Search Documents

By L. T. Stanley

A method is described whereby the behavior of the front is approximated when gas is injected into a thick reservoir having reasonably homogeneous properties. The method is applied to the Abqaiq field of Saudi Arabia. The producing member is the Arab-D, a high-permeability calcarenite which has no continuous betlding planes. Field performance indicates the injected gas to be partially miscible with the reservoir oil because gas volume factors experienced are lower than those predicted by the gas law. Eqlrilibril~m calculations confirnz ihis and also show that the volume factor may vary appreciably, depending on the relative quantities of oil and gas in contact in the reservoir; consequently, volutnetric balances are made for the purpose of determining the behavior of the gas volume factor during injection history. The effect of gravity segregation on position and shape of the gas front is approximated by dividing the producing section into three zones vertically and tracing the movement of the average interface in each zone, with counterflow of oil and gas taking place betweell zones behind the front. This results in a gas front that advances more rapidly along the top of [he formation than along the base, producing an "umbrella" effect in cross section that becomes more pronounced as the front progresses. The calculations cover the gas-injection period of Abqaiq field history through 1958, and the position of the gas front is plotted at one-year intervals. Finally, some comparisotls between the calcrlated fronial position and the gas-oil contact as Measured by neutron logs are made. INTRODUCTION Fig. 1 is a structure contour map of the Abqaiq field. For analytical purpcses, the field has been divided into two areas designated A and B, as shown on the map. Gas injection into Area A was begun in early 1954 into two wells located near the crest of the structure on the north-south axis of the anticline. During the period covered by this paper, the average injection rate has been 122 MMscf/D with a maximum sustained rate of 160 MMscf/D. The reservoir pressure has been maintained at 2,450 psig since start of gas injection. The reservoir originally was undersaturated but, prior to pressure maintenance, the pressure was drawn below the bubble point in most of the Area A section, creating an in-place free-gas saturation of 8 per cent at the crest of the structure. The average critical gas saturation is 13 per cent established by laboratcry core tests. That the entire reservoir remained below critical gas saturation prior to gas injection is borne out by the fact that none of the crestal wells have exhibited high gas-oil ratios during production history. The Area A reservoir is a carbonate section about 200-ft thick having average porosity and permeability of the order of 22 per cent and 500 md, respectively. The productive horizon is the Arab-D member of Jurassic age and is encountered at an average depth of

The February General Meeting of the Institute was held in Kelvin House, Johannesburg, on 19th February, 1969 at 4.30 p.m. Mr R. C. J. Goode (President) was in the Chair. There were also present forty-six Members, including Messrs H. E. Cross, A. R. C. Fowler, P. Lambooy, D. G. Maxwell, Dr J. T. McIntyre, Messrs J. A. Nixon, V. C. Robinson and P. W. J. van Rensburg (Council Members), Messrs G. Abdinor, H. F. Allan, R. E. Barnes, M. M. Bayley, J. K. Boyd, R. R. M. Cousens, R. E. F. Cowley, D. Savile Davis, H. J. Davisson, C. T. Fenton, J. Fergusson, J. Fritz, M. L. Fitzgerald, J. M. Gosnell, J. C. Hall, S. A. Hancox, D. M. Jamieson, Dr D. G. Krige, Messrs J. E. V. Leeuwen, A. Louw, C. F. Louw, B. H. L. Leach, R. B. MacGillivray, C. S. McPhail, E. Margo, G. G. Nicolson, E. Pavitt, M. P. Pearse, F. O. Read, Dr M. D. G. Salamon, Dr H. S. Sichel, Messrs D. Storrar, S. G. Taussig, A. H. Taute, E. B. Viljoen and P. A. von Wielligh. Sixteen Associate Members, including Messrs S. T. Baron, W. M. Fitzpatrick, M. R. Fuller-Good, P. R. Garcia, H. G. Gericke, P. D. Hatfield, R. Hemp, G. S. Lee, Miss V. E. Marting, Messrs A. H. Munro, R. C. Power, O. F. Rheeder, G. C. Thompson and N. Zolezzi. Two Graduates, Messrs D. Bosley and J. C. Sutherland. Three Affiliates, Messrs R. K. Briggs, A. B. Cook and G. M. Thain. One Student, Mr P. W. Henrard. Twenty-three Visitors, including Messrs N. J. W. Bell, R. G. Bushell, A. Bryan, J. F. Cillie, C. M. de Beer, Dr F. H. Deist, Messrs D. S. Drake, P. G. du Plessis, R. W. Hodgson, D. M. Hawkins, S. C. H. Kearns, M. D. Labuschagne, L. Munro,R. Murchison and L. Robinson. Secretary, Mr D. C. Visser. Total present: Ninety-two. OBITUARIES The President: "It is my sad duty to announce the death of the following members of the Institute. Edward Frank Jud Bulman, Life Member, who joined the Institute in 1931 and passed away on 7th November, 1968. Elmar Fenton Chapin, Member, who joined the Institute in 1941 and passed away on 17th November, 1968. Solly Rabinowitz Rabson, Member, who joined the Institute in 1944 and passed away on 13th February, 1969. Mr. Rabson was the holder of two certificates of merit for papers presented to the Institute.

