Search Documents

By G. G. Oberfell

THOUGH the largest volume use of natural gas has been, is. and in all probability will continue to be as a fuel for domestic and industrial heating, it has various market outlets, both as a fuel and as a raw material for the chemical industry. Natural gas is a preferred type of fuel where ease of control, fuel uniformity, and freedom from ash are of primary importance. Other industrially important uses are as a source of carbon black and as a fuel in various low-cost heating operations. Many other uses are of varying importance and new potential uses are continually being uncovered, some being of economic importance to the gas indus¬try as a whole, but most of them involve such small volumes of gas that they are only of passing interest. Since various products extracted from natural gas and recovered as by-products from petroleum refining, such as liquefied petroleum gas and fuel oil, are being utilized in many industrial and domestic heating applications, some consideration will have to be given such materials in order to present a reasonably complete story of the importance of natural gas. Some of these materials may prove to be transient competitors and will not be available when more profitable uses are found for them. Meanwhile, however, the potential volumes of such materials available, the current volumes being marketed, and the nature of the utilization are considered as constituting an essential part of the over-all fuel picture.

Jan 1, 1946

By Edward W. Parker

THE agreement of September, 1922, between the anthracite operators and the United Mine Workers of America, which followed the 54.5 months strike during the summer of that year, contained the following provision : The parties unite in a recommendation to Congress that legislation be forthwith enacted creating a separate anthracite coal commission with authority to investigate and report promptly on every phase of the industry and the parties hereby ask the President to request the enactment by Congress of the recommended legislation. The continuance of production after Aug. 31, 1923, shall be upon such terms as the parties may agree-upon in the light of the report of the Commission.

Jan 1, 1924

By AIME AIME

ARRANGEMENTS for the Annual Meeting of the Institute were well advanced at the end of December as the following program will show. Heretofore this has been printed separately, but its inclusion in the Annual Review issue of MINING AND METALLURGY will, it is hoped, make it more easily available for reference until the final program is issued, which will be distributed at the meeting. Added details will appear in the February issue. Last year's meeting drew a record crowd of over 2300 which should be exceeded this year. Early reservations at the headquarters hotel, the Waldorf-Astoria, or any other convenient hotel are desirable, as are prompt reservations for the Annual Dinner. No one need worry about too much speechmaking this year, for the honors will be awarded and accepted in a few words instead of a few paragraphs, in seconds rather than minutes.

Jan 1, 1939

By Neville J. Price

In order that the reader may not be misled, I feel it necessary to comment upon the title of this paper. "Laws of Rock Behavior," one may take as being part of the all-embracing "Law of Nature" and this, according to the Oxford Dictionary, relates to the principles of conduct recognized as being pleasing to God. I feel it would be presumptuous to erect a code of rock behavior on this basis, so turn to a secondary definition, namely that a "Law" is that which is intrinsically reasonable. It is extremely unlikely that any group of geologists, or workers in rock mechanics would be in complete agreement about what could be taken to be "intrinsically reasonable." Therefore, this paper does not present any deified utterances, but rather deals with a few aspects of rock behavior which I consider to be intrinsically reasonable and with which I hope the reader will concur. The mode of behavior of rocks in the Earth's crust covers the range from wholly brittle to completely ductile ; with a deformation time scale which may be measured in milliseconds, for some events such as meteoritic impact, or in millions of years for the tectonic deformation involved in mountain building. A complete survey is, of course, outside the scope of an introductory paper, so I must be both brief and selective in my treatment. Any attempt to establish the mode of rock behavior in the Earth's crust should take into account data and relationships established in laboratory experiments and correlate these with field evidence. Consequently, the first section of this paper presents a brief discussion of the experimental aspects of rock mechanics which are pertinent to the subsequent discussion.

Jan 1, 1970

By J. E. Harris

The metallic elements, beryllium, calcium, cerium, lithium, manganese, titanium, vanadium and zirconium are used in metallurgical practice in relatively small percentages for the purpose of improving the physical properties of various alloys. No important uses for any of these elements have thus far been developed either in the pure form or in alloys of which they constitute the major constituent.

