Search Documents

By Thomas C. Shapiro

This is the final article in a three-part series on microcomputers and application software in the mineral industry. The first article covered microcomputer terms and concepts. The second discussed exploration and mining software. This article will examine plant, administrative, and geotechnical software. Every effort has been made to be current in the latest software developments. Rapid change, however, is a fact of life in the computer world and any omission is inadvertent. Introduction Geotechnical disciplines have received considerable attention in software programming. Calculations are repetitive and the formulas needed to solve them are not extremely complicated. These programs are ideally suited to the microcomputer and the microcomputer is ideally suited to the consulting geologist or engineer, due to its low cost and reliability. In fact, the advent of the Apple (a registered trademark of Apple Computer Inc.) and, more recently, the IBM personal computer has caused an explosion of inexpensive software programs available to the microcomputing public. Another area that has benefited from computerization, although not in the same way, has been mineral beneficiation. Here, process control for start-up or phase-down operations has been used in newer plants for some time. Programs to perform various calculations are becoming more common as micros increase in number. Tappi Journal has a section with solutions to handheld-calculator and microcomputer problems. Process Modeling Most process modeling is still done only on mainframes. One such program is called ASPEN PLUS (a registered trademark of Aspen Technology), and a one-week course is recommended so the user can best use the program. This program is available through timesharing from University Computing Co. Programs to find an optimal solution using Linear Programming (LP) have been around for some time. Also, plant process simulation has been possible using simulation programs. Both simulation and LP are expensive to program and run. Although there are LP programs available for some micros, the user must be fairly knowledgeable about how to set up the problem. This is because each problem must be set up as a unique program that typically requires custom programming. There are some programs that can handle blending of mine crudes and examine economic parameters over the life of the mine. Plant Applications Areas relating to mine and plant applications with programs available for micros are maintenance, production reporting, inventory, accounting, and personnel scheduling. Maintenance Maintenance typically requires that certain jobs be performed in a particular sequence and parts be ordered with enough lead time for maintenance to take place on time. There is, therefore, a critical sequence of tasks that must be performed or the scheduled maintenance will not take place. Two answers needed for maintenance project scheduling are: what is the lead time needed

Jan 4, 1984

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

Slime Flotation Using Ethoxylated Surfactants in Solutions of the Electrolytes

Sep 13, 2010

By L. Villa, O. Suarez, D. Arias, L. G. Corretge

The deposit comprises two vertical, lenticular bodies emplaced in the allochthonous block of a Variscan thrust. Epigenetic mineralisation occurs as replacement of carbonated volcaniclastic rocks of Cambro-Ordovician age. The dominant sulphide minerals are sphalerite and galena with minor chalcopyrite; the main non-metallic mineral is quartz and there is hydrothermal silicification, chloritisation and sericitisation. Sulphur isotope values for sphalerite and galena are heavy and reflect the fundamental relationship between delta-34S in ZnS and in PbS, suggesting isotopic equilibrium. Four sphalerite-galena pairs yield temperatures between 163 and 218 degrees C, in good agreement with the 187-207 degrees C estimated by the Ga/Ge-sphalerite geothermometer. The ore sulphide was leached by the hydrothermal solution from diagenetic pyrite in the host rocks and disseminated sphalerite and galena in Cambrian carbonates

Jun 19, 1905

By N Clarke, G R. Ballantyne, M S. Powell, P Elms, A Anyimadu

AngloGold Ashanti Ltd nominated Sunrise Dam Gold Mine as a case study via their involvement with the long-running Australian Mineral Industry Research Association (AMIRA) International P9P research program (AMIRA, 2015) . A group of researchers from the Global Comminution Collaborative (GCC) conducted a comminution circuit survey and review together with a large group of graduate metallurgists, senior metallurgists and operators. Fundamental and applied research understanding was used to identify productivity and efficiency improvements around the crushing and grinding circuits. The limitations of current scientific knowledge were identified through this process and this will allow future research to be more focussed on what is required by industry.The comminution circuit at Sunrise Dam comprises three stages of crushing followed by two stages of ball milling. The secondary crusher and primary ball mill classification were identified as the primary limitations of the circuit. The secondary crusher was found to be underperforming through overall equipment efficiency (OEE) analysis and an improved chamber design was identified by Chalmers University. This improved design will promote higher power utilisation, choke feeding and a finer crushed product for the milling circuit. The primary ball mill product is classified by a combination of a trommel, 3 sieve bends and a hydrocyclone. The combination of poor classification and coarse, competent feed led to a situation where the primary mill was overfilled with rocks, reducing grinding rate due to cushioning of impact. Size specific energy (SSE) benchmarking methodology was used to identify that a 10% increase in throughput could be achieved with improved primary classification.CITATION:Ballantyne, G R, Clarke, N, Elms, P, Anyimadu, A and Powell, M S, 2015. Application of research principles to identify process improvement at Sunrise Dam Gold Mine, in Proceedings MetPlant 2015, pp 221–229 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By AJ Rorke, JD Botes

