Search Documents

By K Ehrig, V Liebezeit, Y Li, B Pewkliang, M Smith, E Macmillan

Pre-concentration of low grade ores via the rejection of low/no value materials based on fragment size is the subject of many published papers and studies over the past decade. However, the possibility of upgrading should not limited to low grade ores given the high cost of capital, energy, water, reagents, and ultimately tailings storage across the mining industry. Mining and processing facilities at Olympic Dam consist of an: 1) underground mine where ore is extracted via sublevel open stoping and 2) integrated processing plant located on the surface which produces Cu-cathode, Au-Ag bullion and uranium oxide concentrate. Blasted ore is trucked/trained to underground crushers which produce an ore feed with a product size P80 = -145 mm. Crushed ore is then hoisted to the surface and delivered to the ROM pads via an overland conveyor. The typical copper grade of mill feed is approximately 2 wt%. A rapid assessment of the potential to upgrade Olympic Dam mill feed prior to the ROM pads via rejection of low value materials based on fragment size was completed using existing data. Three separate datasets were utilised to assess the deportment of Cu, U, Au across size ranges of 200 mm down to sub-8 m. Cumulative grade vs cumulative mass distribution graphs for each element were produced. This data clearly demonstrates that Cu, U, Au grades remain constant down to ~212 m, which happens to be the liberation size of the sulfides. Hence, no potential to upgrade the ore stream via rejection of +200 mm - to ~212 m sized materials prior to milling. Mineralisation within the Olympic Dam Fe-oxide Cu-U-Au-Ag deposit (IOCG) occurs as disseminated sulfide grains within granite- to hematite-rich breccias. The typical sulfide grain size is sub-200 m that supports the outcomes of the grade deportment by fragment size study.

Nov 10, 2020

By J. DeYoung

Weak demand for metals and consequent low metal prices resulted in continuation of the depressed state of US mineral exploration activity through 1983. Data collected by Resources for the Future Inc. and The Pennsylvania State University for a cooperative study on mineral exploration activity indicate that US exploration in 1983 fell by as much as 25% from 1982 levels. Precious metals remained the focus of most exploration efforts, as gold and silver prices remained attractive compared to base metals. Reports of 1983 domestic exploration and development activities in several industry journals indicates that about 85% to 90% of those projects were directed primarily at gold and silver. Gold exploration included work by several companies on Carlin- type disseminated gold deposits in Nevada, geological prospecting and drilling in the Wenatchee Gold Belt in Washington, and interest in lode and placer gold properties in California, especially by several small Canadian firms. Precious metals exploration projects were also reported in Alaska, Arizona, Colorado, Montana, New Mexico, Oregon, South Dakota, and Utah. There was also tome precious metal exploration activity in the eastern US. Development continued at the Ropes gold mine near Ishpeming, MI, and companies explored historic gold-producing areas in the Southeast. Some exploration for nonprecious metals took place last year. Stratabound copper-silver deposits were examined in western Montana, and US Borax continued exploring molybdenum resources in the Misty Fjords area in Alaska. Work on these projects during 1983 may have been stimulated by time limits on the availability of certain federal lands for exploration more than by projected improvements in metal markets. During 1983, several papers were published on mineral exploration strategies and the future of US exploration. David Watson of Raymond Kaiser Engineers, in a paper presented at the 1983 AMC Mining Convention, forecast increased exploration activity for gold and silver because of world economic conditions. He added that antimony, manganese, chromium, graphite, mercury, tantalum, tin, and barite are also likely targets based on their limited domestic reserve availability. He cited concern over reported subsidized mineral production by foreign producers and US regulatory and land-planning policies as retarding mineral exploration activity. Douglas Cook of Freeport Exploration Co., at the same meeting, presented a paper that showed that a 1950-75 period of vigorous exploration has been followed by a period where acquisition has replaced exploration as the predominant means of acquiring new mineral properties. At a December IIASA conference on "The Economics of Mineral Exploration," in Vienna, Austria, A. Rose and R. Eggert of The Pennsylvania State University pointed out that recent exploration decisions tend to rely more on evaluating production costs and comparing them with existing deposits, rather than on return of

