Search Documents

By S. McAlister

This paper outlines the development of the Falcon enhanced gravity separator. Design objectives included continuous operation with sharp separations, mechanical simplicity, minimization of process water demand, the ability to apply a centrifugal field up to 300G's, unit capacity in excess of 100 t/h within a footprint of 10 square meters, a capital cost below $US 4,000 per t/h capacity, and total operating costs of less than $US 0.40 per tonne. A parallel development has been inexpensive, effective, semi-continuous equipment for recovery of precious metals in the free metallic state. These objectives have been largely met. There are significant opportunities for the technology in many mineral processing applications.

Jan 1, 1998

By J. M. Mutmansky, R. A. Jankowski, M. A. K. Mohamed

"SYNOPSISKnown health hazards associated with the breathing of respirable dusts, particularly silica dust, during mining are becoming a great concern in many parts of the world. The search for effective and low cost dust control methods for underdeveloped countries will help in improving the productivity and keeping the mine environment safe. This article addresses the problem by providing suggestions concerning the easiest and most cost effective methods to control respirable dust in mining and mineral processing operations. INTRODUCTIONMedical BackgroundLung diseases caused by dust in mining operations have been recognized by mankind since the time of the Roman Empire. The writings of Pliny the Younger on natural history reported on maladies associated with dust in mining in the first century AD. However, no significant advances in controlling the lung diseases of miners came about for many centuries. The effects of mineral dusts were further described by Georgius Agricola in his sixteenth century book on mining (Agricola, 1556). After the appearance of Agricola""s book, lung diseases were more readily recognized, but the nature and severity of the ailments associated with mineral dusts could not be readily interpreted.In 1896, the discovery of x-rays by Roentgen advanced the diagnosis of lung diseases and the knowledge of what causes these diseases. In addition, the discovery allowed medical personnel some method of judging the extent and severity of the lung diseases in human beings. During the ensuing years, the term 'pneumoconiosis' became the common term to describe any of the diseases of the lung in which dust particles deposited in the lungs caused fibrous tissue and loss of some of the respiratory function. However, little in the way of social remedies for the diseases resulted until much later. Society was still not ready to act decisively to reduce the causes of lung disease due to the dusty conditions in the work place.Social action against lung diseases did not occur in the United States (US) until the 1930s. At that time, a tunnel driven through a sandstone mountain near Gauley Bridge. West Virginia, caused the death of several hundred workers due to acute silicosis, a severe form of pneumoconiosis caused by silica (Seaton, 1975). Dust conditions in this tunnel were quite bad, causing many of the workers to be subjected to extremely high silica dust concentrations. The severity of the disease in many of the workers became known to the public and prompted the US Congress and many of the states to enact laws to reduce the dust levels."

Jan 1, 1998

By R. J. C. MacDonald

"The first recorded discovery of placer gold in Canada was on the Chaudiere River in Quebec's eastern townships in 1832 and the first major production came from placer deposits in British Columbia in 1858 (Verity 1974). Placer deposits were the major source of gold until the late 1890's, although lode deposits were found in Nova Scotia in 1862. In 1896 the Klondike Gold Rush commenced with the discovery of gold by Henderson and Carmack in the Yukon. The peak was reached in 1900 when over one million ounces of gold valued at approximately $22.3 million were recovered. With the exhaustion of the easily accessible deposits, more capital intensive operations were necessary such as those initiated in 1906 by the Yukon Gold Corporation. This giant dredging operation continued to produce until 1966. Today only a few small operations remain.The development of Canadian lode gold mining began in earnest around 1900 when the railroads were opening up the interior and western part of the country. At this time many discoveries occurred, particularly where mineral outcroppings were near surface. Tremendous impetus for exploration and the reopening of former producers followed the elimination of the gold standard by Great Britain around 1931, and more importantly the United States in 1933, with subsequent stabilization of the price of gold at $35 per ounce in 1934. Prior to this the price of gold was basically unchanged since 1717, approximately, $20 per ounce (Verity, 1974; Green, 1973).The depression of the 1930s adversely affected most industries, however for the gold producers it was a very profitable time. Prices of materials and equipment declined and labour was cheap and plentiful. Interest in gold mining was further stimulated in 1936 when a three year tax exemption was declared for all new metal mines. In 1938 a decline in the value of the Canadian dollar relative to the U.S. dollar benefitted the industry. The second world war provided yet again further incentive for gold production and in 1941 Canadian gold production reached a high of approximately 5.4 million ounces. This figure was not surpassed until 1991 when approximately 5.6 million ounces were produced (Natural Resources Canada, 1996 )."

