Search Documents

By John J. Reed

This paper was prepared as a supplement to the general review by Dr. N. G. W. Cook. His analysis of the problem in terms of the strain energy involved in making the excavation is excellent. It will contribute much towards a clearer understanding of rock behavior and control. Several of the practical applications described herein can be directly related to Dr. Cook's theories and conclusions, and are based on the very same principles. CONTROLLED BLASTING IN ROCK EXCAVATION Generally speaking, the natural rock is a relatively strong and competent structural material, if we conserve its inherent good properties and perhaps reinforce its weak spots. The difficulty often lies in blasting out the tunnel or chamber without damaging the walls and roof we wish to have remain afterwards. Much progress has been made in the last five years in better understanding the controlled excavation of rock. The specialized techniques known as smooth wall blasting and presplit blasting have now developed from the status of curiosities of rock excavation to the point where these techniques are specified in contracts drawn up for such rock excavation projects as tunnels, underground pourer houses, etc. These techniques have been well described and discussed in previous publications; there is no need to reiterate here. It might be well to point out that recent research has demonstrated the effect that inherent rock stress may have on presplitting in certain directions. Material can be presplit most readily parallel to the direction of maximum compressive stress, and this may not always be in the direction desired. Inherent rock stress measurements by stress relief over coring, etc., may have important value in deciding how to best presplit proposed excavations. In addition, recent work at the Colorado School of Mines has demonstrated the feasibility of con-

Jan 1, 1967

By G. T. Lineberry

Underground mine development begins with the positive investment decision to mine and ends with the inception of full-scale exploitation. It incorporates all activities, personnel, and equipment required for creation of underground access to a mineral deposit. Because of the depletion of near-surface mineral resources, the reduced mobility of large surface mining equipment, increasingly stringent environmental constraints, and the introduction of promising innovations to rock penetration and rock excavating equipment (e.g., continuous miners, rock borers), under-ground mining is projected to account for an increased share of worldwide mineral production in the foreseeable future. Without proper engineering during the mine development phase, failure of the underground mining project is axiomatic. A frustration attendant to coverage of the complex area of underground mine development lies not only with the need for treatment of the many disparate specialties within the area but even with the lack of systematization of these specialties in what is recognized as a vital precursor to successful mining. Section17 offers insights into (1) the basic principles of the planning and design process, including baseline assessment, reserve determination, premine planning, and subsystem design (Chapter17.1); (2) equipment selection and sizing, with emphasis on exca-

Jan 1, 2008

By P Hatherly, H Gurgenci

With the depletion of the mineral reserves that can be mined by surface mining, demand for highly productive and safe underground mines will increase. Underground drill and blast techniques continue to be refined but true æmass productionÆ is difficult to achieve. As is evidenced by the longwall mining of coal, alternative mining methods based on mechanised mining can meet the expectations but the issues of how to effectively cut strong rocks, how to define the orebody and how the mechanised miners can be automated and maintained all need to be addressed. CMTE is working in all of these areas. We believe that the oscillating disc cutter may provide the long sought-after breakthrough in mechanised rock cutting. Disc cutters are one of the most robust designs of cutting tool and the cutters attack the rock in a manner which effects direct tensile breakage. The internal cutter drive and the inertial damping mean that the already low cutter forces are not all transmitted back to the machine, making it possible to design lightweight, flexible mining systems. For orebody delineation drill monitoring, drillhole logging and geophysical imaging are key procedures being developed at CMTE. To automate mining machines, work is progressing well in the development of systems for autonomous vehicle navigation and mining robotics. A strategic contribution to maintenance issues is being made through the development of procedures for automatic analysis of used oils, monitoring the strength of mechanical structures, and operating point optimisation.