Jan 5, 1984

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni, 16 per cent Cr, 35 per cent Ni, 12 per cent Cr, 60 per cent Ni, etc ) in recent years has been accompanied by continued demands by the consumer for improvement in properties The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper† The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure The creep-test laboratory constructed for the American Brake Shoe and Foundry Co is designed to permit 1000-hr tests in the temperature range of 1200° to 2200°F with a choice of applied stress extending from 50 to 50,000 lb per sq in in increments of 50 lb per sq in To simplify the calculation of weight combinations, the loading beams (Fig I) are provided with counterweights to eliminate the tare The precision of the knife-edges (10 1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle Check of the loading weights proved the maximum error to be 0 06 per cent Axial alignment is provided by crossed knife-edges in the grip seats The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U S Steel Corporation An 80 per cent Pt, 20 per cent Rh No 19 B and S gauge wire is used as the heating element The details of construction are shown in the radiograph reproduced in Fig 2 The windings are held in place on an alundum tube with alundum cement, the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F over a 4-in gauge length (Fig 3) To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, H. S. Avery

THE increased use of heat-resistant alloys (26 per cent Cr, 12 per cent Ni; 16 per cent Cr, 35 per cent Ni; 12 per cent Cr, 60 per cent Ni; etc.) in recent years has been accompanied by continued demands by the consumer for improvement in properties. The manufacturers of these materials, of necessity, have resorted to more critical studies of the basic causes of variations in fundamental properties. To keep pace with the need for augmented information, previous techniques of investigation have been refined and new test methods and instruments created. It is the purpose of this paper to describe the apparatus, experimental technique and precision of measurement that were employed in the exploration of properties of heat-resistant alloy presented in a companion paper.? The detailed precautions in experimental procedure essential for attainment of accurate and comparable data at elevated temperatures cannot be too highly emphasized. THE CREEP TEST Since the fundamental concepts of creep testing have been recognized for the past 20 years, present interest is restricted to refinements in equipment and experimental procedure. The creep-test laboratory constructed for the American Brake Shoe and Foundry Co. is designed to permit 1000-hr. tests in the temperature range of 1200° to 2200°F. with a choice of applied stress extending from 50 to 50,000 lb. per sq. in. in increments of 50 lb. per sq. in. To simplify the calculation of weight combinations, the loading beams (Fig. I) are provided with counterweights to eliminate the tare. The precision of the knife-edges (10.1 ratio) is such that a 10-gram weight placed on the upper specimen grip will be exactly balanced by a 1-gram weight attached to the loading shackle. Check of the loading weights proved the maximum error to be 0.06 per cent. Axial alignment is provided by crossed knife-edges in the grip seats. The furnaces are similar in design to those of Crane and Company, Battelle Memorial Institute, and the U.S. Steel Corporation. An 80 per cent Pt, 20 per cent Rh No. 19 B. and S. gauge wire is used as the heating element. The details of construction are shown in the radiograph reproduced in Fig. 2. The windings are held in place on an alundum tube with alundum cement; the distribution of turns is adjusted to give a maximum temperature gradient of ± 1°F. over a 4-in. gauge length (Fig. 3). To avoid sharp temperature differentials at the ends of the test section, the length of the furnace is four times the gauge length. Sixteen-inch coupons are used to reduce the temperature of the threaded

Jan 1, 1942

Precision surface mining is increasingly occupying a significant role in open pit mining. Improvements in technology now allow continuous surface mining of material well above 140 MPa (20 300 psi) efficiently and cost effectively when compared to drilling and blasting/primary crushing methods. These include the elimination of the use explosives and primary crushing, the ability to precisely extract the ore from the waste, or separate ores of varying chemistry and mine thin seams and non-homogenous orebodies cost effectively. In addition, precision surface mining extends the useful life of a mine by extending the mine boundaries. It can expand production capacity in existing mines and is particularly cost effective in greenfield start-up mines. Precision mining techniques result in higher percentage recoveries. This paper reviews several of these techniques for the Terrain Leveler« surface excavation machine (SEM), and shows their impact. Vermeer's current approach to precision surface mining is utilisation of the T1255 Terrain Leveler SEM. Several units have been proven in round-the-clock, seven day operations throughout the world. Among other innovations are design simplicity, stability, maneuverability, rear-mounted tilting drum and top-down cutting. The impact of these items are discussed in more detail in the paper. After a detailed analysis of the importance of machine availability on overall mine performance, Vermeer has extended its equipment line to include a direct-drive option for its T1255 Terrain Leveler SEM. In addition, improvements in dust suppression are presented. While the T1255 Terrain Leveler SEM is of optimum size and cost in small and medium sized mines, Vermeer has recognised that larger mines require larger machines with increased capacities. Vermeer will prototype the T1655 Terrain Leveler SEM later this year. Specifications of this machine and up-to-date preliminary results are presented. A discussion of the role of each machine size and driving mechanisms are included. Finally, the next stage in Vermeer's providing solutions to the surface mining community will be described - a continuous loader. The impact on current mine planning is presented using a detailed computer program developed for studying the impact of loading techniques and higher production rates on mine plan optimisation.

