Search Documents

By D. R. Brooks

The Bureau of Mines has tested a dewatering technique for phosphatic clay waste. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen or trommel. In field tests conducted in central Florida, clay wastes containing approximately 4 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO-treated material will dewater to 30 pct solids in 80 days. Pretreatment of phosphatic clay waste with lime lowers the PEO dosage required for dewatering.

Jan 1, 1986

By M. J. Ferrante

Relative enthalpies of V20S from 298.15 to 1,101.0 K were measured at the Bureau of Mines to provide data needed for the advancement of min-eral technology. Enthalpies were measured with a copper-block calorimeter. A sharp melting point was found at 951 K, with [~~ = 15.690 kcal/ mol ] for the standard enthalpy of melting. Tabulated values are given at selected temperature increments between 298.15 and 1,500 K for the standard relative enthalpy [(HO -H~98),] heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)/T]. Standard relative enthal-pies are also given in equation form and combined with data from the literature to derive values of standard enthalpies of formation and Gibbs energies of formation.

Jan 1, 1986

By Maureen M. Foss

Underground coal mining is hazardous due to changing geological conditions. One geophysical method showing promise for in-seam hazard detection is ground-penetrating radar (GPR). The Bureau of Mines recently completed preliminary studies to demonstrate the feasibility of using GPR for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using trans-illumination. Data were gathered on multiple travel paths, and a back projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomographic tech-nique, and the results were compared with those of the actual data. Analysis of the tomographic images shows the presence of the clay vein, although its boundaries are unclear due to the tomography method used. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take. A need has been shown for research involving more sophisticated tomography techniques, transmission studies on thicker coal seams, and reflection studies using the synthetic-pulse system.

Jan 1, 1987

By J. E. Fraley

Full-column anchored resin bolts were first used in underground mines in 1972. These bolts appear to improve support in many roof bolt applications, as indicated by the use of about 30 million resin bolts in 1980. In the mid-1970's, Bureau of Mines in-vestigators began looking for a substitute for resin because of its short supply and rapidly increasing price. The investigators selected accelerated gypsum plaster (CaSO. ·1/2H20), which becomes gypsum (CaSO.· 2H20) when mixed with water. Gypsum makes an effective alternate grout material because it hardens quickly, is readily available, and is inexpensive in comparison with other cementitious materials. The Bureau received a patent (U.s. patent 4,096,944) for a system combining water capsules (wax-encapsulated water) with plaster into cartridges resembling resin cartridges. This report presents the results of tests conducted by the Bureau on the plaster, the water capsules, and their combined use in cartridges. The tests were designed to determine how the gypsum-plaster water capsule bolting system performs and what happens in the hole while the bolt is being inserted through the cartridge. The test results indicate that water capsule plaster cartridges are a workable alternative to resin cartridges under normal or dry conditions.

Jan 1, 1987

By Richard A. Allwes

This Bureau of Mines report presents a procedure for the design of an arch canopy for use in rehabilitating a high-roof-fall area. Only dy-namic line loading of an unbackfilled arch canopy at its crown is considered, and the procedure does not account for an asymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation depends on many variables, including in-mine conditions and the engineering properties of the structure. However, a general evaluation can be based on a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. The design procedure is based on the concept that when an arch canopy is sub-jected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure is that it gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1987

By F. J. Perzak

The Bureau of Mines conducted a flammability study of plastic ventilation ducts. Six rigid 16-in-diam fiberglass-reinforced plastic ducts from five manufacturers were examined using laboratory-scale, large-scale, and full-scale fire tests. The laboratory-scale tests included the American Society for Testing and Materials E162 radiant panel test, the E2863 oxygen index test, and the standardized small-scale flammability test (S3FT) developed by the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, and replicated by the Bureau of Mines. Ten-foot lengths of the same ducts were also subjected to a large-scale vertical fire test, and 20-to 30-ft lengths were tested in a full-scale in-mine fire test at the Bureau's Lake Lynn Laboratory mine. The data from the laboratory-scale radiant panel test and oxygen index test indicated that the ducts were fire-resistant, However, five of the six ducts failed the S3FT and vertical fire tests, and four of the ducts failed the full-scale in-mine tests with flame propagation rates that ranged from 3 to 10 ft/min. The results indicate the need for improved fire-resistant plastic ducts. The good agreement between the S3FT re-sults and the vertical and full-scale tests show that the S3FT provides a good indication of the flammability of fiberglass-reinforced plastic ducting under realistic fire conditions.

