Search Documents

By W. N. Carr, J. R. Biard, B. S. Reed

An analysis of the semiconductor injection laser is presented which is based on a phenomenological model using device and material parameters. The intent of the laser threshold analysis is not to predict from theory the actual threshold current density but rather to provide a logical means of interpreting experimental results. The device and material parameters have been selected such that they describe both the threshold conditions and quantum efficiency of the lasev. A technique is proposed whereby the current required to obtain a population inversion is predicted from device 1-V characteristics. Experimental data are presented which support the analysis. THIS investigation is concerned with the characteristics of GaAs lasers fabricated in this laboratory. However, the assumptions used in these calculations should not limit their application to GaAs alone. It is felt that the analysis is sufficiently general to be useful in describing the operation of other semiconductor-laser materials. ANALYSIS heavily doped semiconductors to be considered. The absorption and/or generation of optical radiation may be completely specified in terms of q(E) and the probability functions f,,(E) and f,(E) which define the occupancy of the valence-band and conduction-band levels, respectively. The symbols used in this analysis are listed at the end. Following the approach of all' it can be shown that the effective gain coefficient, g, in the plane of a forward-biased P -N junction is g(E)=-ai@)[1-fv(E)-fc(E)] [1I In particular Eq. [I] holds for the photon energy at which lasing occurs, Ep. Throughout the following discussion Eq. [I] is considered only for the lasing transition E = Ep. For simplicity the functional energy dependence of the various factors is omitted in subsequent equations. Unless otherwise stated the symbols used represent the values at Ep. If the analysis is limited to the P-type side of the laser junction, the function q(l -f,,) is recognized as the band-to-band absorption in the P-type material at thermal equilibrium. Under forward-bias conditions the function f, is determined by the electron quasi Fermi level in P-type material. For sufficiently large forward bias the second term in Eq. [3] will become dominant and net gain will result; i.e., g will become positive. In order to simplify the subsequent analysis several assumptions are in order at this point. a) No conductivity modulation occurs. /„ is independent of f, and therefore go is a constant. b) The P-type material is heavily doped such that the degeneracy of the valence band permits popu-

Jan 1, 1964

By H. R. Stahl

FIVE mills are operated in Southeast Missouri by the St. Joseph Lead Co.; these have a total rated capacity of 24,300 tons per day divided as follows: Federal, 12,000 tons; Leadwood, 4800 tons; Desloge, 3600 tons; Bonne Terre, 2400 tons; and Mine La Motte, 1500 tons. These concentrators are similar in a general way, differing mainly in size and type of equipment and in minor variations in flow sheet. No attempt is made rigidly to standardize procedure in the various mills in spite of a general similarity in the ores. Each mill may be regarded as a separate laboratory in which new ideas and changes may be tried. A generalized description of the process is given, noting important differences in procedure at the various plants. The concentration process may be divided into five main stages: dry crushing, wet grinding, desliming and classification, tabling, and flotation.

Jan 1, 1947

By J. E. Breen, J. Weertman

The creep rate of polycrystalline tin was studied as a function of temperature and stress in constant stress experiments. The temperature was varied from room temperature to almost the melting point of tin. Activation energies were calculated from tests run at the same stress. It was found that on a log creep rate vs inverse temperature plot the experimental points did not fall on one straight line but on a line which changed its slope in the 90° to 160°C region. Two activation energies for the creep of tin can be calculated from the data: a value around 26,000 cal per mol at high temperatures and a value around 11,000 cal per mot at low temperatures. It is suggested that the discrepancies between the creep activation energies and those of self-diffusion can be accounted for if self-diffusion takes place predominately by Zener's ring mechanism rather than through vacancy or interstitial movement. SHERBY, Orr, and Dorn' and Dorn' have recently reviewed some of the data on high temperature creep of metals. -The data show that the activation energy of high temperature creep is approximately equal to the activation energy of self-diffusion. This same correlation has also been successfully made between the activation energy of grain boundary relaxation and that of self-diffusion.3,4 The metal tin does not fit into this simple picture. Its activation energies of self-diffusion differ appreciably from that of grain boundary relaxation and of creep. Fensham,5 from a precisely performed experiment, has determined that the activation energies of self-diffusion of tin are 10,500 and 5,900 cal per mol along the C and A axes, respectively. There are two energies because of the anisotropic nature of tin. Rotherham, Smith, and Greenough6 have shown that the grain boundary relaxation activation energy is 19,000 cal per mol (measurements made from room temperature to 100°C). Puttick and King7 found the same activation energy for grain boundary slip in bicrystals of tin (180° to 225°C region). Until recently, there was no high temperature large strain creep data on tin suitable for activation energy calculations. At rather small strains (up to 0.01), Tyte8 had made a series of measurements on tin from which activation energies can be calculated. In Fig. 1 are plotted some of his data on a log creep rate vs inverse temperature graph. It can be seen that Tyte's work indicates that at a relatively low temperature the activation energy is around 7,400 cal per mol but at higher temperatures the activation energy increases. Since Tyte measured the creep only for small strains, it is doubtful if a

