Search Documents

These proceedings consist of an introduction and four descriptive papers. The first paper is an update on fire protection for large haulage vehicles, the second paper is concerned with improved visibility systems for large haul- age vehicles, the third paper is on improved ladders for large haulage vehicles, and the fourth paper is concerned with large haul-age vehicle operator training systems.

Jan 1, 1980

By T. T. Chen, W. Petruk

The mineralogy of the feed, concentrates and tailings from the Heath Steele mill in New Brunswick was studied in detail to determine the liberation and recoveries of the major ore minerals, and to characterize the occurrence and distribution of the trace elements. The ore milled during August 1977 contained an average of 4.34 wt % Zn, 1.25 wt % Cu, 1.64 wt % Pb and 90 gr/ton Ag. The main trace elements in the ore are silver, cadmium, indium, cobalt, antimony, bismuth, arsenic, mercury, tin and gold. Silver is carried in solid solution in tetrahedrite-tennantlte, galena, Ag-Sb sulfosalts and Pb-Bi-Sb sulfosalts. Approximately half of the silver is recovered in the lead and copper concentrates and the remainder is lost in the tailings and Zn concentrate. As the major silver-bearing minerals also contain Sb and Bi, recovering silver by ore dressing would involve recovering elements that are troublesome in extraction metallurgy. Cadmium and most of the indium and mercury occur in solid solution in sphalerite and consequently are recovered in the zinc concentrate. Some indium is also recovered in the copper concentrate in a second unidentified indium-bearing mineral. Cobalt and arsenic occur principally in arsenopyrite, cobaltite, a Co-Fe sulfarsenide, pyrite and pyrrhotite, and follow these minerals into the tailings. Recovery of the valuable element cobalt, therefore, would involve recovering the environmentally hazardous element arsenic. Most of the tin and gold report to tailings. The ore was ground to about 80% minus 270 mesh. At this grind, 71 wt % of the sphalerite, 66 wt % of the chalcopyrite and 59 wt % of the galena were liberated. Recoveries of free sphalerite, free chalcopyrite and free galena in the Zn, Cu and Pb concentrates were 85 wt %, 76 wt % and 80 wt %, respectively; recoveries of unliberated sphalerite, unliberated chalcopyrite and unliberated galena in the respective Zn, Cu and Pb concentrates were 48 wt %, 5 wt % and 7 wt %. Some of the unliberated sphalerite and chalcopyrite grains in the tailings are large and would have been liberated at a finer grind.

Jan 1, 1980

By Rudolph K. Hoagberg

Silica sands, primarily in coarse size ranges, are used to prop open fissures or voids created in the bedrock by hydraulic fracturing. This procedure increases the flow of gas or oil or other fluids through the bedrock. The sands used must meet various specifications relating to their physical and chemical characteristics; these characteristics are in turn related to the geologic provenance of the sand deposit. The Jordan Sandstone, a Cambrian formation which is exposed in Minnesota and Wisconsin, meets the specifications of a proppant sand by virtue of its depositional history and its sedimentary properties.

Jan 1, 1980

By M. F. Bucek

This report summarizes the activities performed and the results achieved during a two-phased investigation of the technical and economic feasibility of disposing of coal mine refuse underground in active mines, Three coal regions in the United States that are most severely affected by coal refuse disposal problems are identified: southwestern Pennsylvania, southern West Virginia, southwestern West Virginia and eastern Kentucky. For each region, a conceptual mine model is presented that describes the geologic conditions, mining methods, and environmental circumstances typical of that region. The model mine that was prepared for the Kanawha Region in Southwestern West Virginia and eastern Kentucky was selected as the basis for developing alternative conceptual designs of underground disposal systems in the second phase of this investigation. Procedures used in selecting the regions and in modeling typical mines are described in Part I of the report. Part II of the report describes existing methods for stowing refuse underground, presents three alternative conceptual designs of stowing system that would be appropriate for the model mine postulated in the first phase of the study, discusses technical characteristics and environmental effects relative to the various systems, and evaluates the technical and economic feasibility of the three alternative disposal system designs. Comparisons costs among systems and with costs or surface disposal are presented.