Jan 1, 1987

By David K. Ingram

The Bureau of Mines conducted underground mapping and rock strength tests to describe and analyze mine roof conditions surrounding ancient stream channel deposits (paleochannels) in the Pittsburgh Coalbed in southwestern Pennsylvania. Paleochannels in the study mine consist of sandstone and/or siltstone and affect the Pittsburgh Coalbed through erosion and/or differential compaction. Differentially compacted sediments within and adjacent to channel deposits caused slip planes, faults, clay-dike faults, clastic dikes (clay veins), coalbed rolls, and slumped structures. Paleochannels can be predicted by recognizing these features and associated sediments, which allows for modification of long-and short-term mine planning and development. Mine entries located beneath the paleochannel deposits exhibit less stable roof conditions than entries with normal (nonchannel) roof. Paleochannel deposits comprise only one-fourth of the mapped study area; however, they contain one-half of the hazardous roof. This study deter-mined that rock strength evaluations, including rock quality designation (RQD), unconfined uniaxial compressive strength testing, and point-load testing, must be accompanied by underground observations. Suggested remedial support techniques include angled and/or longer tensioned bolts, steel mats or crossbars, steel sets or cribbing, and roof trusses.

Jan 1, 1987

By T. M. Barczak

A primary objective of the Bureau of Mines geomechanics research program is to develop a better understanding of support behavior and interaction of supports with the strata so that supports can be more closely engineered to the geological conditions in which they are employed. Four longwall shield supports were instrumented with an eight-transducer instrumentation array to measure leg, canopy capsule, and compression lemniscate link forces from which resultant shield loading was determined. The instrumented supports were monitored over a 4-month period, producing over 75 shield cycles of resultant shield loading. Resultant loading is the true measure of support resistance, providing both roof-to-floor and face-to-waste support reactions as well as the location of the reaction on the shield canopy. Observed roof support reactions were analyzed, with particular emphasis on horizontal shield loading, since it is the least understood design parameter. Average, peak, and change in shield loading during the mining cycle are discussed. Correlations among data parameters are examined, as is the distribution of support loading at the headgate and midface. Conclusions are drawn as to the effectiveness of the shield support at this installation. Recommendations are made for further research needs.

Jan 1, 1987

By J. F. McIlwain

The Bureau of Mines has investigated fumes generated by selected welding electrodes used in mines in order to help determine their relative health hazard potential. Fumes were generated and collected in an enclosed chamber for subsequent generation rate and chemical constituent determination. Shielded metal arc electrodes from the following groups were tested: AWS types E308-16 and E310-16 stainless steel, ECoCr-A Co-Cr hardfacing alloy, ENiCr Ni, an Mn-Cr buildup alloy, E7018 carbon steel, and EII018-M low-alloy steel. Flux-cored wire electrodes of this last group also were tested. Fume generation rates and the chemical composition of the fumes were measured. From these data, exposure in-dices were determined, which give a relative measure of the health hazard potential of using the electrodes. The effect of welding onto build-up alloy layers on the fume composition also was examined for five of the higher alloy groups.

Jan 1, 1987

By C. F. Wingquist

As part of an ongoing study to determine how the wear of mining tools affects dust generation, the Bureau of Mines has measured bit tempera-ture rise during cutting of abrasive rock. Radial bit wear-flat tem-peratures generated by linear cutting in Berea Sandstone were measured as a function of cutting depth and speed. Depths of cut (DOC) were 1/8, 1/4, and 1/2 in, and cutting speeds were 10, 40, and 80 in/s, respectively. Temperature sensing was accomplished by emplacement of a miniature thermocouple into the center of the wear flat. Temperatures observed ranged from 2000 to 5000 C. Correlation between depth and temperature was weak. Temperature increased linearly with speed at 1/2-in DOC, but data taken at 1/8-and 1/4-in DOC produced inconclusive results. The results indicated that at least for deeper cuts (1/2 in), bit temperature, and therefore wear, can be reduced by lowering the cutting speed.

