Search Documents

By Richard D. Short

The Pseudo Static Pile Load Test, PLT, is a rapid method for determining pile capacity. Pile design is usually based on theoretical calculations of ultimate load capacity using soil data from a field investigation. The pile capacity is confirmed during construction by analysis of blow counts using dynamic formulae, dynamic pile monitoring, and load testing. Load testing is the most direct and reliable method of determining the actual capacity of a pile. Conventional load testing procedures, however, are time consuming and expensive. A typical load test requires installation of two to four reaction piles, construction of a high-capacity steel test frame, hydraulic jacks, and dial gauges, and will typically take one to three days per pile. Costs for load tests range from $10,000 to $20,000 per test. The Pile Load Test machine features a 25-tonne weight mounted on a mobile test frame. PLT load tests can be performed in a matter of minutes once the equipment has been mobilized to the site. This paper examines three test sites where the PLT test method was used and compares the results to conventional load test results and theoretical capacity calculations.

Jan 1, 2000

By Helmut Hass, Marco Ziller

"Abstract: 1 Sophia Spoortunnel Marco Ziller, Trevi S.p.A.:For the construction of 14 cross passages connecting the twin tunnels of the Sophiaspoortunnel the Artificial Ground Freezing technique was applied as temporary soil improvement. AGF by Brine and Liquid Nitrogen was implemented. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil during the freezing intervention in order to control the behaviour and the efficacy of the treatment.IntroductionThe Sophia rail tunnel is a bored tunnel with a length of 4.24 km, comprising two separate parallel tubes with an outside diameter of 9.45 m. The twin tunnels were excavated by a TBM equipped with hydroshield. Seven service shafts, approximately 30 m deep, were constructed in between the tunnels. From each shaft two cross passages were constructed connecting the shaft with both tubes, for a total of 14 cross passages.The Artificial Ground Freezing technique utilizing both the Brine and Liquid Nitrogen methods was used for temporary waterproofing and soil support to allow the excavation of the cross passages. The natural soil to be frozen was consisting in loose sand and clay under a hydrostatic pressure up to 250 kPa.For the measurement of the ground temperature. Automatic data acquisition and recording systems were installed to monitor the variation of the temperatures in the soil and at the contact with the tunnel lining. Furthermore, a comprehensive computerized system of sensors and cryogenic valves was designed and implemented in order to manage the whole Nitrogen process.Soil Main CharacteristicsThe soil stratigraphy is generally consisting in Clay (Holocene) from ground level to -15 m depth, followed by Pleistocenic Sand, from -15 to -25 m, and Clay below -25 m."

Jan 1, 2014

By Maurice Bottiau

The recent evolution of the piling market clearly shows a growing demand for screw piles with soil displacement. The recently developed Omega Screw pile ful-fill these new expectations, combining the advantages of vibration-free systems and the behaviour of a displacement pile. The paper describes recent experience and new applications with this very promissing pile. Full-scale load tests were carried out in different countries as U.K. or Sweden. A very attractive and innovative piled embankment is also described, using geogrids in order to transfer the loads from the superstructure to non-reinforced Omega-piles.

Jan 1, 1996

By Tom A. Armour

Different variations of soil nailing techniques have been used in the United States since the late 1970's. Such techniques owe their origins to French developments, which began in the early 1970's as a spin-off from European tunneling excavation support practice. The growing demands of urban infrastructure development and rehabilitation and environmental protection have created an active and expanding soil nailing market demand for earth retention and slope stabilization in the United States since its early developmental years. There is a clear need for a fundamental review of the large number of soil nailing techniques that are currently being used in the United States. Following a brief summary tracing the historical development of soil nailing and a generic classification of applications, this paper provides a review of the different recent advances in the design and construction of soil nailed systems. Discussion topics include nail design advances, permanent "top-down", structure support/underpinning, alternative face stability measures, composite systems, hollow bar and fiberglass nails and architectural reinforced concrete/shotcrete facings. Case histories will be presented to illustrate each of these advances.