Dec 6, 2010

By Nn Li

Energy consumption in commercial buildings has been increasing rapidly in the past decade. The knowledge of future energy consumption can bring significant value to commercial building energy management. For example, prediction of energy consumption decomposition helps analyze the energy consumption patterns and efficiencies as well as waste, and identify the prime targets for energy conservation. Moreover, prediction of temporal energy consumption enables building managers to plan out the energy usage over time, shift energy usage to off-peak periods, and make more effective energy purchase plans. This paper proposes a novel model for predicting heating, ventilation and air conditioning (HVAC) energy consumption in commercial buildings. The model simulates energy behaviors of HVAC systems in commercial buildings, and interacts with a multiagent systems (MAS) based framework for energy consumption prediction. Prediction is done on a daily, weekly and monthly basis. Ground truth energy consumption data is collected from a test bed office building over 267 consecutive days, and is compared to predicted energy consumption for the same period. Results show that the prediction can match 92.6 to 98.2% of total HVAC energy consumption with coefficient of variation of the root mean square error (CV-RMSE) values of 7.8 to 22.2%. Ventilation energy consumption can be predicted at high accuracies (over 99%) and low variations (CV-RMSE values of 3.1 to 16.3%), while cooling energy consumption accounts for majority of inaccuracies and variations in total energy consumption prediction.

Aug 1, 2013

By N. I. Aziz, I. Tague, P. Mackenzie-Wood

The recent mine disasters in Australian coal mines have initiated an introduction of Self-Contained Self-Rescuer (SCSR) as component in the development of new escape strategies for miners. These self-contained self-rescuers are closed circuit, demand sensitive breathing apparatus that make oxygen available to the wearer for a nominal period of time. Their operation is completely independent of the surrounding atmosphere. Once properly donned, the SCSR can assist a miner to escape from an area containing smoke, toxic gases or an oxygen deficient atmosphere. The duration of a typical SCSR is usually taken at the point of complete collapse of the breathing bag which is accompanied by an increase in breathing resistance and inhaled levels of carbon dioxide. Because the oxygen consumption (V02) and the heart rate are correlated, a prediction of V02 and consequently the duration of an SCSR can be made by monitoring the heart rate. Thirty-seven volunteers participated in field simulated escape trials at four underground coal mines. The results from the field trials suggested that oxygen consumption depends on the heart rate, the body weight and exercise rating of the miner. All the volunteers were asked to fill out the questionnaires to evaluate the performance of the units. The miners indicated that they could tolerate the inhaled temperature without any difficulty to breathing resistance. A complete statistical analysis of the field results is also presented.

Feb 24, 1997

By A. Adeli, A. V. Metcalfe, E. Addo, E. Sepulveda

"The accurate modelling of geometallurgical data can significantly improve decision-making and help optimize mining operations. This case study compares models for predicting copper recovery from three indirect test measurements that are typically available, to avoid the cost of direct measurement of recovery. Geometallurgical data from 930 drill core samples, with an average length of 19 m, from an orebody in South America have been analysed. The data includes copper recovery and the results of three other tests: Bond mill index test; resistance to abrasion and breakage index; and semi-autogenous grinding power index test. A genetic algorithm is used to impute missing data at some locations so as to make use of all 930 samples. The distribution of the variables is modelled with D-vine copula and predictions of copper recovery are compared with those from regressions fitted by ordinary least squares and generalized least squares. The D-vine copula model had the least mean absolute error. IntroductionIn this paper we compare the use of D-vine copula, generalized least squares (GLS), and ordinary least squares (OLS) for modelling geometallurgical data from an orebody in South America. The first objective is to construct models for predicting copper recovery (Rec) from the Bond mill index test (BWi); resistance to abrasion and breakage index (A*b); and semi-autogenous grinding (SAG) power index test (Spi). This involves fitting a D-vine copula and regression models fitted by OLS and GLS. The second objective is to investigate the performance of the fitted models for predicting Rec (Willmott and Matsuura 2005).Traditional resource model approaches either ignore the mineral processing characteristics of extracted tonnages or treat processing as an independent component of a mining operation. The net present value (or any other objective) can be truly optimized only by considering the mining operation as an integrated system in which net value is defined as the end-product that the company sells. This approach requires the resource model to be extended to include all relevant rock properties and processing responses."

