Search Documents

By Douglas J. Harvey, Chi-Mou Ni

"This paper presents an analysis technique for the solidification of metal castings. This method, based on a modified finite difference scheme with an irregular mesh, is capable of dealing with the complex geometries of castings. The nonlinearities in material properties of specific heat and thermal conductivity, arising from the phase change during solidification, are accounted for in the step-by-step calculations. Two solidification problems are solved with this analysis technique and the calculated results compare satisfactorily with experimental data. IntroductionCasting process design engineers are often faced with the difficult problem of designing castings to be produced porosity-free. Since the solidification of metal is affected by many interacting variables such as the thermal conductivity, density, and specific heat of both the molten metal and the mold, it is easily seen why this is a difficult task.Typically, casting tooling design is an intuitive process which builds on past successful methods. After processing equipment is constructed, trial castings are made and examined for dimensions and integrity. Changes in the tooling are generally required to improve casting soundness or to reduce cycle time. In the permanent mold process, tooling is complex and difficult to alter after initial construction. The water-cooled steel molds are part of the complete automated system. Associated holding furnaces, pouring ladles, casting conveyers, and utility connections all make other than minor adjustments a costly and time consuming task. An analytical method for using the principles of heat transfer for predicting solidification patterns would be of great value in the permanent mold process by minimizing costly changes."

Jan 1, 1986

By Oscar Restrepo, Juan C. Nino, Henry A. Colorado

New and extraordinary physical-chemical properties of materials at nanoscale open up new applications for the building and infrastructure industry such as structural reinforcements, electronic properties and energy harvesting. Therefore the issues and risks associated with the manufacturing of nanomaterials are now of big concern due to the large volumes and typical processing involved in this industry. This paper presents a discussion and selected applications of nanotechnology in the construction and building materials: from metals and alloys, clay and minerals, ceramics, cement and concrete, asphalt, wood and composites, to finishing systems and some of the most used characterization techniques. Besides the progress in some areas, nanotechnology is just emerging in this field, with many challenges and opportunities, problems unsolved and business opportunities. A discussion regarding the potential health issues and risks of using nanomaterials for workers and the potential environment effects is included as well. New images and diagrams are presented and discussed.

Mar 1, 2018

By Jordan Mayorga, Joseph Kopp, Robert Boehm, Daniel P. Cook

"Solar generated power has long been considered a useful energy source only for low-energy density and non-mission critical use, such as providing electricity for residential applications. The success of Concentrating Solar Power (CSP) facilities, such as the 64 MW Nevada Solar- 1 near Las Vegas, have demonstrated that solar does have application to high energy density industries such as materials and chemical production. This paper will discuss the current operating con_guration of the Solar-1 facility and show how proposed modi_cations, such as addition of thermal storage and use of liquid salts as the working uid, can further improve the e_ciency and energy production of the plant.IntroductionThe United States as a nation is the largest consumer of energy in the world at an estimated 29 trillion kWh per year[1], which is roughly 15% of total global energy consumption[2]. On a per capita basis, the United States also leads most of the world, using an average of 96,000 kWh per person[3]. Roughly 40% of the energy consumed in the United States was produced from petroleum, 23% from coal, 23% from natural gas, 9% from nuclear and the remaining 5% from renewable sources such as solar, geothermal, wind, and hydroelectric[1].Energy demands associated with the industrial-scale production of chemicals and materials is a signicant portion of the United States total energy consumption. Roughly 33% of the energy consumed in the United States is used by the industrial sector, with 22% of this amount used in chemical production, 16% used in petroleum rening, and 14% used in the smelting and rening of metals[1]. Energy costs are also a signicant, if not the most signicant, portion of the total production costs for many materials. For example, roughly 30% of the cost of producing aluminum is the electricity used in the Hall-Heroult process [4], while the cost of energy is roughly 15% of the total cost of producing steel products [5].The primary sources of power for the industrial sector have been coal, petroleum, hydro- electric and nuclear. The use of alternative energy sources, e.g. solar, wind, geothermal, for industrial materials production has been slow in coming because they are intermittent and low-energy density sources, i.e. no solar power at night, no wind power when the air is still, etc. The success of Concentrating Solar Power (CSP) facilities, such as the 64 MW Nevada Solar-1 (NS-1) near Las Vegas, have demonstrated that solar can have application to high energy density industries such as materials and chemical production.This paper will discuss the current conguration of the NS-1 facility, and potential modications to the facility that will increase both its power e_ciency and power density."