Presplit blasting in strip mines is aimed at creating a safer wall to work under during the coaling operations. Good quality presplits are also necessary for effective throw blasting and drainage of the blast block. A less obvious but important function is full coal recovery. Optimum Colliery has been experiencing rock freezing against the presplit highwalls. The rock formed in patches along the highwall and trapped coal beneath it. The material that was &ozen comprised the rock between the back row of holes and the presplit and was often up to 3 m thick (the stand off distance between the back line and the presplit). The cozen rock formed predominantly along the bottom halfor bottom two thirds of the highwall. Along the top portion of the highwall, the presplit crack was usually well formed with visible barrels. This problem, or similar variations of it, is common on many South African strip-mine operations. Investigative work was carried out at Optimum Colliery to correct the problem. This paper presents the information and measurements that were made and discusses the solutions that have been applied to solve the problem. It was found that there were two independent causes for the tiozen material, with each contributing more or less to the frozen rock along the highwall. It was found that the presplit was not forming properly in places, especially closer to the bottom of the highwalls. The reasons and the solutions are presented. The second cause was found to be associated with reduced detonation velocity in the back line holes coupled with low confinement from long delay periods. Emulsion explosive that is sensitised with air bubbles was found to be prone to this phenomenon near the back of high-energy blasts. A change in the explosive formulation in the back-line holes, together with reduced delays in the back line, has resulted in significant improvements. The details are presented in this paper.

Jan 1, 2000

By Michel Bustamante

The occasional substandard performances of continuous flight auger in particular soil conditions have prompted the drilling rig manufacturer to improve the standard CFA in order to reduce its negative effects. A real improvement of interest was the launching of the double rotary CFA system. The promising features of the latter have incited the authors to implement an extensive experimental research on pile constructed using this type of technique but in the specific context of cohesive soils. Short-term static load tests were carried out on a total of 9 test piles of various installation techniques in order to compare the respective performances. The promising features of the double rotary CFA have incited the LCPC & Durmeyer Company to implement an extensive experimental research on this type of pile technique but in the specific context of cohesive soils and more particularly in clayey marls. After load tests completion the research has been completed by an excavation of the double rotary CFA piles. All the collected data concerning the implemented program are reported.

Jan 1, 2002

Sulphuric acid leaching at atmospheric pressure of a number of Australian nickeliferous laterites was examined in detail. The results obtained indicate that nickel can be extracted from these ores, although the conditions required to achieve about 90 per cent extraction vary widely. These differences in reactivity can be related to the types of nickel-bearing minerals present.Nickel is more readily extracted from nickel-bearing clays such as chlorite, than it is from nickel-containing goethite.The results clearly show the problems associated with the processing of complex ores such as the nickeliferous laterites, and they indicate the need for complete characterization of each deposit.

Jan 1, 1978

By William M. Dowall

The recently completed in-pit crushing and conveying project at Phelps Dodge's Morenci Mine is rated among the world's leading materials handling projects. The operation involves the crushing and transport of more than 109 kt/ d (120,000 stpd) of copper ore, using regenerative conveyors capable of providing more than 5.5 MW (7000 hp) of equivalent electrical energy. The Morenci Mine is located 330 km (200 miles) east of Phoenix, AZ. Phelps Dodge Corp. owns an 85% interest in the mine. The remaining 15% is owned by Sumitomo Metal Mining Co., Ltd. and Sumitomo Corp. Copper has been continuously produced from the Morenci district since the late 1800s. Until 1989, run-of-mine ore was transported from active mining faces to the Morenci and Metcalf concentrators by truck and rail haulage. In that year, a system of in-pit, semi-portable crushing plants and overland conveyors was commissioned. This substantially reduced truck haulage and effectively eliminated rail haulage in the pit. The system used two semi-portable, in-pit crushing stations equipped with 60/89 gyratory crushers. The crushed ore from both plants reported to the first of two overland belt conveyors, arranged in series, for transport from the pit to a coarse ore stockpile. The system was "backed-up" by existing locomotive rail haulage.

Jan 1, 1993

By Orlando Martino

This regional report covers the mineral industries of Canada and 40 countries and areas in Latin America and the Caribbean Basin. Also included is a brief description of the mineral potential of Antarctica. The Latin American region encompasses an area twice that of the United States. Latin America and Canada have a rich and diversified endowment of mineral fuels, metals, and industrial minerals. Tables 2 and 3 provide a summary view of the importance of Latin America and Canada's output of its major mineral commodities in world mineral supply in 1989 and 1990.

