Search Documents

By Bill Linville

Producing oil, gas, and coal in sufficient amounts to satisfy U.S. demands for fuels, electrical power, and chemicals promises to be one of the country's major challenges during the 1970's. Adding significantly to this challenge is the urgent task of satisfying soaring fuel and power demands without destroying the natural environment or jeopardizing long-range requirements for resources. The Bureau of Mines, U.S. Department of the Interior, is engaged in a comprehensive program of research to help industry meet this challenge. This report reviews the aims of the research program and accomplishments in 1970; the first 11 sections cover coal programs, nine sect ions are then devoted to petroleum, and the concluding five sections deal with oil shale research. Figure 1 shows the nationwide distribution of Bureau of Mines energy research installations; Full addresses are given in appendix A. Many of the publications resulting from the Bureau?s energy research efforts are discussed throughout the report; others are listed in appendix B.

Jan 1, 1971

Presented in this volume are the basic mining techniques and production operations associated with underground bituminous coal mining. Chapter 2, "Multiflow Process Charts", presents, in sketch form, a description of the various operations characteristic of conventional and continuous mining. In order to focus attention upon the major components and operations in each work cycle, certain items are not shown in the sketches, e. g., machine electrical cables, brattice, and rib posts. The elapsed time shown for each sketch is considered representative for the various work elements summarized by the sketch. More detailed work element times can be found in Chapter 3, "Typical Work Cycle Times", and Chapter 4. "Standard Time Data".

Jan 1, 1971

By Y. L. Su

Deterministic and stochastic simulation were combined to develop a computer model of an open pit mining system using bucket wheel excavators and related materials handling equipment. The model is closed and dynamic in the sense that information is fed back to control activities at various levels and reservoirs. The results of interaction between unit operations in one time interval determines overall system behavior for the next interval. Equipment performance curves and system profile characteristics rather than time studies are applied to determine the operation of each activity at any time period. For that part of system where performance is dictated by a random variable~ subjective probabilities are employed. Two stages of research were considered to formulate this model. Stage one involved the formulation of equipment sub-assemblies for the sequence of equipment moves along with related assignments and routines for information retrieval. The second stage of research combined all sub-assemblies into an integrated open pit mining simulator. The model is not tailored for any specific open pit operation but is readily adaptable to any system of surface mining including operations having a high degree of complexity. Questions answered by the model include: 1) system design and selection of equipment for a new mining operation; 2) analysis of existing operations for possible changes, additions or general

Jan 1, 1971

The strippable reserves of bituminous coal and lignite in the United States were calculated in accordance with the prevailing conditions of seam thickness and depth of overburden in each of the several coal-producing areas of the Nation. Within defined limits of seam thickness and depth of overburden, it is estimated that there was a remaining strippable resource of 118 billion tons of raw bituminous coal and lignite as of January 1, 1968. Because of topography, natural and manmade features, and other limitations, only 45 billion tons of the resource are strippable reserves. Of this, 32 billion tons is considered low-sulfur (less than 1 percent), 4 billion tons is medium-sulfur (1 to 2 percent), and 9 billion tons is high-sulfur (over 2 percent) coal. Owing to a cleaning loss affecting that portion of strip coal that is mechanically cleaned, the 45 billion tons of strippable reserves are reduced to 39.6 billion tons of marketable coal. A brief discussion is given for each coal-producing State, summarizing past and present production, historical background, and outlook. Appendix A contains reserve data by State, county, seam, and sulfur content. Appendix B contains the general information and requirements necessary to comply with the current strip mining laws covering 20 States.