Jan 1, 1998

By N. G. W. Cook

The conventional cyclic system of deep-level mining by drilling and blasting gives rise to an inadequate degree of stope sorting when mining thin reefs. This results in poor utilization of the capital facilities of a mine in the form of shafts, haulages, airways, and associated equipment. Continuous and controlled removal of the thin gold-bearing portion of the reefs would permit better stope sorting and hence greater utilization of capital facilities. Results of experiments to develop hard-rock cutting machines for mining are reported and the benefits which could be derived from their use are discussed. Mining, from exploration through refining, is essentially a process of sorting in which the payable mineral, or metal, is progressively separated from the other constituents of the earth's crust with which it was originally associated. This takes place more distinctly at each step of the operation. What is it that determines the degree to which sorting should be carried out at each of the several steps comprising a whole mining operation? The formal answer is that degree of sorting at each step which results in the lowest overall cost for the complete separation. In practice, individual steps are chosen from those available in current technology, each of which effects a degree of sorting such that the quantity of material which must be sorted in the succeeding step is economically acceptable. It follows that any new technological development has repercussions throughout the whole mining operation and, more important, that the solution to excessive costs in any one step of the operation may lie not in improving the costly operation itself so much as in increasing the degree of sorting preceeding that operation. This concept, particularly in relation to deep-level mining of thin, tabular gold-bearing reefs in South Africa, is discussed here, and the most recent results achieved in the development of hard-rock cutting machines for stoping more selectively than is possible with explosives are presented. Deep-Level Mining Deep-level mining involves operations which are either not encountered, or are of only trivial importance, in near-surface mining. Near-surface, the major operations are those of rock breaking, transport, and milling. In deep-level mining, hoisting, environmental control, and strata control assume major importance. Some idea of the relative magnitude of these operations may be gained by comparing the separate amounts of energy which are required, or which must be controlled, to effect the various operations when, say, mining a tabular deposit 40 in. thick at 8000 ft below surface, Table 1. It is true that the costs of handling a given quantity of energy are not the same for each operation. Nevertheless, Table 1 does emphasize the fact that the operations of hoisting, strata control, and environmental control are of unique and major significance in deep-level mining. In particular, hoisting and environmental control place a heavy load on the reticulation system of the mine—the shafts, haulages, and airways. Typically, a new, deep gold mine with an annual revenue of about $35 million requires a total capital expenditure of about $140 million of which some $100 million is invested in developing and equipping this reticulation system. The ratio between annual turnover and capital invested of about one-quarter is exceptionally low, and it typifies the poor utilization of capital by the current technology of mining hard rock at depth. The average thickness of the reefs in the new South African goldfields varies from 10 to 30 in.,l and even in the thicker reefs the gold is often confined within a small fraction of the nominal thickness. Nevertheless, it is universal practice to mine these reefs at a stope width of about 40 in. or more, so that the quantity of rock broken in the stopes and hoisted out of the mine is between two and ten times the quantity of rock actually carrying a significant amount of gold. The reason for the adoption of such excessive stope widths is to be found in the method of rock breaking by drilling and blasting. The only free surface to which a blast hole can break is the stope face. It follows2 that each hole cannot have a burden in excess of the height of the free face if it is to break satisfactorily. To

Jan 1, 1971

By C. R. Julian

THE large pyrites ore-bodies, the underground mining of which is to be described, are situated at Rio Tinto in the Province of Huelva in Southern Spain. The situation of the different ore-bodies with relation to one another is shown in Figure 1. It will be seen on the plan that the strike of the ore-bodies is approximately east and west. The geology of the district has been very fully described by Dr. D. Williams (1), so that for the purposes of this paper it will be sufficient to give briefly the salient features o each of the two larger ore-bodies which are being mined by underground methods at the present time. (a) San Dionisio.-This ore-body is the largest single deposit in Rio Tinto, having on its upper levels a length of 3,500 ft. On the upper levels the average width is approximately 200ft. but in places on the lower levels there is a width of 900ft. of un broken pyrites. Diamond-drill holes, without running out of ore, show the ore-body to persist to a depth of at least 1,600 ft. The ore-body in the upper part lies between slate and porphyry walls, but in depth is enclosed in porphyry walls. (b) South Lode.-Faulting is considered to be responsible for the break in the solid ore between South Lode and San Dionisio. On the upper levels, the South Lode ore-body has an unbroken length of 4,000 ft. The massive pyrites has a maximum width of 300ft. and an average of about 100 ft. Ore has been proved to a depth of 1,000 ft., at which depth the ore-body is much reduced both in length and breadth. This ore-body, to the depth at which it has been proved, lies entirely between slate and porphyry walls. The South Lode and the San Dionisio ore-bodies are mined both by open-cast and by underground methods. There is evidence that these mines have been exploited intermittently during the last 3,000 years; but, as is to be expected, no records are available of the tonnage mined prior to the time of purchase by the present company.