Jan 1, 1935

By Henry G. Granger

I. INTRODUCTION. REPEATED failures in attempts to work gold-bearing gravels by means of suction-dredges have created the impression that this method is impracticable. The suction-dredges have failed from three special causes excessive wear and frequent breakage of pump-shell, runners and liners; inability to dredge compact gravel which would ,not. readily move towards the intake; and, most important of all, closing. of the suction-pipe by stones too large to enter it. In my opinion, all three causes of trouble may be remedied: the first, by making stronger the parts most liable to wear and breakage; the second, by means for loosening the gravel at the intake; and the third, by sufficiently... Increasing.. the diameter of the suction-pipe. In suction gold-dredges, this diameter has not usually exceeded 10 or 12 in.; whereas there are few profitable gold-fields which can bee considered dredgeable, in which stones more than' 12 in. in diameter, are-.not frequently encountered. II. AN EFFECTIVE SUCTION-DREDGE. In harbor-operations, much larger stones are handled by suction-dredges.., The large dredge of the Henry Steers Contracting Co. worked for nearly four years at League Island, Philadelphia, where it sucked up, passed through the pump, and forced through 3,700 ft. of discharge-pipe; gravel containing boulders up to 200 lb. in weight. This was done with no bad breaks and few shut-downs. The cutter; and liners were the only parts liable to damage, and these were easily replaced with brief interruption of work. The chrome-steel liners are said to have lasted from six to nine months. I am informed that this dredge worked continously for nine

Apr 1, 1909

By George F. Kunz

Jan 1, 1902

By R. S. Dean

T HE theory of hardening by heat treatment was, as usual, the most actively discussed phase of metal working theory and in spite of the fact that it is now ten years since the dispersion theory was proposed by Messrs. Merica, Waltenberg, and Scott, it still retains a dominating influence. It is being increasingly recognized. however, that in its simplest form, that is, the purely mechanical effect of very fine crystallites distributed through a groundmass, it is distinctly in- adequate. To explain the observed facts we are obliged to assume some well-defined intermediate stage between supercooled solid solution and conglomerate, however fine be the particles of the latter. This intermediate has been inferred by Gaylor and Preston to be "the rejection of the atoms of the dissolved metal from the lattice of the solid solution accompanied by the possible formation of molecules."' Perhaps this may well be designated as the formation of supersaturated solid solution. Some very definite evidence of such an inter- mediate stage has been found in the hardening of steel where it appears that the very hard martensite may be considered as a supersaturated solution of carbon in a iron. The X-ray spectrometry of drastically quenched steel shows a tetragonal lattice whose parameter changes by tempering at 100" until it coincides with the cubic lattice of iron.? The same gradual change of the tetragonal to the cubic lattice has been observed by Sekito when esamining layers on increasing depth below the surface of a quenched carbon steel.

Jan 1, 1930

By H. Foster Bain

Steel for any large structure must be imported, the Hanyang works being entirely unable to supply local demand. The United States Steel Products Co. has warehouses and small stocks at Shanghai and at normal times there are heavy importations from Europe. It is difficult to obtain any accurate index of prices, but comparison of customs valuations with Pittsburgh quotations shows angles, bars and plates to have averaged $10 gold per ton higher in China in 1914, while on galvanized and tinned plates the excess was- $38 per ton. The margin since has been greater. Previous to the war little machinery was manufactured in China. There were shipyards at Shanghai and at Hong Kong which built a small number of engines, and small foundry and repair works are found at a number of ports. Their capacity was limited and the difficulties and delays incident to transport in China so numerous that in practice every important mine has a small foundry, boiler works, and machine shop. This must be taken into account in plans for work in the country. While skilled workmen can be found it is to be noted that most of them have been trained

Jan 1, 1921

By Earle E. Schumacher, Alexander G. Souden

IN the field of physical metallurgy it is becoming increasingly difficult to keep abreast of the recent develop¬ments since the diversity of investigations is so great and the literature so voluminous. The purpose of this review is to present the more important advances in the nonferrous field during the past few years, the topics discussed being classified broadly as fundamental and practical. The former includes those studies that have done most toward developing the basic science of metals and alloys, and the latter includes technical developments and applications. With the rapid growth of the metal