Jan 1, 2010

By K. Osseo-Asare

It is possible to form a two-phase system in certain polymerlinorganic salt/water mixtures, such as those containing the polymer polyethylene glycol (PEG). Such aqueous biphase systems have many of the separation characteristics of conventional solvent? extraction systems, but are environmentally friendlier. Just like the well-known organic solvent/water two-phase system, the top polymer-rich phase is more hydrophobic. and the bottom salt-rich phase more hydrophilic. The partition of dispersed? particles is dependent on the interfacial interaction between the particles and the conjugate aqueous biphase solutions. In particular, the hydrophilic/hydrophobic properties of the surface determine the transfer of the dispersed particles into either the top (more hydrophilic) phase or the bottom (more hydrophobic) phase. Accordingly, differences in the surface chemistry of particles can be exploited to achieve selective separations. In this work, several approaches to separation control will be discussed. using pyrite (FeS2), alumina (AI203). hematite (Fe203), silica (Si02), and titania (Ti02) as model particulate materials. For metal sulfides, pH and redox potential can be used to alter the hydrophobicity/hydrophilicity of the particles. In ?the case of oxides. polymer adsorption and collector adsorption may be exploited to facilitate particle transfer.

Jan 1, 1999

By George E. Cook, Peter C. Levick, Francis M. Wells

"Relationships are established between the peak current of a pulsed, rectangular current waveform and the pulse current duty cycle under conditions of constant arc power. By appropriate choice of these interrelated parameters, it is shown that the arc pressure may be varied over a wide range even though the arc power is held constant. The methodology is suggested as a means of countering the effect of gravity in 5-G welding, while maintaining constant heat input to the weld. Combined with appropriate penetration sensors, the methodology is additionally suggested as a means of controlling penetration. IntroductionBoth low frequency pulsation (typically 0.1 - 20 Hz) and high frequency pulsation (> 100 Hz) are often used with GTA welding. Benefits derived from pulsing include improved weld quality and better process control.Advantages cited for low frequency pulsation include claims that the total heat input to the weld is reduced, the weld bead size is reduced, weld penetration is increased, grain size is reduced, porosity is reduced, weld distortion is reduced, thinner materials can be welded successfully, and the tolerance of the welding process to material and production variations is improved (1-16). With respect to the latter, pulsing aids control of weld bead penetration by increasing the tolerance to component dimensions and joint fit-up. It also reduces the sensitivity to disparities in heat sink, and it helps to reduce distortion in thin section material or distortion attributable to poor clamping. In certain materials it can reduce the sensitivity to surface oxides and to cast to cast compositional variations (16). Low frequency pulsation is also useful in welding thick materials mated by a prepared groove. In these applications the low frequency pulsation is used to obtain proper sidewall fusion as the tungsten electrode is weaved from one side of the groove to the other. In this case the weld current pulsation is synchronized with the cross seam weave pattern, such that the high current pulses occur at each sidewall. This type of low frequency pulsation has proven particularly useful in welding with narrow width groove designs (17-21). Finally, Ecer (22) has shown that the pulsed current arc is more stable against magnetic disturbances than an equivalent constant current arc."

Jan 1, 1986

By Luciano B. Oliveira, Luis G. C. Marques, Sergio N. Monteiro, Marcos V. M. Fagundes