Jan 1, 2003

By Michael Quadagno

Hudson River Pier 86, home of the historic USS Intrepid Aircraft Carrier and the Intrepid Sea-Air-Space Museum, is currently undergoing a $30M reconstruction. This project involves the demolition of the old timber pile supported pier and construction of a new 150 ft wide by 782 ft long concrete pier, built over the footprint of the old piles. The new pier consists of steel pipe piles, precast concrete pile caps, and a composite deck, made up of precast, prestressed concrete planks and cast-in-place concrete topping. This paper focuses on both the structural design and construction of the new pier, with emphasis on the pile foundation. Pier 86 is unique in that it is required to resist the extremely high lateral loads imposed on it by the permanently moored 898 ft long aircraft carrier during severe storms. A total of 360 steel pipe piles support the new pier. These piles, which are 24 in. in diameter and range in length from 58 ft to 175 ft, were driven down to bedrock. The piles, each having 200 ton allowable capacities, work together to resist the significantly large lateral loads exerted on the pier by the ship. The installation of the piles was unique in that all the piles, including the ?super-longs?, were fabricated to-length offsite, delivered to the site via truck and barge, and installed in one piece, eliminating the need for field splicing. The Pier 86 reconstruction will be completed within an extremely aggressive 18 month schedule, from January 2007 through June 2008. The refurbished aircraft carrier Intrepid will return home in September 2008, and the grand re-opening of the pier will be on Veteran?s Day 2008. This paper provides a case history for owners, government agencies, engineers, and construction professionals that will be faced with the challenges of designing and building new piers.

Jan 1, 2008

By R. G. Horvath

The Statnamic loading test is a new and innovative method for testing deep foundations. The test is relatively inexpensive, quick, easily mobilized, provides for direct measurement of applied load and corresponding displacement, and is capable of very high loading capacities. The long duration of the applied loading, as compared to a dynamic loading test, allows for a straightforward determination of the static behaviour of the foundation tested. A new method of analysis of the Statnamic loading test, the Equilibrium Point Method, is presented. A description is given of the pile-soil model and a demonstration of how the static load-displacement behaviour of deep foundations may be predicted from the Statnamic loading test data. The Equilibrium Point Method of analysis is applied to three types of deep foundations in soils which respond differently to fast loading rates. These case histories, from Canada and the United States, include data from static loading tests for direct comparison, and demonstrate the ability of the Equilibrium Point Method to predict static behaviour of the deep foundations.

Jan 1, 1993

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018

By Frederic Masse

With widespread acceptance in the market place, many engineers are choosing ground improvement techniques to provide suitable foundation subgrade at sites that would have traditionally required deep foundations. This paper discusses the Controlled Modulus Columns (CMC) ground improvement technique and some case histories highlighting the use of this technique for retail development sites. CMC are a sustainable and cost-effective ground improvement technology that transmit load from the foundation to a lower bearing stratum through a composite CMC/soil matrix. The CMC installation is also an attractive option from an environmental perspective because it utilizes reverse flight augers, which displace the soil laterally. This installation technique achieves two goals: it densifies the soil around the CMC, which improves load transfer into the element and avoids spoil and its disposal. Through the introduction of two cases histories, we will present the key benefits of the CMC technology. Each case history will clearly illustrate how a CMC solution can reduce the overall cost of a project when compared to a more traditional type of deep foundations. They will also show how the use of CMCs has benefits that relate to the overall sustainability of the project. While CMCs are an attractive financial and sustainable option, they have also demonstrated that the performance of the system is comparable to that of deep pile foundations. Because CMCs are a relatively new technology many potential users are not aware of its benefits. While we discuss the use of CMCs to support buildings in this paper, CMCs also have been used for a variety of other applications including foundations for tanks, mechanically stabilized earth (MSE) walls, and embankments

Jan 1, 2011

By Clyde Baker

Drilled shafts for many situations offer an economical alternative to driven piles. The Federal Highway Administration (FHWA) has spent considerable time and money in research and developing design and construction guidelines for drilled shafts. However, the full potential of the technology may not be realized because of the uncertainty of the effects of construction on the actual service behavior and the lack of either reliable quality control tests to check for or evaluate defects, or inexpensive load test procedures. Static load testing is very expensive and it is not feasible to load test each shaft on a project. Therefore, other means are necessary to confirm or evaluate the integrity of the completed drilled shaft or to determine the capacity of the completed shaft.