Jan 1, 1980

By Fred Leonard

This report is principally concerned with the engineering and economic feasibility of area surface coal mining systems other than draglines. This analysis evaluates shovel/ trucks, shovel/crusher/conveyors, and shovel/rail excavation and haulage systems for an assortment of geologic environments and production rates in the Powder River Basin (PRB). Shovel/trucks, front-end loaders trucks, and shovel/crusher/conveyors were studied in a multi-seam, dipping geologic area of the Four Corners Region. The Texas lignite engineering and economic research involved bucket-wheel excavators (BWE), BWE/backhoes, and scraper/backhoe combinations for overburden and coal excavation. The PRB truck/shovel study utilized the most recent computer simulation available in both the design and cost analyses. Detailed engineering analysis, followed by in-depth operating costs (operating and depreciation), result in a complete evaluation of each mining system. Cost comparisons of the different mining systems under similar geologic and production constraints are presented in the report to illustrate the estimated capital investment and production costs per ton of coal and bank cubic yard of overburden.

Jan 1, 1980

By Kenneth C. Ko

An engineering investigation was carried out on the technical and economic feasibility of implementing flexible liner/backpacking support systems In an advancing tailgate longwall mine. The system for a model mine consists of a circular tube constructed of liner plates and flyash backpacking. Flyash is pneumatically stowed into the tailgate. Small amounts of cement may be mixed to improve the support capability of the fill In difficult local ground conditions. Water is added inside the nozzle immediately prior to spraying. Results of theoretical analyses and a field test show that the designed system is technically feasible, can be cost-competitive, provides more stable ground conditions, and can Increase productivity and coal recovery, when compared with existing retreat longwall systems. In certain mine layouts, the new system can reduce the direct mining costs by a significant amount. The system would be particularly applicable to deeper coal beds with bad ground conditions.

Jan 1, 1980

The Bureau of Mines is responsible for a broad spectrum of programs for meeting the diverse and changing mineral resource needs of the Nation. These programs are managed by the Director and two Deputy Directors, who formulate general policy and program direction from the Washington, D.C., headquarters. A senior advisory staff, consisting of the Chief Staff Officer, Chief Scientist, and Chief Mining Engineer, provides advice and consultation to the Director on a wide range of scientific and technical matters and acts on behalf of the Director to maintain liaisons with other government agencies, mineral industries, and professional societies. Bureau program activities are classified into two major functions: (1) Developing new and improved technology that will make the production and processing of minerals more efficient, safer and more healthful for mineral workers and the public, and more compatible with a quality environment.

Jan 1, 1980

By G. J. Colaizzi

The Bureau of Mines, at the request of local authorities in Rock Springs, Wyo., investigated and conducted through contracts a multistage program of exploratory drilling and pumped-slurry backfilling of 15 areas of potential subsidence in abandoned mine workings underneath that community. Initially, the Bureau in 1969 had recommended a program of gravity blind flushing of some of the inaccessible mine voids, and in 1970 a new technique, the pumped-slurry injection process, was tested for the first time in a site adjacent to the city's area of severe surface subsidence. Success of this initial testing program, and of a large-scale project in Scranton, Pa., led to further large- scale projects, funded by Congress, that resulted in the successful back- filling not only of all 15 target areas of potential subsidence in Rock Springs, but also of several areas in other States. Total cost of the projects in Rock Springs, including the original pumped-slurry test, was $3,243,993. A total of about 923,000 tons of sand was injected hydraulically into mine voids, rendering 178 acres of residential and central-downtown areas of Rock Springs less susceptible to subsidence damage. The pumped-slurry method was proved to be much superior to the gravity blind flushing method in term of the amount of solids that could be injected underground through a single borehole. However, there are special conditions that make this technique more or less applicable in different areas or underground configurations, as noted in the report's conclusions.