Jan 1, 1987

By L. A. Haas

The Bureau of Mines, in cooperation with three Minnesota agencies (Department of Natural Resources, Geological Survey, and the Iron Range Resources and Rehabilitation Board), investigated the potential of using glacial lake clay from Minnesota, as well as other areas, as a binder for iron ore pellets. The best clay-characterizing procedures for predicting binder effectiveness were the cation exchange capacity (CEC) using the methylene blue method and the plate water absorption test (PWAT). The best clay binder was found in the Red River Valley. However, compared to a typical western bentonite at the 0.5-pct-addition level, addition of about 2 pct Minnesota clay was required to obtain comparable unfired (green) pellet strengths. Soda ash addition only slightly improved the binding properties of Minnesota clay, but considerable improvement was obtained by the addition of a small quantity of water absorbing organic compounds. For example, with a mixture of 0.5 pct Minnesota clay or paint rock and 0.1 pct pregelatinized starch, the unfired and fired physical pellet properties were about the same as with 0.5 pct of typical western bentonite. The reduction rate at the 40-pct reduction level and the percentage of plus 6.3-mm particles from the reduction disintegration index test were also about the same.

Jan 1, 1987

By Davis E. Traut

TiC14, AIC13, and VC14 were coreduced simultaneously via a Kroll-type magnesium reduction to form an alloy sponge as part of a research effort by the Bureau of Mines to produce titanium alloy powder. Reduction tem-peratures of 750°, 850°, and 950° C, a range of chloride feed rates from 34 to 152 Ib/(ft2·h), and crucible diameters of 7-3/4 and 10-1/4 in were tested. Microprobe analyses using a 40-um-diam spot showed no effect on alloy microhomogeneity (distribution of Al and V in the Ti, considered critical as a powder property), due to changes in process variables within these ranges. Statistical analysis of these data for alloy sponge indicated greater variation in the chemical composition (AI and V) than that found in commercial Ti-6Al-4V plate or Plasma Rotating Electrode Process (PREP) powder. Therefore, a one-step approach to pow-der, such as grinding the Ti alloy sponge, would not produce a powder product of acceptable chemical homogeneity. An approach that homoge-nized the sponge, such as with a melting step, would produce an accept-able powder product with respect to chemical homogeneity.

Jan 1, 1987

By T. M. Barczak

This report describes Bureau of Mines research to develop methods to evaluate loading on longwall roof supports to permit better design and more efficient utilization of these structures in compliance with the geological conditions in which they are employed. The resultant vertical and horizontal force acting on the canopy of a shield can be determined, either from a statically determinate solution assuming rigid-body mechanics and elimination of certain unknowns, or from an elastic solu-tion by analysis of the load-displacement relationship of the shield structure. A two-dimensional rigid-body model is presented that determines resultant shield forces by measurement of leg, canopy capsule, and lemniscate link forces. An elastic solution is presented, in the form of an elastic stiffness model with two degrees of freedom, which describes the load-displacement relationship from the stiffness of the shield structure as determined in the Bureau's Mine Roof Simulator (MRS). The ability of both models to determine resultant forces acting on the shield canopy are evaluated from full-scale tests in the MRS. More advanced numerical models are also discussed as part of the Bureau's continuing effort in the evaluation of roof support structures.

Jan 1, 1987

By P. J. McDonough

The Bureau of Mines designed and tested a hardware-software system for measuring on-line corrosion rates of materials in a rod mill in operation. Currents ranging from 10-6 to 10-3 A and potentials in I-mV increments were converted to a digital signal. The digitized data were frequency-modulated and transmitted from a rotating ball mill to an FM receiver, where they were decoded by computer and then processed in real time using assembly language software. This design approach would allow accurate measurement and control of systems where signals of small amplitude and large ranges are present.

Jan 1, 1988

By R. H. Church

As part of the research effort of investigating the effects of microwave energy upon the chemical and physical properties of different minerals and ores, the Bureau of Mines has conducted basic research into identifying those properties of minerals that are affected by microwave energy, namely, the dielectric constant and loss tangent. These properties were determined utilizing the theory of microwave propagation in a coaxial waveguide filled with a dielectric material and measuring the input impedance with an RF impedance analyzer that operates from 1 MHz to 1 GHz. By knowing the microwave frequency and filling the waveguide with a powdered mineral, the dielectric properties of the mineral sample were determined. From these dielectric properties, theoretical microwave heating characteristics of each mineral could be calculated. These same mineral samples were then irradiated by a 915 MHz 30 kW variable power microwave oven and dielectric heating studies were performed. A comparison of the theoretical heating characteristics and the results from actual dielectric heating studies was conducted to evaluate the dielectric property measurements on each mineral. This report presents the results of the Bureau's research in identifying the dielectric properties of low-loss minerals according to the mineralogical classification scheme along with their irradiation studies. Though far from complete, this study represents some of the more frequently encountered low-loss minerals.