Jan 1, 1993

By L. A. Panek, F. D. Wang, M. C. Sun

A method of stability analysis of underground opening by the limiting equilibrium approach is presented. The Coulomb shear failure criterion is employed to find possible fracture surfaces and to evaluate the shear strengths along them. The normal stresses required for the calculation of shear strength, and the shear stresses for the calculation of total shear force along the fracture surfaces, are obtained by the finite-element method of plane-strain analysis. The factor of safety against Coulomb shear failure is calculated as the ratio of the shear strength to the shear force along a fracture surface, similar to the practice in slope stability analysis. Four shapes of openings are analyzed, with three ratios of horizontal lithostatic stress and four coefficients of internal friction. The critical fracture surfaces found by this method of analysis are consistent with the arching of roofs and slabbing of ribs commonly observed.

Jan 1, 1972

By A. Haque

The shear behaviour of infilled joints produced from ordinary gypsum plaster (gyprock) and bentonite was investigated in the laboratory under Constant Normal Stiffness (CNS) conditions. Shear tests were performed on saw-tooth profiles having Joint Roughness Coefficients (JRC) of 4.75 and 9.25 under an initial normal stress (sno) of 0.30 to 1.10 MPa, and at a normal stiffness (kn) of 8.5 kN/mm. Test data under the same sno and infill thickness to asperity height ratio (t/a) were analysed for two different sets of JRC. The peak shear stress plotted against the t/a ratio under constant sno revealed an increase in peak shear stress with the increase in JRC, up to a t/a ratio of about unity. The effect of roughness on the peak shear stress was observed to be minimal when the t/a ratio exceeded 1.40. A mathematical model for the prediction of peak shear stress due to the increased infill thickness has been developed based on a hyperbolic stress-strain relationship and energy balance principles. The model predictions are in good agreement with the laboratory observations. Le comportement de cisaillement des joints remplis produits à partir de plâtre ordinaire et de bentonite a été étudié dans le laboratoire sous des conditions de rigidité normales constantes. Des essais de cisaillement ont été réalisés sur des profils en dents de scie ayant des coefficients de rugosité des joints (CRJ) variant de 4,75 à 9,25 sous un effort normal initial (sno) de 0,30 à 1,10 MPa, et une rigidité normale (kn) de 8,5 kN/mm. Le résultat des essais conduits sous la même contrainte et épaisseur de remplissage au rapport aspérité/hauteur (t/a) ont été analysés pour deux ensembles différents de CRJ. La variation de l'effort de cisaillement maximal contre le rapport t/a sous une contrainte normale constante a indiqué une augmentation de l'effort de cisaillement maximal avec l'augmentation du CRJ, jusqu'à un rapport de t/a proche de l'unité. L'effet de la rugosité sur l'effort de cisaillement maximal a été minimal quand le rapport t/a a excédé 1,40. Un modèle mathématique pour la prévision de l'effort de cisaillement maximal dû à l'épaisseur accrue du remplissage des joints a été développé sur la base de la variation entre contraintes hyperboliques et déformation et sur des principes de bilan énergétique. Les prévisions du modèle sont en bon accord avec les observations de laboratoire. Das Scherverhalten in mit gewöhnlichem Gips und Bentonit gefüllten Klüften wurde im Labor unter Bedingungen konstanter Normalsteifheit (CNS) untersucht. Scherversuche wurden durchgefürt für Sägezahnprofile mit Werten des Fugenrauhigkeitskoeffizienten (JRC) von 4.75 und 9.25 unter Normalspannungs-werten (sno) von 0.30 bis 1.10 MPa, und bei Normalsteifheit (kn) von 8.5 kN/mm. Testresultate für gleiche Werte von sno und Verhältnis Fülldicke zu Rauhigkeit (t/a) wurden untersucht für zwei verschiedene Werte von JRC. Die Beziehung zwischen maximaler Schubspannung und und t/a Verhältnis unter konstantem sno zeigte einen Anstieg der maximalen Schubspannung mit zunehmendem JRC, bis zu einem t/a Verhältnis von etwa 1.0. Der Einfluss der Rauhigkeit auf den Maximalwert der Schubspannung war minimal solange das t/a Verhältnis den Wert von 1.40 überstieg. Ein mathematisches Modell wurde entwickelt für die Vorhersage der Schubspannung die von zusätzlicher Fülldicke erwartet werden kann, ausgehend von einer hyperbolischen Spannungs-Dehnung Beziehung und dem Energiegleichgewichts-prinzip. Die Modellvorhersagen zeigten gute Uebereinstimmung mit den Laborbeobachtungen.