Jan 1, 1980

By Frank C. Townsend

Centrifugal model embankments with varying geometries and materials were constructed of- coal waste material, accelerated From 100 to 120 times earth's gravity, and subjected to various throughflow rates until failure occurred. Complementary laboratory tests were performed on the waste materials to obtain strength and permeability parameters for analytical calculations to predict observed centrifugal model behavior. Failures in the form of deep.-seated failure, or erosion and sediment transport or a combination of both, occurred in model embankments with 1V:1-1/2H and 1V:2H slopes when the phreatic surface due to seepage exited on the downstream slope: Positive seepage control, i.e., a toe drain successfully prevented sloughing and failures. Slope stability analyses agreed well, albeit conservatively, with observed model performance. Factors of safety ranged from 0.7 to 1.02 at the instant of failure for models with retrogressing slips as compared with 1.05 to 1.7 for stable embankments, These models verified existing criteria of a minimum safety factor of 1 3 and the necessity of positive seepage control.

Jan 1, 1980

By Zsuzsanna Zborovszky

[Certain chapters of the tentative document entitled, "Test Requirements for instruments & Apparatus to be Considered for MESA Intrinsically Safe Certification" are evaluated and supporting data are presented on certain key issues with the purpose of helping the regulatory agency in improving the above document. The subjects discussed in detail are: hot wire ignition with W and BeCu wires; the most sensitive methane-air :and propane air ratio; the ignition limits for inductive-resistive circuits in 8.3°; methane-air mixtures in the 24-OV, 100 mH-2 [ ]H range, the resistive ignition limit as a special case when L ? 0; the capacitive-resistive ignition limit representing a four ,dimensional problem is analyzed and discussed in general and the variation of the ignition limit using Vo and/or r2 as a parameter are determined experimentally. The ignition limit is also determined for the [r1 ,~ r2] = 0 case ("capacitor alone") and for the most dangerous capacitive resistive circuit combination. The ignition limits are below the limits proposed in the document. A survey of the different factors influencing the ignition is made as to their suitability to provide a constant safety factor. It is shown that a constant safety factor cannot be achieved. The best method for applying a safety factor appears to be the increase of initial pressure or use of other gas mixture. The revision of the safety factor concept and ignition limit curves is recommended.]

Jan 1, 1980

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state requlatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

This: symposium was sponsored by the Bureau of Mines, U.S. Department of the lnterior, in order to critically examine the state-of-the-art of sulfide flotation chemistry and to define current and emerging problems that should be emphasized in future fundamental research. The topics covered through invited papers include both reviews and recent research results in the areas of thermodynamics of reagent-mineral interactions; collector adsorption processes; the effects of solid-state point defects on flotation; activation and deactivation phenomena; the electrochemical role of oxygen in sulfide flotation; environmental problems in flotation; and selective flocculation of fines. Papers riving perspectives on flotation research in relationship to our national mineral requirements and the relationships between industrial flotation research and academics are also presented. An edited summary of the symposium follows the papers.

Jan 1, 1980

By Virgil Marple

In the summer of 1979 the University of Minnesota Mobile Laboratory (UMML), designed for the analysis of airborne particles and gases was used to study fugitive dust from an open pit coal mine. The analysis consisted of determining the particle size distribution and concentration of dust from various mining operations, such as blasting, draglines, loading, roadways and bottom scrapers. For some operations the particles size distribution and concentrations were determined at varying distrances. Details of the dust concentration within the plumes as the plume passed the UMML were measured with an optical particle counter. For line sources, such as roadways this enabled the calculation of the particle flux at the sampling location. In addition to the standard instruments associated with the UMML, the applicability of some new instruments were investigated. These included a uniform deposit cascade impactor and a flux meter. Finally, a technique in identifying plume origins which utilized elemental X-ray flourescence analysis of filter samples was shown to be effective.

Jan 1, 1980

This Bureau of Mines report reviews the information presented at the Sixth Mineral Waste Utilization Symposium cosponsored by the Bureau of Mines, U.S. Department of the Interior, and the IIT Research Institute. Environmental scientists and engineers from nine countries participated in the symposium, which was held May 2-3, 1978, at the Chicago campus of IIT Research Institute. The 56 papers presented on the reclamation and recycling of mining and mineral wastes, municipal solid waste, industrial wastes, and scrap metal are summarized herein.

