Search Documents

By Ron J. Elliott, Dylan Wedgewood

A series of five signature holes were blasted at the Highvale Mine and the resultant seismic data was analyzed to make recommendations on how best to address neighbour complaints regarding blast vibrations. From an analysis of peak vibration levels measured at the closest neighbour for blasting during 2016, it was determined that the blast vibration intensity varied between 1.4 to 4.3 mm/sec (0.06-0.17 ins./sec.), well below the level of concern for the onset of minor damage to residential structures, however, the frequency of the blast vibrations was between 2.2 and 9.7 Hz, which is within the range of the natural resonant frequency for a single story home. This was determined to be the cause of the neighbour complaints, as the home would be responding to the blast vibrations.

Jan 1, 2018

By D. J. Coolidge, H. L. Sheakley

THIS paper does not deal with all sands used in the glass industry in Missouri; it covers only that used in the plate-glass factory at Crystal City. However, it is probably safe to say that other sands, produced throughout the state for this purpose, are of identical nature. The glass sand used in Missouri is commonly called the St. Peter deposit, which is ascribed to the Ordovician Rock series in the form of sandstone. This St. Peter deposit, aside from a few small outliers, covers a large area of eastern Missouri. It forms, through a broad curve, the northeast margin of the typical Ozark region between Cape Girardeau on the southeast and Mineola, Montgomery County, on the northwest. The belt is extremely irregular, varying from one to ten miles in width; its length is 150 miles in a straight line. The outcrop near the entrance to the Crystal City mine appears in the form of a sandstone bluff approximately 30 ft. high, running along Plattin Creek (Fig. 1). Above the sand rock an overburden of Joachim limestone appears, which thickens to nearly 300 ft. and forms the hill commonly called Buck Knob. Test holes where drilled at various points and the drillers' log indicate that the St. Peter deposit ranges in thickness from 63 to 71 feet. PROPERTIES OF THE ST. PETER SAND From an analysis of the glass sands of the St. Peter formation in Missouri, the follow-

Jan 1, 1942

By O. E. Brown

The measurement principle of the Coulter Counter for particle size analyses is described. The application of the Coulter Counter to cement particle content and size analysis and to the size distribution of clinker from standard grindability tests are described. Methods of calibration, sample preparation and data reduction are presented. The results of the analyses obtained are compared with characteristics associated with performance showing both concordance and non-concordance of test data., Future uses of the Coulter Counter for particle size analysis in research and plant control adaptations are indicated.

Jan 1, 1960

By William G. Pariseau, Mark K. Larson, Douglas R. Tesarik, Heather E. Lawson

"This contribution describes development and application of a user-friendly finite element program, UT3PC, to address three important problems in underground coal mine design: (1) safety of main entries, (2) barrier pillar size needed for entry protection, and (3) safety of bleeder entries during the advance of an adjacent longwall panel. While the finite element method is by far the most popular engineering design tool of the digital age, widespread use by the mining community has been impeded by the relatively high cost of and the need for lengthy specialized training in numerical methods. Implementation of UT3PC overcomes these impediments in three easy steps: First, a material properties file is prepared for the considered site. Next, mesh generation is automatic through an interactive process. A third and last step is simply execution of the program. Examples using data from several western coal mines illustrate the ease of using the application for analysis of main entries, barrier pillars, and bleeder entry safety.INTRODUCTIONRational design of safe underground entries and crosscuts, barrier pillars, and bleeder entries begins with a site-specific analysis of stress. An analysis of stress identifies the critical regions of high-stress concentration where yielding is likely and additional or more focused ground control measures are needed. This analysis also identifies regions where stress concentration is low, and risk mitigation is less urgent. Displacements induced by mining, including roof sag, floor heave, and pillar squeeze, are also of importance to stability. The popular finite element method is well-suited for such analysis and has been in use for studying coal mine engineering problems since the late 1960s (Dahl, 1969). The method has been taught in undergraduate engineering curricula for many years and offers an alternative to existing design procedures based mostly on rules of thumb, empirical methods based on mine data, and predigital-age concepts of strata mechanics. However, despite the versatility of the finite element method, usage has been limited, mainly because of the cost of the software and the required training in numerical methods.The program UT3PC (Pariseau, 2017) has evolved from early two-dimensional versions in the era of mainframe computers. These early versions were still quite limited using only a few hundred elements that required overnight turnaround times. Recent versions of UT3PC are convenient and efficient desktop programs that use several million elements. With the advent of personal computers in the mid-1980s and subsequent increase in computer speed, expanded memory, and lower costs, applications for mining increased in three-way cooperative projects among industry, the former U.S. Bureau of Mines, and academia. The Spokane Research Center of the U.S. Bureau of Mines, in cooperation with the University of Utah, developed a two-dimensional desktop finite element program, UT2PC, available to the mining community in 1991. This was a short course offered at the 1991 SME Annual Meeting in Denver, CO."