Jan 1, 1988

As part of the Bureau of Mines program to reduce U.S. reliance on foreign suppliers of strategic and critical metals, research was conducted to improve technology for the recovery of critical metals from hardface alloy grinding waste, a form of superalloy scrap. This report describes a hydrometallurgical process that demonstrated on a laboratory scale that 79 pct of the chromium, 97 pct of the cobalt, 99 pct of the manganese, 99 pct of the nickel, and 90 pct of the tungsten could be recovered in chemical form from hardface alloy grinding waste. The process involved deoiling the grinding waste, followed by chloride-based dissolution of the deoiled material. A high-grade calcium tungstate (CaW04) product was recovered from the resultant leach residue by caustic leaching and precipitation. Iron, cobalt, man-ganese, and nickel chlorides were sequentially recovered from the leach liquor by solvent extraction. Amine extractants were used to extract the iron, cobalt, and manganese; decanal oxime was used to extract the nickel. Market-grade cobalt chloride (CoCI2), manganese chloride (MnC12), and nickel chloride (NiCl2) products could be produced directly from the resultant strip liquors. The final raffrnate was a relatively pure chromic chloride (CrCI3) solution that compared favorably with commercial solutions.

Jan 1, 1988

By Russell E. Griffen

With the development of larger mine-haulage trucks in recent years, the visual field of the driver has diminished correspondingly. Specifically, the operator's lack of direct vision in the right front area and directly to the rear constitutes a serious hazard to personnel in nearby small utility vehicles. Recently developed electronic technology has made it possible to supplement the use of mirrors and fresnel lenses to warn the operator of specific collision dangers in the truck's blind areas. This Bureau of Mines report describes the results of a coordinated contract and in-house research program to develop and test in-mine prototype electronic systems to detect the presence of smaller vehicles within the blind areas of large mine-haulage trucks. Each system utilized transmitters installed on the smaller vehicles and receivers installed on the haulage trucks. Transmitting techniques tested included both low-and high-frequency radio waves. On-vehicle testing established the engineering feasibility of each approach. Further private sector product development to improve reliability and reduce system costs is recommended. Mining companies should consider the advantages of each type of system.

Jan 1, 1988

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

By K. Y. Haramy

Coal mine bumps involve the violent, rapid failure of coal and rock around a mine excavation. Deep coal mines with strong roof and floor rocks and high-stress conditions frequently experience face and rib bumps. The bump problem is becoming more severe as mining depth increases, prompting efforts to control high stress in advance of mining. This Bureau of Mines report presents a review of the most widely used methods to detect and destress high-stress zones along coal faces and an investigation of stress-related bump problems and destressing techniques at a cooperating mine. Geotechnical instrumentation and microseismic methods were used to better understand bump occurrences in underground coal mines. Laboratory tests of the drilling-yield method for high-stress detection were conducted to determine the correlation between the volume of cuttings obtained and the magnitude of the applied stress at various confining pressures. A three-dimensional, multiple-seam computer modeling program, MULSIM, was used to evaluate the effectiveness of stress-relief methods. Modeling results indicate that dangerously high-stress areas can be controlled by either proper planning or destressing. Proper mine planning guidelines and destressing methods such as volley firing, hydraulic fracturing, and auger drilling are discussed.

Jan 1, 1988

By Larry A. Lass

The U.S. Bureau of Mines, in cooperation with the Iron Range Resources and Rehabilitation Board, investigated the potential of using northeastern Minnesota papermill waste sludges as a binder for Mesabi Range iron ore (taconite) concentrate. Sludges from five different commercial papermill waste treatment operations were evaluated in laboratory tests. Except for the coarsest sludge, all were fairly easy to blend with the taconite concentrate using conventional mixing methods. The coarsest sludge had to be reslurried at 2 pct solids before adding it to the concentrate in order to obtain pellets without visible sludge clumps. Drying and grinding the sludges made them less effective as binders because of a lower degree of rehydration. On a dry weight equivalent basis, twice as much raw sludge binder was required to obtain similar pellet physical properties as with bentonite; however, the pellets made with raw sludge had superior metallurgical properties. Over 30 pct higher reduction rates and over 1500 C higher softening temperatures were obtained with sludge binder than with bentonite. Sludge D, which had the lowest fiber and the highest alkali metal content, resulted in the lowest reducibility enhancement. Even though more raw sludge was required than bentonite, the sludges have virtually no value, and therefore may provide a cost-effective additive binder for producing improved metallurgical-quality pellets. Large-scale testing has not been done to confirm these laboratory results.

Jan 1, 1989