Jan 1, 1980

By Wils L. Cooley

The report covers several aspects of mine safety ground systems, primarily for underground coal mines. The design of a combined ground fault-ground check monitoring system is presented. An analysis is made of grounding systems for dc shuttle cars. Complete resistance data and results of physical inspections of self-salting ground rods are presented. A detailed resistance and economic analysis is presented for the use of composite materials for building inexpensive and effective ground beds in high-resistivity areas. The desireability of penetrating the coal seam with a borehole safety ground is investigated. A report is made of a Mine Substation Grounding and Bonding Workshop.

Jan 1, 1980

By David Bendersky

This report covers a technical and economic investigation of old electrical power systems, equipment and practices being used in the metal/non-metal raining industry. The principal sources of information were the MSHA District offices, visits to representa¬tive mines and mills, equipment manufacturers and the literature. A list of 85 mines and mills, submitted by the MSHA Districts as candidates for this study, is given and their characteristics are analysed. The electrical power systems and practices at the 10 mines and 9 mills which were visited are described. The principal areas which do not conform to standard electrical practices are discussed with emphasis on the safety aspects of these practices. The costs to update electrical power systems and practices in metal/non-metal mines and mills are given. The principal findings of the study are summarized and recommendations are submitted.

Jan 1, 1980

By Carl Fisher

A microseismic roof fall warning system was field tested in Western and Eastern coal mines in the United States to better define the capabilities and limitations of the microseismic method in predicting roof fall Microseismic event and energy type data were obtained and documented for twenty-three coal mine roof falls. Field test results indicate that both the microseismic event and energy methods, as applied in this development effort, have a high probability for successful application in a commercially practical roof fall warning system. Based on the results and experience obtained during field testing, a commercial prototype microseismic roof fall warning system was designed and constructed. Although it was the intent of the program to field test the commercial prototype system, delays in equipment fabrication and contract time limitations did not permit field testing.

Jan 1, 1980

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state regulatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

By F. A. Penning

An experimental and analytical investigation was conducted on a recoverable pit bottom buffer. Work was conducted at the Colorado School of Mines using the U.S. Bureau of Mine-s free fall test tower. The four-sided butter, one of several designs by Cable Belt Ltd., was constructed of reinforced rubber slabs. The kinetic energy of falling weights, 1670 to 6000 lb, was absorbed by the flexure of rubber slabs loaded along their edge. A series of constant energy, 3000 ft-lb and maximum design velocity, 600 fpm tests were conducted. Static testing of the buffer established the load-deformation behavior. A large hysteresis loop plotted above and below the data published by the manufacturer. Creep was evident during; the loading Lend unloading cycle. Electronic instrumentation measured deceleration using your accelerometers; overall and intermediate movement was found from four displacement transducers; bending strains were recorded at four locations; and base reactions were measured by using four load cells. Data were recorded on tape and played back on a recording oscillograph. High speed movies were taken of all the tests. Symmetry of response and rebounds, when they occurred, were noted. From the displacement-time and load-time data, maximum decelerations were calculated by four methods and different assumptions. Good agreement was found from these approaches. Impact loads ranged from a low of 0.7 to a high of 6.1 gs. A dynamic computer model was written for the response of the buffer. Displacement-time, and acceleration-time plots show close correspondence with experimental data for the ten experiments. Data from accelerometers, displacement transducers, strain gages, and load cells are included. The computer program listing, and displacement-time acceleration-time plots are also presented.

Jan 1, 1980

By D. E. Andrews

The objective of this study was to investigate the environmental effects of slaking of surface mine spoils. To accomplish this, both field and laboratory programs were undertaken, supplemented by a thorough literature search. The field program consisted of drilling the highwall as well as test pitting in recent, two-, five, and ten- year-old spoil piles at four active mining sites in the eastern bituminous coal fields. Pertinent observations were made and samples collected for laboratory analyses which consisted of several standard geotechnical, agronomic, and geochemical tests. Durability tests utilized included jar slake, cyclic wet-dry, rate of slake, and slake durability tests. Correlation between field and laboratory portions was made- and results presented. The report is concluded with a discussion of the slaking process and associated environmental impacts, proposal of a preliminary classification system for use in premine planning, and presentation of management techniques to optimize the slaking process.

Jan 1, 1980