Jan 1, 1940

By Carole L. B. Mitchell

The South 180th Street Grade Separation underpass in Tukwila and Renton, Washington, USA, permits vehicular traffic to pass beneath Burlington Northern Santa Fe and Union Pacific railroad tracks. The railroad tracks were temporarily relocated onto a shoofly crossing while the permanent bridges were constructed. The maximum underpass depth is approximately 25 feet (7.6 meters [m]). The majority of the sidewalls are supported using alternating reinforced and unreinforced secant pile walls. Temporary and permanent struts brace the top of the excavation. Because the groundwater is about 15 feet (4.6 m) above the base of the excavation and the subsurface materials are loose to medium dense fill, alluvium, and soft flood plain organics, the base of the excavation was strengthened and sealed using wet cement deep soil mixing (CDSM) methods. During construction, CDSM-treated ground temporarily acted as part of the railroad shoofly shoring while the remainder of the underpass was excavated on either side of active railroad tracks. The combination of secant pile sidewalls and CDSM bottom seal allowed for easy excavation, even during wet conditions. Using a 35-foot-thick (maximum) (10.7-m) CDSM layer both to act as a bottom seal and to resist uplift pressures is a unique, dual-purpose application of CDSM technology in the United States.

Jan 1, 2004

By Richard Crockford

The World Trade Center (WTC) is located on the west side of Manhattan in New York City, approximately 0.5 miles north of Wall Street, and is owned and operated by the Port Authority of New York and New Jersey (PA). As part of the WTC site redevelopment the New York City Transit Authority?s No. 1 subway line which runs through the site below grade, was underpinned so that the soil beneath it could be removed along with the rest of the new east basement excavation. Consequently a scheme comprising micropile installation through and around the existing subway box was designed. The subway had to remain in use throughout save for planned weekend outages to allow a portion of the underpinning to be fitted through or on to the existing structure. At times this involved accessing and drilling from within the subway tunnel under short General Order (GO) Subway shutdown periods. At either end of the subway passage through the WTC site jet grout underpinning was designed to provide support and to complete the excavation and construction of the east basement wall in the areas beneath the subway where it was impossible to install a slurry wall. The jet grout blocks thus formed had to be largely installed around the clock during 53 hour long GO weekend outages and had to overcome severe logistical constraints in and over the tunnel. The jet grout blocks had to provide strengths of at least 500 psi at 3 days and 700 psi at 28 days. The jet grouted soil mass also had to have a level of permeability less than 0.03 feet/day (1 x 10-7 m/s). After an extensive trial program and then production testing it was concluded that the glacial till above the rock proved to be a particularly difficult soil strata to collect test data from and hence the level of observational monitoring was increased to progress the excavation works. Throughout the installation of micropiles and jet grout columns extensive monitoring was in place and prompted a variety of working method changes. The work described in this paper was performed by the Nicholson Construction Company/EE Cruz Joint Venture.

Jan 1, 2008

Heavy mineral deposits are becoming more complex in terms of their compositional variation, particle mineralogy and size distributions, and present challenges for the operation of separation equipment to achieve the required grades and recoveries. Changes in equipment design and concepts potentially provide new opportunities for the beneficiation of heavy mineral sands deposits. The development of a framework for the fundamental understanding of separator performance issues is a first step to develop new machines. This paper will present a first step analysis of electro-static and magnetic separation machines with their application to real separation scenarios.

Jan 1, 2010

By J Channell, G Phillips

"The Chesney deposit, located 4 km south-east of Cobar consists of three copper-gold rich shoots that lie within a larger, copper dominant lode. A fourth gold rich shoot is located adjacent to the main deposit. The deposit exhibits a strong structural control on mineralisation, as brittle deformation during subvertical extension provided the requisite structural traps to precipitate sulfides from solution. It is postulated that the Great Chesney Fault acted as a fluid conduit, conveying fluids to the site of orebody formation. The continual supply of fluids resulted in cyclic brittle deformation when the fluid pressure exceeded the lithostatic pressure and the tensile strength of the Great Cobar Slate.Evidence supports the hypothesis that ore deposit formation was controlled by: a supply of mineralised fluids transported along the Great Chesney Faulta suitable location for the mineralised fluids to accumulate, accommodated by vertical extension and dilation in certain locationsthe creation of suitable structural traps to capture the sulfides. These traps formed as a result of fault-valve behaviour. Understanding the controls on mineralisation enables prediction of the location of other deposits with similar emplacement history, or extensions of current deposits.CITATION:Channell, J and Phillips, G, 2014. Understanding mineralisation controls – a case study of the Chesney deposit, in Proceedings Ninth International Mining Geology Conference 2014 , pp 301–312 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