Jan 1, 1938

By H. W. Gillett

MAINTENANCE of membership by the technical so¬cieties and the activity of these societies in spite of the adverse business situation have been noteworthy. This forcibly brings home the fact that industry recognizes that sound technical guidance is well worth its cost. The numerous difficulties and losses due to defects of various kinds arising from gas-metal reactions are now generally recognized and interest in these problems is widespread. The forthcoming A. I. M. E. round-table discussion of gas-metal problems will do much to clarify the situation and will permit us to assay our present knowledge and to suggest the proper direction for profitable future research. "The Age Hardening of Metal" was the title of the annual I. M. D. lecture delivered by Dr. Paul D. Merica. A critical review of the known facts relating to age-hardening phenomena was first given, followed by the presentation of a theory correlating the detailed observations which have been made regarding the mechanism of the hardening.

Jan 1, 1933

Jan 1, 1965

By Linney, Robert J.

REPUBLIC Steel Corporation's iron-ore properties in the Adirondacks consist of mines, mills, and sintering plants in the Mineville and Port Henry area and at Lyon Mountain. This article will deal with the properties in the vicinity of Mineville and Port Henry. In 1938, when Republic leased the Mineville- Port Henry operations from the Witherbee Sherman Corp., these properties had just come through some hard depression years. As a result, the mine development program was far behind schedule; most of the equipment needed replacement; and above all, the entire system of mining had to be completely changed to reduce operating costs. The concentrator had been in operation for many years; the process was dry and dusty. Machinery and equipment were either badly worn or entirely obsolete. The sintering plant, also long in operation, was badly in need of repairs.

Jan 1, 1943

By AIME AIME

IF the observation of our British friends is true that Americans put new records in bigness above everything else then the 150th meeting of the Institute was not the grand success it seemed to be. Just why the attendance slumped a little this year is anyone's guess, but the favourite explanation seemed to be that half the country is planning to come to the New York World's Fair this summer and that two trips from the hinterland to the me- tropolis, with another to San Francisco of course, can hardly be justified with the present condition of the stock market and the prices of the products of our mines. Certainly, some were pre- vented from coming too by the epidemic of respiratory afflictions that was rampant in February. Unfortunately. several succumbed after they had reached New York.

Jan 1, 1939

By Alfred H. Bell

IN 1945, Illinois produced 75,210,000 bid. of oil, or 4.4 percent of the total for the United States, and ranked sixth in the nation in oil production for the third consecutive year. Production decreased about 3 per cent from that of 1944, when the total Illinois production was 77,413,000 bbl. This is the smallest percentage of decrease in production in the state for any year since a peak was reached in 1940. Daily average production for 1945 was approximately 206,000 bbl. Daily averages by months were as follows:

Jan 1, 1946

By R. T. Keyes, R. B. Clay, L. L. Udy, V. O. Cook, M. A. Cook

Based on compressibility and stress wave velocity in rock, initial explosive loading conditions, the thermochemistry of the explosive and reasonable description of the pressure-distance relations behind the shock front, the distribution of energy between the products of detonation and the burden are estimated as a function of time for various loading conditions. These include 'powder factor', loading density A (fraction of borehole occupied by explosive), and the explosive itself. Factors responsible for rock fragmentation are discussed in terms of: 1) 'release wave fracturing', 2) 'shear wave fracturing', and 3) 'release of loading fracturing' or 'rock bursting'. Release wave fracturing appears to occur only in the immediate vicinity of free faces, and shear wave fracturing only adjacent to the borehole under normal blasting conditions. Rock bursting is thus considered to be the most important means of rock fracturing in blasting. Means for maximizing it are considered. The most important factors to consider include maximum available energy A, explosive density p1, loading density A and 'powder factor'. Maximum efficiency is attained in general by maximizing the A . p1 product. This is achieved by using high density explosives at a loading density of unity (A = 1.0). Ways for achieving this condition are discussed. The bulk-handled aluminized slurry blasting agents have the desired properties for achieving optimum conditions for high blasting efficiency based on the theory outlined herein. Factors considered most important in the blasting of rock are: 1) The maximum available energy A, determined by the heat of explosion Q and the mechanical efficiency ?, a factor intimately associated with the mode of application (A = Q at highest gas concentrations). 2) The 'borehole pressure', pb, or the maximum pressure developed in the borehole after passage of the detonation wave and before the burden has had time to move or become compressed appreciably. (Owing to the short duration of the detonation wave at any particular point in the borehole, the fact that the explosive may not always fill the borehole completely and the further fact that the burden may not actually see the detonation pressure, the borehole pressure is considered more significant than the detonation pressure p2 as a performance factor in borehole blasting.) The borehole pressure is determined by the explosion or adiabatic pressure, p3 , and the loading density, A, or the fraction of the borehole filled by explosive. 3) The physical conditions important in the application of the explosive are: a) The 'powder factor,' (We/Wr), or the ratio of the wt of the explosive to that of the rock being blasted expressed as lb per ton or more generally in lb/cu yd. b) The bulk density, p1 ?. c) The 'burden' or 'line of least resistance,' the spacing between boreholes, the geometry of the borehole pattern and sequence of firing. d) The physical and chemical properties of the rock, most significant of which are possible heterogeneties, such as faulting, prefracture, and greater than micro-scale chemical heterogeneities. (This factor is not considered here but deserves a great deal of careful consideration.) All of these factors need to be carefully considered in the most economical engineering of a blast. Here is considered firstly an outline of the present status of dynamic rock mechanics, particularly as it pertains to blasting. The factors pertaining to the most efficient application of blasting agents are also considered, followed by a discussion of methods of application to achieve optimum explosives performance. ROCK MECHANICS Dynamic rock mechanics is currently a rapidly developing science contributing greatly to a better understanding and consequently the more effective application of explosives in blasting of rock.1-22 Basic to the development of the science of dynamic rock mechanics were the advances of Goransen23 and the Los Alamos and NOL groups24-28 concerning rock and stress wave phenomena and the transmission and reflection characteristics of stress waves at interfaces between different media. Basing considerations on this new knowledge as well as new experimental methods of study (ultra-high speed streak and framing cameras and electronic timers) the theory of fracture and failure of solids under impulsive loading by stress waves developed rapidly.14,16,27-29 Also the

Jan 1, 1967

By Robert S. Archer

THE proper material of construction for a given purpose is that material which meets the requirements satisfactorily at the lowest ultirnatc cost. It is consistent with this principle that most aluminum castings are made of an alloy containing about 8 per cent. copper. This alloy possesses mechanical properties satisfactory for general engineering purposes together with manufacturing characteristics leading to the production of finished castings at low cost. It is to the aluminum industry what gray iron is to the iron and steel industry. Just as some services require "semi-steel," malleable castings or steel castings instead of gray iron, there is a certain and growing demand for aluminum castings of superior strength or ductility, or both. Since the beginning of .the industry producers and others have sought to develop alloys or processes by which such castings could be made. Out of these efforts have emerged many alloy compositions and special processes, of which only a few have had sufficient merit to survive. It is the purpose of this paper to describe those which seem to the authors to offer the greatest promise for the production on a commercial scale of aluminum castings of superior mechanical properties, with special reference to heat-treated castings. The suitability of an alloy or process for actual manufacture is affected by so many factors that the problem of appraisal is not a simple one. Since this is such an important part of the whole subject it is proposed to discuss briefly some of the requirements. The final verdict is of course the result of commercial trial and experience. It will therefore, perhaps, be profitable to employ a somewhat historical method of treatment in discussing the subject of alloy development. The alloys or processes to be used in the production of aluminum castings are to be considered from the standpoint of their effects on both the utility and the cost of the finished casting. Specific gravity and mechanical properties come under the first head, while the properties

