the A segregates in steel castings are a direct result of this motion. The fluid flow arises because of density differences between liquid ahead of the dendrites and the interdendritic liquid. Experiments are described on a model system investigating this fluid motion. The importance of interdendritic fluid flow is discussed with reference to longitudinal segregation. SERIOUS macro segregation is often found in large killed steel ingots. Among the most common segregates are those known as A and V, Fig. 1. The A segregates are arranged over the surface of cones, the wide parts being at the base of the ingot. The A segregates are pencil like in shape and extend from the columnar into the equiaxed region. The V segregates are distributed over inverted cones but have a less well defined shape. They occur at the center of the ingot. Because of the commercial importance of macro inhomogenities these segregates have attracted wide-scale attention. The segregates contain alloying elements and impurities which depress the freezing temperature and are thus the last liquid to freeze. A number of explanations have been proposed to explain their presence. It has been suggested1'' that the segregates are the result of the equiaxed zone growing towards the columnar region together with the interaction of convection within the bulk liquid. It has also been proposed that the segregates are the result of nucleation and rapid growth ahead of the dendritic front.3 Neither of these explanations is completely satisfactory because A segregates are pencil shaped and are not found as continuous cones. In this paper an alternative mechanism is proposed, and experiments are described on a model system to determine whether the mechanism occurs in practice. It is thought that A and V segregates are not peculiar to steels but should occur in many other large castings. Fluid motion within the bulk liquid region of a casting has been extensively discussed. Little attention has been paid to fluid motion within the partially solid regions. The work415 that has been done has been mainly concerned with the fluid motion which results from the volume contraction on freezing. The volume contraction is used to explain various types of macro segregation. The present authors suggest that in many cases the fluid flow resulting from volume contraction will be small compared with that due to other causes. When the columnar region is growing, the liquid still remaining between the dendrites has a much lower temperature near the ingot walls than at the dendrite tips. The composition of the liquid in contact with solid will vary with temperature. The density of the liquid will thus vary both because of changes in temperature and composition. The layers of different density liquid will give rise to a slow but steady liquid flow through the interdendritic regions. If there is no density change with composition, the temperature gradient within the dendritic region should give rise to a downward flow between the dendrites, shown schematically in Fig. 2. When the liquid density changes appreciably with alloy concentration this motion could either be en-

Jan 1, 1970

By H. S. Drinker

THE first discovery of zinc 011 the property now worked by this company was made by the celebrated mineralogist, Prof. William Theodore Rapper, in 1845. Different claimants kept the property in continual litigation till 1861, when everything was satisfactorily settled by the purchase of the land by the company, who have worked it ever since. The mines are situated in a valley, four miles south of Bethlehem, Pa., in Lehigh County. The valley is from two to three miles broad, and is bounded 011 the north and south by syenitic hills. Syenite underlies the valley, and upon this is deposited the Potsdam sandstone, then a layer of slate, and, finally, a dolomitic limestone, belonging to the Chazy or Black River formation, in which the zinc deposits are inclosed. The rocks occur in folds, and have evidently been subjected to tremendous pressure from below, the zinc deposit being found in an anticlinal axis, in nearly vertical veins. I t is supposed that the zinc was originally disseminated through the

By K. P. Gupta, P. A. Beck, N. S. Rajan

By determining the a phase boundaries in the following ternary systems: V-Fe-Si (at 1175oC), V-Co-Si (at 1175°C), V-Ni-Si (at 1175oC), Cr-Mn-Si (at 1000°C), Cr-Co-Si (at 1175°C), Cr-Ni-Si (at 1175°C), V-Fe-A1 (at 1175°C) and Cr-Co-A1 (at 1175°C), it was found that Si exerts a stabilizing effect on these a phases, while A1 tends to destabilize them. Si atoms in solid solution occupy sites D in the a structure, The co/ao ratio increases with increasing Si-, Mn- or Fe-content. The volume of the unit cell decreases with increasing Si-content. THE stabilization of certain metal silicides (the Nowotny phases) by the addition of relatively small

