Search Documents

By F. P. Bobrowski, G. B. Spencer, Alton B. Cook

In estimating production gas/oil ratios and oil recoveries from reservoirs containing highly volatile oils it is highly important to include condensate that may be recovered from the gas produced from the reservoir. The volume of the hydrocarbon liquid condensed from the production of the solution gas that has been liberated. in some reservoirs may equal or even exceed the volume of recoverable stock-tank oil as estimated by present methods. The usual procedure1, 2, 3 in estimating future reservoir performance includes use of relative permeability data of the reservoir rock to gas and oil and includes material-balance calculations utilizing data on the volume of the reservoir fluids, oil and gas production and reservoir pressure decline, and data on the physical properties of the initial reservoir fluids. The inaccuracy in the procedure results from the false assumption that all of the free or liberated gas that enters the well bore of reservoirs containing highly volatile oils remains in the gaseous phase as it is produced. This paper presents a method for estimating future reservoir performance and oil recoveries based on special labora. tory analyses of reservoir-oil samples and recognition of the additional volume of hydrocarbon liquid that will be recovered at various stages of depletion from a solution.gas.drive reservoir. The method also includes calculations of the volume and composition of the hydrocarbon liquids that can be recovered by processing the produced gas in a natural-gasoline plant. The development of the method resulted from a study of laboratory analyses of reservoir samples and of field data obtained from two reservoirs containing oil of the highly velatile type. Relatively high pressures and temperatures prevail in oil reservoirs discovered at the greater depths of present-day drilling. The contained fluids may have high saturation -Dressures and large volumes of gas in solution. The oils and gases under these conditions may be almost identical in compositions and densities.4,5 Also, engineers have noted that, for a number of oil reservoirs and especially the deeper reservoirs, the API gravity of the stock-tank oil increaees as the production gas/oil ratios increase. They attributed this increase in API gravity of the stock-tank oil to the formation of condensate as the liberated gas in the reservoir is being produced. SOURCE OF DATA FOR CALCULATIONS Subsurface oil samples and well-test data were obtained from the E. Constantin-Lambert Well No. 1 in the Elk City Field, Okla., to demonstrate the need for and a method of calculating future reservoir performance when consideration is given to the recoverable hydrocarbon liquid from the production of solution gas that has been or will be liberated in a reservoir. The Lambert well is located in C, SW 1/4, SW 1/4, Set- 18, T-l0-N, R-20-W, Washita County, Okla. At the time of completion it was on the east edge of the development and Was producing from conglomerate through 30 perforations in the 5 1/2-in. casing at a depth of 9,859 to 9,864 ft. The well Was completed on July 9, 1949, and subsurface oil samples were obtained July 29 and August 1, 1949. Production gas/oil ratio data were obtained during the operation in series of two Separators at high and low-pressures of 314 and 44 psia, respectively, and at an average temperature of approximately 60°F. The flowing bottom-hole pressure at the time of sampling was 3,934 psis. The static bottom-hole pressure was not obtained at the time of sampling, as the well could not be shut in long enough for testing because gas produced from the well was used for fuel at an offset drilling well. However, the initial reservoir pressure was calculated to be 4,364 psia from knowledge of pressure gradients in other wells in the field and the depth of the casing perforations in the Lambert NO. 1 well.

Jan 1, 1951

By J. G. Kirby

The total number of petroleum refineries in the United States continued to decline during 1950, and according to the Bureau of Mines annual refinery capacity survey there were 357 refineries January 1, 1951, compared with 367 a year ago. The total throughput capacity increased 267,344 barrels daily during the year to 6,963,644 barrels daily as of January 1, 1951, continuing the trend of the past several years to increase the throughput capacity of the refineries and decrease the number of plants. The capacity of the average refinery to process crude oil increased during 1950 from 18,246 barrels daily to 19,506. The Indiana-Illinois refinery district accounted for 110,175 barrels, or 41 percent of the total crude-oil capacity increase, the Oklahoma-Kansas district, 17 percent, the California district, 14 percent, the East Coast district, 13 percent, and the Louisiana Gulf Coast district, 12 percent. Slight declines ill crude-oil capacity were reported in the Texas Inland, Texas Gulf Coast, New Mexico, And Appalachian refinery districts. The 160,100 barrels of additional crude-oil capacity that was building January 1, 1951, represents an increase of 10 percent over the year earlier figure. The only completely new refinery listed as under construct ion at the beginning of 1951 is located at Superior, Wisconsin. Other new construction involves enlargement of existing refineries. Plans for at least five additional new refineries are under consideration, and construction is expected to begin during the current year.

