Search Documents

By Emmanuel N. Zevgolis

Energy required for roasting and smelting of a nickeliferous laterite ore by the rotary kiln - electric furnace process is investigated. From this work it comes that thermal energy is about 65% of the total energy needed and the rest is electrical. Also, 61.3% of thermal energy input in the roasting step (of all combustibles fed into the rotary kilns) is used for pre - heating, 11.6% for pre - reduction and the rest (27.1%) corresponds to the energy of the remaining carbon in the rotary kiln products (i.e., calcine, dust and coatings). Carbon entering the system is used as follows: 57.9% for combustion, 37.1% for reduction and the rest (5.0%) remains unburnt. Exploitation of energy from gases of both furnaces, as well as the higher possible reduction degree, the optimum temperature of the calcine and also elimination of the excess air in the rotary kilns, improve significantly energy balance and economics of the process.

Jan 1, 2006

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By R. E. Whitehead

"Abstract - Alkali-alumina and MgO-alumina plots are an effective instrument for displaying chemical and mineralogical compositions of altered and unaltered rhyolites and rhyodacites. They reveal that most supposedly unaltered rhyolites, apart from those of Cenozoic age, have undergone losses in Na2O and gains in K2O. The extreme loss of Na2O from highly altered rhyolites immediately adjacent to VMS deposits is strikingly illustrated by alkali-alumina plots. MgO/Al2O3 vs. K2O/Al2O3 diagrams display a strong negative correlation between MgO and K2O that results from the conversion of sericite to chlorite. A similar negative correlation between MgO and whole-rock d18O is apparent on plots of these two parameters. Alkali-alumina plots underscore problems in selecting appropriate precursor compositions required for mass-balance calculations. Molar ratio plots are a viable alternative to such calculations. Sommaire -Les diagrammes alcali-alumine et MgO-alumine constituent un instrument efficace pour la représentation des compositions chimiques et minéralogiques des rhyolites et rhyodacites altérées et fraîches.Ces diagrammes révèlent qu’à l'exception de celles d’âge Cénozoïque, la plupart des rhyolites qualifiées de fraîches ont subi une perte de Na2O et un gain de K2O. L’intense perte en Na2O que l’on note dans les rhyolites fortement altérées associées aux gîtes de type SMV est particulièrement bien mise en évidence par le diagramme alcali-alumine. Le diagramme MgO/Al2O3 vs. K2O/Al2O3 montre une forte corrélation inverse entre le MgO et le K2O due à la conversion de la séricite en chlorite. Une corrélation inverse analogue entre le MgO et le d18O de la roche totale s’observe sur un graphe comparant ces deux paramètres. L’usage du diagramme alcali-alumine fait ressortir combien il peut être difficile de choisir un précurseur de composition appropriée pour des calculs de balance de masse. Les diagrammes de rapport molaire constituent une alternative à de tels calculs."

Jan 1, 2006

As a result of cheap Maui gas and plentiful hydro-electricity, over the past few decades New Zealand has enjoyed some of the cheapest energy of any OECD country. The situation is changing; at best we are facing some radical changes in energy use, at worst we are facing a crisis resulting from the following:   Cause 1: Maui gas will be exhausted by 2012. Distorted pricing and supply contracts; resulted in Huntly Power Station, a coal mine mouth generator running on 70 per cent Maui gas until very recently!   Cause 2: Investment in new generating capacity (and transmission) is woefully inadequate; as a result hydro lake levels are being continually pushed to the limits.   Cause 3: Distorted thinking is everywhere, for example; æWe will find more cheap gasÆ. æGas is clean û coal is dirtyÆ. Hot air  û ægreen alternatives such as wind generation will save usÆ. æNo NuclearÆ. The outcomes of the distorted thinking will be price increases, then shortages (there is nothing like "black-outs" to focus national thinking) and finally recession.   But what can NZ do? - Mine Coal. Coal jump-started the industrial revolution, it can provide the transition to post-gas and oil. NZ has the second highest reserves of coal per capita in the world, yet we use less that any other country with significant coal reserves. Our exports of our best coal have increased threefold, yet out own consumption has remained static at about 1-1.5 Mtpa for the last 30 years. Our coal is NZ owned and inexpensive relative to other energy sources, even allowing for infrastructure and environmental costs.   What can we do? We as mining professionals can promote informed responsible development and investment in the country's mining and energy business. We can galvanise public opinion on issues such as æunbundlingÆ our entire energy chain from mine-to generator-through transmission, even if the nuclear issue has to wait! With oil above US$70/bbl substitution is feasible. For individuals, there is always solar!