Jan 1, 1961

By John Hays Hammond

The Transvaal comprises about 120,000 square miles (nearly • the size of the United States Territory of New Mexico). Besides the famous Witwatersrand, which will here be de scribed in detail, there are two quartz-mining districts of some importance, viz., Lydenburg and De Kaap. The Lydenburg district first attracted attention in 1876, when the alluvial deposits of that section began to be exploited. At a later period vein-rnining was started, and at the present time several companies are operating in that district. The product in 1898 of five companies, running 137 stamps, was 154,560 tons of ore, yielding 108,884 crude ounces of gold (an average of 14.09 dwt. crude gold per ton) valued at £392,378. The De Eaap gold-fields were discovered in 1884. In 1898, seven companies, running 200 stamps, produced 89,760 crude ounces of gold, valued at £314,792. I. Mining Titles in the Transvaal. The mining laws of the Tranuvaal are most excellent in char acter, and while the claims cover every square foot of land for an area of nearly 40 miles long by from 2 to 3- miles wide, there have been practically no conflicts over extra-lateral rights. Notwithstanding the change in the political status of the Transvaal likely to follow the present war, it may be coufi dently assumed that the main features of the mining law of the South African Republic will be retained, and certain op pressive featureu of monopolies, etc., bearing with special weight on the mining industry, will be abolished. The dynamite mo nopoly was one that bore most heavily on the mining industry; and, according to the Reports of the State Mining Engineer, explosives, including fuse and detonators, amounted to nearly 10 per cent. of the total working costs of the mines. Further more, it was impossible to obtain the proper quality for the most economical working, and often 80-per-cent. or 40-per-cent. gelatine had to be used- in many instances where 60-per-cent.

Jan 1, 1902

By B. M. Larsen, W. E. Shenk

This paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable —that is, the time interval between successive reversals—should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one lLminimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: I. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potenti-ometric control instrument, to correct any tendency toward temperature unbalance between ends of the furnace. 3. A second "maximum temperature

Jan 1, 1945

By B. R. Banerjee

MATERIAL used throughout this investigation was high-purity aluminum (99.998 pct). The 1/2-in. cubes were cut out of a cold-rolled slab and annealed at 550°C for 1 hr before deformation. The single crystal specimen was 1 in. in diam x 0.33 in. thick, cut from a cylindrical crystal produced by cooling at about 55°C per hr in a furnace which had a convenient gradient of about 10°C in every 4.5 in. vertical crucible length. Specific data on the ten specimens studied are summarized in table I. Three types of deformation were employed: (I) compression in a hand-operated hydraulic press; (2) impact with a 7-lb sledge hammer; and (3) rolling, using a wedge-shaped specimen' to obtain a gradient of deformations varying from 0 to 50 pct along the length of the wedge. Specimens were either deformed at room temperature, or first cooled in a freezing mixture of dry ice and ether at a temperature of —72°C and then deformed between steel blocks cooled with dry ice. The specimens deformed at the low temperature were ground and polished through 000 emery paper and wheels impregnated with alundum and alumina No. 1. During this entire procedure the specimens were dipped frequently in the freezing mixture of dry ice and ether in order to maintain constantly a frosty surface as insurance against overheating. All specimens were given a final electrolytic polish, using two different electrolytes* to insure that the surface effects observed were not char- acteristic of the polishing technique. With both electrolytes, the annealed specimens gave even surfaces with good polish. Several standard etchants were tried without success. The best results were obtained with an immersion etchant, developed in this connection, containing: hydrofluoric acid, 4 parts; nitric acid, 1 part; glycerine, 3 parts. Discussion of Results Typical strain markings have been observed within deformation bands, as shown in figs. 1, 2, and 4. By stereographic plotting of metallographic measurements, the strain markings within a deformation band in a single crystal of aluminum deformed by compression were found to be traces of (111) planes within a maximum scatter of 6". The edges of the deformation band were found to be traces of the (100) planes also within the maximum scatter of 6" (in agreement with previous workers). At 30 pct deformation, this scatter was considered quite normal because of the fragmentation and rotation of the crystal. This solution, based on the traces on one plane of observation is not unique, but as the planes were observed to be those normally and logically to be expected, further work in this regard was not felt to be necessary. The study of strain markings in a wedge-shaped specimen, rolled to obtain a gradient of deformation from 0 to 50 pct, revealed prominent strain markings at 25 pct reduction in thickness (fig.5). Faint and weak strain markings were visually observable up to a minimum reduction in thickness of about 12 pct. Since strain markings have been observed in other face-centered cubic metals after much smaller deformations;1, 2 and since the rate of recovery in aluminum is high, it is believed that, at lower deformations, self-recovery removes the localized strains at the slip interfaces, thus removing the source of the etching effects that give rise to strain markings. At high magnifications, strain markings sometimes seem to appear as very thin, light-banded re-gions bounded by a pair of dark edges. This so-