Jan 1, 1951

By William H. Lyon

In 1950 the Program Staff of the Department of the Interior undertook an exploratory study in the projection of energy requirements of the nation. This work was reported in Bureau of Mines Information Circular 7582 by H. J. Barnett. In that preliminary study Mr. Barnett, after exploring the nature of the energy economy in some detail, evolved a method for estimating how much energy will be required in the future, based on estimates of trends in efficiency of energy utilization in specific applications, the physical output of specific energy-consuming industries, size of the population, productivity advances in the economy at large, consumer preferences, and other factors. Considerable new information was developed regarding the nature of energy demands and the possible levels of requirements for each fuel under various assumed business conditions. The study analyzed the interrelationships, including substitutions, among the fuels and emphasized the need for viewing the energy economy as an integrated albeit complex whole. This exploratory study showed a need for a single comprehensive statistical re-port that would assemble and show in a uniform manner the diverse published statistical data on energy commodities now scattered through many publications. A particularly important need was for a set of historical statistics showing the production and consumption of all energy on a B.t.u. basis. As the prospective size and nature of the future energy requirements of the nation are matters of continuing importance, this report was prepared to assist further investigations of the subject. In this report the authors undertake to assemble and present in tabular form, on a uniform basis, the production and use of each of the fuels and electric energy in the United states for three census years -1929, 1939, and 1947. The year 1947, rather than a later year, was selected because it is the most recent year for which census data are available showing the consumption of fuel by each of the manufacturing industries. It is hoped that making data for these 3 years available in one re-port will provide the needed statistical background for further studies of fuel requirements and supplies.

Jan 1, 1951

By Cecil Q. Cupps

Results are presented of a comprehensive study of the characteristics of the original oil in the Weber sandstone reservoir, Rangely oil field, Colorado. Through the medium of subsurface sampling, adequately representative samples of the original reservoir oil were obtained from many parts of the reservoir over a period of 5 years concurrent with active development of the reservoir. Data of differential gas liberation, pressure-viscosity, and. pressure-volume-temperature relationships are shown for 12 subsurface oil samples. Data also are given of reservoir pressure and. temperature, composition of liberated or solution Gas, composition of 22 produced-gas samples, and Hempel analyses of crude-oil samples from 18 wells. The characteristics or physical properties of the 12 subsurface oil samples, as determined by laboratory analyses, were correlated with elevation of the top of the Weber sandstone. These relationships of oil characteristics to elevation in the reservoir show that only the oil in contact with the initial gas cap was gas-saturated at the existing pressure and temperature. The characteristics of the original reservoir oil were marked by an appreciable decrease of saturation pressure and solution gas-oil ratio and increase of viscosity and density with depth below the gas-oil contact. The composition of solution gas and of' produced was also was found to vary with elevation of the oil in the reservoir.

Jan 1, 1951

By Glenn C. Reed

This report is one of a series based upon investigations made and being made within the Missouri River Basin in Montana by engineers of the Bureau of Mines , Albany Branch , Mining Division . These investigations are made primarily to provide preliminary information to the Department of Interior agencies and to others concerned with planning the proposed Federal power development within the Missouri River Basin . The present report has been designed to permit public distribution of factual data obtained . The field investigations were made during the late fall of 1947 and the summer of 1948. Information on mineral occurrences in several areas in Sweet Grass County also are included in this report because of their close proximity to Park County . Practically all known metallic mineral deposits within Park County were investigated ; some nonmetallic mineral deposits also were investigated. The investigations of the metallic mineral deposits in Park County cannot be considered complete ; some long inactive mines and prospects on which little or no information is of record may have been missed . Many of the underground openings , especially at the long inactive properties , no longer are accessible ; consequently , much of the information regarding history their and development necessarily has been obtained from available Federal and State publications .