Jan 1, 1971

By Thomas Jancic

Two of the open-pit, copper-molybdenum mining operations of Duval Corporation are located in the foothills of the Sierrita Mountains approximately 30 miles southwest of Tucson, Arizona. In March 1959, mining from a moderate sized porphyry deposit known as the "Esperanza orebody" was begun at a rate of 10,000 tons of ore per day. Some five years later, a sizeable group of mineral claims west of Esperanza became available to Duval. Earlier exploration and development drilling in this area by others indicated an orebody of greater size but lower tenor than that of Esperanza. A drilling program conducted by Duval not only verified the results of the prior drilling but in addition, revealed a continuation of the mineralization to the south and east. Thus was developed the Sierrita orebody. Open pit design delineated 414 million tons of ore containing an average copper content of 0.35 percent and a molybdenum content of 0.036 percent. In April 1966, the office of Emergency Planning authorized General Services Administration to undertake a program under the Defense Production Act to en¬courage additional domestic production of copper in the interest of national defense. Duval's Sierrita Project was brought to GSA's attention in May 1966 on November 28, 1967, an agreement providing for the development of the Sierrita Property was consummated with GSA. In March 1970, the first copper-molybdenum concentrates were produced in the 72,000 tons-per-day concentrator. Pre-production stripping exceeded the scheduled 105 million tons despite the comparatively short lead time available to equip the mine, build the mine plant facilities, and staff the technical, supervisory, and labor forces. Shortly before the first concentrates were produced, plans were being formulated for a program to increase processing capacity by approximately 15 percent, which entailed increasing overall mining capacity by approximately 50,000 tons per day. This program is scheduled for completion early in 1971.

Jan 1, 1971

This evening I would like to speak about men for the mineral industry.It is trite to say that the mining industry is expanding rapidly and that technically trained men are in short supply. How short is difficult to assess and impossible to quantify.The industry has been traditionally managed by technically trained men experienced in the ways of their fellow men. Let us start with the assumption that men with this training and experience are essential to management of mining and metallurgical enterprises.I suggest that we do this as it avoids argument with those who are beginning to suggest that such men are not so important as they used to be; who are suggesting that the latest sophisticated business management schools can produce managers who can straight out of school join the upper echelons of an organization and successfully manage it by the use of modern systems and techniques without the need to rub shoulders with men of all callings and get their hands dirty in the process.This kind of thinking brings to mind the modern cargo ship which is equipped with all the latest gadgets of science. It can find its way from Sydney to Auckland with no one in the engine room and the man on the bridge spending most of his time writing to his wife or reading the latest novel.How often do we read of this ship being tied up in Sydney because the crew sympathizes with the cook who has been slighted by some uncomplimentary remark about his toheroa soup? Here is a pieceof sophisticated machinery stopped through no technical fault, but held up by the whim of man. The understanding of man by man can spell the success or failure of any endeavour. A single man can leadan organization to the pinnacles of success, or doom it to utter failure in spite of modern systems and techniques.So let us start from the point that people matter.Through the years our Institute has been fortunate in having many members who have felt strongly...

Jan 1, 1970

By R. L. Caldwell, E. E. Glenn, L. J. Norton, A. J. D. Straus, S. V. Holcomb, J. Zemanek