Jan 1, 1927

[Separates of all the Pamphlets published within the last three years (starting with No. 1469) are available, with few exceptions, at Institute headquarters. Separates of all the Technical Publications are also available. All the papers are on file in public, university and technical libraries, and when so indicated in the list, may be found either in the TRANSACTIONS or in the special volumes issued by the Institute.] METAL MINING TRANS. PAMPHLET VOLUME NUMBER TITLE AUTHOR MEETING AND PAGE* -1033 Relation of Air Pressure to Drilling H. W. Seamon New York 66,743, 766 Speeds of Hammer Drills Feb., 1921 1034 Time Factor in Depletion of Mines J. W. Roberts New York - 66,711 Feb., 1921 1 1035 Calculation of Ore Tonnage and Grade J. E. Harding New York 66, 117, 122 from Drill-hole Samples- Feb., 1921 1038 Discussion of Papers Presented in 1920 1041 Run-off and Mine Drainage - H. N. Eavenson New York 66, 624, 630 Feb., 1921 1043 The Health of the Underground Worker A. J. Lanza New York Feb., 1921 1045 Dust-ventilation Studies in Metal D. Harrington New York 66, 272, 282 Mines Feb., 1921 1046 Discussion of Papers Presented at New York Meeting, 1921 1072 Breakage and Heat Treatment of Rock- B. F. Tillson New York 66,758 drill Steel Feb., 1921 1073 Discussion of Papers Presented at New York Meeting, 1921 1076-M Analysis of Some Drill-steel Tests F. B. Foley New York - 66,789 Feb., 1921 1077-M Application of Magnetic Analysis to C_ W. Burrows New York 66,796 Root Drills Feb., 1921 1078-M Heat Treatment of Rock-drill Steel G. H. Gilman New York 66,779 Feb., 1921 1080 What is the Ideal Drill Steel? F. H. Kingdon New York 66,807 Feb., 1921 1081 Rock Drill Steels, etc. W. T. Ober New York 66,814 Feb., 1921 1082-C Underground Mine Development, Its J. B. Dilworth Wilkes-Barre 66, 715, 721 Definition and Valuation Sept., 1921 1084 Drill Steel from Hollow Ingots P. A. E. Armstrong New York 66,809 Feb., 1921 1088 Authors' Replies to Recent Discussion 1092 Heat Treatment of Rock Drill Steel A. E. Perkins New York 66,811 Feb., 1921 1096-M Octagonal Ventilation Shaft of Davis- J. L. Bruce Wilkes-Barre 66, 252, 268 Daly Copper Co. Sept., 1921 1100-C Determination of Electrical Equip- G. Bright Wilkes-Barre 66, 580, 605 ment for a Mine Hoist Sept., 1921

Jan 1, 1926

By S. Warren Hobbs

The section of the Northwestern United States that includes the northern Rocky Mountains and adjacent areas to the west and east is one of large mineral production and important mineral potential. The metallic ore deposits vary widely in age and type and their geologic settings are similarly diverse. A brief resume of the region's physiographic characteristics and geology sets the framework for the selected ore districts that are described in following papers and makes it possible to place these ore deposits in their proper reference to space and time.

Jan 1, 1968

By R. D. Rubright, Owen J. Hart

In the Bingham district over a span of more than 90 years, 43,947,104 tons of "non-porphyry" copper, lead, zinc, gold, and silver ore have been mined from a folded and faulted alternating series of Pennsylvanian and Permian limestones and sandstones and from some Tertiary intrusives. This ore came from six major mine areas located east, south, and west of the Bingham stock, site of Kennecott's porphyry copper deposit. The sediments were affected by varying degrees and types of metamorphism within 2000 feet or more of the Bingham stock. The intrusives consisting of the mineralized Bingham and the unmineralized Last Chance stocks and numerous dikes and sills of granite and monzonite were intruded into the asymmetrical northwest-trending and plunging Bingham syncline. Extrusives, although present, contain no ore. The bulk of the non-porphyry ore in the district was found above the Midas thrust. The primary ores are found in three major types of deposits: concordant bedding fissures, crosscutting fissures, and replacement deposits. These deposits consist of both copper and lead-zinc ore bodies that contain various amounts of gold and silver. These are in places roughly zoned both laterally and vertically and have been mined for up to 10,000 feet outward from the center of the Bingham stock and up to 5000 feet vertically below the surface. Secondary ore was of minor importance and was found in and under the oxidized zone at shallow depths. Genetically the Bingham stock, the ores, and related phenomena have had a common source.

Jan 1, 1968