Feb 1, 1950

By R. A. Cattell

Progress of Bureau of Mines research related to oil and gas during the past fiscal year has been marked by the publication of more than 40 reports on the various phases of the work . These include papers dealing with the production of oil and gas , transportation of gas , chemistry and refining of petroleum , thermodynamic properties of hydrocarbons , and the processing and utiliza- tion of helium . As an additional service to Pennsylvania oil operators , a new suboffice was opened in Bradford , Pa . , during the year . With this addition , the work of the Petroleum and Natural Gas Branch of the Bureau of Mines is now conducted in two large stations , the Petroleum Experiment Station , Bartlesville , Okla . , and the Petroleum and Oil Shale Experiment Station , Laramie , Wyo . , and three field offices and laboratories at San Francisco , Calif . , Dallas , Tex . , and Franklin, Pa., and two suboffices, Wichita Falls, Tex., and the newly opened suboffice at Bradford, Pa. In addition, this Branch operates large-scale helium-production plants in Texas, Kansas, and New Mexico, and maintains ex- tensive helium-bearing gas reserves in Texas and New Mexico. All helium opera- tions are supervised from headquarters at Amarillo, Tex. A small headquarters staff is in Washington, D. C. A backward glance at the road traveled during the past several years by the Petroleum and Natural Gas Eranch of the Bureau of Mines brings out a general background for the events of the fiscal year 1949. Throughout the fiscal year 1945, the activities of the Branch were still mainly concerned with such war activities as making special field studies for the Petroleum Adminis- tration for War, finding ways of increasing rates of production, and supplying data pertaining to the manufacture of aviation and jet-propulsion fuels. A period of adjustment came in 1946, characterized by a turning from war to peace procedures and efforts to give wide distribution to technical facts ob tained in wartime research; also, there came a realization that the demands of war had broadened the horizons of research. This was emphasized in 1947, when a peacetime program was restored, based upon the long view of the Bureau's place as a research agency in oil and gas. Close attention was given to tech- nical detail in 1948, and emphasis was placed on maintaining a balance between the industrial need for technical knowledge and Governmental-research possi- bilities in the fields of (1) withdrawal of petroleum from natural deposits, (2) utilization of petroleum and its products, and (3) commercial utilization of helium. Studies of petroleum production and utilization and helium production and utilization are the normal functions of the Branch. These functions (sometimes expressed in different words) have been the mainstay of this organization since initiation of the work. The details of approach vary with changing conditions, but, fundamentally, the functions have been the same in both peace and war. The work of the past fiscal year has emphasized the advantages that accrue when Government and industry join in a wise use of technical and scientific knowledge gained through research. Outstanding evidence of the beneficial results of cooperative effort by the Bureau of Mines and various organizations is found in the following typical examples, the details of which are discussed in the body of this report. Working in close cooperation with operators along the Gulf Coast, the Natural Gasoline Association of America, and the National Association of Cor- rosion Engineers, the Bureau found, through field testing, that corrosion protection by means of chromates in high-pressure gas-condensate wells costs less than $1 per million cubic feet of gas produced. Laboratory experiments to measure the corrosion effects of carbonic and propionic acids on various steels and alloy steels gave data that will serve as guides in the selection of new. materials for the construction of well equipment to be tested by industry under actual service conditions.

Feb 1, 1950

By G. W. Jones

In the course of experiments on the stabilization of acetylene gas by addition of other gases, notably hydrocarbons such as methane, propane, and butane, it was observed that large quantities of carbon black are produced during the explosion of acetylene or mixtures of acetylene with the, above hydrocarbons, the added hydrocarbon being essentially decomposed into hydrogen and carbon. It is known that in the complete absence of air acetylene explodes upon application of an intense ignition source at pressure above 5.9 p.s.i. gage. The same is true of mixtures of hydrocarbons and acetylene. However, the pressures necessary for explosion are considerably higher in the case of these mixtures and depend on the amount of added hydrocarbon. The present report contains data on gaseous products and the physical characteristics of the carbon black formed by explosion at elevated pressures of various mixtures of acetylene and hydrocarbons as well as other gases, such as hydrogen, helium, nitrogen, and carbon dioxide.

Jan 1, 1950

By Harold L. Gibbs

The purpose of this paper is to encourage petrographers to prepare thin sections, as the demand for microscopic examination of rocks, ores, and metallurgical products is becoming more general in .the mining metallurgical-fields. This paper has been written with the knowledge that the successful thin-section methods and the several new techniques herein described will be helpful to all engaged in this field of work. Detailed instructions for making thin sections by methods developed at the Salt Lake-City laboratory of the Bureau of' Mines are given in this paper. Several new techniques are described for making thin sections of loose grains and fine sands and for making good thin sections of highly altered and friable rocks. The methods described insure superior bonding of the rock to the glass slide, thus virtually eliminating any failures due to parting of the section from the glass slide, and permit fast mounting, grinding, and finishing, thereby materially lessening the time required to prepare thin sections.