Jan 1, 1989

By Donald A. Bruce

Pin Piles are small diameter, bored, cast-in-place piles used to underpin structures. They were first employed over 40 years ago in Italy, and have been used in the U.S. since the late 1970's. However, it is only in the last few years that their full potential in terms of load holding capacity has been exploited: whereas 100 kip working loads typified former practice, ultimate loads approaching 700 kips have recently been recorded for Pin Piles founded in sand. In order to better understand the actual performance of these piles, fundamental research has been conducted by a consortium of industry and academia. This paper describes the advances made in the laboratory and full scale field testing programs. In particular, the extensive field tests have been conducted in a variety of materials in which different pile configurations have been cyclically tested to failure. By using this test method, the elastic performance of the piles has been examined and so the progressive interfacial debonding phenomenon has been studied. This has led to the development of the Elastic Ratio concept which is proving extremely useful in analyzing and predicting Pin Pile performance. Data are provided from the full scale Test Pile Programs conducted at Mobile, AL and Port Vancouver, WA. Given that Pin Piles are usually installed in areas of low headroom or restricted access, and through difficult, occasionally contaminated soils, the paper also describes key aspects of construction.

Jan 1, 1993

By Franz-Werner Gerressen

"The use of soil improvement to utilize areas, which are not suitable for foundation purpose, has a long tradition. Due to the increasing demand of foundation works in areas of unsuitable soils, the improvement of the existing soils becomes even more important in the future.Various applications and systems for various demands exist around the world. Either it is a “simple” improvement for settlement reduction or a more important aim as liquefaction mitigation. However, each system has its advantages, limits and needs.Furthermore to the soil improvement, using various tools, soil mixing can also be used for applications like cut off and/or retaining wall.The paper will describe some basics of various techniques and different applications of the systems all over the world where the systems provided solutions for different purposes, e.g. simple foundation or liquefaction mitigation.It will describe also the main equipment which will be needed to execute these works under the various conditionsINTRODUCTIONSoil mixing is a methodology where the soil is improved by mixing it with cement, lime or other binders in situ by using a mixing tool. This methodology can be used either as wet mixing or as dry mixing. In the more frequently used wet mixing process, usually a mixture of binder and water, maybe with additives, is injected and mixed with the soil. Depending on the type of soil and binder, by the end of the mixing process, a mortar like mixture is created which hardens during the hydration process. In the dry mixing process, the binder is directly mixed with the soil and reacts directly with the existing soil and water.Mixing tools show several versions, so that they are mixing around either a vertical or horizontal axis, mixing in a trench and maybe are jet assisted. Figure 1 shows a classification done by Bruce 2010. Depending on the technique, improvement depth of up to 80 m can be achieved."

Jan 1, 2017

By Donald A. Bruce

Various types of contemporary Deep Mixing Method (DMM) techniques have been used in the United States since 1986. Such techniques owe their origins to Japanese and Scandinavian developments, which began almost three decades ago. The growing demands of urban infrastructure development and rehabilitation have created a very active and rapidly expanding market demand in the United States especially since the early 1990s, and there is a clear need for a new and fundamental review of the surprisingly large number of DMM techniques that are being used domestically, or are available in other parts of the world. Following a summary tracing the historical development of DMM, and a generic classification of applications, the paper provides a review of each of the many different proprietary methods, which the authors have identified during preparation of an international survey funded by the Federal Highway Administration (FHWA). Data are also provided on commercial aspects of the various DMM techniques worldwide.