Jan 1, 1998

By Larry M. Southwick

Steel mill electric arc furnace dust is a RCRA listed hazardous waste and its treatment and/or disposal are regulated by a complex set of rules. These regulations were originally established to encourage recovery and recycling of valuable components. For EAF dust, the more valuable constituents include zinc, lead, cadmium and iron. In fact, current trends are in the opposite direction, as the regulations have complicated the ability to commercialize new treatment technologies and created substantial roadblocks and liabilities for processors. As a result, almost half of the EAF dust generated in 1997 will be landfilled. The problems are compounded by difficult processing requirements, less than sterling examples of technology development and mechanical and operating problems. This paper explores some options to simplify the processing requirements and thereby easing difficulties in commercializing new technologies and expediting the recycling of recovered metals. Dust processing usually includes a simple step followed by two complicated steps. The simple step is fuming of heavy metals away from iron and other residues. The complex steps are (1) separating and purifying the heavy metals and (2) upgrading the iron residue. The first complex step can be simplified by producing an intermediate product that is amenable to processing by zinc refiners. This route benefits from the currently underutilized (by dust processors) resource offered by refiners, who have experience in and existing processes for separation and purification of zinc-based heavy metals. Various processes and their associated product options are reviewed and compared. Future directions for dust processing developments are suggested.

Jan 1, 1998

By James L. Whitlock

Biological treatment of mining and industrial effluents reached full scale commercialization around 1980. These proven, low cost, technologies have been limited in application due to a number of factors, including extended periods of time and cost required for pilot testing as compared to chemical treatment technologies, lack of biological expertise in metallurgical personnel, longer treatment periods in some cases, and performance failures based on improper application. Renewed interest in biological treatment technologies is being driven by permits with lower effluent concentration criteria, permits with bioassay evaluation, the need to remove thiocyanate, nitrates, sulfates and? other parameters. Chemical treatment processes, in general, have not been able to meet these present requirements, or require elaborate? combinations of processes, in terms of effluent quality and treatment economics. This paper addresses biologieal treatment of mining and industrial waste waters and selected recent advances in these technologies. The future looks very bright for application of these low capital and operating cost technologies,

Jan 1, 1998

By E. Fockedey

he destruction of free cyanide on a Co3O4 doped carbon felt was studied. The experiments were done with an eiectrochemical filter press cell on dilute alkaline solutions containing 250 mg/l NaCN. No chloride ions were added to the solutions. The cobalt oxide protects the felt against corrosion and has a catalytic effect on the degradation of the cyanide. This kind of electrode allows working with current density as high as 1200 Aim without any visible degradation of the felt. The most interesting results were obtained with a current density of 400 Aim' at which the cyanide concentration can be lowered to 5 mg/l with a current efficiency of more than 70 % and a specific energy consumption of about 10 kWh/ kg CN.

Jan 1, 1998

By R M. Smart, A T. Harrison

Backfill systems using unconventional cementitious binders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings æstableÆ slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 m high and the tailings were relatively high in pyrite. A GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shrinkage). The system used a slurry, but the addition of the activator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: stoping widths (mining heights) above 1.6 m; and shaft pillar removals in seismically active areas at the end of the life of the shafts. This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems). the acceleration (normally g, 9.81m/sec2) is increased to a significantly larger (but generally unmeasured and unknown) value, as shown in Figure 1.