Jan 1, 2017

By G. H. Glos

There was a time when an occasional failure of a tailings embankment was considered an acceptable risk associated with mining activities. This is not the case anymore. A major tailings failure today could result in the indictment of mine officials, huge fines and a possible site closure due to the loss of operating permits. As a result of this changed operational environment, tailings disposal facilities must be operated with these potential consequences in mind. Physical controls for tailings embankments are prohibitively expensive. However, the nuclear industry has developed a system of administrative controls as an alternative to physical controls. Administrative controls may be defined as control of actions, through organizations and management, using written procedures, record keeping, review and audit to assure operation of a facility in a safe manner (10 CFR 50). Administrative controls can reduce the cost of operating tailings impoundments, as well as increase the level of confidence in these facilities.

Jan 1, 1999

By Ava Segal, Doga Cagdas Demirkan, Abhidipta Mallik, Sebnem Duzgun, Andrew J. Petruska

Search and rescue operations in mining heavily rely on humans. In the context of emergency situations within underground tunnels, the potential to utilize sensory technology for navigation assistance holds the promise of saving human lives. Our research introduces a device configuration designed to enhance the performance of search and rescue teams. This setup integrates LIDAR and thermal cameras with the Microsoft Hololens, facilitated by the NUC computer and ROS Bridge. Performance assessment involves quantifying the extent to which a user is willing to venture into a light-deprived section of the mine prior to necessitating supplementary illumination. The preliminary outcomes highlight the significant potential of augmented reality assistance in offering indispensable aid to first responders, thereby greatly augmenting the efficiency of search and rescue missions conducted during critical circumstances.

Feb 1, 2024

By Yunxing Cao, Xinsheng Zhang, Bingbing Meng, Shuaifang Guo, Li Wang, Junsheng Zhang

During the initial process of mining a longwall working face, it is often found that the roof will not collapse readily, which increases the risk of later roof collapse disasters. Explosive and hydraulic fracturing are common roof weakening techniques; however, they have certain limitations. In the present study, CO2 fracturing was used for roof weakening during the initial mining phase in the Changcun coal mine, China, which is a novel strategy. First, by analyzing the lithological characteristics of the working face and applying combined beam theory, the breaking spans of the top coal, immediate roof, and main roof were determined before weakening. An F-35 CO2 fracturing device with a rated pressure of 270 MPa was used, which provides fracturing energy equivalent to 0.968 kg of TNT. The fracture radius of the main roof was studied by ANSYS/ LS-DYNA combined with the hanging roof-breaking theory to determine the optimal layout of CO2 fracturing drills. The results show that the breaking spans of the top coal, immediate roof, and main roof were reduced by 3.99 m, 7.66 m, and 22.03 m, respectively. The main roof collapsed as the working face advanced, eliminating the chance of later roof collapse disasters. Compared with hydraulic fracturing and explosives, CO2 fracturing is safer and more practical, giving it significant application potential.