Jan 1, 1950

By Ming-Kao Yen

A considerable amount of work has been reported in the literature in regard to the texture and earing behavior of copper strip. The rolling texture of copper has been confirmed as (110) [112] and (112) [111], which yields ears of a drawn cup at the position 45" from the rolling direction.1-3 The recrystallization texture has been established as the cubic or (100) [001] texture, where the earing positions are at 0" and 90" to the rolling direction.4-8 It has also been reported that in the development of cubically aligned grains of copper strips, the percentage of this cubic texture increased with an increase of final reduction and final annealing temperature.8,9 A comprehensive study on H.C. copper (British commercial copper of high-conductivity quality = Cu 99.95 pct, O2 0.03 pct, Ag 0.003 pct, Fe 0.005 pct and Pb < 0.001 pct) was made by Cook and Richards.6 They concluded that the recrystallization textures could be described as one or more of the following textures: (1) a single texture (100) 10011, (2) a twin texture (110) [112] and (3) a random orientation, depending upon the previous history of the specimen concerned. The effect of various alloying additions in copper was reported by Dahl and Pawlek.10 They found that certain alloying additions, such as 5 pct Zn, 1 pct Sn, 4 pct Al, 0.5 pct Be, 0.5 pct Cd, or 0.05 pct P suppressed the formation of cubic texture. Brick, Martin and Angierll reported that the cold rolled textures due to various additions fitted a rather simple pattern. However, the recrystallization textures were subject to very considerable variations. In the discussion of this paper, Baldwin stated that deoxidized copper containing 0.02 pct P gave a complicated recrystallization texture at lower temperature. When this copper was annealed at high temperature, a single texture appeared which was described as (110) [ill] but. according to a pri- vate communication from Baldwin, this orientation reported was in error and should have been reported as (110)[112]. He also reported that the earing positions of drawn cups were at 60" to the rolling direction.12 Recently, Howald, in his discussion on the paper by Hibbard and Yen,13 reported that the rolling texture of phosphorus deoxidized copper, containing from 0.006 to 0.020 pct phosphorus, was of the pure copper type. When these coppers were annealed at lower temperatures, they exhibited a random orientation, and when they were annealed at higher temperatures they had a mixed (111)[110] and (100)[001] texture, depending on the severity of the final reduction and annealing temperature. However, the specific influence of phosphorus and other impurities on the recrystallization textures and the deep drawing properties of copper strip has not been thoroughly reported. Therefore, an attempt has been made in the present work to determine the rolling and recrystallization textures and also the earing behavior of five types of commercial copper and thereby to evaluate the effect of phosphorus and some other significant impurities on the development of texture for cold reductions of about 87 to 89 pct. Materials Used The five types of copper employed in the present investigation were two phosphorus deoxidized coppers of different phosphorus content (0.007 and 0.013 pct P), an oxygen-free copper (OFHC), an electrolytic tough-pitch copper, and a fire-refined tough-pitch copper. These materials were subjected to a thorough spectroscopic and chemical analysis. The designations and the chemical compositions were as shown in Table 1. The coppers, FA1, FA2 and FA3. were hot-forged from 3-in. billets into a ½ X 6-in. plate and cold rolled to the ready-to-finish gauge indicated below. FA4 and FA5 were hot rolled and scalped to ready-to-finish gauge. The grain size of all the materials in the ready-to-finish condition was about 0.030 to 0.045 mm. Table 2 shows the last stage of the production schedule for each copper strip used. Experimental Procedure ANNEALING, GRAIN SIZE AND HARDNESS DETERMINATIONS Specimens of each type of copper were finally annealed in air for periods of one hour at temperatures ranging from 300 to 1600°F and were subsequently cooled in air. The average grain diameter of the annealed specimen was estimated by comparing with a standard grain size chart. Hardness was determined on the Rockwell 15 T scale. CUPPING TESTS Cups were made in a blanking and drawing set, in which blanks of 2-in. diam were drawn to a cup of 1.25-in. diam with an average depth of about 0.75 in. The clearance between the punch and die was about 0.032 in. The ears of the cup were measured with a special fixture which read the height of ears to one-thousandth of an inch on every ten-degree interval along the circumference of the cup. POLE FIGURES The usual transmission diffraction method with unfiltered copper radiation was employed to determine the pole-figures of the specimens cold-rolled or annealed at 900°F. All the pole-figures were derived from the positions of intensity maxima on 111 diffraction rings of the X ray photo-grams taken at 10 rotation of a

Jan 1, 1950

By A. J. Kauffman Jr.

The Petrographic Section of the Bureau of Mines, Northwest Electrodevelopment Laboratory, Albany, Oreg., annually examines thousands of minerals and rocks. Samples are received from mining, engineers, prospectors, and government agencies, both State and Federal. During the past 2 years certain uncommon minerals have been identified in the samples submitted. Eleven occurrences have been selected for reporting in detail. These selections were made because in most cases a new locality is involved. The data reported are the result of application of the latest techniques, and widely disseminated references concerning each mineral have been added for completeness. Several occurrences have been described by other investigators; in those cases new data have been supplied to supplement the already published information on these occurrences. No uranium-bearing minerals have been included; they will be treated in another paper. The Bureau of Mines does not make chemical analyses or assays for individuals or firms In direct competition with private laboratories. Mineral¬ogical examinations, however, are made for prospectors and the general public. Such examinations a call surface to determine whether the sample in question has possible commercial value. If it has apparent value, the sender is so informed, and suggestions as to its .Arc, development and marketing are offered. The latest scientific apparatus is available to aid in identification. The apparatus includes microscopes, both wide-field and polarizing, a Bunsen-type spectroscope for visual observation of the Zinc and band spectra of many elements, differential thermal apparatus for the examination of hydrous material, apparatus for cutting and mounting either thin sections for study in transmitted or polished surfaces for reflected-light studies, and a high-intensity magnetic separator for concentrating minerals according to their magnetic susceptibility. Also, available, but not an integral part of the Section, are several laboratory-type Geiger counters, a grating spectrograph, and X-ray diffraction apparatus. If need be, all of these tools may be employed to identify a mineral or rock.