Jan 1, 1998

By E. Allain

Extraction of basic metals from sulfides by conventional pyrometallurgical processing leads to the emission of SO2. To avoid this inconvenient, low temperature selective chlorination of sulfide concentrates could be an alternative. However, such process generates hazardous chlorides SxCly. A part of sulfur chlorides such as SCI2 can be recycled as a chlorinating agent of metal sulfides. Hydrolysis of sulfur chlorides, using a solution containing Na2S.9H2O, led to the recovery of more than 90 pct of elemental sulfur. Reduction of SxCly by hydrogen was investigated between 300 °C and 800 °C. About 70 and 90 pct of elemental sulfur were recovered from SC12 and S2C12, respectively. A flow sheet for the chlorination of metal sulfides and the treatment of sulfur chlorides was suggested.

Jan 1, 1998

By Courtney A. Young

Cyanide is a fast-acting, highly toxic substance but, at the same time, is deemed essential for sustaining life as well 'as our standard of living. In this manuscript, the facts about cyanide are presented beginning with a brief history and definition and ending with a discussion on cyanide alternatives. Other topics include speciation, physical characteristics, toxicity, manufacturing, cyanogenics, cyanide cycle, separation, destruction, and markets including those outside the mining industry. Emphasis, of course, is placed on gold production by leaching and how it is influenced by ore type, mineral characteristics and economics as well as its advantages and disadvantages.

Jan 1, 1998

By Tim J. A. Smith

Fundicion Refimet S.A. has operated a custom copper smelter at La Negra, near Antofagasta in northern Chile since 1993. From an initial operation based on Reverb smelting and Peirce-Smith, converting, the plant was expanded from 90 000 t/y to 160 000 t/y copper production in early 1997, by conversion to oxy-fuel smelting and use of concentrate injection on Converters. As part of this expansion a novel reverb gas cooling and cleaning system was developed and designed by Kilborn SNC-Lavalin Europe, the London, UK-based mining and metals; Office of Canada's SNC-Lavalin group. The reverb gas cooler needed to satisfy several very specific requirements including low cost, flexibility, robustness and simplicity of operation. Of particular importance was the requirement to cool and clean the ,oxy-fuel reverb gases and render them suitable for subsequent treatment in a conventional sulphuric acid plant. It was also important to avoid accretion or dust handling problems. This paper describes the key design features and subsequent successful installation, commissioning and operation of the unit.

Jan 1, 1998

By Harrison AT, Smart RM

Backfill systems using unconventional cementitious hinders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: 1. A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings 'stable' slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 in high and the tailings were relatively high in pyrite. .\ GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shnnkage). The system used a slurry, but the addition of the ;iutivator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: ò sloping widths (mining heights) above 1.6 in; and ò shaft pillar removals in seismically active areas at the end of the life of the shafts. \This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems).

Jan 1, 1998

In October 1993 it was decided to undertake the fourth phase of mining at Big Bell. This decision followed the exhaustion of open pit reserves in January 1993. Two stages of mining were proposed for the new underground mine. The initial stage would mine the remnant ore, consisting of the rib and crown pillars and lower grade ore on the hangingwall and footwall side of the old open stopes, which were mined from the 1930s to 1950s. Most of the old open stopes were backfilled with either deslimed mill tailings or development mullock, both of which were economic to recover. However, the mineable ore from this resource was difficult to evaluate. The second stage focused on mining ore outside the remnant areas and was initially proposed as a Core and Shell method under a caving hangingwall. This method has since been superseded with sublevel caving, in part due to the very high and deviatoric stress conditions encountered at Big Bell and the relatively long mining cycle required for open stoping. The problems and challenges discussed in this paper will cover the identification of remnant ore reserves, dewatering the old workings, and remnant mining.