Mar 1, 2019

By M. Hepokoski, M. Klein, L. Yan

"NIOSH research has shown that heat/humidity buildup is a major concern within coal mine refuge alternatives (RAs). These high temperature and humidity levels inside an RA may expose occupants to heat stress. Due to the safety risks associated with testing using human subjects, NIOSH partnered with ThermoAnalytics to create detailed thermal simulation models of RAs with human occupants. The objective of this effort was to predict a miner’s core temperature response and moisture loss in environments that may be encountered in a coal mine RA. These parameters were studied across a range of temperatures and relative humidity values to determine if the current 95°F apparent temperature limit for RAs is reasonable. The results indicated that the 95°F apparent temperature limit is protective, provided that miners are supplied with sufficient water. The results also indicated that the body core temperature did not reach dangerous levels even at an apparent temperature of 130°F. However, the results show that moisture loss increases with apparent temperature. Therefore, if the apparent temperature limit were increased, the water provided in an RA would have to be increased to offset moisture loss. INTRODUCTION The purpose of this effort was to predict a miner’s core temperature and moisture loss (sweating and respiration) in environments that are likely to be encountered in a coal mine refuge alternative (RA). A range of temperatures and relative humidity were studied to determine whether the current 95°F Steadman apparent temperature (AT) limit and 2.25 quart/day water requirements for RAs as mandated by the Mine Safety and Health Administration (MSHA) are reasonable [1, 2]. The effects of metabolic heat rate (activity level), miner size (height and weight), and pose (sitting or lying) on core temperature and moisture loss were also studied. MODEL DESCRIPTION TAITherm thermal modeling software (ThermoAnalytics, Inc.) was used to simulate humans in RA-like environments within a range of temperature and relative humidity combinations. The TAITherm Human Thermal Model (HTM) predicts the dynamic thermal response of the simulated miners while accounting for clothing, human tissue thermal properties, and active thermoregulation. The following sections describe the HTM in more detail, the thermal model setup for this analysis, and core temperature and moisture loss metrics found in published literature. Human Thermal Model Overview The TAITherm human thermal model was used to simulate the heat generated by the shelter occupants, and to predict the miners’ skin and core temperatures along with their sweat evaporation rates. The thermoregulation model simulates the process by which the body attempts to maintain a constant core temperature by considering the effects of shivering, sweating, and changes in skin blood flow. This model calculates surface and deep tissue temperatures within the human body as described by a surface mesh."

Jan 1, 2017

By Greg Partington, Darryl Thorburn, Charlene Wildman, Elisa Puccioni, Connie Payne, Campbell McKenzie

"Mineral prospectivity modelling of polymetallic nodule deposits has been completed over the Cook Islands Exclusive Economic Zone (CIEEZ) using the GIS based Weights of Evidence modelling technique. Polymetallic nodules, also known as manganese nodules, have been explored as a possible resource for a number of metals including cobalt since the early 1970s. Recent data on the nodule composition and abundance in the CIEEZ has led to a renewed interest in the prospectivity for manganese nodules in the region. The predictive modelling has used the most recently accepted mineral model for polymetallic deep-sea nodule deposition to identify factors that are most likely to map the presence of this type of mineralisation in the CIEEZ.Manganese nodules form on the deep seafloor as concretions formed by concentric layering of iron and manganese hydroxides around a core and they grow at a very slow rate, on the order of millimeters per million years. The available data for the CIEEZ indicates a greater abundance in the area of nodules formed by hydrogenetic processes, which are the result of slow precipitation of metallic components from seawater. The environment in which the nodules are most abundant is at depths between 4,000 m and 6,000 m in areas of low sedimentation rate. Hydrogenous nodules commonly grow on siliceous and pelagic clay sediment, they are less common on other types of sediment."