Jan 1, 2006

By David Hake, David Salisbury

The Drainage Services Department (DSD) of the Hong Kong SAR Government commissioned the design and construction of the West Kowloon Drainage Improvement, Stage 2, Phase 2, Kai Tak Transfer Scheme (KTTS) project in 2000 to relieve potential flooding in Mong Kok caused by the insufficient capacity of the existing storm water drainage system. The KTTS involves construction of a 1.5km,4.4m drainage tunnel and a 450m long box culvert, running from Waterloo Road near Hereford Road to the existing Kai Tak Nullah in San Po Kong. This paper describes the design and construction of; the bored tunnel through both hard rock and soft ground using a slurry Tunnel Boring Machine (TBM), six associated access shafts, a connection structure at Waterloo Road and the box culvert connecting the bored tunnel to the outfall at Kai Tak nullah. Details will be provided on the contractor’s alternative designs adopted during the contract including the use of fibre reinforced shotcrete as one-pass temporary and permanent support for three of the shafts and modifications to the Engineer’s design for the box culvert structure.

Jan 1, 2005

By A Winchester, D Grant

The massive 1100 Orebody in Mount IsaÆs X41 Copper Mine has been extracted over the last 40 years form north to south utilising sublevel open stoping methods.De velopment has continually stepped ahead of production to provide access to new primary stoping blocks. The remaining secondary pillars contain stopes with one, two or three fill mass exposures and were constrained by access requirements and stope extraction turnaround time.The remaining southern mining areas consist of large 40 m wide by 300 to 400 m long east-west transverse pillars that have been left to provide access for ventilation and service requirements. Three large transverse cross-cuts or transverse pillars û 4180 x/c, 4010 x/c and the Panel pillar now remain. The 4180 x/c was the last major transverse pillar to be successfully broken.This transverse pillar is being extracted in a retreating sequence, creating 3SLOS stopes due to the surrounding backfilled stopes.In recent years the extraction of the first, and most critical, stopes in the transverse pillars have resulted in large changes to the induced stress field. This paper describes the extraction of the 1.1 million tonne stope P418 in the 4180 x/c pillar.T echnical challenges that were faced and how they were overcome to allow for the successful extraction of the stope are described.Critical to the success of the P418 stope extraction were the rehabilitation methodology used; extraction strategy modifications to address deteriorating ground; mass firings with multiple directional changes; managing the exposure of backfill of variable strengths; and geotechnical monitoring prior to, during and after extraction.

Jan 1, 2005

By Tim Edwards, Richard Triglavcanin, Ian Arbuthnot, Darren Colwell, Brad Garraway, Ken Roberts

"In the mineral processing industries, there is an increasing need to design thickeners which are able to produce high density underflows usually referred to as “paste”.The behaviour of a flocculated suspension in compression needs to be well understood in order to arrive at a reliable thickener tank configuration (i.e. diameter, cone angle and depth) for a required paste result.As a suspension approaches paste consistency, it’s fluid characteristics change markedly. It develops a high yield stress, and may have an increased tendency to form agglomerates, which lead to a phenomenon known as “rotating beds”, “donuts”, or “islands”. These characteristics present challenges to the designer of the rake mechanism.The subject paper addresses the requirements for designing a paste thickener, covering the following topics:o Testwork for thickener sizingo Design of rake mechanismso Suspension rheology and effect on designo Case studiesTESTWORK AND SIZING FOR PASTE THICKENERSThickening slurries to the maximum possible density (paste) is becoming increasingly common. Applications such as Autoclave feed thickeners, paste backfill and some counter current washing (CCD) circuits are all examples of potential paste thickening applications. The principle of paste thickeners is that the compression zone is much deeper than on either high rate (HRT) or high compression (HCT) units; generally 3 metres or more. As the compression zone gets deeper, theunderflow density for a given flux rate (tph/m2) increases, as a result of two factors:1. Longer bed settling time. Settling flocs move relative to one another and release interstitial fluid when they are in compression. Increasing bed residence time achieves higher density underflow as more fluid is removed.2. The nett weight of the bed creates a compressive force on the settling flocs. This force increases with depth, so that the flocs at the bottom of the bed experience the highest compressive force. This represents the driving force to expel interstitial fluid and hence increase bed density."