"Biodiesel production is normally associated with large plantations of oily vegetables such as soybean and colza, in large rural areas. However, in the municipal limits of the city of Rio de Janeiro, southeast of Brazil, biodiesel is being produced from wastes commonly generated by typical urban activities such as sewage sludge, discarded fat from meat markets and post-used cooking oils. In the present work, the experience of producing biodiesel from urban wastes in Rio de Janeiro is assessed. The type of precursor materials, equipments and logistics are presented. The environmental and economical advantages as well as the drawbacks are discussed.IntroductionThe interest for a liquid fuel that could substitute those obtained from petroleum started more than one hundred years ago when Rudolph Diesel tested his no-spark internal combustion engine, impelled by compression, with peanut oil. By that time, petroleum was beginning to be extracted in large scale and no one was concerned with the future environmental problems and its eventual depletion. In the last century, the successful association of petroleum based fuels with the automotive industry was an almost insurmountable obstacle to any attempt to use nonmineral oils [1]. In addition to the greater efficiency and, by then, lower price of the diesel from petroleum, the use of plain vegetable oils introduced undesirable carbon deposits and reduced the engine lifetime. Today, the situation is reverse. The continuous increase in the price of petroleum and, above all, its contribution to climate changes are strongly motivating the use of biofuels to replace those obtained from fossil fuels such as petroleum, natural gas and coal [2].In the case of the common petroleum derived diesel, many countries are now engaged in large scale substitution programs. The USA should produce more than 700 million litters of biodiesel, while the European Community is expected too produce around 6.5 billion litters in 2008. In Brazil, the federal biodiesel program imposed a minimum of 2% addition to the common diesel. This would demand a production of 800 million litters in 2008 [3]. The Brazilian biodiesel is made from a diversified source of vegetables mainly castor bean, African palm and soybean. The main producers are agrobusiness firms located in large rural areas of the Brazilian hinterland [4]."

Jan 1, 2008

By Muhammad Abid, Kh. .. S. Karimov

"In this study, design and investigation of biogas digester consisting of methane tank with built-in solar collector to utilize solar energy for the heating of the slurry prepared from the dung and heat exchanger is designed, developed and tested. The digester was laboratory type and consists of cylindrical metallic tank of size of 0.5 m in diameter; 1 m in height and 200 liters in volume. The surface of the digester from outside was covered by thermo insulated material a glass wool, except of south side (in northern hemisphere). This side played the role of built-in collector and was blackened to increase absorption of solar irradiation and covered under 45o by glass. In the blackened side of the digester on the different heights it was installed metallic pipes for the inlet and outlet of the air, connected with heat exchanger installed inside of the digester. The heat exchanger was fixed in the level above of the inlet pipe. The horizontal plane reflector concentrates solar beams to blackened side of the digester. In the winter period, it was found that the retention time of this digester is shorter on 15% and produced biogas volume is larger on 20% with respect of ordinary biogas digester. This digester is used for the demonstrative purposes and as a teaching aid presently and base on the results it may be used for the construction of large volume digesters for use in the farms, especially located in the remote and mountain areas where the climate in the winter period is cold. Introduction At present many experts around the world have focused their efforts to energy crises because energy is one of the most important factors for the development of the society. It is known that consuming energy is proportional to quality or standard of life. There is a close relationship between energy consumption and the Gross National Product (GNP). It is obvious that for further development of the country additional sources of energy is required, which are cheap, safe and environmentally compatible with respect to the action on possible wastes. Utilization of renewable energy is one route to help in solving the above mentioned problems. In particular, biogas as a source of renewable energy is produced by biotechnology and used wide on residential scale [1]. The biogas was produced for the very first time in 1814 by Deivy from organic wastes. In 1900 production of biogas was started in Bombay (India) [2, 3]. Biogas consists of 55-70% methane (CH4) and around of 27-44% carbon dioxide (CO2) and less than 1% H2 and H2S. At present biogas is used widely in some countries for lighting, machines, and vehicles, generators, cooking and heating. Biogas generation is suitable for small to large scale operation and at present is realized in a number of developed and developing countries as USA, Hungary, China, India etc. Since 1990s biogas projects construction in China has developed steadily by the end of 1998, there were altogether 6.88 million household biogas digesters [4]. In Russia biogas digesters are used for processing of hard dung into biogas [5]. Over the last few years the very first biogas digesters were constructed in Tajikistan as well [6,7] and it was found that the digesters can work with sufficiently high efficiency in mountain areas as well ."

Jan 1, 2008

A strategy is presented for a relatively. "low-tech" means for decontamination of streams . containing .low concentrations of toxic metals. Metal ion solutions were . circulate through fluidized beds of activated carbon which support bio-films ?of bacteria .that naturally excrete exopolysaccharides. The attached 'biomass is shown to significantly enhance nickel, cadmium and silver extraction from dilute solutions (5- l00mg/l). By heat treating (at 300º C) the metal/biomass/carbon particles, bio-sorbed silver was subsequently fixed to the carbon surface. This approach to metal decontamination may therefore also provide a route for dispersing and fixing catalytic metal particles over an activated carbon surface.