Jan 1, 1950

By F. R. Erick Mulder

"AbstractTwo bottom-hole samples have been taken from two new completions in the Turner Valley field, Royalite Lowery No. 8 on the west flank and Royalite No. 73, which was deepened into a lower fault block, on the northeast flank. From the bottom-hole oil of Royalite Lowary No. 8 a synthetic sample was prepared to simulate the original fluid in the reservoir, saturated at the gas-oil contact conditions. The sample from Royalite Lewery No. 8 has been shown to be the original fluid present at this well and represents the oil phase near the oil-water contact in• the reservoir. Complete chemical analysis, P.V.T., and viscosity data have been obtained on these reservoir fluids, which represent the range of saturation from the gas-oil to the oil-water contact in the Turner Valley oil structures. Sampling techniques and the application of the analytical data to reservoir conditions and field operations are discussed. Super-compressibility curves for an average separator tail gas have also been prepared. These data have not been available before. They will be of fundamental value in futu.re reservoir engineering studies of this field and will also serve as a guide in determining operating practices."

Jan 1, 1950

By H. C. Gunning

Introduction The invitation to contribute a discussion on some of the broader features of the mineral deposits of our Cordillera seemed acceptable enough when presented several months ago. More mature consideration has impressed upon me the difficulty of making any constructive or very helpful contribution in the short time available and with my limited inspiration. Dr. Lang deserves our real gratitude for his general paper of nineteen pages at the beginning of the Volume. Into it, with the help of two diagrams and seven tabular summaries, he has packed a lot of useful information and has analyzed along several lines the data of the Volume&apos;s twenty-eight detailed papers on our mines and camps. He has added additional facts from his own knowledge of the region. I am sure that, like myself and the whole fraternity, he feels especially grateful to the eleven company geologists who found time to contribute detailed descriptions of mines they have studied. The Regional Situation With the Jubilee Volume and two recent publications of great value from the Geological Survey, we are more up-to-date on Cordilleran geology than we have ever been. But I would like to emphasize that we still have but fragmentary information. Brief study of G.S.C. Map 932A will illustrate this. Our knowledge of the Rocky mountains is limited to two narrow sections along the main railway lines, a somewhat larger area from the border north along the Mesozoic coal-bearing basins, and some reconnaissance along Peace river and the Alaska highway. There is some additional information on old maps, particularly those by G. M. Dawson, but it is very much of the &apos;exploratory&apos; type. The other mapped areas are chiefly in the accessible region south of &apos;fifty-one&apos;, in the central part adjacent to and spreading north, recently, from the Canadian National railway, and along the edges of the Coast Range.

Jan 1, 1950

By Albert L. Toenges

Alaska requires an adequate fuel supply for its development, and has large potential coal reserves ranging from lignite to subbituminous and anthracite. Coal production in the Territory now is less than the requirements. In L947, production was 361,000 tons, divided about equally between bituminous coal from the Matanuska field and subbituminous coal from the Nenana field. There is need for development of modern mechanized mines, which should produce the required output with a minimum of workers. These mines should not be thought of in the light of large potential capacity, as in the States. However, these new mines should be developed by modern methods, which should result in lower costs than at Present. Because of the diverse physical conditions in the coal fields, intensive investigation by diamond drilling is necessary to properly plan the development and equipment of mine sites at minimum cost. The Bureau of Mines is doing this now in the Wishbone Hill area of the Matanuska field. All coal land in Alaska is government-owned and subject to the Coal Leasing Act. Coal mining in Alaska has been handicapped by an inadequate supply of dependable workers. Wage scales have been very high in recent years, and "floaters" have been attracted to the coal mines. This type of labor is not conducive to efficient operation. Modernization of mines will require skilled and dependable workers and to induce such men to become interested in coal mining in Alaska, modern facilities, such as modern houses, schools, churches, and recreation halls, must be provided near the mines. Alaska is still a frontier and improvements in living standards must accompany development of mines in order that a stable community may be established. Coal is known to have been mined in Alaska at Port Graham, on Cook Inlet, by the Russians in 1854. During the Klondike gold rush in 1898, coal was mined in scattered areas for use on steamers plying the Yukon River and its navigable tributaries. After the Alaska Railroad was built, two important fields were developed—the Nenana and the Matanuska (Fig 1). The Bering River field was explored by the Guggenheim interests at one time, and a railroad to the area was constructed. However, the field was abandoned because of litigation and reported unsatisfactory physical condition of the beds. There are areas that today are unimportant but which may be developed in the future. Possibly the most important of these is the deposits of subbituminous coal adjacent to Cook Inlet, near Homer, on the Kenai Peninsula (see Fig 1). It is expected that the demand for coal in the Kenai Peninsula will increase because the population in that area has increased as a result of agricultural development. Numerous outcrops of coal are exposed on the peninsula and development of a mine there would obviate dependence on supplies of coal from the Matanuska field. Coal from this field must be shipped approximately 160 miles by rail to Seward and transported thence by boat about 180 miles to Homer. There has been no regular boat service from Anchorage to Homer. There are deposits of coal in the Arctic region but a description of them will not be given in this paper, which will describe the more important deposits in the Alaska Railroad belt. The results of a reconnaissance in the Arctic have been described.&apos; Description of Fields MATANUSKA FIELD The Matanuska field lies in the valleys of the Matanuska River and its tributaries and their separating ridges. This field has been interpreted by geologists as a sunken fault block that separated the Talkeetna Range of mountains from the Chugach Range. The Matanuska River flows west along the south side of the field and the Glenn highway, which extends from Anchorage via Palmer to the Richardson highway near Glen Allan, follows the Matanuska Valley. This road to the coal field can be traveled the year around. Although the snow-