By J. Paraszczak

Underground metal mining involves many challenges. Economic slowdown, tough international competition and sometimes volatile metal prices put constant pressure on mine operators to increase productivity and to reduce production cost. At the same time, countries such as Canada, the United States and Australia are experiencing skilled labor shortages that might even stall development of certain mine projects. Furthermore, some stages of underground production take place in particularly hazardous environments where the safety and health of miners is at risk. Automation of some processes in underground mining is one of the promising avenues to alleviate some of these problems. Loading and haulage are among the most critical operations and areas where implementation of autonomous vehicles has been targeted. However, although health and safety issues are a primary driver to opt for automation, the latter should ensure an acceptable level of productivity and pro?tability. With this in mind, this article focuses on the factors affecting operational effectiveness of autonomous underground loading and haulage equipment and the means to maximize it.

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jason Navoyski, Jennica L. Bellanca, William J. Helfrich

Recent advances in computing, rendering, and display technologies have generated increased accessibility for virtual reality (VR). VR allows the creation of dynamic, high-fidelity environments to simulate dangerous situations, test conditions, and visualize concepts. Consequently, numerous products have been developed, but many of these are limited in scope. Therefore, the National Institute for Occupational Safety and Health researchers developed a VR framework, called VR Mine, to rapidly create an underground mine for human data collection, simulation, visualization, and training. This paper describes the features of VR Mine using self-escape and proximity detection as case studies. Features include mine generation, simulated networks, proximity detection systems, and the integration and visualization of real-time ventilation models.