Jan 1, 2005

By Takuya Taguchi, Toshihiro Ogata, Atsuio Inoue, Shigeyuki Sasaki

Highly improved drilling machines and mucking machines have been used for the underground construction. To have rapid construction, the roles of blasting operation ha ve been growing more important. At the most tunneling of present, cartridged emulsion explosives have been used for a blasting in Japan. Under this circumstance, a blasting system of ANFO explosives using loading machine has been used recently for a tunnel blasting. However, ANFO has some problems, such as a useless explosives in wet boreholes, bad blasting fumes and the ammonia gas due to the decomposition of ammonium nitrate in contact with the sprayed concrete in tunnel.

Jan 1, 2005

By F. Siciliano, D. Bai, S. Yue, A. M. Elwazri

The influence of niobium addition and very low temperature (`cool') deformation on the microstructure and properties of low carbon microalloyed steels was investigated. In this work, the specimens were heated at 1200°C and held at this temperature for 20 minutes. Some specimens were aged at 400°C for times ranging from 10 minutes to 10 hours followed by air-cooling. Others were subjected to deformation at 400°C (`cool deformation') prior to aging. It was observed that the proportion of acicular ferrite was increased as the amount of Nb was increased. It was found that cool deformation increased both yield and tensile strengths significantly compared to that of the aged only specimens.

Jan 1, 2005

By Mutombo Nombe, Avimanyu Das, Rick Honaker

Enhanced gravity separators (EGS) provide a more efficient separation than froth flotation when cleaning coal in the 150 x 25 µm particle size range. To improve the performance of an EGS unit, air bubbles were injected into the feed stream in an attempt to decrease the apparent density of the coal particles due to the formation of bubble-coal particle agglomerates. Air injection had a significant impact on operating characteristics and separation performance. Coal recovery was increased by 10 to 20 absolute percentage points while a 2 percentage point drop in the minimum product ash content was also achieved.

Jan 1, 2005

By D K, S Freij, A Rossiter, X Han, B Feng

In mining operations, the removal of overburden to expose the ores is achieved by rock blasting using ammonium nitrate based explosives, eg ammonium nitrate-fuel oil mixtures, commonly known as ANFO. However, ammonium nitrate can react with pyritic shales that are often found in many mines, leading to premature detonation or spontaneous explosion. In order to minimise the occurrence of spontaneous explosion, the reactivity of the shale in a mine must be assessed. This will provide a better understanding of blasting risks and thus will improve the safety and the cost efficiency of blasting through the selection of appropriate explosives. In this study, shale samples were collected from different locations in Western AustraliaÆs Mt Whaleback iron ore mine and geochemically characterised. The reactivity of the shale samples towards ammonium nitrate and ANFO was investigated using a combination of large-scale firing range tests and laboratory isothermal reactor tests. Results of the firing range tests show that the reactive ingredients of the shale are the limiting factor for the reactions between shale and ANFO. Based on the firing range test results, further isothermal reactor tests were conducted to investigate the reactivity of shale samples towards ammonium nitrate under controlled conditions. Analysis of the results from the firing range tests and the isothermal reactor tests shows that there are correlations between the reactivity of shale samples and several geochemical characteristics such as sulfate, sulfur, ferrous and zinc content.

Jan 1, 2005

By J. Lu, J. B. Wiskel, D. G. Ivey, E. Niemi, H. Henein

Simulated TMCP using a Gleeble was undertaken to evaluate the effect of the austenite to ferrite cooling rate, coiling temperatures of either 400°C or 500°C and the magnitude of plastic deformation at the coiling temperature on the hardness of a Grade 483 (X70) steel. For comparable apparent cooling rates and deformation conditions, the hardness of the samples were independent of coiling temperature The application of a minimum compressive deformation > 8% was required to increase hardness at both simulated coiling temperatures of 400°C and 500°C. An increase in hardness was also observed with increased cooling times between 800°C and 500°C (i.e., slower cooling rates).

Jan 1, 2005

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

By P. S. Paul

Mine accidents/injuries are complex and generally characterized by several factors, from technical to social characteristics. In this paper, a sociotechnical model for work injury in mines was developed and tested through structural equation modelling with application to case study mines in India. In total 14 variables were considered in this study. Most of the variables are not directly quantifiable. Instruments were developed to quantify them through a questionnaire survey. Underground mineworkers were randomly selected for the survey. Responses of 300 participants were used for the analysis. The analysis was conducted in three parts. Firstly, high-low plots were constructed to explore the variations in responses to the questionnaires by the accident involved (AG) and non-involved (NAG) workers. Secondly, a t-test was conducted to see whether the responses were significantly different for the two groups or not. The chi-square results showed significant differences of responses among the two groups. Finally, how these difference scan cause accidents/injuries in mines was hypothesized and evaluated using structural equation modelling. The measurement model of the Linear Structural Relations (LISREL) program was used to identify the latent constructs of the sociotechnical model. The structural model of LISREL was used to estimate the interrelationships among the constructs. The case study results showed that there is a sequential interaction among the sociotechnical factors leading to accidents/injuries in mines. Work hazards induce more job stress in the workers while social support mitigates the same. Job stress and safety environment predict the workers? job involvement. A worker who is more job-involved exhibits better safety performance, which in turn reduces work injury. The safety environment is shown to have a direct mitigating effect on work-related injury. The findings of this study clearly revealed that job stress and safety environment are the two key factors influencing work-related injuries in mines that need to be addressed properly through effective safety programmes.