Jan 1, 1991

By C. Coetzee

Additives are commonly used in copper electrowinning to improve cathode morphology. Polysaccharides such as guar are generally favoured as additives due to their compatibility with solvent extraction. Polyacrylamides are, however, being considered as possible alternatives. Understanding the influence of the structural chemistry of additives on electrowinning performance is critical to utilise them efficiently. This paper investigated polyacrylamide additives which are structurally different; their effects on copper electrodeposition were characterized and compared to that of guar. Electrochemical impedance spectroscopy (EIS) were used to characterize the effects of molecular weight and ionic charge of the polyacrylamides on electrodeposition. The findings were compared against results obtained with an industrially used guar product. Equivalent circuit modelling of EIS data indicated that an increase in polyacrylamide concentration and a decrease in additive molecular weight increased the overall system resistance.

By Laura Angeles, Martin Reyes, Ivan Reyes, Miguel Perez, Francisco Patiño, Mizraim Flores, Elia Palacios

Chemical and mineralogical characterization of a sulphide ore from the mining district of Zimapan, Hidalgo, Mexico, was performed in order to obtain accurate information on the composition of the ore to optimize the subsequent flotation process. A combination of techniques was used: Scanning Electron Microscopy (SEM) with Energy Dispersive Spectrometer (EDS), X-ray diffractometry (XRD), Inductively Coupled Plasma (ICP) and Fourier transform infrared spectroscopy (FTIR). The SEM mapping confirmed the presence of the elements: Ca, Si, Fe, K, S, Al, Zn, Mg and Mn. The XRD analysis suggests that the ore matrix is calcite; additional species found were wollastonite, johannsenite, and pyrite, among other impurities. The FTIR analysis performed for the aqua regia insoluble showed the presence of calcium oxide, copper oxide and silicon oxide. The results for the ICP analysis were:13.31% S, 2.55% Fe, 0.46% Zn, 0.03% Cu, 0.06% Pb, 0.07% Mn, 0.09% As, 0.01% Sb and 0.08 grton-1 Ag.

Mar 1, 2017

By E. Dendy Sloan

An overview of hydrate properties is given, with emphasis on unusual deviations from ice, the most common solid water form. Reliable sample preparation and reproduction of in situ hydrates provide the foundation for all hydrate science and engineering. Relations are given to connect the three domains in the title: (1) micro-scopic properties measured with Raman, NMR, and diffraction spectroscopy, (2) meso-scopic properties measured with single crystals, and (3) macro-scopic properties measured with pressures, temperatures, volumes, etc. A principal illustration relates micro-scopic and macro-scopic domains. Experiments provides the basis for improving statistical thermodynamics model for these compounds. To date, this model is one of the most commonly used industrial statistical thermodynamics applications, based upon the classical model of van der Waals and Platteeuw (1959). Microscopic measurements and simulations indicate model assumption improvements, resulting in the next generation of the statistical thermodynamics for improved macroscopic property prediction.

Jan 1, 2002

By P. K. N. Raghavan

This paper identifies potential technologies for Carbon dioxide abatement from the mining and metal industry with special reference to the Aluminium industry. Mine reclamation could contribute to this effort to successfully reach the greenhouse gas (GHG) emissions reduction commitments for a nation. An overview of GHG production by the mining and metal industry together with a review of principles used to set the context in which specific options for GHG reduction are described. Options for GHG reduction in the mining and metal industry include reforestation, Addition of soil amendments or neutralizing agents, CO2 capture and storage, initiatives towards energy reduction, waste heat recovery and alternative energy use. An analysis and quantification of the potential GHG reduction of potential carbon sinks and sequestration options for the mining and metal industry are provided. Cost estimates for different options are provided. The paper also identifies sources that could fund research regarding GHG reduction options. The paper concludes with recommendations.