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 26th August, 1970, at 4.15 p.m. Mr. J. K. E. Douglas (President) was in the Chair. There were also present sixty-three Fellows, thirty-five Members, one Graduate, eight Associates, five Students and nineteen Visitors, making a total of one hundred and thirty-two. The President declared the meeting open at 4.20 p.m. OBITUARIES The President: 'It is my sad duty to announce the deaths of the following members of the Institute. Dr J. A. Papenfus, Fellow, who joined the Institute in 1942 and passed away on the 28th of May, 1970. Mr D. G. Beadle, Fellow, who joined the Institute in 1946 and passed away on the 17th of June, 1970. Gentlemen, Derek Beadle was very well known in this Institute. His papers on dust will be remembered and, at the time of his untimely death, he was one of our assistant editors. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence.' MINUTES The President: 'May we confirm the minutes of the General Meeting held on 15th April, 1970, as published in the July, 1970, issue of the Journal'. Agreed. WELCOME TO VISITORS The President: 'Ladies and Gentlemen, we are honoured this afternoon by the presence of many distinguished guests and I extend to you all a most cordial welcome. We are happy to have with us Dr A. A. von Maltitz, President of the Chamber of Mines of South Africa, who is also Honorary President of this Institute. We also have one of our Honorary Vice- Presidents, Mr T. L. Gibbs, the Government Mining Engineer; Mr D. E. Hamm, President, Institution of Certificated Mechanical and Electrical Engineers, S.A.; Mr S. C. M. Naude, Director, Witwatersrand Technical College; Mr I. R. G. Stephen, Senior Vice-President, The S.A. Institute of Electrical Engineers; Mr G. M. Tompkins, President, The S.A. Institution of Mechanical Engineers; Professor P. B. Ackermann, President of the Geological Society of S.A.; Mr A. S. Robinson, Vice-President of the S.A. Institute of Civil Engineers; Professor W. Mare, President of the Institute of Land Surveyors of the Transvaal; Mr B. D. Charlton, President of the S.A. Institute of Assayers and Analysts; Mr R. Hemp, The President, The Mine Ventilation Society of S.A.; Mr L. J. Prince, The President, The S.A. Association of Mine Managers; Mr J. Botha, The President, The S.A. Institute of Foundrymen; Mr G. Niterl, The President, The Institute of Welding; Mr M. R. Gericke, President, S.A. Council of Professional Engineers; Mr N. A. Honnet, Chairman, Orange Free State Branch; Mr P. R. C. Cooke, Chairman. The South African Chemical Institute (S. Tvl' Section). Gentlemen, we are very honoured indeed, to have these distinguished gentlemen with us this afternoon, as our honoured guests. We are also pleased to have with us, one of our Honorary Fellows, Mr F. G. Hill, and several Past-Presidents. I also extend a very warm welcome to all our lady guests and to all our other visitors.' MEMBERSHIP The President: 'I have pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership in the following grades: NEW APPLICATIONS Fellows: Herbert Dalton-Brown, Stephen William Morel. Members: Clive Lester Workman-Davies, Basil James Russell Botha. Students: Timothy Nigel Watson, John William Hairbottle. I wish to welcome the new members to the Institute and to congratulate those members who have been transferred to a higher grade.' ANNUAL REPORTOFTHE COUNCILAND ACCOUNTS FOR THE YEAR ENDED 30th JUNE, 1970 The President: 'I now have pleasure in presenting to you, the Annual Report and Statement of Accounts for the year ended June, 1970. These have been handed to you this afternoon and, as is customary, I propose they be taken as read. Before moving their adoption, however, I would like to refer to some of the salient features, leaving as is usual, the task of dealing with the finances, to our Honorary Treasurer. It is encouraging that membership has continued to grow, and now stands at 1,613, an increase of 61 over last year's total. Your Council, however, is aware that there are still people in our mining and metallurgical industries, who could qualify for membership, but who have not yet joined the Institute. A drive to increase membership was accordingly organised, and members of Council were given the responsibility for campaigning in sections of industry, and for publicising the objectives and advantages of belonging to the Institute. Up to now there has not been much reaction to this campaign, but I hope we will see results in the coming year. At the same time, Council has recognised the need for change in the conduct of the Institute's affairs in order to meet the changing needs of our membership. Our members, both mining and metallurgical, are in the first place, geographically more widely dispersed than they used to be, and secondly, with the growth of the metallurgical industry, their technical interests are now more diversified. The Institute must cope with these changing needs if we are to continue to perform a useful function. The

By W. F. Visser

The growing availability of information and data analysis capabilities provides new opportunities for improving the performance of operations. By using real-time measurements and artificial intelligence, it is possible to respond faster to changing conditions, while accurate and timely information permits the rapid evaluation of changes and fast business improvement decisions. This paper presents a blueprint for system alignment, organizational design and management practices to leverage these developments in performance-driven operations management in mining and mineral processing.

By Richard J. Mainiero

Traditional techniques for the experimental determination of toxic fumes produced by the detonation of high explosives are not applicable to blasting agents. To detonate properly, blasting agents require confinement, a significant booster, charge diameters of 3 inches (7.5 cm) or greater, and charge lengths greater than two-times the charge diameter. Without these conditions, blasting agents will not detonate at full order, leading to a misrepresentation of the gaseous products. A facility for detonating large, confined charges in a controlled volume has been constructed at the Pittsburgh Research Center’s Experimental Mine. The facility consists of a portion of mine entry (once used for full-scale mine explosion research and demonstrations) enclosed between two explosion proof bulkheads. Total volume of the chamber is 9,666 ft (274 m). The chamber is equipped with an air circulating system and is3 3vented using the mine's airflow. Up to 10-pound (4.5-kg) charges can be detonated in the chamber using a variety of confinements. For a typical test, the blasting agent is confined in a 4-inch (10-cm) schedule 80 steel pipe and initiated by a 3-inch (7.5-cm) diameter, 1-inch (2.5-cm) thick Pentolite booster. This combination of confinement and initiation yields a detonation velocity of about 4,000 m/sec for ANFO. This velocity is in line with that measured for blasting in the field. Twenty four 2-inch thick steel plates are suspended around the pipe bomb to stop shrapnel that would otherwise seriously damage the chamber. Following detonation of an explosive in the chamber, a circulating fan is run for about 10 minutes to uniformly mix the chamber atmosphere. Fumes samples are taken out of the chamber through 1/4-inch (0.6-cm) Teflon or polyethylene2tubes for analysis. The fumes are analyzed using bubblers or Vacutainers to collect samples for analysis by the analytical chemistry lab. The technique described here has been employed to determine the fumes produced by the detonation of a variety of ANFO formulations and commercial explosives. This technique may be developed as a standard test to measure fumes produced by blasting agents or may be used to provide data with which to develop a computer model that will reliably predict the expected fumes production based on chemical composition.