Rotary kiln incinerators are widely used in the incineration of various types of hazardous wastes. However, the complex transport processes within the incinerator are not well understood. Due to large variations in waste types and difficulties in feed characterization, the incineration process meets great challenges in a smooth operation, and expects uncertainties in the process chemistry and emission control. In order to get better understanding of the incineration process, process simulation was made on the kiln behavior by using Computational Fluid-dynamics (CFD) to characterize gas flow, temperature distribution and waste combustion in the incinerator. Temperature measurement was conducted in an operating incinerator to validate the CFD model. This paper addresses the environmental issues related to the hazardous incineration process, and reports the recent simulation results on gas flow and mixing, combustion heat transfer, and potentials to reduce emissions.

Jan 1, 2002

By Alastair Torrance, Gary Cavanough

Approximately 1.5 million tonnes of ammonium nitrate are transported annually across Queensland, Australia—equivalent to nearly 100 truckloads per day. This is in the form of both AN prill and ammonium nitrate based emulsions (ANE). In a recent incident, a collision involving an ANE tanker resulted in a detonation that caused extensive blast-related damage and led to the closure of a major highway. Had this event occurred within a populated area, the consequences would have been catastrophic. For over a century, investigations into the causes of such spontaneous detonations have been inconclusive. A recently completed industry supported research project has made a pivotal discovery: a surface reaction mechanism leading to hydrogen generation has been identified as a precursor to detonation. If sufficient hydrogen accumulates and subsequently ignites, it can release enough energy to initiate the detonation of bulk ammonium nitrate and ANE. Controlled experiments conducted during the project successfully demonstrated hydrogen-driven detonation events. Previous work by Proulx and Scovira, presented at the 2000 ISEE Conference, described spontaneous detonations in hot, reactive ground and the mitigating effects of buffered emulsions and ANFO. Building upon their observations, this study reproduces similar incidents under laboratory conditions, confirming that hydrogen generation also results from reactive ground interactions. Importantly, the findings challenge traditional assumptions, demonstrating that ammonium nitrate and ANE detonation in reactive environments does not require an ignition temperature threshold, confinement, or a classical chemical decomposition pathway.

Jan 26, 2026

By N Kawashima, R St C Smart, A M. Robertson

This paper focuses on a case study at a base metal mine located in a tropical semi-arid area of Western Australia (WA). It is demonstrated that understanding the geochemical nature of the mine tailings forms an integral part of innovative management strategies developed throughout the life-of-mine (LOM) when planning for mine closure. The tailings are currently stored at an above-ground valley fill tailings storage facility (TSF) and one option for long-term management under consideration is leaving the tailings in situ at mine closure and covering using the concept of an enhanced æstore and releaseÆ cover system.Extensive geochemical and mineralogical studies have found that the geochemical behaviour of the tailings in the TSF is significantly more benign than initially predicted. The sulfide content of the tailings is primarily pyrrhotite, which can be acid-forming, acid-neutral or acid-consuming depending on a number of factors including redox conditions. Tailings pore water at depth is pH neutral with excess alkalinity, low concentrations of dissolved metals and elevated sulfate concentration.Recent geochemical tests on tailings samples indicate that a reduction in the acid potential and a corresponding increase in the neutralising potential of the tailings, through partial removal of pyrrhotite at the ore processing stage, has the potential to further reduce the long-term risk of potential impact to the environment from any TSF seepage. The current work program investigates whether partial removal of pyrrhotite is feasible and secondly, whether this approach is necessary to produce a significantly better outcome at mine closure.CITATION:Robertson, A M, Kawashima, N, Smart, R St C and Schumann, R, 2012. Understanding tailings geochemistry - Continuous learning and innovation when planning for mine closure, in Proceedings Life-of-Mine 2012 , pp 287-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By Komar Kawatra, Joseph Halt