Jan 1, 1956

By Lester Guttman

The connection between short-range order and thermodynamic activities in binary solid solutions has been pointed out by Birchenall1 who calculated approximate values of the energy of interaction of Zn and Cu and of the degree of short-range order in alpha-brass at one composition and two temperatures. The purpose of this note is to call attention to a somewhat more accurate theory than that used by Birchenall and to extend the calculations to a wider range of temperatures and compositions as a means of testing its applicability. This is an example of the well-known general method of comparing measured thermodynamic functions of a system with those calculated from a microscopic model by means of statistical mechanics. In this case, mathematical approximations must be used which make difficult any decision about the validity of the model. Birchenall's statistical method resembles closely that calletl by Fowler and Guggenheim2 the "quasi-chemical" method which has been shown to lead in certain cases to results identical with those obtained by the method of Bethe.3 The quasi-chemical method has been extended by Takagi4 to give general formulas for the free energy of binary solid solutions based on several lattices at all compositions and temperatures. Specifically, he treats the four systems typified by: I. ß—brass; 2. a— brass; 3. AuCus; 4. AuCu. When the temperature is so high that no long-range order exists, these formulas reduce to the same form for all lattice types, namely: F - FO = (E - EO) - T(S - S°) = ½N(c — x)(2vAB — vAa - Vbb) + M1/2KTzN[x log x + 2(c - x) log (c - X) + (I - 26 + X) log (1 - 2c + x)] -kT(z - I)N[c log c+(I-c) log (I -c)] Eq 1 Here the symbols have the following meanings: F—Helmholtz free energy E—nergy 5—ntropy k—the gas constant per molecule z—coordination number, (e.g. I2 in a-brass). N—total number of atoms c—atomic fraction of A Vaa, vbb, vab—nergy per bond of the corresponding bonds log means log, throughout The superscript ° denotes the thermodynamic fuliction in the standard state, which has been chosen to be pure A or B with the same crystal structure as the solid solution. The quantity x is the ratio of the number of A-A bonds to the total number and for minimum F satisfies the equilibrium condition Vaa + Vbb — 2Vab _ (c — x)2 kT l0g x(i - 2C + x The free energy may also be written in terms of /La and B, the chemical potentials or partial free energies per alom:

Jan 1, 1949

By Lester Guttman

The connection between short-range order and thermodynamic activities in binary solid solutions has been pointed out by Birchenall1 who calculated approximate values of the energy of interaction of Zn and Cu and of the degree of short-range order in alpha-brass at one composition and two temperatures. The purpose of this note is to call attention to a somewhat more accurate theory than that used by Birchenall and to extend the calculations to a wider range of temperatures and compositions as a means of testing its applicability. This is an example of the well-known general method of comparing measured thermodynamic functions of a system with those calculated from a microscopic model by means of statistical mechanics. In this case, mathematical approximations must be used which make difficult any decision about the validity of the model. Birchenall's statistical method resembles closely that calletl by Fowler and Guggenheim2 the "quasi-chemical" method which has been shown to lead in certain cases to results identical with those obtained by the method of Bethe.3 The quasi-chemical method has been extended by Takagi4 to give general formulas for the free energy of binary solid solutions based on several lattices at all compositions and temperatures. Specifically, he treats the four systems typified by: I. ß—brass; 2. a— brass; 3. AuCus; 4. AuCu. When the temperature is so high that no long-range order exists, these formulas reduce to the same form for all lattice types, namely: F - FO = (E - EO) - T(S - S°) = ½N(c — x)(2vAB — vAa - Vbb) + M1/2KTzN[x log x + 2(c - x) log (c - X) + (I - 26 + X) log (1 - 2c + x)] -kT(z - I)N[c log c+(I-c) log (I -c)] Eq 1 Here the symbols have the following meanings: F—Helmholtz free energy E—nergy 5—ntropy k—the gas constant per molecule z—coordination number, (e.g. I2 in a-brass). N—total number of atoms c—atomic fraction of A Vaa, vbb, vab—nergy per bond of the corresponding bonds log means log, throughout The superscript ° denotes the thermodynamic fuliction in the standard state, which has been chosen to be pure A or B with the same crystal structure as the solid solution. The quantity x is the ratio of the number of A-A bonds to the total number and for minimum F satisfies the equilibrium condition Vaa + Vbb — 2Vab _ (c — x)2 kT l0g x(i - 2C + x The free energy may also be written in terms of /La and B, the chemical potentials or partial free energies per alom:

Jan 1, 1949

By E. A. Gulbransen, W. S. Wysong

The behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance. The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotec-tive nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance studyl, 2 of the following problems: (I) the oxidation kinetics in the temperature range of 250°to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films; and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 2 50°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide Moo3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics: time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation. The general interpretation of many of these factors has been previously discussed. Literature The oxidation of molybdenum has not been studied critically. Although many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Gulbransen." Their results showed that Moo2 is the oxide which is stable in contact with the metallic substrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Moos is no longer observed, MoO2 being the only oxide found. Hagg and Magneli6 have shown from an X ray study that the a-phase, orthor-hombic Moo3 is stable up to 1050°C. Two other phases, ß and ß with compositions close to MoO2.90 are also obtained. The formula for the 0 phase is not given but that of the ß phase is defined as Mo9O26 The 0' phase is found to be built upon a monoclinic unit cell. A ?-phase is isolated from a preparation MoO2.75 heated for 17 hrs at 670°C. This phase is

Jan 1, 1949

By R. I. Jaffee, H. P. Nielsen

In recent years much attention has been given to high melting alloy systems. It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. Past Work Miillerl determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from I771 C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Miiller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and Jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at I000 C. Vines and WiseS report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. Materials The platinum powder used in this work was kindly supplied by the Research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio. It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HC1. The resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1949

By Herluf P. Nielsen, Robert I. Jaffee

IN recent years much attention has been given to high-melting alloy systems, It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. PAST WORK Müller1 determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from 1771°C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Müller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at 1000°C. Vines and Wise3 report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. MATERIALS The platinum powder used in this work was kindly supplied by the research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio, It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HCI. the resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1948

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni, 16 per cent Cr, 35 per cent Ni, 12 per cent Cr, 60 per cent Ni, etc ) in recent years has been accompanied by continued demands by the consumer for improvement in properties The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper† The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure The creep-test laboratory constructed for the American Brake Shoe and Foundry Co is designed to permit 1000-hr tests in the temperature range of 1200° to 2200°F with a choice of applied stress extending from 50 to 50,000 lb per sq in in increments of 50 lb per sq in To simplify the calculation of weight combinations, the loading beams (Fig I) are provided with counterweights to eliminate the tare The precision of the knife-edges (10 1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle Check of the loading weights proved the maximum error to be 0 06 per cent Axial alignment is provided by crossed knife-edges in the grip seats The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U S Steel Corporation An 80 per cent Pt, 20 per cent Rh No 19 B and S gauge wire is used as the heating element The details of construction are shown in the radiograph reproduced in Fig 2 The windings are held in place on an alundum tube with alundum cement, the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F over a 4-in gauge length (Fig 3) To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