Jan 1, 2005

The homologous series of saturated fatty acids investigated in this study generally show a steady gradation of properties with chain length. The solution pKa values were assumed constant at 4.9, however reported pKa values could be lower or higher. Hematite flotation response and surface pressure for aqueous solutions of these fatty acids were measured as a function of pH. For the shorter chain fatty acids, the undissociated acid was shown to be the predominant surface active species with flotation, supplemented by the physical adsorption of acid anions as the chain length increased. The reduced solubility of the longer fatty acid carbon chains made these reagents ineffective as flotation agents. The maximum flotation response of hematite using tetradecanoic acid corresponded with the precipitation edge of the reagent. The results show that the values of surface pressure of the surfactants are not always a good indication of their effectiveness as flotation collectors.

Jan 1, 2005

By V Kumar, A S. Venkatesh, R K. Upadhya

The enormous iron ore deposits of eastern India are part of the volcano-sedimentary basins containing iron and to some extent manganese deposits that belong to the Iron Ore Group (IOG) of Archaean Singhbhum Craton, occurring as western and eastern limbs of a broad synclinorium. The eastern iron basin contains typically huge amounts of blue dust and powdery ores. There is a remarkable difference between the western flank ores and the eastern flank ores and the present study is part of the eastern flank ores from Noamundi. Demand for sintered fines as blast furnace feed coupled with the higher export price for lumpy ores that produce enormous amounts of fines during processing has created a situation whereby both primary and secondary fines, such as classifier fines, are being increasingly used as sintered feed for blast furnace. Systematic mineralogical and geochemical characterisation indicates that in many cases the ROM and classifier fines have to be processed to increase their Fe content and at the same time reduce their Al, Si and P contents. The fines which are already at micron sizes are amenable for beneficiation using the Mozley mineral separator and sink float test. It was observed that beneficiation was better and significantly greater by the sink float method than the Mozley mineral separator. Mineralogical and chemical studies of the fines reveal that around 80 per cent of alumina bearing minerals (gibbsite, clay and silicates) are present in the liberated form. Microscopic studies confirmed that the iron minerals are well liberated by controlled grinding to -300 mesh sizes with the beneficiation of iron ore fines and low-grade ores carried out using the Mozley mineral separator and sink float test. Beneficiation using the Mozley mineral separator increased the grade of concentrate with increasing flow rate of water as well as increase in amplitude of oscillation of the tray, but not very significantly with the increase in slope of the tray. In this method, though, iron concentration improved from 47 to 63 per cent with a recovery of around 67 per cent. It is not suitable for industry scale operation as only a small quantity of ores can be handled at a time. Beneficiation using the sink float test produced a better result with the Fe content increasing from 47 - 49 per cent to 66 - 68 per cent with a recovery of approximately 58 per cent. Initial feed Al2O3, SiO2 and Fe contents of 9.85 per cent, 15.3 per cent and 49.8 per cent respectively were beneficiated to 2.13 per cent Al2O3, 1.5 per cent SiO2 and 67.5 per cent Fe in the concentrate, with a recovery of 54.1 per cent. In contrast, using the Mozley table resulted in beneficiable contents 66.3 per cent Fe, 3.01 per cent alumina and 2.05 per cent silica. The combined alumina and silica content for the Mozley Table was >5 per cent, which exceeds the industry requirement of

Jan 1, 2005

By C. M. Diaz, S. W. Marcuson

In the late 19th century, the discovery of rich nickel-copper sulfide ore bodies in Sudbury and the need for tonnage quantities of the metal to be used in nickel steel armor provided the foundation for establishing the Canadian nickel industry. For almost 50 years, International Nickel was the key player. In 1930, Falconbridge Nickel entered the field. These two companies remain the key Canadian nickel producers. This paper discusses the factors that have influenced the evolution of nickel smelting processes. The initial Sudbury ore smelting and nickel copper separation technologies were imported from abroad. It was only in 1937 that International Nickel established a process research laboratory in Copper Cliff The explosive post WW II industrial development created a strong demand for a broader variety of nickel products. For both International Nickel and Falconbridge, R&D became an essential business tool to succeed in the new market scenery. In the last few decades, new technologies were developed and commercialized to respond to the raising cost of energy, society pressing environmental concerns, the advent of nickel laterites as an important source of new metal, the incorporation of new nickel producers to the market, and, therefore, the need to increase productivity. Canada thus became an important exporter of technology. In this paper, the authors review this history with the objective of highlighting the forces that have triggered the most important changes in Canadian nickel smelting.