Jan 1, 1950

By F. H. Wilson, M. L. Kronberg

The low temperature recrystalliza-tion of very heavily rolled copper produces a fine grained structure with a high degree of preferred orientation. Additional heating to within a few hundred degrees of the melting point may induce an abrupt and pronounced increase in the grain size, with the resulting crystals having new orientations. This behavior at high temperatures is commonly termed "secondary recrystallization." Several investigations have dealt with the phenomenon arid have served to bare many features of the beha~ior.1-4 In general,observations have been made on the sizes and shapes of the grains, and data have been presented showing the existence of an induction period in isothermal experiments. Although it has been well established that the orientation before the change is statistically (100) 10011, the so-called "cubically aligned" texture, there is no such agreement on the orientation after the change. For example, Dahl and Pawlek1 describe it as being equivalent to an approximately 30" rotation about the [l00] axis of the ideal cubic texture which is parallel to the rolling direction, the resulting orientation being near (210)[001]; and Cook and Richards2 find an orientation of approximately (110)[L12]. Since the completion of most of the work to be reported in this paper, Rowles and Boas3 have published their ver] illuminating paper on "secondary recrystallization," in which they present convincing evidence for a third orientation and show that their esperiments give no evidence for either of the other two orientations. The orientation is described as equivalent to an approximately 30° rotation about a [ 111] pole of the ideal cubic orientation. The existence of a variety of reported orientations is not unique for copper, for a similar state of affairs exists for other systems that have been studied— aluminum, nickel, nickel-iron alloys, and others. It seems therefore that the existence of this variety does not necessarily constitute a contradiction, but rather indicates that different experimental conditions yield different results. The fundamental nature of the phenomenon has not been elucidated. However, it has been generally recognized that the large grains could be the end product of growth of a few select grains already existing in the sample in minor amounts—too small to allow detection—or that entirely new ones could be formed by a process of nu-cleation and growth. Existing experimental evidence does not distinguish between these two most apparent possibilities. Nevertheless, the former has been more generally favored largely because our current understanding of the state of an annealed metal has not made it seem reasonable to expect a nucleation event to occur at temperatures above those required for the primary recrystallization. Observations on the Preparation and Heating of Twin-bearing Cubically Aligned Copper The starting material used throughout. the investigation was a bar of OFHC copper, forged and annealed at 950°C. Visual inspection showed the grain size to be around 0.5 mm, and did not disclose any preferred orientation. A chemical analysis showed the following composition: Cu + Ag— 99.99 Pct S — 0.005 pct 0 — <0.005 pct For the preparation of cubically aligned copper, ¾ in. thick slabs were cut from the bar, heavily pickled in concentrated HNO3 and cold rolled to sheets about 0.012 in. thick. The reduction in thickness was approximately 98.5 pct. Standardized annealing techniques were followed. Samples to be heated were lightly dusted with alumina in order to prevent sticking and then sandwiched between 1/16 in. copper plates. The resulting sandwich was heavily wrapped with copper sheet, and then annealed in air. The protection was such that only very thin films of oxide were formed. That the associated light oxidation of the samples had no specific effect on the recrystallization behavior was shown by the similar results that could be obtained on annealing in highly purified and dried hydrogen. Two methods were used in bringing samples to temperature: (1) by placing the package directly in the furnace at temperature and (2) by placing the package in the furnace at room temperature, and then slowly increasing the temperature. The corresponding heating rates are illustrated in Fig 1, and will be referred to as "rapid" and "slow," respectively. Unless specified otherwise, all anneals will be of the former type. Metallographic examination was made on samples prepared by electrolytic polishing and etching as described in the Metals Handhook.* STRUCTURES FOUND BEFORE "SECONDARY RECRYSTALLIZATION" OCCURS Annealing the rolled material for 1 hr at 400°C produced a heavily twinned, cubically aligned structure, the grain size being of the order of 0.03

Jan 1, 1950

By James F. Neill, O&apos

Investigation of the Gilley fluorite deposit was based upon examinations made by several of the Bureau&apos;s mining engineers. Fluorspar was found in the dump talus of sloughed and water-filled trenches and shafts, and there were indications that faulting or other dynamic distortions favorable to deposition of this mineral in minable quality and quantity might exist. The inference was based upon a field study of the area and its comparison with fluorspar deposits in Kentucky. The proximity of this deposit to the iron furnaces at Gadsden and Birmingham was a factor that influenced its investigation, as the demand for metallurgical grades of this critical mineral is acute. The present supply for the district is obtained from out-of-State sources, and the value of any local deposit would be enhanced by the saving in freight charges. The Gilley fluorspar deposit is 17 miles east of Gadsden and 50 miles northeast of Birmingham, Ala. Mineral deposits occur as thin veinlets and small bunches of fluorite in upturned bode of siliceous limestone. The ore-bearing structure is a reverse fold, and the mineral deposit appears as a replacement along crumbled zone fractures of the contorted limestone.