The Annual General Meeting of the Institute was held in Kelvin House, Johannesburg, on Wednesday, 26th August, 1970, at 4.15 p.m. Mr. J. K. E. Douglas (President) was in the Chair. There were also present sixty-three Fellows, thirty-five Members, one Graduate, eight Associates, five Students and nineteen Visitors, making a total of one hundred and thirty-two. The President declared the meeting open at 4.20 p.m. OBITUARIES The President: 'It is my sad duty to announce the deaths of the following members of the Institute. Dr J. A. Papenfus, Fellow, who joined the Institute in 1942 and passed away on the 28th of May, 1970. Mr D. G. Beadle, Fellow, who joined the Institute in 1946 and passed away on the 17th of June, 1970. Gentlemen, Derek Beadle was very well known in this Institute. His papers on dust will be remembered and, at the time of his untimely death, he was one of our assistant editors. As a mark of respect to the memory of the deceased and in sympathy with the bereaved, I would ask you to rise and observe a few moments' silence.' MINUTES The President: 'May we confirm the minutes of the General Meeting held on 15th April, 1970, as published in the July, 1970, issue of the Journal'. Agreed. WELCOME TO VISITORS The President: 'Ladies and Gentlemen, we are honoured this afternoon by the presence of many distinguished guests and I extend to you all a most cordial welcome. We are happy to have with us Dr A. A. von Maltitz, President of the Chamber of Mines of South Africa, who is also Honorary President of this Institute. We also have one of our Honorary Vice-Presidents, Mr T. L. Gibbs, the Government Mining Engineer; Mr D. E. Hamm, President, Institution of Certificated Mechanical and Electrical Engineers, S.A.; Mr S. C. M. Naude, Director, Witwatersrand Technical College; Mr I. R. G. Stephen, Senior Vice-President, The S.A. Institute of Electrical Engineers; Mr G. M. Tompkins, President, The S.A. Institution of Mechanical Engineers; Professor P. B. Ackermann, President of the Geological Society of S.A.; Mr A. S. Robinson, Vice-President of the S.A. Institute of Civil Engineers; Professor W. Mare, President of the Institute of Land Surveyors of the Transvaal; Mr B. D. Charlton, President of the S.A. Institute of Assayers and Analysts; Mr R. Hemp, The President, The Mine Ventilation Society of S.A.; Mr L. J. Prince, The President, The S.A. Association of Mine Managers; Mr J. Botha, The President, The S.A. Institute of Foundrymen; Mr G. Niterl, The President, The Institute of Welding; Mr M. R. Gericke, President, S.A. Council of Professional Engineers; Mr N. A. Honnet, Chairman, Orange Free State Branch; Mr P. R. C. Cooke, Chairman. The South African Chemical Institute (S. Tvl. Section). Gentlemen, we are very honoured indeed, to have these distinguished gentlemen with us this afternoon, as our honoured guests. We are also pleased to have with us, one of our Honorary Fellows, Mr F. G. Hill, and several Past-Presidents. I also extend a very warm welcome to all our lady guests and to all our other visitors.' MEMBERSHIP The President: 'I have pleasure in announcing that the names of the following candidates, having been published in accordance with By-Law 5.2.2, Council has elected them to membership in the following grades: NEW APPLICATIONS Fellows: Herbert Dalton-Brown, Stephen William Morel. Members: Clive Lester Workman-Davies, Basil James Russell Botha. Students: Timothy Nigel Watson, John William Hair-bottle. I wish to welcome the new members to the Institute and to congratulate those members who have been transferred to a higher grade.' ANNUAL REPORTOFTHE COUNCILAND ACCOUNTS FOR THE YEAR ENDED 30th JUNE, 1970 The President: 'I now have pleasure in presenting to you, the Annual Report and Statement of Accounts for the year ended June, 1970. These have been handed to you this afternoon and, as is customary, I propose they be taken as read. Before moving their adoption, however, I would like to refer to some of the salient features, leaving as is usual, the task of dealing with the finances, to our Honorary Treasurer. It is encouraging that membership has continued to grow, and now stands at 1,613, an increase of 61 over last year's total. Your Council, however, is aware that there are still people in our mining and metallurgical industries, who could qualify for membership, but who have not yet joined the Institute. A drive to increase membership was accordingly organised, and members of Council were given the responsibility for campaigning in sections of industry, and for publicising the objectives and advantages of belonging to the Institute. Up to now there has not been much reaction to this campaign, but I hope we will see results in the coming year. At the same time, Council has recognised the need for change in the conduct of the Institute's affairs in order to meet the changing needs of our membership. Our members, both mining and metallurgical, are in the first place, geographically more widely dispersed than they used to be, and secondly, with the growth of the metallurgical industry, their technical interests are now more diversified. The Institute must cope with these changing needs if we are to continue to perform a useful function. The