Aamot, Olav Crone, Chem. Engr., Elektrokemisk Raadhusgt..23, Oslo. Norway. '29 Abadilla, Quirico A., Dir., Bureau of Mines Manila, P. I. '3S Abbott, Clarence E., V.P., Charge of Raw Materials, Tennessee Coal, Iron & R.R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abel, Raymond L.. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '2S Abel, Walter D., Div. of Corporations Los Angeles, Calif. '32 Abele, Louis T., U. S. Corps of Engrs 7211 Glen Oak Ave., Baltimore. Md. '31 Abel], Leo M., Research Met., Mount Morgan Ltd Mount Morgan, Queens.. Australia. '31 Abenius, Hakan V c/o Falu Gruva, Falun, Sweden. '37 Abernathy, G. E., Geol., Kansas State Geol. Survey Pittsburg, Kan. 3S Aborn. Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abrams, Charles Jackson 1624 17th St., Denver, Colo. '3 t. Abstein. Henry T., Engr. & Mgr., Profile-Tamarack Mines CoYellow Pine, Idaho. '27 Acker, E. O'C., Met L28 East Washington Lane, Germantown, Philadelphia, Pa. '86 Ackerman, D. E., Met., Assoc. Prof. of Met., Purdue Univ Lafayette, Ind. '35 Ackerman, E. Dumont, Sub-Surface Geol., Temblador Camp, Standard Oil Co. of Venezuela, Caripito, Venezuela. '3S Ackerman, George F.,. Div. Foreman. The Fresnillo Co Fresnillo, Zac., Mexico. '36 Adami, A. F., V.P. & Prof. of Min. Engrg., Montana School of Mines Butte, Mont. '19 Adami, Charles J., Min. Engr 99 S. Downing St., Denver. Colo. '12 Adams, Army, Cons. Engr 714 W. Main St., Grass Valley, Calif. .'37 Adams, Clyde B.. Geol.. Socony-Vacuum Oil Co., Inc 26 Broadway, New York, N. Y. '39 Adams, Ernest C., 6th Engrs Fort MacIntosh, Laredo, Tex. '35 Adams, F. J., Gen'l Agent, Gulf Production & Pipe Line Cos Fort Worth, 'lox. '29 Adams, F. S., Supt., Power Dept., Anaconda Copper Min. CoAnaconda, Mont. '37 ADAMS. FRANK DAWSON, Hon. Mbr., 1913; Logan Prof. of Geology and Dean, Faculty of Applied Science. McGill Univ., Montreal, Que., Canada. '13 Adams, Gale L., Supervisor, Process & Dev. Lab., General Pet. Corp. of California, Higgins Bldg., Los Angeles, Calif. '18

Jan 1, 1939

By John V. Beall

Never having done it before, it took us all day and until 11 at night to select and pack for a four-day back- pack trip up Lake Chelan last month. When we were through, we couldn't lift our own pack and Sylvia's, OUT spouse's, we barely managed to budge. Nevertheless, the next morning we were at the dock to board the Laldy of the Lake for the 3 ½ -hr boat trip to Lucerne. Our dress and accouterments creating the appearance of a veritable expedition into the wilderness made a sharp contrast with our fellow passengers, a senior citizens tour group from Spokane. We had come out to Seattle for the SME Fall Meeting and were taking advantage of the occasion for a vacation trip back to Lucerne and Holden where we had lived briefly 25-years ago, and a backpack trip up Railroad Creek from Holden to the Glacier Peak country, weather permitting. No matter what you say, weather is important, and this is one of the ingredients that went into making the SME Fall Meeting and Exhibit in Seattle, September 22-24, a thoroughly delightful experience for the 700 plus persons who attended. Seattle is a beautiful city, but with late September sunshine, which we experienced, it is the best. The second ingredient, is a swinging host committee. Under the leadership of Don Anderson and Tom Van Zandt, co-chairmen, and Mrs. Cecilia Reed, Ladies Program, superb hospitality and fine arrangements were blended. Earl Beistline, from Fairbanks, organized a two-day short course on arctic operations which preceded the meeting and drew an attendance of 44. Dick Robbins, in charge of arrangements, provided Masters-at- arms for technical sessions and a presentation of the colors by the U.S. Coast Guard at the Welcoming Luncheon. Eric Cheney's field trips ranged far and wide with events both before and after the meeting. David (Jeff) Kroft, capably managed audio-visual operations with a group of students from the University of Washington. Charles Hochmuth worked long, hard and effectively before and during the meet- ing on finances. Hank Reed, managed an authentic three-ring circus as Entertainment Chairman. His activities covered two cocktail receptions for all registrants and a dinner-dance. Dolph Campbell and Joe Hackbarth provided publicity by press and TV (see p. 37-40). SME's meetings have certain characteristics and possibly not all of these are known to everyone. The first of these is the deliberate involvement of the AIME Section in the area of the meeting. Most trade shows and conventions are run 100% by a professional staff and although SME staff could also do this, it has been our experience that a more friendly and better meeting results when the local members apply their talents. Actually SME only considers a site for a meeting after it has received an invitation from a Section. The knowledge of local conditions which Section committeemen bring to a meeting is of great value.