"Bentonite clay has been the traditional binder for iron ore pellets. However, bentonite increases pellets’ silica contents and is expensive. Researchers have proposed lowering bentonite doses by mixing it with other common binders. These mixtures may only be successful if the fundamental bonding mechanisms are understood. For example, what happens when bentonite (physical bonding) is mixed with fly-ash (chemical bonding)? What happens when bentonite is mixed with cornstarch (physical bonding)? In this paper, experiments are described where bentonite was mixed with various ratios of cornstarch and fly-ash, and pellets were agglomerated using 0.66 % w/w binder. Ca(OH)2 and CaCl2 were added as activator and accelerator, respectively, to the bentonite-fly ash mixture. Curves of pellet dry strength vs. bentonite-starch ratio were linear, suggesting the physical-physical bonding mechanisms were compatible - acceptable strengths (> 22 N) were produced at all bentonite-to-starch ratios. This was contrary to bentonite-fly ash mixtures, which displayed dry strength curves with a noticeable minimum due to competing binding mechanisms. Bentonite alone and fly ash alone produced acceptable strengths (> 22 N), but their mixtures resulted in weak pellets. Due to the positive results using cornstarch (CS) binders, the effects of CS solubility in water were investigated using two CS with high and low solubility (60 and 7.5 %). CS was premixed with bentonite at various ratios (0, 20, 40, 60, 80, 100 %). Pellets were agglomerated using 0.66 % w/w binder. The dry strength of pellets ranged from 50-300 N using the high solubility CS mixtures, and from 50-85 N using the low solubility CS mixtures. Fired strengths exceeded 2200 N/pellet at all bentonite-cornstarch ratios. This research showed that cornstarch solubility is an important factor in determining its effectiveness as a binder for iron ore concentrates, but significant work is still necessary before it can be used as a bentonite replacement."

Jan 1, 2014

By NA UMC

Abstract Booklet

Dec 1, 2022

By NA UMC

Abstract Booklet

Dec 2, 2023

By Jean-Marc Lulin

"Depuis 1906, près de 130 gisements ont été découverts dans la inture archéenne polymétallique (Cu, Zn, Au, Ag) du nord-ouest québécois. Une étude régionale du développement du potentiel inier est présentée puis détaillée pour quatre secteurs: Rouyn-Dranda, Val d'Or-Malartic, Bousquet-Cadillac et Matagami.L' analyse est conduite a l' aide des paramètres suivants: temps, méthodes de découverte, profondeur des gisements et poids métal. Les courbes cumulatives illustrant le nombre de gisements découverts fonction du temps montrent une forme générale en ""S"" dont les i'iations de pentes correspondent aux variations dans les taux de couverte. Initiation, réalisation et stabilisation des cycles de décourté sont ainsi mis en évidence. Deux ""bourns miniers"", de 1922 à 1945 et de 1955 à 1965, rassemblent 72 % des mines identifiées sqú à présent.La plupart des mines sont trouvées en subsurface: 90% ont leur mmet entre 0 et 100 mètres de profondeur dont 70 % entre 0 et 10 êtres. Dans le temps, il y a d' abord récolte par prospection puis par ophysique et enfin, développement progressif du potentiel en proeur avec des méthodes composites. Environ 80% du poids métal extrait de 4 camps miniers, couvrant 8% de Ia surface régionale quelques gros gisements dominent /a production.Ces données permettent de proposer une nouvelle approche pour analyse d' une région minière:La distribution de Ia profondeur des gisements en fonction du temps est indicatrice de la maturité d' un camp minier et peut servir a évaluer son potentiel résiduel.L’analyse des courbes en ""S"" permet d’extrapoler les taux de succès relies aux différentes méthodes et met en relief le rôle crucial de I' innovation dans I' exploration.ABSTRACTSince 1906, some 130 deposits have been discovered in the Archean polymetallic belt of northwestern Quebec. In this paper, the development of the mining potential is analyzed at the regional scale and for the following mining camps: Rouyn-Noranda, Val d'OrMalartic, Bousquet-Cadillac and Matagami.The analysis is based on the following parameters: time, discovery method, depth and weight of metal extracted. Curves showing the cumulative number of deposits discovered as a function of time are ""S"" shaped with slope variations corresponding to changing discovery rates. Initiation, realization and stabilization of discovery cycles are thus well represented. Two ""mining booms"", 1922 to 1945 and 1955 to 1965, account for 72% of the mines identified to date.Most exploitable orebodies have been found near the surface: 90 %have their top between 0 and 100 meters, including 70% between 0 and 10 meters. Early discoveries were made by prospecting, followed by geophysics while the progressive development of the depth potential is being realized by a combination of methods. Approximately 80 %of the metal extracted comes from four mining camps which cover 8% of the area, but most of the production can be allributed to only a few large deposits. Based on these data, a new approach to the analysis of a mining region is proposed:1) The distribution showing deposit depth versus time is indicative of the maturity of a mining camp and can serve to evaluate its remaining potential.2) The ""S"" curve analysis can be used to extrapolate the success rate of a specific exploration method and also stresses the crucial role of innovation in exploration."