By D. G. Krige

D. G. Krige: The stimulating contributions from Messrs Cooke, Curtis, Martus, Johnston, Van Wyk, Van Rensburg and Wroth are appreciated by the author and provide clear evidence of the importance not only of the principle of assistance to gold mines, but also of its scope and form. In general all the arguments, raised by Messrs Cooke, Martus and Johnston in favour of extending the scope of the new assistance scheme can be accepted as sound.

By William P. Blake

When we consider the efforts made in Europe to promote the physical and moral well-being of the working classes, the question is suggested whether in this country, where, theoretically, every man is peculiarly the arbiter of his own destiny, we may not be too prone to expect every man to take care of himself, and neglect to make those provisions for the welfare of the employed, demanded alike by enlightened economy and humanity. In the older countries, where the disproportion between capital and labor is greater, and the working classes are more dependent, their welfare largely occupies the attention of employers. The subject is involved in the problem of the just relations of capital and labor, and we are rapidly approaching the time, if we have not already reached it, when a generous paternal interest in the welfare of the employed should be more generally manifested. It is a subject which is of special importance to mine-owners and engineers in this country, especially to those located in the coal regions. My own attention has been particularly directed to it by a visit made to the Hassard collieries, a few miles from Liège, Belgium, under the direction of M. Andrimont. This celebrated engineer has established a comfortable home for the miners near the mouth of the shaft of the mine. It has been highly successful and beneficent in its results, and may to a great degree be regarded as a model for such undertakings. It is known as ((Hotel Louise," this being the name of Madame d' Andrimont, who laid the corner-stone of the building April 4th, 1871. The structure is of brick, upon three sides of a square, and

By Douglas W. Fuerstenau, Pradip Pradip

The design and development of selective flotation collectors has been the key to the remarkable success of flotation in beneficiating complex, difficult-to-process ores. Sustained research efforts in the field over the past hundred years have led to delineating the scientific basis of selective mineral flotation in terms of the crystal chemistry and the surface and colloid chemistry of minerals including their solubility, and the aqueous solution chemistry of added reagents. It is now well-established that the electrical double layer theory (EDL) is the most powerful means of quantifying the relative strength of mineral-reagent interactions in the case of nonsulfide minerals. We illustrate the utility and the power of the EDL in delineating the science underlying selective mineral flotation with the help of a few examples taken from our own work, in particular on the selective flotation of rare-earth minerals (bastnaesite) from associated semisoluble minerals (barite and calcite) using alkyl hydroxamate collectors and the flotation separation of lithium-containing minerals (spodumene) from associated alumino-silicate minerals with oleate (fatty acids). Both of these mineral separation systems are of contemporary research interest and of immense value to the industry today. Recent advances in utilizing molecular modeling computations, particularly in the context of quantifying the effect of crystal chemistry and the relative distribution of adsorption sites available on mineral cleavage planes, are also reviewed.

By Russell Frith

The entire subject area of micro-seismic events due to stored strain energy, as distinct from gas-driven coal outbursts, can be readily sub-divided into firstly events with their energy source from within the coal seam (termed “bursts”) and secondly, event with their energy source outside of the coal seam in either the overburden and/or floor strata. The reason for sub-dividing micro-seismic events in this manner is that if the causation mechanisms and associated geotechnical conditions are materially different, then effective pre-mining predictions and subsequent operational controls may also differ. Attempting to explain a multitude of micro-seismic event types without consideration of varying source mechanisms will inevitably lead to inadequate causal explanations and effective controls.

By Pratt Rogers, Aaron Young

Digital transformation (DT) is the process by which entities adapt themselves to modern technology. As digital technology becomes more prevalent (automation, cameras, sensors, touchscreens, artificial intelligence, etc.), there will be increased pressure on companies to leverage it for additional gains. For many companies in the mining industry, this will involve overcoming a steep learning curve. Furthermore, as the long-term success of the mining industry is dependent on a labor force with new skills (data management, analytics, digital literacy, etc.), new curriculum will need to be appended to the mining engineering discipline. This paper considers the mining industry’s need for DT. Then, it presents a three-part review of the foundational components of the DT process–ubiquitous data, connectivity, and decision making. Finally, it provides a discussion on the future of DT in mining as well as a research direction, which identifies the need of academia to provide support for mining companies in the form of both research and the education of digitally literate, dynamically capable mining engineers into the coming decades.