Jan 1, 1998

By André. C. Louw

Diamond production from the reworked beach and river channel gravels along the west coasts of South Africa and Namibia is well known throughout the world, not only for the exceptional quality of the diamonds, but also for the sheer scope of the operations. To date an estimated 140 million carats have been produced from the resource worth some US$40 billion in today's money terms. It is therefore not surprising that it didn't take long before the attention turned towards the possible extension of this valuable diamond resource on similar submerged beaches in the adjacent territorial waters of South Africa and Namibia. This has proved to be a very successful move as the marine production in Namibia today constitutes 48% of that country's total diamond production. Although small scale recovery of diamonds from the sea commenced in the 1950's, the first large scale production came from the operations of the Texan entrepreneur, Sam Collins, in the 1960's. The De Beers Group, which took over Sam Collin's operations in 1969 had all the concession areas, as well as the financial and human resources to tackle the new mining frontier in the correct way by years of data gathering (ie diamond reserves and seafloor terrain studies) before commencing with large scale mining operations in the 1980's. Those who are familiar with the beach mining operations along the South African and Namibian west coasts will have appreciation for the daunting task of surgically removing the payable portion of diamond deposits from the non-payable material on the one hand, and the complex uneven fractured and gullied bed-rock floor of the deposits on the other hand. Not to mention the additional complexities of large boulders and hard calcretised diamond gravel layers (conglomerate) which are sometimes associated with the deposits. It was a natural development that the sea diamond mining operations were approached with the known information of the land operations, attempting to duplicate land mining operations in the sea, but taking cognisance of the variations of the terrain in the different areas. For instance, we encounter the following variations, and combinations, off the Namibian Coast. ? Close inshore - holocene sand cover often masks large areas of potentially diamondiferous gravels. ? In midwater areas (40m - 100m)

Jan 1, 1998

By S. R. LaBrooy, J. Avraamides

Thermal reactivation of eluted carbon is an essential part of most carbon-in-pulp gold recovery plants. The effectiveness of the reactivation procedure depends on the nature and level of contaminants adsorbed on the carbon, the efficiency of the elution and the temperature, residence time and atmosphere within the kiln. The most commonly used kilns are evaluated in terms of their operating parameters and performance. Data obtained both in the laboratory and in the field emphasize the importance of carbon feed moisture content, kiln atmosphere and carbon conditioning on the activity of the kiln product.

Jan 1, 1998

By G W. Clamp

The most traum atic event within the lUK coal industry during the last 30 years was its privatisation. Who were the relatively unknown people from RJB: white knights or robber barons? This paper highlights the strong safety and progressive engineering cultures th at existed and continues within the company. A long-term view of the business coupled with proven professionalism is amply developed. Quite dearly, to revert to private ownership is not a return to Victorian values but ‘back to the future’.

Jan 8, 1997

By P J. Borrington

Offering 1000 hour salt spray protection, the KEYCOAT 1000 coating presents no chipping, cracking or deformation when hammered or flexed through 90 degrees or more. This cost-effective metal protection system features lubrication performance equal to molybdenum disulphide and Poly Tetra Fluoro Ethylene (PTFE) grease providing complete anti-seize protection whilst aiding assembly and disassembly. In addition, the coating is impervious to acids, alkalis, solvents and attack by oils and all fuels. KEYCOAT 1000 has been exhaustively tested in three main industry sectors - automotive, heavy earthinoving vehicles and chemical - where it lias been proven to outperform conventional systems in all respects and as the film formed is less than one thousandth of an inch thick (typically 20 microns), it rarely presents the engineer with any tolerance difficulties. KEYCOAT 1000 is one of a w ide family of products which offer protection and lubrication to a wide industry base, from aerospace to food and with temperatures ranging from minus 190 C to plus 30 C.

Jan 4, 1997

By Philip L. LeHoux

"Kennecott Barneys Canyon Mining Co. is a gold heap leaching facility that has been in operation since 1989. In 1994, a flotation plant was commissioned to remove sulphide minerals from refractory sulphide ore. Tailings from the plant are mixed with oxide heap leach material in order to produce a geotechnically stable agglomerate from which the gold is leached and recovered in a conventional heap leach cyanidation process. The experience to arrive at an effective blending methodology is discussed.IntroductionAgglomeration is the practice of binding fine particles to coarser rock or other fines in order to avoid the deleterious effects of mobilizing the fines during the course of heap leaching(l-Chamberlin). Agglomeration has been considered a key component of successful operation at many heap leach sites. If the ore is of sedimentary origin and crushed, there is a high likelihood that the resulting product will contain a significant quantity of fines and a skewed gradation, that i~, a disproportionate amount of coarse and fine particles, with few in the intermediate size range. The exact methodology for determining whether the practice of agglomeration will have to be integrated into the operating scheme has been well discussed. These conditions are primarily geotechnical and geochemical. This paper will deal with the specific experiences of Kennecott Barneys Canyon Mining Company in modifying the agglomeration practices to suit evolving operational requirements."