Jan 1, 1951

By Frederick N. Rhines, Robert F. Mehl

IT has been shown elsewhere1 that the data on the rates of diffusion in solid metals are fragmentary and in many cases unacceptable. As a result, relatively little is known concerning the factors determining rates of diffusion and the variations in these rates with temperature. The first form of Fick's law (equation 1 below), ‡ in which the diffusion coefficient D is assumed invariant with composition, has been recognized for many years as only an approximation. The differential equation representing the second form of Fick's law (equation 4 below) has only recently been integrated by Matano,2 and unfortunately only in cases where a full diffusion-penetration curve (concentration-distance curve) has been obtained can the Matano solution be applied. The proper analysis of diffusion data is thus confined to the data of Grube and Zedele and of Zedele.§ These data are essentially for one temperature alone and do not furnish any information on the variation of the activation heat of diffusion, Q, with concentration: no information exists on the variation of Q with concentration within a singles olid solution field. 11 Much of the argument concerning the properties of metals that determine D and Q has been drawn from data in which variations of the quantities with concentration are unknown, for these data have been taken from experiments that could not furnish this information. Speculation concerning the properties of metals that may be effective in determining D and Q on the basis of data in which the chosen D and Q values are averages over wide concentration ranges of values at particular concentrations, ranges often of 100 per cent, is likely not to be fruitful.

Jan 1, 1938

By R. N. Upadhyay, M. Maleki, I. Fatt

Conventional laboratory core analysis tests on samples of two limestone reservoir rocks indicate that about 20 per cent of PV is in dead-end pores. These tests (electric logging formation factor, mercury injection capillary pressure and miscible displacement) were carried out on 1/4-in. diameter test plugs. Test results show a clear dilference between these samples and sandstone or homogeneous limestone reservoir rock. Although the amount of dead-end pore space can be only roughly estimated, the presence of such pore space seems clearly indicated. Pressure transient studies also show presence of deadend PV. Although they do not give quantitative results, pressure transient data yield a reasonable estimate of the size of the neck connecting dead-end pores to the main flow channels. INTRODUCTION Equations conventionally used to describe reservoir flow behavior contain the implicit assumption that all connected pore spaces contributed to both porosity and permeability. Several authors3-7 have pointed out the changes in pressure transient behavior and in electric log interpretation that may result if this assumption is incorrect and, instead, dead-end or cul-de-sac pores are present. There is a need for laboratory tests that can detect presence of dead-end pores in core samples. With such information on hand the petroleum engineer can make more rational use of the mathematical tools now available for analysis of reservoir flow behavior. This paper describes laboratory studies designed to detect and, if possible, give a quantitative measure of dead-end PV in laboratory-size core plugs. Three reservoir rocks were used, two of which were limestones suspected of having deadend pore spaces and a well-known sandstone, used as a comparison standard, in which there is believed to be little or no dead-end pore space. All the studies were designed to measure the natural dead-end PV; i.e., the pore space which is dead-ended because of rock structure. During multiphase flow in a rock without dead-end pores, some parts of one of the phases can become surrounded by the other, thereby giving (for certain flow behavior) an effective dead-end pV8,9. Such behavior will not be described here.