Sep 1, 2014

By J Q. Shi, M Karakus, Y Liu

Predicting the spatial distribution of rock mass properties in cave mining is a critical challenge. In this study, we introduce a novel machine learning-based model to advance our comprehension of rock behaviour. This model specifically focuses on the spatial distribution of rock mass and mechanical properties, a crucial aspect of our understanding of rock mechanics. Our model is inspired by the recognition that neighbouring information serves as crucial prior knowledge for predicting the spatial distribution of these properties, wherein closer neighbours are likely to exhibit similar characteristics. To effectively capture and model these neighbour relationships, we design a neural network-based model to map the spatial locations within the data set into a new highdimensional space. Within this transformed space, we utilise Euclidean distance to identify N neighbours. Leveraging these neighbours, we introduce a straightforward yet highly effective approach—label propagation—to construct a graph that illustrates neighbour relationships. This graph not only facilitates the prediction of the spatial distribution of rock mass properties but also offers a measure of uncertainty for these predictions. We validate the proposed method using a real rock data set and showcase its efficacy in capturing intricate relationships and distributions within rock properties, enabling precise predictions across diverse spatial scales. Our results underscore the potential of machine learning-based approaches to revolutionise the field of rock mechanics, providing valuable insights applicable to geotechnical engineering, mining, and other sectors where an accurate understanding of rock properties is paramount. This model has direct practical implications, offering a new tool for geotechnical engineers and mining professionals to enhance their understanding and prediction of rock properties, thereby improving safety and efficiency in their operations.

Sep 1, 2024

By M J. Nugus, F Clark, E J. Hill, J T. Carswell, J S. Cleverley, N H. S Oliver

High-nugget gold orebodies are difficult to model in 3D because samples from diamond drill core are generally too small to provide reliable estimates of the gold content of the larger body of rock, and therefore interpolation of gold assay values between drill holes is also unreliable. As a result, gold resources are generally underestimated in areas of high nugget. In practice, proxies for gold mineralisation, such as presence of alteration, specific structures or high vein density, have been used by geologists to predict rocks which are favourable for mineralisation. However, there has been no automated method for combining the predictive capabilities of several proxies, except by human judgement.We have been developing a method to combine several different types of geological features or geochemical analyses into a single measure using conditional probability. Conditional probability provides a meaningful numerical measure for the favourability of rocks for containing high-grade gold mineralisation. This measure can be interpolated in the exploration space, providing a sound basis for a 3D model of the orebody. We have developed this technique using data from the Sunrise Dam Gold Mine, which is a high-nugget orebody hosted in a structurally complex Archaean greenstone belt and which has historically proved to be a very challenging orebody to model.CITATION:Hill, E J, Nugus, M J, Clark, F, Oliver, N H S, Cleverley, J S and Carswell, J T, 2013. Predictive three-dimensional modelling of nuggety gold orebodies, Sunrise Dam, Western Australia, in Proceedings World Gold 2013 , pp 463-468 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By H Asche

The proposed Rockwater Power Project is a hydropower development on the Waitaki River in the South Island of New Zealand. The proposed development will have an installed capacity of 250 MW with a peak flow capacity of 260 m3/s. The project commences at Lake Waitaki and extends some 35 km downstream on the north bank to a surface power station at Stonewall. Flow is returned to the Waitaki River via an outfall channel.The tunnelling for the project is through Greywacke, which comprises Permian and Triassic age marine sediments that are well indurated and weakly metamorphosed. The rock mass is jointed and sheared and there are frequent faults, which range up to hundreds of metres in width. Three 12 m diameter tunnel boring machines (TBMs) are proposed to excavate the 35 km long tunnel.The paper describes the development of the tunnel alignment, rock mass classification, design of the support, rock and hydraulic loads, support installation options and construction sequencing.The alternatives of rock bolts and shotcrete and segmental lining were both investigated and are discussed. Support using rock bolts and shotcrete offers the potential of rapid construction with minimum support cost when the ground conditions are good, but delays due to support installation increases with deteriorating ground conditions. In contrast, segmentally lined tunnels offer greater certainty in cycle time with reduced program risk. Both options are described and discussed.The horizontal alignment is affected by the presence of major fault zones, which are either avoided, or pretreated by driving conventional tunnels through in advance of the TBM delivery, topographical constraints with the rugged topography and operational hydraulic constraints. Construction requirements, future power station operation and the minimisation of leakage from the tunnel have all impacted on the vertical alignment.The number and sequencing of TBMs to be used is discussed in terms of program time and risk minimisation.