By T. Gupta, T. Ghosh

Rare earth elements (REEs) and their compounds are essential in a multitude of mundane and sophisticated applications such as renewable energy technologies, catalysts, medicine, and defense applications. The global supply deficit could be attributed to the destabilization of REE market that has, as a result, incentivized indigenous production of REEs. Cost-effective and environmentally benign opportunities are being explored for the production of REEs from non-conventional mineral sources including coal and coal by-products to stabilize the supply chain. Coal from Healy coal mine and Wishbone Hill deposits in Alaska have been quantified for REEs and were found to possess elevated total REE concentrations as compared to world average levels (60– 70 ppm). The objective of the study was to concentrate the REEs in the froth phase by froth-flotation of the fine size fraction (< 75 μm). A Box-Behnken design of experiment was employed to ascertain the main and interaction effects of operational parameters on response variable by analyzing 3D response surfaces. Experiments were carried out to maximize REE recovery and concentration by modeling and optimization of three operating variables (frother dosage, pulp density (% solids), and collector dosage). Based on the results, the optimum flotation conditions for maximum recovery at an elevated concentration of REEs in the froth fraction was obtained at 4.2% solids and 32.7 ppm of frother dosage for Healy sample and 10% solids and 37.9 ppm of frother dosage for Wishbone Hill coal sample. The quadratic relationship between the input and response variable was found to be independent of collector dosage suggesting good surface hydrophobicity and floatability of the two coal samples.

By J. M. Wempen, R. D. WEYHER, M. K. McCarter

Beam theory is a proxy for the behavior of intact, deforming roof strata above underground openings. Strong, stiff, intact strata have the ability to store significant strain energy when underground openings have large spans, as is typical of longwall operations. When strata fail, they may release some or all of this strain energy. Released energy is partitioned between fracture, thermal and seismic energy. The tensile failure surface in simply supported beams is predicted to be free of shear stress. This prediction and the kinematic inability of crack slip during fracture make significant dissipation of energy by friction unlikely.  In this study, the failure energy partitioning of specimens from the Nugget Sandstone formation is examined. Tensile fractures in specimens were induced using three-point loading tests. Elastic waves emanating from fracture events were recorded using an array of accelerometers. Accelerometers were placed within two crack lengths of the fracture surface, and the acceleration records are similar to strong motion seismic records. Spectral analysis was performed and used to develop synthetic, well-behaved, acceleration signals. Synthetic velocity signals were used to estimate radiated seismic energy generated by fracture. These estimates of radiated seismic energy demonstrate a potential means to constrain the minimum seismic partition. Fracture testing was performed on additional samples to estimate the fracture toughness of the sandstone. Synthesis of this data demonstrates a potential means to constrain a maximum seismic partition. Bounding the seismic partition for this type of fracture event could aid the detection and evaluation of seismicity emanating from longwall operations. Having better information about the location and magnitude of mining induced seismicity within longwall overburdens could lead to better understanding of extraction sequencing and rock behavior in general. These energy estimates also support the hypothesis that dissipation of thermal energy by friction is small in bending tensile failure.

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral-processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. When a sensor goes off calibration, it results in errors that can have a severe impact on plant economics. Classical statistical approaches fail to detect when errors are “subtle,” unless they grow and become large enough to be “gross,” whereas methods based on signal processing and artificial intelligence fail in dealing with the complexity of process fluctuations. Due to the sheer volume of sensors, undetected errors are not remedied until the next calibration, which on average are a year apart across all industries [1]. This research aims to detect such subtle errors (2 percent bias) in shorter time spans of about a month — rather than wait for errors to grow — using innovative data-mining techniques and algorithms.