Jan 1, 2011

Hazardous waste has often very complicated chemical compositions in a variety of physical forms and is normally processed in rotary kiln incinerators. Due to large variations in waste types and difficulties in feed characterization, the complex transport processes within the incinerator are not well understood, and the incineration process meets challenges in a smooth operation, and expects various uncertainties in the process chemistry and emission control. For better understanding of the incineration process, simulation was carried out by using Computational Fluid-dynamics (CFD) to characterize temperature and species distribution in the incinerator. In order to catch certain aspects of thermal and chemical behavior, a novel approach is proposed to represent approximately the waste streams and the subsequent combustion process. Hazardous waste in various forms from an industrial-rotary-kiln waste incinerator is firstly converted to a hydrocarbon-based virtual fuel mixture with approximately the same HIC molar ratio and calorific value. The simulation of the combustion process of the simplified hazardous waste was proceeded with a combustion model. The distribution of temperature and chemical species especially the remaining CO in the system is preliminarily investigated. Distribution of CO concentration, as a good indicator of emission level for the incineration process, could be used to evaluate the emission control. The predicted temperature distribution has been compared with available measurement data from an operating rotary kiln waste incinerator at AVR-Chieme, in the Netherlands. Reasonable agreement has been reached between the measured and predicted temperature data. In the next step, measurement of species distribution in the system is planned to further validate the combustion model.

Jan 1, 2003

Hazardous waste has often very complicated chemical compositions in a variety of physical forms and is normally processed in rotary kiln incinerators. Due to large variations in waste types and difficulties in feed characterization, the complex transport processes within the incinerator are not well understood, and the incineration process meets challenges in a smooth operation, and expects various uncertainties in the process chemistry and emission control. For better understanding of the incineration process, simulation was carried out by using Computational Fluid-dynamics (CFD) to characterize temperature and species distribution in the incinerator. In order to catch certain aspects of thermal and chemical behavior, a novel approach is proposed to represent approximately the waste streams and the subsequent combustion process. Hazardous waste in various forms from an industrial-rotary-kiln waste incinerator is firstly converted to a hydrocarbon-based virtual fuel mixture with approximately the same HIC molar ratio and calorific value. The simulation of the combustion process of the simplified hazardous waste was proceeded with a combustion model. The distribution of temperature and chemical species especially the remaining CO in the system is preliminarily investigated. Distribution of CO concentration, as a good indicator of emission level for the incineration process, could be used to evaluate the emission control. The predicted temperature distribution has been compared with available measurement data from an operating rotary kiln waste incinerator at A VR-Chieme, in the Netherlands. Reasonable agreement has been reached between the measured and predicted temperature data. [n the next step, measurement of species distribution in the system is planned to further validate the combustion model.

Jan 1, 2003

By S. P. Song

A computational methodology based on the coupled finite element and boundary methods is developed to predict the free surface shapes of electrically conducting liquids supported by the electromagnetic field. The work is an extension of our previous FEIBE model for induction calculations. The free surface algorithm is developed using the Weighted Residual Method, the very same used for nonlinear finite element formulation. This allows the treatment of field computation and free surface prediction in the same manner, thus making easier the formulation of the magnetically-supported free surface problems. Like other nonlinear algorithms, the boundary/finite element free surface scheme is also iterative owing to the fact that free surface shapes are unknown a priori. But the numerical scheme is robust and efficient and is capable of handling rather complex free surface deformations. Computational algorithms will be given and are tested by comparing with other solutions whenever available. Computed results of magnetically-supported free surface shapes are presented for magnetic levitation under microgravity and floating zone refining processes under normal gravity.