Jan 1, 1971

By ROBERT. RICHARDS

I. INTRODUCTION The object of this paper is to enlarge the field of settling velocities treated by me in my former papers, Close Sizing Before Jigging, and Sorting Before Sizing.' There seemed need of work both on coarser and on finer sizes. Messrs. A. Sidney Warren and M. L. Nagel undertook the investigation for the coarser sizes, from 12.85 mm. down to 2.05 mm. diameter. Their work, because of the closer spacing and because of the increased number of observations and consequent stronger averages, called for a revision of the former work. Messrs. G., A. Barnaby and Ralph Hayden undertook this part of the work, from 2.49 mm. down to 0.28 mm., which is near the limit of sifting. Their work covers the ground much more minutely and comprehensively than the former papers. There remained to be covered the portion of the field too fine for investigation with the sieves. This part, covering the range of grains from 0.48 to 0.03 mm., was undertaken by Mr. E. S. Bardwell. For it he used the elutriation method. II. THE FIRST, OR COARSEST, SECTION OF THE FIELD. The first desideratum in this investigation was a series of sieves for sizing the sands preparatory to making the tests. It became necessary, therefore, to decide on a sieve-scale for this purpose. A sieve-scale is a series of sieves in which the dimensions of the holes of the successive members form a series increasing by a. definite ratio. There are three natural sieve-scales : 1, progressing by doubling the width of the hole for each suc-

May 1, 1907

By M. L. Requa

EVERY forward step in civilization brings with it an increase in population and increasing demand for raw materials. Modern civilization, because of its industrial development, depends more and more for its well-being on ample supplies of raw materials; the higher the type of that civilization, the greater its dependence. No fact is more obvious than that the raw materials should be put to use with greatest prudence and efficiency. National life is not a matter of a decade or a century. Conservation is no longer a matter for political discussion; it is a vital element in the future welfare of all nations. Unfortunately, to the minds of many, conservation means the locking up of natural resources, their arbitrary withdrawal, bringing about, in short, a condition of industrial stagnation. This has occurred in past centuries through misdirected governmental effort. Two eminent engineers have variously defined conservation as follows:

Jan 1, 1925

By T. W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (water box) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 % reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2012

By James R. Finlay

SOMETIMES the American Institute of Mining and Metallurgical Engineers appears to be a strictly technical society, and if so my paper should deal with the technical operations of finding and producing gold. But I have not been engaged in practical gold mining since 1910. What I have been doing mainly for the last 25 years is to try to figure out what the income of a mine-gold, or any other-would be worth to an investor. So I have been in contact with gold mining, in one way or another, for some 42 years. I say that with a purpose. In that time the industry has been through one of its cycles. The value of gold mines is very dif¬ferent at different points in one of these cycles. For this reason the cycle of gold mining is a highly practical study. The cycle of gold is a more or less rhythmical change in its value or purchasing power measured in the grand average of other commodities, which is the same thing as its price. Taking the price of gold in 1897 as a stand¬ard, a dollar at that time declined to 55c. in 1913, to 26.8c. in 1920, and since then it has risen to 47.4c. in 1930 and to about 64c. in 1932. It is worth about 21/ times as much now as it was in 1920, but less than two¬thirds as much as in 1897. When this change is applied to the value of a gold mine still greater differences are evident. The cost of producing gold is of course measured in labor and other commodities, and as that cost goes down the margin of profit measured in the gold itself increases. Thus a mine which might make only 10 per cent profit in 1920 on its gross output may easily make 25 per cent now. The stockholder gets 2 ½ times more gold that is worth 2 1/2 times as much in purchasing power, therefore the real value of his holding has risen by the one factor multiplied by the other, giving him 61/4 times as much goods or services as he had in 1920.