A new and unique logging tool, called the Borehole Televiewer (BHTV), has been developed to inspect boreholes and to evaluate formations. Even though geologists and engineers have had only about 3 years' experience with the BHTV, the thinking of many of them has been radically influenced by the fascinating and revealing "log-picture" recorded with the tool. The BHTV fills a need for a logging tool that can produce a direct and descriptive record of the physical properties of the borehole environment. Although primarily developed to evaluate fractured reservoirs, the BHTV has been used successfully to solve a variety of problems related to formation evaluation and borehole inspection. Geologists and petroleum engineers have been confounded for many years by the problems of locating and evaluating fractures. Interpretation of the usual resistivity, acoustic or radioactivity logs, as well as the analysis of cores, for evaluation of fractured reservoirs is extremely difficult and often not definitive. This is understandable since analysis of cores from fractured formations has reported variously: (a) low porosity, (b) no effective permeability, (c) lack of any matrix oil saturation and (d) oil stains on fracture planes as the only indications of potential production.14 In recent years acoustic amplitude logs have been introduced and used with varying degrees of success to locate fractures.8'9'11"13 Conventional amplitude logs at best give only qualitative answers where quantitative ones are desired. The logs reveal nothing of the orientation of the fractures. In addition to these logs, various types of cameras, television, and rubber impression packers have been used for borehole inspection. (See Appendix.) The BHTV logging tool supplies both the quantitative and the orientation answers about fractures. The borehole can be filled with any homogeneous, gas-free liquid such as fresh water, saturated brine, crude oil or drilling muds. This tool takes an "acoustic picture" of the borehole wall. The resulting log is a representation of the borehole wall as if it were split vertically and laid flat. The log is oriented with respect to magnetic north. Any physical changes in the borehole wall are seen as changes in picture intensity. In this way, fractures, deformation or pits are reflected on the log. Tool Description The fundamental parts of the BHTV are shown in Fig. 1. A piezoelectric transducer probes the borehole wall with bursts of acoustic energy. A flux-gate magnetometer senses the earth's magnetic field and provides the means for determining the orientation of the log. A motor rotates the transducer and mag-

Jan 1, 1970

By L. E. Cardwell

This publication contains routine analyses and related source data for 390 natural gas samples from 22 States and five foreign countries. Of this total, 385 samples were collected during calendar year 1969. The remaining five analyses are of samples collected during previous years, but releases granting permission to publish the results were not received until 1969. All samples were collected as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus which are described in Bureau of Mines Bulletins 4863 and 576.4 Eleven previous publications have presented the results of 8,660 gas analyses made by the Bureau of Mines Helium Activity prior to 1969. The first three, Bulletins 486,6 576,6 and 617,7 contain analyses and related source

Jan 1, 1970

By Harry K. James

Experimental studies of the physical and explosion characteristics of pure hydrazine nitrate and multicomponent systems containing hydrazine nitrate, supplemented with an extensive Literature survey, are presented. Such proper- ties as melting point, heat of fusion, density, viscosity, surface tension, thermal stability, decomposition process, detonation velocity, impact sensitivity, and TNT equivalence are included.

Jan 1, 1970

By Foster Fraas

Under a very high vacuum of 10-8 torr the transfer of terrestrial mineral beneficiation methods to the vacuum ambient of extraterrestrial locations such as the lunar surface was investigated. In the size range for the electro-static and magnetic separation of ores (minus 35 plus 150 mesh) there is no adhesion of particles produced by crushing and grinding due to the limited contact area, and for repeated contacts area size has a frequency of occurrence in accordance to the normal law. The photoelectric effect which is successful in separating a few minerals in an air ambient has a wider application in a vacuum, while the lack of air viscosity and sound transmission provides for high feed velocities and the adaptation of particle vibration to dispersion and grinding. Contact electrification is reversible upon return to atmosphere.