Jan 1, 1989

By Jean-Marc Lulin

"Depuis 1906, pres de 130 gisements ont ere decouverts dans la inture archeenne polymetallique (Cu, Zn, Au, Ag) du nord-ouest becois. Une etude regionale du developpement du potentiel inier est presentee puis detaillee pour quatre secteurs: RouynDranda, Val d'Or-Malartic, Bousquet-Cadillac et Matagami.L' analyse est conduite a l' aide des parametres suivants: temps, ethodes de decouverte, profondeur des gisements et poids metal. ~~ courbes cumulatives illustrant le nombre de gisements decouverts fonction du temps montrent une forme generale en ""S"" dont les i'iations de pentes correspondent aux variations dans les taux de ~ouverte. Initiation, realisation et stabilisation des cycles de decourte sont ainsi mis en evidence. Deux ""bourns miniers"", de 1922 a ~5 et de 1955 a 1965, rassemblent 72 % des mines identijiees squ' a present.La plupart des mines sont trouvees en subsurface: 90% ont leur fmet entre 0 et 100 metres de profondeur dont 70 % entre 0 et 10 etres. Dans le temps, il y ad' abord recolte par prospection puis par fphysique et enjin, developpement progressif du potentiel en proeur avec des methodes composites. Environ 80% du poids metal extrait de 4 camps miniers, couvrant 8% de Ia surface regionale quelques gros gisements dominent /a production.Ces donnees permettent de proposer une nouvelle approche pour lysed' une region miniere:La distribution de Ia profondeur des gisements en fonction du temps est indicatricede /amaturite d' uncampminieret peut servir a evaluer son potentiel residue/.L' analyse des courbes en ""S"" permet d' extrapoler les taux de succes relies aux differentes methodes et met en relief le role crucial de I' innovation dans I' exploration.ABSTRACTSince 1906, some 130 deposits have been discovered in the Archean polymetallic belt of northwestern Quebec. In this paper, the development of the mining potential is analyzed at the regional scale and for the following mining camps: Rouyn-Noranda, Val d'OrMalartic, Bousquet-Cadillac and Matagami.The analysis is based on the following parameters: time, discovery method, depth and weight of metal extracted. Curves showing the cumulative number of deposits discovered as a function of time are ""S"" shaped with slope variations corresponding to changing discovery rates. Initiation, realization and stabilization of discovery cycles are thus well represented. Two ""mining booms"", 1922 to 1945 and 1955 to 1965, account for 72% of the mines identified to date.Most exploitable orebodies have been found near the surface: 90 %have their top between 0 and 100 meters, including 70% between 0 and 10 meters. Early discoveries were made by prospecting, followed by geophysics while the progressive development of the depth potential is being realized by a combination of methods. Approximately 80 %of the metal extracted comes from four mining camps which cover 8% of the area, but most of the production can be allributed to only a few large deposits. Based on these data, a new approach to the analysis of a mining region is proposed:1) The distribution showing deposit depth versus time is indicative of the maturity of a mining camp and can serve to evaluate its remaining potential.2) The ""S"" curve analysis can be used to extrapolate the success rate of a specific exploration method and also stresses the crucial role of innovation in exploration."