Jan 1, 1997

By FJ. Johnson

Polymer utilization has increased steadily over the past several decades; however, their usefulness is sometimes limited by natural forces. For example, polymers tend to degrade when subjected to elevated temperatures. This degradation can release toxic fumes, create excess smoke, and aid in the spread of fire. For these reasons, many polymers are filled with various compounds which impart flame retardancy (FR) properties. These fillers do not make polymers non-combustible; rather, they increase resistance to ignition and reduce bum rate. Also, they suppress smoke generation, which is important as up to 80% of fire-related deaths are due to smoke inhalation [1]. Therefore, methods to impart flame retardancy in polymers are industrially important. The early flame retardants used in polymers were halogen-based, working on the principle of inhibiting free radical formation in the vapour phase thus impeding combustion propagation [2]. Usually these were combined with antimony compounds such as Sb203 to decrease loading, yet provide the same FR qualities. However, questions have arisen recently concerning toxicity of halogenated flame retardants. Possible release of toxic compounds (such as dioxins) upon combustion has been reported [3]. Fear of future regulations concerning halogen addition has led to the search for different FR fillers. Two of the more common replacements for halogen-based systems are alumina trihydrate (Al(OH)3 or ATH), and magnesium hydroxide (Mg(OH)2)' These systems impart flame retardancy through heat absorption and by release of water of hydration upon their decomposition. ATH has a low decomposition temperature (230°C), limiting its use to unsaturated polymers, epoxies, urethanes, and some wire and cable formulations. However, some advantages of ATH over halogenated FR are that it is relatively cheap, doesn't generate toxic gases, is non-volatile, and is impervious to moisture [2].

Jan 1, 1997

By A. Deneys

An experimental technique has been devised for studying the reaction kinetics of the reaction: ZnO + 2Fe0 = Zn(g) + Fe203, by which zinc evolution can occur from a molten slag bath in the absence of a carbonaceous reductant. When studying the reaction kinetics by heating from room temperature, solid state reactions and poorly defined melting points may obscure the starting point of the reaction. In order to eliminate this problem, an experimental technique was devised whereby two molten slags could be melted independently, and then mixed, to provide a well defined starting point from which to begin taking measurements. Two crucibles were mounted in a vertical reaction cylinder. The upper, mild steel, crucible had a bottom pouring plug which was sealed by a steel stopper rod. A fayalite mixture was contained in this crucible. The lower crucible contained an A12O3-CaO-SiO2-ZnO solution. Once the two slags had been melted, the steel stopper rod was removed from the upper crucible. The upper, reduced slag (fayalite in equilibrium with the upper steel crucible), drained into the lower crucible where the two slags were mixed by submerged argon stirring. Dip samples were taken to measure the zinc content of the final mixture as a function of time. The experimental procedure will be described, as well as results of experiments which were conducted on synthetic slags. The system investigated was similar to the lead blast furnace slag which is produced by the primary lead smelters of Missouri, USA.

Jan 1, 1997

Proposed by outstanding electrochemist and electrometallurgist Prof. Raphael Agladze (191 1- 1989), process of copper and manganese co-electrowinning was enhanced to the pre- electrowinning stages: low,temperature co-leaching of copper and manganese containing materials, and to high-temperature co-roasting of the same materials with consecutive leaching. The report presents results of experimental investigations of the processes mentioned above, as well as results of thermodynamic investigations of co-roasting processes, and co- leaching processes computer modeling.

Jan 1, 1997