Jan 1, 1970

By M. Metzger, J. C. Bilello

Microyielding in 99.999 pct Cu occuwed in two distinct parabolic microstages and was substantially indeoendent of grain size at the relatiz~ely large grain sizes stzcdied. The strain recouered on unloading was a significant fraction of the forward strain and was initially higher in a copper-coated single crystal than in poly crystals. Results were interpreted in terms of cooperative yielding and short-range dislocation motion activated otter a range of stresses, and a formalism was given for the first microstage. It was suggested that models involving long-range dislocation motion are more appropriate for impure or alloyed fcc metals. THERE are still many unanswered questions concerning the degree and origin of the grain size dependence of plastic properties. In the microstrain region, a theory of the stress-strain curve proposed by Brown and Lukens,' based on an exhaustion hardening model in which the grain boundaries limit the amount of slip per source, accounted for the variation with grain size of microyielding in iron, zinc, and copper.' This theory assumes N dislocation sources per unit volume whose activation stress varies only with grain orientation. Dislocations pile-up against grain boundaries until the back stress deactivates the source, which leads to a relationship between the axial stress and the strain in the microstrain region given by: where G is the shear modulus, D the grain diameter, a the flow stress, and a, is the stress required to activate a source in the most favorably oriented grain.3 If this or other grain-boundary pile-up models are correct, then the reverse strain on unloading would be much larger for a polycrystalline specimen than for a single crystal. Also, the microplasticity would become insensitive to grain size if this could be made larger than the mean dislocation glide path for a single crystal in the microregion. These questions are examined in the present work on polycrys-talline copper and a single crystal coated to provide a synthetic polycrystal. EXPERIMENTAL PROCEDURE Tensile specimens 3 mm sq were prepared from 99.999 pct Cu after a sequence of rolling and vacuum annealing treatments similar to those recommended by Cook and Richards4-6 to minimize preferred orientation. Grain size variation from 0.05 to 0.38 mm was obtained by a final anneal at temperatures from 310" to 700°C. Dislocation etching7 revealed pits on those few grains within 3 deg of (111). For all grain sizes dislocation densities could be estimated as -107 cm per cu cm with no prominent subboundaries. The single crystals, of the same cross section, were grown by the Bridgman technique with axes 8 deg from [Oll] and one face 2 deg from (111). An anneal at 1050°C produced dislocation densities of 2 x 106 cm per cu cm and subboundaries -1 mm apart in these single crystals. A Pb-Sn-Ag creep resistant solder was used to mount the specimens, with a 19 mm effective gage length, into aligned sleeve grips fitted to receive the strain gages. All specimens were chemically polished and rinsed8 to remove surface films just prior to testing. The synthetic polycrystal was made by electroplating a single crystal with 1 µ of polycrystalline copper from a cyanide bath. Mechanical testing was carried out on an Instron machine using two matched LVDT tranducers to measure specimen displacement, the temperature and the measuring circuit being sufficiently stable to yield a strain sensitivity of 5 x 107. At the crosshead speeds employed, plastic strain rates were, above strains of 10¯4, about 10¯5 per sec for polycrystalline specimens and 10-4 per sec for the single crystals. Plastic strain rates were an order of magnitude lower at strains near l0- '. A few checks at strain rates tenfold higher were made for reassurance that the initial yielding of polycrystalline copper was not strongly strain-rate dependent. Test procedures followed the general framework outlined by Roberts and Brown.9,10 An alignment preload of 8 g per sq mm for polycrystals, and 2 to 4 g per sq mm for single crystals, was used for all tests. These gave no detectable permanent strain within the sensitivity of the present experiments; although at these stress levels, small permanent strains are detectable in copper with methods of higher sensitivity.11 12 stress and strain data are reported in terms of axial components. RESULTS General. The initial yielding is shown in the stress vs strain data of Fig. 1. For polycrystals, cycle lc, the loading line bent over gradually without a well-defined proportional limit, and almost all of the plastic prestrain appeared as permanent strain at the end of the cycle. The unloading curve was accurately linear over most of its length with a distinct break indicating the onset of a significant nonelastic reverse strain at the stress o u, indicated by the arrows. The yielding in subsequent cycles, Id and le, had the same general character. The single crystal behavior, shown to a different scale at the right of Fig. 1, was different in that initially the nonlinear reverse strain was unexpectedly much greater than for polycrystals. It should be noted that these soft crystals had a small elastic

Jan 1, 1970

This report summarizes a study conducted by The Service Bureau Corporation for the Bureau of Mines. Evaluations reflected herein are the result of an independent investigation by The Service Bureau Corporation of methane considerations during coal mining. The study is oriented toward a systematic analysis of methane control problems during coal mining. Throughout this study an attempt has been made to ensure considerations consistent with the recently enacted Federal Coal Mine Health and Safety Act of 1969. References to reports by The Bureau of Mines and others are made for the purposes of establishing identification between the evaluations contained in this report and on-going research efforts.