Jan 1, 1933

By Carl Lee

CHICAGO in the last week of June fulfilled all its promises to the visiting engineers except one. This holds true with respect to the activities of the Regional Meeting of the A. I. M. E. in particular and of Engineers' Week in general. No one expected to find much of the beautiful in the outward aspects of the Fair-the Century of Progress Exposition, to be more formal; but they expected novelty, color, and startling lighting effects at night, and they were in no sense disappointed. It has been said that the architecture is a portent of the style of the buildings of the future; most who have seen the Fair hope that this forecast will prove inaccurate. As to the exhibits themselves, they are splendid. They are in keeping with the theme of the Exposition-a Century of Progress in science, in engineering, in the industries based upon them. No attempt will be made here even to suggest the exhibits that are most interesting. There are plenty for every one; and any member of the Institute who has the opportunity should by all means visit Chicago before the end of October.

Jan 1, 1933

By L. T. Larson

The spectral reflectivity of zirconium in light of 441 to 668 nanometers (nm) wavelengths and air immersion has been determined. Bireflectance and apparent-angle -of-rotation measurements show zirconium to be optically isotropic when examined in light of approximately 484 nm wavelength. There is a direct relationship between bireflectance and the tilt of the basal pole of zirconium from the surface normal. This relationship allows the determination of the spatial orientation of the basal pole of an individual single crystal within a coarse-grained poly crystalline section to within± 2 to 3 deg for angles of basal pole tilt from 0 to 90 deg. In recent years considerable attention has been given to the quantitative determination of optical properties of opaque minerals by use of vertically incident, plane-polarized light. In particular, Cameron' and Cameron et a1.2 have developed criteria for the identification of a large number of anisotropic ore minerals based upon measurement of the apparent angle of rotation and the ellipticity or phase difference of the reflected light. It was shown by Larson and Pickle-simer3 that apparent-angle-of-rotation measurements may also be used to determine crystallographic orientations of grains of noncubic metals. In particular, it was shown that the basa.1 pole orientation in space of zirconium grains can be determined to ±3 deg for those grains with basal pole tilts of 10 to 90 deg from the plane of the section. Another, even more widely studied, optical property is reflectivity. cameron4 has commented upon measurement of the reflectance of plane-polarized, vertically incident light and Bowie and Taylor5 have made such measurements an integral part of their system of ore-mineral identification. Leow6 has reported on the spectral reflectivity of molybdenite and has used reflectivity values to calculate refractive indices and absorption coefficients. Cameron7 has made use of reflectivity values to ascertain aniso-tropic ore mineral symmetry and Piller and v. Gehlen8 have evaluated sources and importance of errors in reflectivity measurements as applied to calculation of optical constants. cambon9 has shown that reflectivity measurements using vertically incident, plane-polarized light are useful in the investigation of metals and in the identification of phases present in alloys. Bronson10 has made preliminary measurements on the optical anisotropy of beryIlium and Mott and Haines11 have published qualitative data on the intensity of light reflected from sections of bismuth, tin, and aluminum when these metals are microscopically examined under crossed polarizing plates. Koritnig12 has correlated the reflectivity of homogeneous solid solutions with their chemical compositions. From the above work and investigations in progress by this author, it is apparent that accurately determined values for the reflectance of vertically incident, plane-polarized monochromatic light from carefully polished surfaces of noncubic metals can prove useful in identification, composition determinations, and crystallographic orientation applications. Finally, reflectivity values, when measured in two media of differing refraction index and related to standards whose spectral reflectivities in these media are known, can be used to calculate optical constants such as refractive index and absorption coefficient. These constants may prove of use to those concerned with problems of electron band configuration. This paper reports the spectral reflectivity of zirconium measured in light of 441 to 668 nanometers (nm) wavelengths and air immersion. It also gives maximum bireflectance values for a prism section of zirconium in these wavelengths and shows how bire-flectance may be used to determine the crystallographic orientation of zirconium single crystals. Because of the lack of information on the reflectivities of the standards in oil immersion, no attempt is made to calculate the refractive indices or absorption coefficients although it is recognized that such values may be of fundamental importance. METHOD Single crystals of zirconium were cut by electro-discharge machining from a single-crystal rod grown from iodide bar by an electron-beam zone-melting process.13 The crystal sections were mounted in cold-setting epoxy resin and mechanically polished to a plane, uniform, bright surface. Each crystal was then chemically polished in a 26/26/43/5 mixture (by vol) of water, nitric, lactic, and hydrofluoric acids to remove the mechanically damaged and smeared surface layer. Final polish was obtained by electropolishing at 30 v in a bath of methyl alcohol and perchloric acid (98/2 by vol) at -70oc.14 Reflectivity measurements were made using a photometer system designed and developed at Oak Ridge National Laboratory and described in detail by Larson.15 Briefly, the reflectivity measuring system consists of a reflecting microscope; a double-beam, null-balancing photometer array; a mechanically driven microscope stage; and a direct X-Y readout of the reflectivity of the specimen relative to its orientation on the microscope stage. The measuring photometer receives its signal from the specimen through a slotted Wright occular placed on top of the photovisual head of the microscope. The reference photometer receives light through a flexible glass "light pipe" from a mirror in the reflecting system of the microscope. Monochromatic light is attained through use of interference filters (15-nm half-peak width pass bands) placed in front of a stabilized Vickers 12 v, 100 w, tungsten-filament, quartz-iodide lamp.