By Isabel F. Barton, MarkD. Barton, Christian A. Rathkopf

Molybdenite is the world’s principal source of rhenium (Re), a critical element in multiple high-tech applications. However, the Re contents in molybdenite vary by orders of magnitude on scales ranging from single grains to whole deposits. In order to better understand the systematics of this variation and what geochemical factors control molybdenite Re concentration, and hence overall Re resources, we examine global patterns in molybdenite Re contents through a compilation of > 3000 measurements of Re in molybdenite from > 700 mainly ore-bearing moderate- to high-temperature hydrothermal systems of different types. Our results are similar to but expand on those of earlier studies. Rhenium concentration in molybdenite has a lognormal distribution and varies systematically with type of geologic system, intrusive lithology, and Mo grade. The lowest-Re molybdenite occurs in greisens (geometric mean 1 ppm ± a multiplicative standard deviation of 9), quartz vein-hosted W-Sn deposits (2 ± 5 ppm), unmineralized granites and granodiorites (12 ± 8 ppm), intrusion-related deposits (24 ± 8 ppm), and porphyry W-Sn deposits (16 ± 11 ppm). Rhenium is most enriched in molybdenites from volcanic sublimates (23,800 ± 5 ppm), with skarn Fe and Au (560 ± 5 ppm and 540 ± 3 ppm respectively) and porphyry Cu and Cu-Au deposits next (470 ± 4 and 430 ± 7 ppm respectively). Among porphyries, skarns, and quartz vein-hosted deposits, Re is most highly concentrated in molybdenites from Cu and Au systems and its concentration decreases systematically through Cu-Mo, Mo, Sn, and W deposits. In nearly all cases, molybdenites from systems associated with intermediate igneous rocks contain more Re than molybdenites from systems of the same type with more felsic rock associations. The disparity between Re contents of molybdenite in felsic and intermediate systems is largest for porphyries, quartz vein-hosted, and skarn deposits and is near zero for subeconomic or barren granite and granodiorite Mo systems; felsic intrusion-related deposits have slightly higher molybdenite Re than their equivalents associated with intermediate intrusions. In most systems, molybdenite Re content does not correlate with metal grade, but may have an inverse correlation with Au grade in intrusion-related deposits (based on a small number of data points) and does exhibit a strong inverse correlation with deposit Mo grade. Dilution of Re through larger amounts (higher deposit grades) of molybdenite explains about 40% of this correlation, but the relative enrichment of Re in molybdenite from low-Mo deposits must also reflect some selective enrichment of Re/Mo in porphyry Cu systems compared to porphyry Mo systems. We found no evidence for secular increase or other systematic temporal variation in molybdenite Re content. The data regarding the use of molybdenite Re content as a proxy for mantle influence are ambiguous. Nearly all observed empirical correlations can be traced back to differences in redox state and sulfide concentration, the two geochemical factors identified here and by previous experimental work as the controlling influences on Re mobility under hydrothermal conditions. Hydrothermal systems with reducing conditions (W- and Sn-rich) tend to have low molybdenite Re even though compiled whole-rock data indicate that their source rocks have as much or more Re as those of more oxidized systems (e.g., Cu-rich). Vapor-phase exsolution, crustal assimilation, and mixing with external fluids may all enrich molybdenite Re concentrations in individual deposits and deposit types, but their extent and importance in overall hydrothermal concentration of Re is uncertain. Thus, it appears that the available molybdenite Re resource in an ore deposit largely depends on how the deposit’s redox and sulfidation conditions have varied over time and space during the timespan of hydrothermal activity. Oxidized, high-sulfide conditions tend to concentrate Re in molybdenite, whereas reducing conditions tend to leave Re dispersed at low concentrations in the bulk rock.

By Weijie Wei, Jinwang Zhang, Shengli Yang

In longwall top-coal caving (LTCC) mining with an inclined seam, the recovery rate is low and equipment stability is poor due to the unbalanced top-coal drawing process. To address these problems, this paper proposes the dynamic group caving method (DGCM), whose basic premise is that when the drawn volume of top coal from a support reaches about half, the next support begins drawing top coal, and the drawing process between the two supports is half done. Using particle flow code (PFC), the caving mechanism of top coal under DGCM was investigated. The results are of significance to realize high efficiency and precise caving in LTCC mining with an inclined seam.