Nov 23, 2023

Antamina is the largest skarn in the world with a resource of ~2,968 Mt averaging 0.89% Cu, 0.77% Zn, 11 g/t Ag and 0.02% Mo (Glencore, 2015). The Antamina skarn surrounds an intrusive complex consisting of 4 porphyry centers comprised of at least 10 phases emplaced between 10.96 ± 0.03 Ma and 10.23 ± 0.07 Ma (U-Pb zircon; this study). Major phases in each porphyry center include: P1 (early), P2 (inter-mineral), and P3 (late). P1 is related to skarn formation; P2 and P3 cross-cut skarns and do not contain skarn alteration. Re-Os molybdenite ages reveal an early mineralization stage in skarns (10.58 ± 0.07 Ma to 10.39 ± 0.05 Ma) and a late stage in P2 and P3 (10.05 ± 0.06 Ma to 9.68 ± 0.05 Ma). Zircon and molybdenite ages generally decrease from NE to SW along the axis of the deposit, and record ~1.5 Ma of magmatic-hydrothermal activity

May 1, 2008

By N Haque

Base metal ores contain low levels of toxic/hazardous elements such as arsenic, antimony, bismuth, cadmium, lead and mercury. Given the large tonnage of base metal ores mined and processed each year globally, the accumulated mass of minor elements introduced into the biosphere is large and could be expected to have a significant environmental impact. Life cycle analysis (LCA) is a methodology that has been developed to assess the environmental impacts of material supply chains over their entire life cycle. Assessing the toxicity impacts of metallic wastes and incorporating these impacts into LCA methodology is not a simple task given the complexity of the issue. However, research and methodology development is in progress internationally to address this. Despite limitations concerning the lack of a coherent framework for characterising the toxicity impacts of metals, including issues such as bioavailability, a study was carried out to give first estimates of the relative toxicity impacts of various waste streams from metal production processes. The wastes considered were: red mud; sulfide tailings (copper, nickel, lead/zinc); lead/zinc slags; synthetic rutile residue; iron oxide residue; and copper slags and anode slimes. These toxicity estimates can be considered the æworst caseÆ scenario for these wastes, where all the metals present are bioavailable. Combining estimates of the amounts of the various waste streams produced in Australia each year with the toxicity results showed that despite their relatively low human toxicity impact per unit mass compared to some other waste streams, red mud and the various sulphide tailings had the highest annual human toxicity load on the environment, along with copper smelting slag and dust. Data from the pH dependent leaching test reported in the literature were assumed to represent first approximations of metal bioavailability and used to compare the two approaches to estimating the toxicity impacts of red mud.

Jan 1, 2009

By J. K. Hrica, T. J. Orr, J. Navoyski, B. Macdonald, C. L. Hoebbel, J. L. Bellanca, B. Demich

Haul truck fatal accidents and injuries continue to be a significant concern for the mining industry. However, the availability of high-quality training materials continues to be limited. Near-miss incident accounts, if packaged well, could help fill this gap, because for every fatality, there are hundreds of reportable accidents and thousands of undocumented near misses. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected detailed accounts of 21 near-miss incidents in virtual interviews with mineworkers at surface mining operations across the country. From these interviews, researchers created four simulation videos. The videos bring these events to life through first-person retelling and various visual perspectives of actual events. Each video exemplifies a critical safety message and a common haul truck hazard. This paper describes the process of taking narratives and turning them into impactful visual stories. NIOSH plans to co-release these simulation videos with the Mine Safety and Health Administration (MSHA) to the mining industry to raise awareness and ultimately help reduce haul truck-related accidents and fatalities in mining.

Feb 1, 2023

By Brendan Demich, Brendan Macdonald, Timothy J. Orr, Jonathan K. Hrica, CASSANDRA L. HOEBBEL, Jason Navoyski, Jennica L. Bellanca

Haul truck fatal accidents and injuries continue to be a significant concern for the mining industry. However, the availability of high-quality training materials continues to be limited. Near-miss incident accounts, if packaged well, could help fill this gap, because for every fatality, there are hundreds of reportable accidents and thousands of undocumented near misses. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected detailed accounts of 21 near-miss incidents in virtual interviews with mineworkers at surface mining operations across the country. From these interviews, researchers created four simulation videos using the Unity game engine. The simulation videos bring these events to life through first-person retelling and various visual perspectives of actual events. Each video exemplifies a critical safety message and a common haul truck hazard. This paper describes the process of taking narratives and turning them into impactful visual stories using graphic simulation. NIOSH plans to co-release these simulation videos with the Mine Safety and Health Administration (MSHA) to the mining industry to raise awareness and ultimately help reduce haul truck-related accidents and fatalities in mining.