Jan 1, 1950

Approximately half of all the fuel energy used in the United states is now pro-vided by oil and natural gas. A persistent and rapid growth in energy demand during the last 3 decades has been absorbed largely by the liquid and gaseous rather than solid fuels. In 1948 the energy provided by coal was substantially the same as in 1920. Meanwhile, the use of oil and natural gas each had increased fivefold. On a per capita basis, the change is more significant. Coal consumption has dropped from about 6 tons per person to 4-1/2 tons, while oil has increased from 4-1/3 barrels to 14-1/3, and natural gas from 7,500 cubic feet to about 35,000. These facts would have only academic interest if the United States had unlimited supplies of all fuels. However, while the Nation&apos;s reserves of coal are adequate to meet our needs for centuries, those of oil and natural gas appear limited. It is obvious, therefore, that the security of our liquid-fuel position would be greatly enhanced if the supply could be based in an increasing degree on solid fuels, such as coal and oil shale, which make up more than 95 percent of our fuel reserves, instead of natural oil and gas. In addition, this would create new employment and help to stabilize the market for coal, which may be facing comparatively bleak prospects in the near future unless its position with respect to other fuels is improved.

Jan 1, 1950

By Herbert Clark Hoover, Lou Henry Hoover

PREVIOUSLY I have dealt with the methods of separating silver from copper. There now remains the portion which treats of solidified juices ; and whereas they might be considered as alien to things metallic, nevertheless, the reasons why they should not be separated from it I have explained in the second book. Solidified juices are either prepared from waters in which nature or art has infused them, or they are produced from the liquid juices themselves, or from stony minerals. Sagacious people, at first observing the waters of some lakes to be naturally full of juices which thickened on being dried up by the heat of the sun and thus became solidified juices, drew such waters into other places, or diverted them into low-lying places adjoining hills, so that the heat of the sun should likewise cause them to condense. Subsequently, because they observed that in this wise the solidified juices could be made only in summer, and then not in all countries, but only in hot and temperate regions in which it seldom rains in summer, they boiled them in vessels over a fire until they began to thicken. In this manner, at all times of the year, in all regions, even the coldest, solidified juices could be obtained from solutions of such juices, whether made by nature or by art. Afterward, when they saw juices drip from some roasted stones, they cooked these in pots in order to obtain solidified juices in this wise also. It is worth the trouble to learn the pro- portions and the methods by which these are made. I will therefore began with salt, which is made from water either salty by nature, or by the labour of man, or else from a solution of salt, or from lye, likewise salty. Water which is salty by nature, is condensed and converted into salt in salt-pits by the heat of the sun, or else by the heat of a fire in pans or pts or trenches. That which is made salty by art, is also condensed by fire and changed into salt. There should be as many salt-pits dug as the circumstance of the place permits, but there should not be more made than can be used, although we ought to make as much salt as we can sell. The depth of salt-pits should be moderate, and the bottom should be level, so that all the water is evaporated from the salt by the heat of the sun. The salt-pits should first be encrusted with salt, so that they may not suck up the water. The method of pouring or leading sea-water into salt-pits is very old, and is still in use in many places. The method is not less old, but less common, to pour well-water into salt-pits, as was done in Babylon, for which Pliny is the authority, and in Cappadocia, where they used not only well-water, but also spring-water. In all hot countries salt-water and lake-water are conducted, poured or carried into salt-pits, and, being dried by the heat of the sun, are converted into