Jan 1, 1998

By Joram M. Amir

Even when they are cased! [ ] In bored piles, as well as in drilled shafts, and in caissons too, defects will occur! [ ]

Jan 1, 2001

By J. Hartikainen

19 papers were allocated to this session by the paper classification committee, 8 related to bored piles, 5 to continuous flight auger piles (CFA piles), 3 to slurry trenches, 2 to both bored piles and slurry trenches, one of them also dealing with root piles. There were no papers dealing with root piles only, as root filling is a different technique. One paper concerns sheet piling (Table 1). Table 1. Papers for session 1: Recent Technological Developments in Deep Foundations with Soil Excavation. [ ] Table 2. Classification of pile type in Belgium - van Impe W.F. /10/. [ ] Trends in piling Trends in piling in Central Europe were studied by van Impe for his brilliant lecture to the Finnish Civil Engineering Society. He claimed that bored piling is on the decrease and CFA pilling on the increase (Table 2). Thus the numbers of papers presented here do not conform to recent developments or trends. The papers submitted arc of course influenced largely by the fact, observable in Table 3, that bored piling is

Jan 1, 1994

By Arash Khosravifar

The seismic design of extended pile shafts for the combined effects of dynamic shaking and liquefaction-induced lateral spreading is investigated using nonlinear dynamic finite element analyses (NDA). Results of NDA parameter studies are used to illustrate how inertia and lateral spreading loads combine during shaking. The NDA results are used to evaluate equivalent static analysis (ESA) methods. Implications for design practice are discussed.

Jan 1, 2010

By John F. Spence

Ever since opening, the M25 motorway to the west of London has carried a rapidly increasing volume of traffic. The section of M25 between the junctions with the M3 and M4 motorways, which is in the near vicinity of Heathrow airport, is the most heavily trafficked section. Piling and ground treatment was required for motorway widening works over this route, which is 7 miles long. The foundation works were undertaken next to the live motorway and beneath the flightpath for aircraft landing and taking off at the airport. The paper describes the foundation construction techniques used, and the how the methods were affected by the live motorway and the height restrictions imposed by the airport. A unique method of piled retaining wall construction is also described.

Jan 1, 2007

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By James A. Mason

The State of California has instrumented numerous buildings, bridges, and dams throughout the state with earthquake recording devices. These accelerometers are strategically placed to measure the response of the structure to a specific seismic event. This comprehensive program enlightens the field of seismic engineering after each earthquake. The Office of Strong Motion Studies, California Strong Motion Instrumentation Program, a sub-branch of the Division of Mines and Geology, provides a professional service unequalled in the world. Within hours of a local earthquake, a preliminary report with the epicenter / hypocenter, structural damage, and time history records are available to all interested parties. The included partial report in the appendix, see section 5.1, is one of the reports that C.S.M.I.P. produced after the Loma Prieta Earthquake of October 17,1989. The diagram on the cover is even of interest. This is a small portion of San Francisco. The values on the diagram are the recorded maximum horizontal ground accelerations at that location in the city. For example, the acceleration at Yerba Buena Island was 0.06g. (The "g" refers to the acceleration of gravity. Thus, a 0.06g acceleration refers to the force, F=m*a, that the structure would experience. For this case, the force would be six percent, 6 % , of the mass of the structure.) Yet, directly on the other side of the Bay Bridge, at Treasure Island, the acceleration was 0.16g. Yerba Buena Island is a natural island composed of hard granular material. Whereas, Treasure Island is a man-made island of imported filled. Here one can see the absorption / transmission difference between hard material, which interact with short seismic wavelengths, and soft cohesive material, which interact with long seismic wavelengths.

Jan 1, 1993

By Bernard Hertlein

¦ Drilled shafts resist scour seismic loads better than groups of driven piles ¦ Drilled shaft construction creates less noise and vibration than driving piles ¦ Drilled shafts permit direct observation of bearing stratum, and confirmation of location ¦ Drilled shafts are cost effective

Jan 1, 2001

By John R. Wolosick

MACROPILES are defined as ultra-high-capacity micropiles, with working loads in excess of 250 tons. The piles are typically 9-5/8 to 24 inch (244 to 610 mm) outside diameter. They are drilled and grouted in place, with either large diameter steel bars and/or steel pipe reinforcement. The piles are typically tested to twice the working load. Piles with working capacities of up to 500 tons and tested to 1000 tons have been installed. The paper discusses MACROPILE design philosophy, construction techniques, and two case histories where this innovative foundation system has been installed. Macropiles are descended from micropile technology pioneered in the early 1950s by Fernando Lizzi of Italy.

Jan 1, 2006