Jun 1, 2023

By Luis Valentim, John E. Wiegand

Highwall or face profiling has long been used to facilitate the design and placement of front row blastholes to ensure optimum burdens. Traditionally, a large number of laser measurement points obtained from the rock face or highwall, were input in profiling software packages. This method can be time consuming and requires access to the rock face with a complete view of the highwall, to be successful. Stereo photography has also been used to generate the rock face surface, but this method also requires access to the highwall (and pit floor in some instances) for measurement of reference targets or points.

Jan 1, 2016

By P. J. K Leeuw, E. Uludag, M. J. Nong

Efficient drill-and-blast performance is pivotal to the profitability of deep-level mines, where high operating costs and declining grades demand maximum throughput. This study investigated persistent fragmentation problems at a longhole stoping operation that suffered from simultaneous oversized rock blockages in 300 mm × 300 mm grizzlies and excessive fines. Fifty-one muckpile images from five blasted stopes were analysed with Split-Desktop. Although the overall F₈₀ was 287 mm, nominally suitable for the grizzly aperture, the Rosin- Rammler uniformity index of 0.80 revealed a highly inconsistent size distribution containing both boulders and fines. Existing drill patterns were then evaluated with the Aegis underground software, which showed negligible crack overlap at the toe owing to inadequate spacing and burden. Insufficient energy overlap between blastholes, particularly at the toe, was found to contribute to the coarse fragmentation, while excessive fines were attributed to the crushing and severely fractured zones of blastholes. Optimisation simulations demonstrated that an 89 mm blasthole diameter on a 2 m × 2 m pattern would overlap, aligning with Aegis requirements of balancing powder factor, break angle, and energy distribution. Implementing this revised pattern is expected to reduce secondary breaking, prevent ore-pass blockages, lower fines, and ultimately improve overall production efficiency. The methodology illustrates how integrated image analysis and modelling software can effectively diagnose and address fragmentation issues, particularly in underground longhole mining, where challenging blasting conditions require a balance between achieving optimal fragmentation and maintaining stope stability. This approach offers a cost-effective pathway to improving comminution performance in deeplevel mines.

Oct 2, 2025

By Bo Hyun Kim, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health have tested the finite element code, UT3PC, with LaModel to evaluate their results using know case studies. The purpose of the testing was to demonstrate the usefulness and limitations of these programs in evaluating mine layout design. Both of these software packages are simple to use and free for public download. Their use by mine engineers, along with other tools, such as empirical methods, can enhance the assessment of a mine layout design. LaModel can model mining layout on a mine scale or, at least, on a multiple-panel scale. However, this software has limitations in calibrating to conditions at many coal mines in the western United States. The UT3PC software models smaller parts of a mine and is used to evaluate the design of pillars, shafts, or drifts; but the software calculates all components of the stress tensor and provides stresses, displacements, and safety factors throughout the model volume. The two codes are used to evaluate design of one known case, and UT3PC is used to evaluate another case. The results and approaches demonstrated in the testing are intended to aid mine engineers in evaluating site-specific problems and to show that these tools can provide useful information to the mine engineer in evaluating mine layout design.

Jul 1, 2023

By Hugh McMillan

To protect the water supply for the Metropolitan Chicago area, the Illinois legislature, in 1889, created the Metropolitan Sanitary District of Greater Chicago. To insure the quality of the water supply, the Sanitary District collected and diverted the wastes of 750,000 people away from Lake Michigan. Today, the Sanitary District collects and treats the wastes from a domestic population of 5 ¼ million people and an industrial waste load equivalent to 4 ¼ million people. The District serves Chicago and 120 other cities and suburbs in an 858 square mile area. An average of 1300 million gallons of wastewater is treated each day, producing as a by- product about 700 dry tons of solids which contains more than $10,000 worth of plant nutrients when equated to the value of commercial fertilizer purchased in the retail market. The Sanitary District considered several alternatives to past methods for disposing of these solids, and chose land application as a technique to utilize the solids produced by the wastewater treatment process in a beneficial manner.