Jan 1, 2005

By T. P. R. de Jong, H. Harbeck

"This contribution reports recent mineral sorting experience and lists the opportunities of the newest generation of automatic sorters with a special focus on electromagnetic detection and Xray transmission. With the available sensor resolutions and actuator systems that are available today sorting of minerals down to 2 mm size and up to 250 mm lump size is technically feasible. In industry, ore as well as coal is still hand-picked and current automation potential only utilised in a handful of specific applications. Recently a number of technological developments took place that may increase sorting potential, save mill costs and lead to lower overall tonnage costs.They are:??High speed and high resolution sorting systems based on X-ray transmission imaging??High speed on-line image processing and further development of advanced data processing??Modular multi-sensor automatic sorting units (using one or more sensors such as colour, electromagnetic and X-ray in a single device)??Sensitive electromagnetic sensors for sorting based on differences in magnetic susceptibility and electric conductivityThe above enables compact dry separation, insensitive for moisture fluctuations and at high separation sharpness, as well as “electronic” high gradient magnetic separation for larger particles. Besides conventional X-ray transmission (XRT), dual-energy XRT (DE-XRT) is now being redesigned to meet the requirements of the mining industry. The mentioned technologies provide automatic dry separation of minerals and rock as alternative for conventional processing."

Jan 1, 2005

By Fumito Tanaka

The Mitsubishi Process is the sole pyrometallurgical process for the continuous production of blister copper from copper concentrates. Continuous converting originates from the application of the proven technology of a lime-ferrite slag (CaO-FeOX-Cu2O) on the Converting Furnace (C-furnace). Recent improvements on the C-furnace operation have included increasing the processing of recycled materials and the investigation of alternative fluxing agents. However, some minor oxides adversely affect C-furnace operation, with respect to magnetite behavior of the slag, with the most significant impact having been observed with the silica content of the slag. This paper will quantify the impact of silica on the lime-based slag, and discusses the controls that have been identified to sustain continuous converting operation.

Jan 1, 2005

By Patrick Pelletier, Pierre-Alexandre Bossé, Julie Fournier, Gianni Bartolacci, Jayson Tessier, Ahmed Bouajila, Carl Duchesne

"This paper summarizes research into the study of the control of flotation processes based on froth images. The use of numerical image analysis techniques for the extraction of significant patterns (froth structure and colour) from industrial flotation froths is discussed.First, the froth was analysed by the use of the Multivariate Image Analysis (MIA) method to extract the spectral variation contained in a RBG image. The Partial Least Squares (PLS) was applied to develop the empirical model for the prediction of froth grade. The results of this application are illustrated using one industrial case study.Second, the froth was also analysed by Gray Level Co-occurrence Matrix (GLCM) and Wavelet Transform Analysis (WTA) to extract features related more to morphological aspects. Since there is useful information hidden in froth texture, these methods are used as texture descriptor to classify different types of froths.Third, a control strategy based on a froth structure indicator was developed and implemented on an industrial zinc flotation circuit. The feedback controller uses a reagent flow-rate in order to maintain the froth structure at its set point. Process improvements obtained with the implemented control strategy are highlighted.Finally, the feasibility to implement a hybrid control strategy consisting in a froth structure supervision controller based on the froth concentrate grade estimated by MIA and recovery inferred by image analysis is discussed.INTRODUCTIONThe development of control strategies to achieve satisfactory control performance has always been a great challenge for engineers and the need for improved process diagnosis, control and optimization has become more and more evident for the mineral processing industry in the last decades. That is why new process variables need to be measured particularly in highly multivariable processes such as flotation. This industrial process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and/or chemical ore characteristics and also, due to some irregularities in manual process operating procedures. A flotation circuit scheme is always a complex network of more than two dozens slurry streams. Information about those streams (% solid, metal content analysis and flow rates) is important for process diagnosis performance evaluation and control. Also, because of the grade decrease and increasing complexity of the new processed ores, more instrumentation outputs and more powerful and significant pr"

Jan 1, 2005