Dr Hanekom I would like to thank Dr Hanekom for a very valuable -contribution; it summarizes careful statistical test work which was an omission from the original paper. Minor manipulative details, the application of a finer measuring graticule and the reproducibility of the procedure are described and the author accepts with gratitude this ready-made answer to the first and second points of Dr Finkelstein&apos;s comments. Mr Williamson The author is indebted to Mr Williamson for historical background to early experiments with captive bubbles and it is conceded that the original paper described another avenue to an old flotation goal. The field of application is restricted and we would not work with all the material illustrated by Klassen and Mokrousov.1 The particles in Figure 74(a) are far too large and irregular; material in Figures (b) through (d) could be employed for semi-quantitative work in spite of obvious disadvantages; Figure 74(f) represents ideal conditions. We have studied this mineral-collector association in the size range given and results were satisfactory. For larger pick-up values than that illustrated an induction period of more than 0.01 second was required (actually 90 seconds for a maximum bubble load at pH 7.2 with 25 g/t oleic acid!). REFERENCE 1. KLASSEN,V. I. ANDMOKROUSOV,V. A., &apos;An Introduction to the Theory of Flotation,&apos; Butterworths, London, 128, Figure 74, (1963). Mr Slander and Mr Kooij Researchworkers in a practical mineral development laboratory may well ask what contribution yet another micro-technique can make to the problems of large scale ore flotation. The obvious answer is that there can be little or no direct translation of results obtained with a static system comprising air bubble and pure mineral concentrate to a dynamic multicomponent operation. However, for the rapid study of one mineral or variable some small scale apparatus must be employed. In the Anglo American Research Laboratory, the described semi-quantitative pick-up technique has filled a niche and requirement. For ourselves, the system represents a definite advance over the contact angle approach in that samples of minerals conventionally prepared in laboratory or plant may be used, which is a desired step nearer flotation. We bracket this pick-up apparatus with the Hallimond tube1,2 and evidence is now to hand that pick-up curves may often be related to flotation recoveries obtained from this tube with pure mineral samples and from the Fuerstenau glass cell3 with the total ore at low pulp densities. We would not wish to push the comparison of pick-up results past this stage for there is much published development work relating the Hallimond and Fuerstenau equipment to flotation on a larger scale. At the Anglo American Research Laboratory for example, a test in a Fuerstenau cell is often the final integrated step in laboratory investigations into the TORCO process. As these contributors rightly point out, pick-up tests can offer nothing towards the determination of optimum reagent dosage for large scale flotation. This is the function of bench-type flotation cells with up to 2 kg batches of ore. At this level, collector performance and consumption and physical properties of the froth are more comparable with large scale operation. The pick-up cell, Hallimond tube and Fuerstenau cell are essentially equipment from which the effect of control parameters can be derived. For the assessment of collector behaviour, the pick-up approach is rapid and economic and we offer here a pick-up contribution towards the flotation of Witwatersrand uraninite with anionic sulphonate collectors (Fig. 1). A large crystal of the local mineral was not available for contact angle measurements and owing to its low concentration in Witwatersrand gold-bearing reef, a small sample was laboriously obtained by tabling, superpanning and heavy medium separation. The pick-up values of a sized portion were determined by the described procedure in the presence of nine petroleum sulphonate collectors. Responses fell into two categories; "normal" curves (dotted lines) and a group of collectors which were very active at low concentration but showed depression of pick-up at the higher levels. The similarity in form of curves for collectors 1 and 3 was apparent and reagent 3 was found to be simply a diluent of 1. Otherwise, collector performance could not be related to either sulphonate content or molecular weight of the active constituent. However, reagent 2 gave the best performance in a bench flotation cell with regard to overall uranium distribution but, as predicted, reagent 1 yielded the best grades. Later pick-up tests with a similar class of collector have suggested that depression at high reagent concentrations may be due to "bubble armouring" whereby an hydrophilic air-liquid interface is produced which rejects mineral attachment. Prolonged investigations with the same mineral sample have not been required except for the study of uraninite which lasted for more than a year. Variation in pick-up response could not be detected over this period during which the mineral was stored under distilled water. The only visible change was a small efflorescence of lead sulphate, readily removed and decanted off after stirring with a glass rod in the sample tube. In its main role as a "trouble-shooter", the pick-up method is applied to fresh mineral samples taken from a flotation plant and soon discarded or from a current run in the ore-dressing laboratory. After production of a concentrate, a solvent cycle, as described in the original paper, may be required to remove heavy organics or other contaminants as when a sample has been taken from circuits containing detergents, grease or return flotation solutions. This solvent cycle will not remove chemisorbed collectors and we prefer not to work with minerals from flotation tailings or with pick-up cell discards. It has been thought preferable to answer the contributors&apos; other apprehensions with regard to sample preparation, activators, depressants and the physical properties of reagents in another paper on offer to this Journal. It covers pick-up investigations relating to the flotation of nickeliferous pyrrhotite at two Anglo American Corporation Mines, which approach seemed the correct orientation for a reply to another contributor to this paper.