Jan 1, 1973

By J. E. Tobey

BECAUSE of the wide-spread publicity given to Nylon yarn as being made from ?coal, air, and water,? the general public has become conscious of the nonfuel uses of bituminous coal. Some of these uses are as filler for fertilizer, carbon for the absorption of orders, for water supply, and for the bedding of cattle. Spectacular as are these accomplishments the fact is that only a small amount of coal is used for nonfuel purposes. It is on the utilization of coal as fuel that the industry depends. Practically all the coal mines for years to come will be used for making coke for the generation of heat. Recently much attention has been paid to the significance of ash in coal. Another study worthy the interest of metallurgists in the iron and steel industries if that of Dr, Lowry of the Carnegie Institute of Technology relative to the percentage of sulphur in coal and coke.

Jan 1, 1941

By Hsin H. Huang

Equilibrium calculational software programs can be effectively utilized to model the importance of activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation on extraction and recovery processes. Illustrative examples using the calculational program ST ABCAL for the creation of diagrams such as EwpH, activity or concentration-pH, and activity or concentration-EH are presented to demonstrate the fundamental characteristics of real hydrometallurgical mercury dissolution and recovery processes. An industrial application will include leaching of mercury from K 106 mercury sulfide waste and solution purification by iron cementation.

Jan 1, 2003

By G. G. Oberfell

THOUGH the largest volume use of natural gas has been, is. and in all probability will continue to be as a fuel for domestic and industrial heating, it has various market outlets, both as a fuel and as a raw material for the chemical industry. Natural gas is a preferred type of fuel where ease of control, fuel uniformity, and freedom from ash are of primary importance. Other industrially important uses are as a source of carbon black and as a fuel in various low-cost heating operations. Many other uses are of varying importance and new potential uses are continually being uncovered, some being of economic importance to the gas indus¬try as a whole, but most of them involve such small volumes of gas that they are only of passing interest. Since various products extracted from natural gas and recovered as by-products from petroleum refining, such as liquefied petroleum gas and fuel oil, are being utilized in many industrial and domestic heating applications, some consideration will have to be given such materials in order to present a reasonably complete story of the importance of natural gas. Some of these materials may prove to be transient competitors and will not be available when more profitable uses are found for them. Meanwhile, however, the potential volumes of such materials available, the current volumes being marketed, and the nature of the utilization are considered as constituting an essential part of the over-all fuel picture.

Jan 1, 1946

By J. A. Every-Brown

Case studies are presented of three derelict sites in Kent and Essex that provide a good cross-section of opportunities for second-generation commercial uses of former chalk, limestone, clay and gravel workings. A 240 ha abandoned chalk quarry at Grays in Essex, now known as Chafford Hundred, is undergoing mixed development to include leisure facilities, a range of housing and commercial areas and an enhanced environment. The 120 ha of Stone Marshes now comprises the Crossways business park and the Dartford international ferry terminal. Reclamation and servicing required more work than had been anticipated and the fact that the area was within the green belt added to the delays, but Blue Circle was eventually able to provide a comprehensive development of the entire area to a high environmental standard. Stone Pit 1 landfill, at Dartford in Kent, is a former chalk quarry 40 ha in area and with an original average depth of 35 m. Landfilling commenced in 1976 and during the period 1979-1984 the site operator designed, developed and installed a gas collection and flaring system. From 1986 a gas plant supplied up to 5 000 000 therm/yr of landfill gas to a local cement works and in 1989 a 1 MW power generation scheme, later expanded to 3 MW, was commissioned. Gas is currently also supplied to a metal refining company for use in internal combustion engines

Aug 1, 1994

By James McGough, Lawrence Mirabelli, Ran Tamir

The paper will demonstrate how automated fragmentation photo analysis is being used at the Lafarge North America, Ravena NY quarry as part of an ongoing drill, blast and primary crushing continuous improvement process. Using on-line fragmentation photo analysis systems at both the primary crusher feed point and crusher discharge belt, data is collected to: benchmark the drill/blast process; monitor the work being done by the primary crusher; measure gradation changes in the crusher feed resulting from changes in drill/blast and measure the subsequent changes in further size reduction done by the primary crusher.

Jan 1, 2012