Jan 1, 1990

By Ping Zhang, Xu Ma

Perturbations arising from mining operations significantly affect the stability of rock masses, and the influences aggerates with the rapid increase of mining-operation depths during recent years. The subsurface structures with major discontinuities subject to seismic hazards resulted from the shear-slip behaviors of rock masses. In order to identify the shear-slip regime of discontinuities and calculate seismic moment and seismic energy involved with shear-slip behaviors, we use discrete element modeling to study the shear slip failure along discontinuities in an underground mine. The recorded characteristic and properties of sub-contacts in DEM provide a basis for computing and visualizing the temporal and spatial distribution of seismic moment and seismic energy with mining operations. We computed the seismic energy and seismic moment using the numerical modeling method and the analytic method. We compared the result of summing seismic energy and seismic moment from the subcontacts of numerical models and the result of the analytic method. We confirmed that this tool can be used in comparative analyses. We also found that seismic moment and seismic energy, associated with shear stress drop and shear displacement increase, accumulate in the vicinity of major discontinuities. Mining operations at a greater depth cause greater changes of seismic moment and seismic energy, leading to a higher risk of inducing seismic hazards. Quantifying seismic potential using discrete element modeling can greatly facilitate the investigation of instability of geological discontinuities and thereby can help estimate the potential of seismic hazards.

Jan 21, 2023

By David R. Maneval

The mining of coal in Alaska receives special treatment in the Surface Mining and Reclamation Act passed by the U.S. Congress in 1977 (PL95-87). Section 708 of the Act required that the National Academy of Sciences (NAS) perform a study of "Surface Coal Mining Conditions in the State of Alaska, In Order to Determine Which, If Any, of the Provisions of the Act Should be Modified with respect to Surface Coal Mining Operations in Alaska'. The special committee on Alaskan Coal Mining and Reclamation of NAS completed their study in 1980 and prepared their report (NAS, 1980). At this time, the Secretary of the Interior and the Congress have taken no special action with regard to either special regulations geared specifically to Alaska or to submitting special draft legislation to the Congress requesting amendment of PL95-87. The Alaska Department of Natural Resources (DNR) has drafted legislation which was submitted to and passed by the 1982 session of the State Legislature. The State regulatory agency has also drafted the requisite regulations necessitated by the amendments to the State's Basic Coal Mining Act. It is expected that by mid 1983 DNR will have applied for "primacy" to the office of Surface Mining, U.S. Department of the Interior (OSM). They will be submitting the amended State Law, the revised State Regulations and an operational plan as called for by OSM regulations. The presumption is that primacy will be granted to the State of Alaska under PL95-87. The Usibelli Coal Mine continues to be the only operational commercial mine for coal in the State of Alaska. It produced 7.26 x 10 kg (8 x 10 " T) of coal during 1981. The current mine was started in 1920 by Captain Lathrop, an early developer and pioneer in Alaska. It was continued by Emil Usibelli and was taken over after the death of E. Usibelli (in the 1964 earthquake) by his son Joseph Usibelli who is the current President of, the firm3 Their latest improvement is a 27.5 m (36 yd. )Bucyrus-Erie Dragline which handles most of the overburden removal. The coal is removed by a loader-truck combination. They are currently starting up the use of a unit train loading facility which handles forty cars every two hours. This loading system was a development necessitated by the Sun Eel Export contract. The Alaskan Railroad was a major cooperator in the development of the first unit train loading facility in Alaska.

Jan 1, 1982

By T. Yamazaki, T. Goto, R. Arai, N. Nakatani

The importance of cobalt-rich manganese crusts on the Pacific seamounts for possible future rare metal sources has been recognized these 30 years. The thin layer-type coverage and the micro-topographic undulation of basement affect not only the excavation efficiency but also the economy of mining venture. Because of these distribution characteristics, no economic feasibility has been recognized through the past economic analyses. On the basis of a recent geological study about seamount rocks, a possibility of by-product substrate recovery for phosphorous supply with cobalt-rich manganese crust mining has been highlighted. In the mining model, the substrate rocks are utilized as phosphates for agricultural and chemical usages. Under some preliminary technical and economic assumptions, the possibility of cobalt-rich manganese crust mining venture is examined. The results show a better economy of the venture including the substrate rock usage for phosphorous supply. Introduction Cobalt-rich Manganese Crusts and the Economic Feasibility Cobalt-rich manganese crusts on the Pacific seamounts received attention as potential sources for strategic metals such as Co, Ni, Cu, and Mn, due to their vast distribution and higher cobalt concentration than manganese nodules (Cronan, 1980; Halbach, 1982; Manheim, 1986). In the earlier stage, the geological distribution characteristics were reported (Cronan, 1984; Clark et al., 1984; Misawa et al., 1987; Pichocki and Hoffert, 1987) and a systematic feasibility of the mining was studied (Hawaii DPED, 1987).

Jan 1, 2018