Jan 1, 1950

By P. R. Sperry, P. A. Beck, J. Towers

Dahl and Pawlek1 found that electrolytic copper develops extremely coarse grains at 1000°C after about 90 pct reduction by rolling. This coarsening occurs only under conditions of penultimate grain size, deformation, and alloying which lead to the "cube" recrystallization texture.l,2,3,5 The peculiar angular shapes and straight grain boundaries of the coarse grains were noted by several investigator.1,4,5 On the other hand, coarsening in Fe-containing aluminum or in AI-Mn alloys8 does not depend on a "cube" (or any well developed) recrystallization texture. It is true that increasing deformation by rolling, and, therefore, an increasingly well developed re-crystallization texture, are associated with decreasing incubation periods of coarsening.6-7-8 Nevertheless, coarsening readily develops in aluminum even after only 30 pct reduction by rolling, where the recrystallization texture is very weak.6,8 Also, coarsening was observed by Jeffries9 many years ago in sintered thoriated tungsten, which presumably has no preferred orientation. In all these cases coarsening is associated with grain growth inhibition by a dispersed second phase.8,9 The annealing temperature has to be suficiently high to overcome the inhibition at a few locations. But if it is too high, growth starts at many points, and the resulting grain size becomes much smaller.9 Normally, the coarse grains are more or less equiaxed, and the boundaries have a typical ragged appearance.6.8 Cook and Macquarie4 demonstrated that, in addition to the texture-dependent coarsening previously found at 1000°C,l electrolytic tough pitch copper may also coarsen at 800°C after 50 pct reduction by cross rolling. The coarse grains formed under such conditions have rounded shapes and ragged boundaries, like those in aluminum. When the annealing temperature is higher, the tendency for their formation decreases. All these observations suggest that the coarsening at 800°C is associated with inhibition by a second phase. Actually, coarsening at 800°C after 50 pct reduction by cross rolling was observed only in tough pitch copper,4 which contains Cu2O particles. On the other hand, the texture-dependent 1000°C coarsening occurs in both tough pitch and oxygen-free copper;4 it does not appear to depend on the presence of a dispersed second phase. However, the interpretation of the 800°C coarsening in Cu after 50 pct rolling as an inhibition-dependent process, similar to the coarsening in A1-Mn alloys, is somewhat weakened by the fact that this coarsening was reported4 to occur only after cross rolling, and not after straight rolling. It was, therefore, decided to re-examine this question. A 1 in. diam electrolytic tough pitch copper rod, No. 2 hard drawn, was annealed for 20 min at 700°C, rolled to 0.5 in., annealed 10 min at 700°C, and straight rolled to 0.064 in. It was then given a penultimate anneal of 20 min at 500°C and it was cut into four sections, which were given final reductions by straight rolling as follows: A 30 pct reduction of area B 50 pct reduction of area C 70 pct reduction of area D 90 pct reduction of area Specimens cut from the four sections were finally annealed at 800°C in an oxidizing atmosphere. Strip A remained fine grained up to 10 hr, but the specimen annealed 12 hr consisted of only 2 large grains. Strip B had a few scattered large (1/2 to 3/4 mm) grains after 1 min, although the balance of the specimen consisted of fine grains of about 0.02 mm. After 5 min there were several 10 to 15 mm grains present, and after 1 hr strip B was completely coarsened. The coarse grains had the same characteristics (see Fig 1) as those obtained by Cook and Macquarie at 800°C after cross rolling. Strip C had several grains of 0.05 to 1 mm after 1 min, but it was still largely fine grained after 12 hr. After 48 hr it consisted entirely of grains of about 0.5 to 4 mm, with an extraordinarily large number of twin bands. Strip D remained com- pletely fine grained after 4 hr at 800°C. These results indicate that, in the deformation range of 30 to 70 pct reduction, the incubation period for coarsening as well as the rate of growth and the final size of the coarse grains decreases with increasing deformation. Similar

Jan 1, 1950

By A. L. Engel

Many western ores containing ;old, silver, and copper can be mined and concentrated at a profit only when the recovery of those metals is high and treatment costs are low. Usually, ores containing easily dissolved copper minerals, or copper minerals that become soluble to some extent through oxidation during treatment, present a real problem in cyanidation. Copper cyanide compounds are formed that tend to &apos;precipitate and that cannot yield regenerated cyanide and metallic copper on contact with zinc. This results not only in some loss of copper through solution in cyanide, but in excessive consumption of cyanide above the amount required for the extraction of Gold and silver. Any moans, therefore, of minimizing the: loss of cyanide while at the same time effecting high recoveries of the several values contained in the ore is of wide interest. A sample of typical low-grade ore of gold, silver, and copper, containing copper-sulfide minerals, was obtained from the MacLaren Gold Mines Co., Cooke, Park County, Mont., for laboratory investigation by flotation and cyanidation.

Jan 1, 1950

By Lowell B. Moon

Concern over possible wartime shortages finally resulted in passage of the Strategic Materials Act in 1939. As authorized by one section of this legislation, the Bureau of Mines proceeded to investigate deposits of seven strategic minerals with the objective of developing tonnages of low-grade material that could be mined in an emergency. During the war, the size of the program and the number of strategic minerals were increased, and the objective was the more immediate one of aiding production. Since the war, the size of the program has been reduced, but the number of minerals on the strategic list continues to be large. The objective has returned to that of 1939. In the course of the program, more than 10,000 examinations were made and about 1,300 projects were run on deposits of 33 different commodities. A considerable contribution to war production was made in six of the commodities investigated, and a minor contribution was made in twelve others. Substantial reserves have been indicated in 19 minerals. Private interest is currently active in some of the deposits developed in 14 commodities.

Jan 1, 1950