Jan 1, 1967

By Thomas Wilson

IN a single-crystal cube of iron the arrangement of the atoms is that characteristic of iron at room temperature: the body-centered cubic lattice. X-ray investigation has shown this structure to be characteristic of iron, as it has shown the atomic arrangement of other metals to be characteristic of those metals also. Rarely do substances have more than one characteristic atomic arrangement. Many physical properties of metals are directly connected with their atomic arrangements, so that changes of arrangements produce changes of properties. Only chemical change influences atomic arrangement. If a difference in the physical properties of a metal is caused by a process which involves no chemical change, the cause of the difference in properties must be sought elsewhere than in the atomic arrangement. Frequently this cause can be traced to alteration of crystal orientation. The orientation of a crystal may be defined as the relationship which the crystallographic axes bear to some quantity of reference. A cube of iron appears cubic whether it is regarded from a face, an edge, or a corner. Yet these three positions represent three different orientations of the cube with respect to the observer. It is evident that the orientation of this cube of iron, unlike the atomic arrangement, is not characteristic of iron but is entirely dependent on the previous history of the cube. Most of the processes of metal working, such as wire-drawing, rolling, and bending, change the orientation of the crystals present in the worked metals. These processes usually tend to produce rotation of the crystals into positions approaching a mean. Specimens of metals show-ing this characteristic are said to possess a preferred, orientation. Tensile strength, ductility, and many other properties are influenced by orientation changes; therefore two specimens of the same metal may show different values of these quantities. In metal specimens possessing a narrowly limited preferred orientation, these quantities will vary in magnitude in different directions throughout the specimens. The investigation of the influence of manufacturing operations upon crystal orientation, and hence upon physical properties of metals, is an important

Jan 1, 1929

By Eizo Yabuuchi, Yukito Imanaga

INTRODUCTION In treatment of mine drainage, it is well known that the neutralization by calcium carbonate is far better than by slaked lime because of cheaper cost and better precipitability of its deposit. However, in case of iron ion contained in the mine drainage consists of ferrous salt, the ferrous salt must be oxidized to ferric salt before neutralization, because the ferrous salt does not react with calcium carbonate. At Yanahara Mine, during the period of 1950 through 1956, ferrous ion in the mine drainage had been oxidized to ferric ion, simultaneously neutralized by adding calcium carbonate into the aerated drainage. During the period of 1961 through 1974, after passing through many kinds of treating methods, the neutralization had been carried out by addition of calcium carbonate into the drainage after oxidized its ferrous ion to ferric by using nitrous gas as an oxidizing catalyzer. Meanwhile we had made an experiment on the oxidation of ferrous ion by utilizing iron bacteria, and developed a method which oxidized ferrous ion in large quantities briefly by cultivating and concentrating iron-oxidizing bacteria. Since 1974, we have been operating successfully for treating the drainage at Yanahara Mine by means of utilizing these bacteria.

Jan 1, 1976

By D. B. Crouch, D. A. Poulter

The engineering and metallurgical assessment of the McLaughlin Project ore body concluded that an open-pit mine and cyanide leach mill process would be feasible, producing both waste rock and residual mill tailings. As a part of the planning and permitting process, site selection studies were conducted for the tailings and waste rock disposal. The site selection process began with a regional identification of potential disposal sites and proceeded through 1) regional screening, 2) elimination of sites with obvious fatal flaws, 3) qualitative ranking of site evaluation criteria, 4) quantitative ranking of sites, 5) field investigation, 6) evaluations of field data, and 7) selection of preferred sites. Based on this approach of site rankings and field evaluations, tailings and waste rock disposal sites were selected and recommended for the preliminary design phase of the permitting and project development process. The site selection study provided the documentation necessary to justify the use of these sites for waste disposal and enabled Homestake Mining Co. to anticipate and integrate environmental concerns with agency requirements into the planning process.

Jan 1, 1986

Many definitions have been advanced and many limitations advocated in the use of the terms, veins, lodes and ledges. The following definitions appear to follow the best usage. [ ] A fissure vein, according to Lindgren, is a mineral mass tabular in form as a whole, though often irregular in detail, filling or accompanying a fracture or series of closely set and intimately related parallel fractures in the enclosing rock, the mineral mass having been formed later than both the country rock and the

Jan 1, 1932

By Edward Martinez

Although the copper segregation process has been known as a method for treating oxide copper ores since the 1920's, the reactions involved in this process are still a matter of conjecture. However, the evidence turned up in a recent series of experiments at Asarco's Central Research Laboratories strongly indicates that some of the proposed reactions may not be occurring. Experimental work on oxide copper ores from the Sagasca mines in Chile led to the discovery of the copper segregation process in 1923. It was found that the reduction of the copper with coal at about 700°C occurred on the surface of the coal instead of remaining disseminated in the ore. The unusual behavior of the copper, which caused it to migrate from the ore particles to the coal, was traced to the presence of a small quantity of sodium chloride occurring in the ore. Further experiments with oxide copper ores proved that the presence of a halide, either occurring naturally or admixed with the ore, caused the copper to migrate from the ore particles and to segregate in the charge.

Jan 8, 1966