Mar 8, 2011

By M. Vaccarini

In this paper a possible methodology to supplement a predictive control approach is reported. The benefits deriving from the application of a predictive control on complex buildings lay on its capability of adapting in advance to the conditioning needs of indoor environments. In fact, the mere reactive control is usually affected by response delays, mainly determined by latency intrinsic in systems and by the massive nature of buildings, which slows down their response to changeable inputs. Hence, systems are too often solicited at their maximum power to recover against comfort deficiencies, and high consumptions are had. This paper reports on the application of a predictive approach to the Passeig de Gracia (PdG) metro station in Barcelona, which is a considerably high energy demanding building and where ventilation systems are used to control both comfort and air quality. Although an extensive simulation for estimating energy savings obtainable through that approach is currently ongoing, in this paper we detail the several components which make up a ?predictive control framework? and we perform a preliminary demonstrative simulation. In particular, the whole setup is formed by: a detailed model of PdG, which simulates the station?s ?real state?; a control model, which optimizes a given cost-function; probabilistic predictive models to infer the future state of the systems, given the assumptions on the control actions by the control module. The outcomes of this paper show that the procedure is applicable and preliminary results over a short simulation horizon of half a day are reported.

Aug 1, 2013

In a previous study, various pyrite depressants were examined to improve the flotation performance of a copper-sulfide ore. Optimal results from this study were used to examine the effect of elevation on recovery and grade. Tests were conducted at elevations of 3350, 1735, 610 and -760 metres, consisted of five repetitive experiments for statistical analysis, and were performed both with and without airflow control. Tests were also performed in a glove box at Montana Tech to mimic the pressure conditions. Results indicate that both recovery and grade are dependent on pressure via bubble size and airflow suggesting that pressurised flotation cells should be considered for operations, particularly those at high elevation. Economics are extremely favourable for implementation because ensuing capital expenses are inconsequential with minimal time for return-on-investment.

Jan 1, 2005

By AIME AIME

ARRANGEMENTS for the Annual Meeting of the Institute were well advanced at the end of December as the following program will show. Heretofore this has been printed separately, but its inclusion in the Annual Review issue of MINING AND METALLURGY will, it is hoped, make it more easily available for reference until the final program is issued, which will be distributed at the meeting. Added details will appear in the February issue. Last year's meeting drew a record crowd of over 2300 which should be exceeded this year. Early reservations at the headquarters hotel, the Waldorf-Astoria, or any other convenient hotel are desirable, as are prompt reservations for the Annual Dinner. No one need worry about too much speechmaking this year, for the honors will be awarded and accepted in a few words instead of a few paragraphs, in seconds rather than minutes.

Jan 1, 1939

By Dubois Eastman

BEHIND the contrasting liquid-fuel technologies of Germany and the United States lie the basic differences of scarcity and abundance. The chemists and engineers of each nation have developed processes that accommodate available raw materials. In the United States, processing is based on an abundant supply of petroleum, which is refined into a variety of fuels and lubricants. Germany has little indigenous petroleum but has a readily available supply of coal that can be converted into liquid fuels and lubricants. As a result, in Germany several basic processes have been developed for the conversion of coal into synthesis gas (carbon monoxide and hydrogen). In turn, this gas is processed into products. As a normal function of its researches into petroleum processing, the petroleum industry in the United States has made careful studies of various conversion and synthesis techniques. A number of oil companies are carrying out independent development programs with the aim of synthesizing hydro- carbon products that can be marketed at a price that will compete with the price of refined petroleum products. American oil companies hope to perfect synthesis processes that will directly benefit the consumer. A good example of progress in these terms is the synthesis plant at Brownsville, Texas, which is based on the conversion of natural gas to synthetic fuels and other valuable products. When this plant is operated at near capacity, it is expected that the products will be able to compete favorably for the consumer dollar. The complete gasification of coal is a technique well rooted in history. As a controlled process on a small scale, it goes back centuries. As a practical technique on a commercial scale, it dates back to 1839, when "producer gas" appeared in Germany for limited industrial use. By 1873, "water gas," or "city gas" as it is sometimes called, was being manufactured commercially in the United States for use in heaters and stoves. The water-gas process was the cornerstone for modern synthesis. To older methods that were concerned only with carbon and oxygen reactions, it added hydrogen by means of steam. Thus far the goal of conversion was to produce gas for heating, lighting, industrial use, and cooking. The long step forward to synthesis was made in 1927, when Germany started to make gasoline from coal by means of the revolutionary Bergius hydrogenation process. A year earIier, Franz Fischer and Hans Tropsch had announced their process, which finally reached the