Jan 1, 1970

By Henry M. Harris

The roll forming of oxide powders was studied in a Bureau of Mines investigation to find the conditions and parameters required to make satisfactory ceramic strip. High-quality porous or dense alumina, zirconia, and porcelain shapes were made by sintering strip roll-formed at room temperature from powders containing minor amounts of binder and water. Strips with thicknesses of 0.04 to 0.08 inch and bulk densities from 40 to 90 percent of theoretical densities were made. The parameters most important to formability were particle size, condition of the powders, and roll gap. Other factors affecting quality were speed and surface condition of the rolls, amount and type of binder, water content, and sintering conditions. Ceramic strip was formed at rates up to 78 feet/minute, which is 13 to 23 times faster than reported by previous investigators, and forming was done in a simple and inexpensive roll unit. Reshaping the strip was possible by cutting, grinding, shearing, and stamping. The following innovations were developed that allow roll processing not normally possible with ceramic powders: (1) Fine-sized powders were made into strip by preparing these as partially sintered granules; (2) thick strip was formed by pressure feeding powders into the rolls; (3) flexible strip was made using a rubber-base bonding agent; (4) corrugated strip was formed on shaped rolls; and (5) porcelain strip was densified and reduced in thickness by rerolling while hot.

Jan 1, 1970

By Donald R. Johnson

Apparatus providing simultaneous differential thermal analysis, thermo-gravimetry, and evolved gas analysis, has been developed by the Bureau of Mines specifically for thermal study of oil shale and other solid, natural fuels. The apparatus is described in detail, and simultaneous analyses on a single sample of an oil shale mineral, nahcolite, and a thermal analysis demonstration compound, calcium oxalate monohydrate, are presented to demonstrate the instrument's capabilities.

Jan 1, 1970

By Rollien R. Wells

The Bureau of Mines was created in 1910 by an act of Congress and subsequently directed to: "...conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment, and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources through the prevention of waste ..." Under this broad charter, the Bureau's responsibilities have changed and grown from an almost exclusive concern with coal and coal mine safety to the present emphasis on a full spectrum of mineral producing and consuming problems. In the past 30 years, the domestic consumption of coal, oil, gas, metals, and industrial minerals has more than quadrupled, in parallel with the rapid and enormous growth in industrial production. Of the scores of metals and nonmetals essential to the Nation's progress and security, many are scarce and difficult to wrest from domestic sources. Reserves of some ores are dwindling. Available ore resources are becoming leaner and more difficult to treat. In recognition of this many faceted problem, the Bureau has engaged in a continuing quest for new and improved technology to enable economic exploitation of marginal minerals and fuels, to find substitutes for minerals in short supply, and to create better materials to meet the expanding and diverse requirements of the growing economy. The current central concern of the Bureau is focused on meeting projected fuel, metal, and mineral demands at the lowest real cost by recovery from available resources by new and improved technology that minimizes waste, hazards, and social and environmental problems.