Jan 1, 1996

By A. Dutta, B. Devulapalli, A. Mukhopadhyay, E. W. Grald

"Computational Fluid Dynamics (CFO) has matured over the past two decades as an analysis tool for conducting virtual experiments with significant time and cost savings. It complements and reduces physical testing. CFO has penetrated the diverse materials industry in much the same way as Computer Aided Design (CAD) did more than a decade ago. As the basic numerical algorithms used in CFO have steadily improved, so have the reliability, consistency and user-friendliness improved significantly, too. Other recent trends have also contributed to the rapid growth and widespread adoption of CFO. In this presentation, CFO applications from several materials processing industries will be presented using case studies. Emphasis will be on metals, glass and semiconductor applications.IntroductionThe term materials processing covers a diverse array of industrial applications and products today. From the continuous casting of steel, to the deposition of semiconductor materials atom by atom, to the extrusion of molten polymers, materials processing applications span an incredible range of length scale, process times, pressures, temperatures and velocities. The properties of the materials themselves, in terms of density, viscosity, thermal conductivity, etc., can be complex functions of temperature, shear rate, chemical composition and time. And the processing equipment may be very complicated in geometric shape.Computational fluid dynamics (CFD), the technique of solving the governing equations of fluid motion and other related phenomena using a computer, has enjoyed widespread and rapid growth, which started in the aerospace and automotive industries. More recently, CFD has also been successfully applied to a great many materials processing problems, in spite of the challenges described in the previous paragraph. The reasons for the growing usage of CFD in materials processing are many. Using CFD to test design options and reduce the number of physical prototypes can decrease the time and cost associated with new product and process development. CFD gives insight and provides detailed predictions of operating conditions in lieu of difficult, intrusive and often expensive experimental methods. CFD can be used as an aid to scale-up processes from lab or pilot scale to full production. Troubleshooting the performance of existing equipment is often carried out with the help of CFD. Determining how an existing piece of process equipment will operate under new conditions, or with new input ,materials, is also a common task for CFD."

Jan 1, 2004

By R. F. Hammen

Copper is one of the most widely used metals in industrial processes and is also present in most mining operations. Extraction of copper from solutions often proves difficult due to the presence of complexing agents. ChromatoChem, Inc. has developed a Solid Phase Extraction (SPE) support (HiPAC) for removal and recovery of metals from wastewater. The HiPAC SPE support employs chelating agents covalently coupled to a long linker molecule. Several solutions containing copper and complexing agents were tested including 1) copper and carbonate, pH 9.8, 2) mixed metals and anions with copper and cyanide, pH 11, and 3) copper and the chelating agent EDTA, pH 11. The copper was extracted from solutions one and two at high pH, but the EDTA containing solution needed the pH lowered to make the copper available for capture. In each example, the copper concentration was significantly reduced by HiPAC SPE treatment.

Jan 1, 1994

By David B. George

Kennecott Utah Copper adopted Outokumpu Flash Smelting and Kennecott-Outokumpu Flash Converting in 1995, a process based on granulating high grade copper matte. While nickel mattes and very small quantities of copper matte had been commercially granulated for years, no large scale copper matte granulation system had been built. This paper summarizes the history and benefits of copper matte granulation, the Kennecott design basis, the successful operation for over 10 years and potential problems inherent in some matte granulation approaches.

Jan 1, 2006

By Dorothée Proffit

Characterization of solids containing cyanides is carried out according to recommendations and standard guidelines. Most of these procedures are based on the analysis of leachates collected either on site or after leaching in the laboratory of samples. Unfortunately, these sole results are often insufficient to identify the source of the pollution. To provide 'a more complete characterization of polluted solids, optical and electron microscopy, XRD, Mossbauer spectroscopy, and transmission infrared spectroscopy were combined to analyze leachates and raw or ground samples. This combination of techniques allows the determination of the kind of cyanoferrate complexes are present in the solid state, different from insoluble Prussian Blue, since they do not have the same extraction' behavior. The use of all these techniques to characterize solid samples combined ,to the usual analysis of solutions gives a better understanding of ' the cyanide behavior.

Jan 1, 1998

By I. Gaballah

Decontamination of synthetic solutions of copper acetate, chloride, nitrate and sulfate containing 10, 100 and 1000 ppm of copper, using chemically treated barks has been studied. Metal percent removal from solutions depends on the pH and the initial concentration and to some extent on the salt used. It varies from 40 to 99 % of the solution initial metallic ion's content. The maximum retention capacity of the treated bark varies from 31 to 43 mg of Cu per gram of dry modified bark. Bark loaded with copper had been analysed by Scanning Electron Microscopy and lnfra Red spectroscopy. Cu is uniformally distributed in the bulk of the bark. No copper segregation is observed. It seems that copper is bound to the acidic sites of the bark. Anions are not detected on the copper loaded bark neither with the SEM or with the IR spectroscopy.

Jan 1, 1993