Jan 1, 1953

Development of aggregate resources for use in structural concrete has been encouraged in Japan to support infrastructure improvement and national land conservation. Natural aggregate is a valuable resource necessary for sound economic development, and its importance is growing. After completion of aggregate mining projects, planting and afforestation are implemented. But sandy soil in excavation sites is not optimum for the growth of vegetation, and many years are needed before forests are restored. Planting techniques should be improved to support efficient reforestation in a shorter period of time. For this purpose, problems hampering growth of vegetation must to be solved through application of physical and physicochemical techniques to ensure that the environment and the ecosystem will be conserved in project sites.

Dec 6, 2010

By Mohamad Omarei, S. M. Sadrameli

"The aim of this research work was to produce biodiesel (fatty acid methyl esters, FAME) from canola oil using KOH loaded on y-Al203 support as a heterogeneous catalyst. Different parameters such as effects of the molar ratio of methanol to oil, catalyst amount and reaction time on the yield were investigated. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were used for characterization of the catalysts. A biodiesel yield of 86.67% was obtained under catalyst preparation and transesterification conditions of calcinations temperature of 773 K, 4 h of reaction time at 338 K, and using 3.5 wt% catalysts and molar ratio of methanol/oil of 15:1. The leaching of potassium species in the spent catalyst was observed.1. IntroductionBiodiesel is an eco-friendly and alternative energy source for diesel engines that can be synthesized by transesterfication of vegetable oil or animal fat with alcohols [1 ]. There are four principal approaches to the synthesis of biodiesel involving the transesterification of the triglycerides of the plant oils and animal fats: base catalysis [2], acid catalysis [3-5], employing supercritical alcohol conditions [6] and enzyme catalysis [7]. The commonly used homogeneous catalysts are NaOH, KOH and their alkoxides. Homogeneous alkali-catalyzed transesterification is much faster than acidcatalyzed transesterfication [8]. However, a large amount of water is required to transfer the catalysts from the organic phase to a water phase after the reaction. Therefore, it is considerably more costly to separate the catalyst from the produced solution [9]. These disadvantages could be removed by use of a heterogeneous catalyst [10]. The use of heterogeneous catalysts eliminates the neutralization step, hence it results much easier to separate from liquid products. Also, they can be designed to give a higher activity and selectivity and to have longer catalyst lifetimes [11]. A large number of different heterogeneous catalysts have been synthesized for biodiesel production. For example, calcined Mg-Al hydrotalcites [12], zeolite and metal catalysts [13], metal oxides such as calcium oxide (CaO) [14], magnesium oxide (MgO) [15], zirconium oxide (Zr02) [16], and supported catalysts [17] have been investigated as heterogeneous catalysts. CaO and MgO are most frequently used heterogeneous catalysts for biodiesel production [18]. In this present work, we aimed at developing an efficient catalyst for transesterification of canola oil. We have prepared KOH/ Al203 by impregnation and applied to determine the optimum conditions for biodiesel production. Three different variables including reaction time , alcohol to oil molar ratio and catalyst loading with may influence the quality of the produced biodiesel were optimized. Moreover, SEM (scan electron microscope), XRD (X-ray diffraction) and XRF were used for characterization of the catalysts."

Jan 1, 2012

By W. C. Lacy

It is the responsibility of educators to look ahead and prepare young engineers and scientists to cope with industrial and social problems of the future. We are faced with a review of history as well as prophesy of the future. The mining industry exists in a "bubble" with little interaction or communication with the outside. This isolation must be broken down if the industry is to survive in the U.S. and Canada. The ability to communicate with the general public and public officials is essential. Many changes are occurring that will require readjustments in technology and staffing. Aging population will result in raising retirement and increasing available workforce. This may force shorter working weeks to supply additional jobs. Environmental concerns will likely direct more attention not only to these concerns during mining, but to planning for post-mining land usage. Retraining and up-dating educational programs are required to cope with these changes.

Jan 1, 1994