Jan 1, 1970

By J. B. Cohen, O. F. Kimball

Aging of specimens of Au-20 at. pct Ni and Au-40 at. pct Ni has been followed with electron microscopy, resistance, magnetic measurements, and X-ray diffraction. The periodic structures observed by electron microscopy in Au-Ni alloys by Fisher and Embury are shown to be due to nickel-rich prepre-cipitates. Assuming this alloy system undergoes spinodal decomposition, our observations and available data on thermodynamic properties and elastic constants indicate that the gradient energy coefficient in this system is of the order of 10-5 ergs cm-1 . Shifts of X-ray peaks in this system have been found to be due primarily to residual stresses, not faulting. A large effect of applied stress during aging was detected by X-rays and electron microscopy for the Au-20 at. pct Ni alloy. The presence of a preprecipitation stage during aging of gold-rich Au-Ni alloys for short times below 300°C has been indicated by several previous investigations. Changes in electrical resistivity,1"3 elastic modulus,4 superparamagnetisrn,5 positions of X-ray diffraction peaks,6 and hardness7 have been studied. Electron diffraction and microscopic studies by Fukano8 and Fisher and Embury9 respectively showed that the precipitation process resulted in the formation of periodic composition fluctuations—perhaps spinodal decomposition. MOSS10 detected a satellite with X-rays in quenched specimens, but the wavelength was much smallerthan that found by Fukano. Recently Woodilla and Averbac11 detected a modulation similar to that found by Moss, but with electron diffraction. They suggested that the microstructures observed by Fisher and Embury may be simply due to a Moir'e effect from a back deposit of gold during electropolishing. Satellites in electron diffraction can be enhanced by small bends or tilts of a foil. Even if this were not the case, asymmetric satellites, as are found in Au-Ni are difficult to analyze. They are principally influenced by the large differences in atomic size in this system, and obtaining information on the associated composition fluctuations depends on assumptions as to whether or not there are isolated clusters or composition "waves", and in the latter case whether or not the entire specimen has decomposed. Assuming that decomposition was complete in alloys aged at low temperatures, Woodilla and Averbach suggested that the satellites indicated a composition which varied about the average value by only± 5 pct, much less than that predicted from the phase limits, Fig. 1; they attributed this small variation to a cessation of the reaction caused by the loss of mobile vacancies. In Ref. 12 it was shown that vacancies are trapped by the preprecipitate in this system. Furthermore, after reversion, aging proceeds at a much slower rate than immediately after a quench from the solution temperature,5'11,13 indicating the importance of vacancies in the kinetics. In some senses Au-Ni is a favorable system for studying preprecipitation and reversion mechanisms because of the simplicity of the equilibrium diagram14 and the availability of good thermodynamic15 and diffusion data.16,l7 The calculations necessary to relate the decomposition process to classical nucleation and growth or to spinodal decomposition, as well as those necessary for understanding reversion mechanisms, can, therefore, be made. As an example, the position of the chemical spinodal, calculated from the thermo-dynamic data of Sellars and Maak15 with the method described by Rundman and Hilliard,18 is included in Fig. 1. It is compared to the chemical spinodal calculated from the equilibrium miscibility gap by Cook and Hilliard's method.l9 Included is the coherent spinodal suggested by Golding and MOSS," using measured elastic constants for their calculations and the same ther-modynamic data. The spinodal estimated by Woodilla and Averbach,11 by determining the temperature limits for the observation of the satellites discussed above, is also given. Actually this last curve is open to question on the following grounds: As a phase boundary is approached the spacing of particles or the wavelength

Jan 1, 1970

By L. W. Pommier, F. B. Brien, A. K. Bhasin

In the field of mineral processing, although many operations are applied to suspensions of ore particles in fluids, there is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. Previously proposed equations, based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids, are exam ined in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. As more knowledge is acquired in regard to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow predictions of conditions to achieve optimum results for engineering purposes. In the field of minerals processing, many operations are applied to suspensions of ore particles in fluids. The differential movement of solids of various sizes and densities in suspensions is of utmost importance to gravity concentration, wet classification, flotation, hydrometallurgy, and pipeline transport of solids. The subject is also of importance to other branches of engineering; for example, those involved with soil mechanics, ceramic slips, and oil-well drilling fluids. There is a lack of fundamental knowledge relative to the flow resistance encountered by immersed bodies moving through solid-liquid suspensions. The problems encountered in the direct application of the well-known Stokes and Newton's Laws to non-Newtonian systems have been examined in a previous paper.' Equations were proposed based on the Ostwald-de Waele (power-law) model for non-Newtonian fluids. This present paper examines these equations in the turbulent flow region relative to a number of pertinent variables and their effects on the movement of immersed bodies. It is thought that, as more knowledge is acquired as to the effects of suspension variables on the rheological properties, useful relationships may be proposed to allow prediction of conditions to achieve optimum results for engineering purposes. The purpose of this paper is to make an initial assessment of the nature and magnitude of pertinent suspension variables. In order to avoid too voluminous a document, the examination of kinetics and mechanisms will be omitted at this time. THEORY A Newtonian fluid is defined as a fluid in which the stress is proportional to the rate of strain, 2 i.e.: H = viscosity; see Table I. for list of symbols The following equations are conventionally used to assess the motion of spherical particles moving under laminar and turbulent flow conditions through Newtonian fluids: When these relationships are applied in practice to suspensions, the liquid density is substituted by a composite suspension density, and viscosity is usually taken as that of the suspending liquid or an approximated "apparent viscosity." However, suspensions are non-Newtonian in character3 and thus, more than one viscosity parameter is required to describe their behavior. A number of models have been proposed for non-Newtonian fluids;2,4 among these the simplest is the Ostwaldde Waele or power-law model for incompressible fluids which for one dimensional flow may be reduced to:

Jan 1, 1970

By C. M. Romanowitz

This report deals with the factors which should be considered in evaluating a placer deposit and selecting a dredging system for mineral recovery. Overall dredging feasibility and the design of dredging systems are reviewed. Excavation methods, each with its advantages and disadvantages, are compared. Direct operating costs, both original and updated, of gold dredges with bucket capacities of 6 to 18 cubic feet are included. Costs vary with digging depth, changes in environmental conditions, and physical characteristics of the placer, all of which affect excavation rate and recovery. The costs, updated with appropriate indexes, should be used only as guidelines to evaluate potential dredging projects with similar characteristics. The relation of direct dredging costs to annual production is graphically illustrated by a family of curved envelopes that span dredge sizes from 2-112 to 18 cubic feet. A curve fitted to the data expresses the relation of direct costs to annual production for 151 dredge-years.

Jan 1, 1970

The Bureau of Mines analyzed the cycle of secondary gold to determine the quantity of gold not being recovered from scrap, and to identify areas for research to increase the supply of gold from scrap. Secondary gold in 1967 was estimated to be 2.4 million troy ounces; this excludes secondary gold which is recycled within consuming plants. Firms contacted included consumers using about 41 percent of the gold in 1967, And refiners that recovered about 90 percent of the secondary gold. Results of the study indicate that loss of gold is small, and refiners and consumers are accelerating programs designed to reduce recovery costs. With the increasing generation of low-grade industrial scrap, research is needed to improve present recovery techniques and to develop methods to accelerate the flow of secondary gold back to supply.

Jan 1, 1970

By William T. Barrett

It is said that Thales of Miletus, 600 B.C.,1 was aware of the attraction of lodestone toward iron and highly magnetic minerals. However, the birth of magnetic concentration followed shortly after the invention of the first electromagnet by Sturgeon in 1825. Sturgeon's magnet was described in the annals of electricity.2 The first attempts to concentrate minerals by the use of magnets date back to about 18473 but the first commercial drum-concentrator was apparently invented by R. Cook in 1849. Credit must also be given to the invention of P. Righter's machine in 1867,5 and to the highly successful Wenström separator devised in Sweden in 1883.8 Since the advent of these early separators there have been virtually hundreds of patents granted covering minor modifications of drum-type magnetic separators. The more important advances from a technological viewpoint have been the design of stable power supplies for d.c. magnets, the advent of ceramic permanent magnets which are now replacing electromagnets for the concentration of ferromagnetic minerals, and advances in general magnet and machine configurations.7 One of the problems facing both the designer and the user of magnetic separators is the evaluation of the body forces acting on particles in the magnetic field of the separator. Perhaps the most elegant method of evaluating the body force associated with a drum-type magnetic separator is that recently suggested by W. F. Brown.8 Brown measures the radial component of the field intensity one-half inch from the drum surface and fits a Fourier series in the angle about the drum axis (Figure 1). Once the coefficients of the series are known, it is then possible to calculate [ ]

Jan 1, 1970