Jan 1, 1970

By J. W. R. Rayner

THE conventional method of making water gas involves individual plants for the separate carbonization of coal to coke and the subsequent gasification of coke with steam. The process demands lump coke, preferably made from the best quality of coking coals. The ash in the coke should have a high melting point and the gasification process suffers a loss of efficiency when cokes with low ash-melting points are used. In Britain, these coals are generally the most expensive and they are readily available only in certain localities. The coals not suitable for making lump coke, or yielding only poor quality coke, are much more widely available and are generally cheaper. DEVELOPMENT OF ALTERNATIVE PROCESSES In Germany, processes have been developed and operated commercially for the production of water gas from very low-rank coals such as brown coal and lignites, but much less effort has been spent on processes to use coals of intermediate rank, which are widely available in Britain. The brown-coal processes use coal in the form of either dust or briquettes. The most successful of the dust-gasification methods is the Winkler process, which made a substantial contribution to German oil production during the war. It uses coal in the size range 0 to 8 mm and the fuel bed is blown with a mixture of oxygen and steam at a rate high enough to give it a characteristic boiling motion or, in present-day phraseology, at a rate more than sufficient to fluidize it (Fig. 1). Air cannot be used to provide the heat required for gasification, for vari¬ous reasons. In the first place, to make the process continuous by mixing air and steam would involve the production of a lean gas containing much nitrogen. If a separate blow were used, a large amount of potential heat would be lost because the blow gas in such a process would contain a very high percentage of carbon monoxide. Oxygen is necessary therefore and oxygen remains relatively expensive for use in gasification. In the Winkler generator, formation of clinker caused by local overheating does not occur, because of the mobility and high heat transfer of a fluidized bed. These properties of fluidized dusts have been used most successfully.

Jan 1, 1953

By Charles Dorrance

Culm is a general term used in the anthracite regions for many years to denote a mixture of coal, bony coal and impurities which is sent to the refuse-banks. Thus, 35 years ago culm contained the pea and buckwheat sizes of anthracite; but to-day, and as mentioned in this paper, culm is used specifically to denote the material which passes through the smallest screen in the anthracite-breaker. The smallest size of commercial anthracite is known as No. 3 buckwheat, barley, or bird's-eye coal, and is ordinarily made through a round-punched plate having openings & in. in diameter, and over a round-punched plate with openings 3/32 in. or 1/16 in. in diameter. Thus culm will consist of coal, bony coal, slate, gravel, iron pyrite, etc., ranging in size from 3/32 in. down to dust. Other local terms for culm are " slush," " silt," and " dirt." The first experiments towards the utilization of anthracite culm by briquetting, and the first briquetting-work done in this country, were in 1872 at Port Richmond Piers, Philadelphia, Pa., by E. F. Loiseau.1 Clay was used as a binder and the finished briquette was water-proofed with shellac, etc. Excessive cost was given as the reason for discontinuing work at this plant.

Jan 1, 1912

By Benjamin C. Craft

A review of development in North Louisiana during 1936 centers around the Rodessa field, in Caddo Parish. Continued extension of the

Jan 1, 1937