Jan 1, 2003

By Paul J. Sylvester, Yeonuk Choi, Mike Nelson, Louis J. Cabri, Mike Tubrett

"The development and characterization of sulphide standards containing as many as seven precious metals has increased the efficiency and comprehensiveness of micro-analyses for deportment studies using laser ablation microprobe inductively coupled plasma mass spectrometry (LAM-ICPMS). Because trace precious metals occurring in solid solution or as sub-micron inclusions in sulphides, arsenides, and sulpharsenides are often heterogeneously distributed, a significantly large number of analyses are required. Using well-prepared samples it is possible for up to 120 analyses per day, far more than by other comparable methods. Examples will be discussed from projects focused on the deportment of Au and the platinum group elements (PGE).INTRODUCTIONBecause gold and the platinum-group elements (PGE) occur as both discrete minerals and in trace quantities in a variety of minerals (mostly sulphide, arsenide, and sulpharsenide minerals), specialized trace analytical methods were developed and applied to determine the deportment of precious metals in ore deposits, requiring sensitivities ranging originally from about hundreds to presently tens of ppb for individual precious metal or less.In mineralogical studies, micro-analytical techniques such as the electron microprobe were first applied to obtain analyses for major elements in about 1959-60, but as the instrumentation improved early attempts for PGE in potential carrier minerals indicated that reasonable levels of detection (LOD) were of the order of 300-400 ppm, depending on analytical conditions, X-ray spectral lines, and mineral matrix (e.g., Cabri and Laflamme, 1976). Eventually, the lowest detection levels by electron probe micro-analyses (EPMA) obtained for some PGE were of the order of 10s of ppm using high accelerating voltage and current for extended measuring time on peak and background (Gervilla, Cabri, Kojonen, Oberthür, Weiser, Johanson, Sie, Campbell, Teesdale and Laflamme, 2004)."

Jan 1, 2010

Compagnie Miniere Esperance (CME), a mining company based in French Guyana, operates a gold primary ore body in open pit. The ore is processed through crushing, grinding and gravity separation. Tailings are stored in a ?fine? pond. Analyses of the fine ponds proved a residual gold grade sufficient for a chemical treatment. However, direct cyanidation would require a too large installation, regarding the local conditions (accessibility, supplying and rainforest meteorological conditions). It has been then decided to test the feasibility of a pre-concentration using flotation. Lab tests have been carried out by SGS Lakefield (Canada) in March 2007, which proves the technical feasibility. Therefore, CME asked Caspeo to: ? Carry out an on-site flotation pilot campaign. ? Design an industrial flotation circuit. The tailings reprocessing will contribute to a better tailings management and a dry up of the gold resource, limiting the risk of illegal mining after remediation of the CME site. CME MINE The Esperance gold mine is located in French Guyana, in the vicinity of several gold deposits as Omaï, Rosebel or Camp Caïman, holded by Iamgold and Newmont. These main gold deposits are located on the figure 1. Esperance was put into operation in the early 90?s. The first years were devoted to the mining of alluvial gold in the gravel of the Esperance Creek. Since then, operation was led in the primary gold deposit. Annual production is on average 254kg for a total production in fifteen years of 4300kg. Geology Esperance deposit is located in the greenstone belt of the Guyana Shield. Mineralization is in tectonic contact between sedimentary basin of Maroni and a granitic massif. Clastic series, composed of conglomerate and lamina sandstone, overlie a volcano-sedimentary basement (series called "Paramaca"). The area is strongly folded by shear movements, resulting from granite deposit. Gold is in interlacing quartz veins intersecting the clastic series. Gold is present in association with pyrite. Other elements, as silver or arsenic, are in negligible quantity. Exploitation The Maroni River is the only access to the Esperance mine. Only the saprolite and a part of the transition rock are extracted in the open pit. Excavation works are done using shovels Hyundai 450 (4 units) and haulage works using articulated dumpers Terex TA35 (4 units). These two sorts of equipments are presented figure 2. Mill The mill is composed of crushing and grinding processing plants. After gravity concentration, both plants produce tailings that are stored in two ponds: the first pond contains coarse product which segregates the particles crushed to 2mm upstream and settled clays downstream; the second pond contains the fine product made of particles ground to 200µm. These two ponds, bordered by dams and diversion canals, are located on former alluvial sites of Esperance Creek (see figure 3). [ ] The CME mill is currently producing gold concentrate, with a global recovery of about 67%. The ore is crushed by one jaw crusher and two hammer crushers. The ore then passes through a Knelson KC 48 gravity concentrator, producing a first gold concentrate. The

Jan 1, 2009

By L. H. DeWald

During the examination of various commercial brands of copper wire bars, which had exhibited different degrees of adaptability for being drawn into fine gages of wire by the present-day high speed machine, it was found that each brand had a more or less characteristic crystal macrostructure. The extremes of these macrostructures are similar FIG. 1.-EFFECT OF METAL TEMPERATURE IN CASTING ON CRYSTAL MACROSTRUCTURE OF BAR. Reading from left to right, metal temperatures were 1166" C., 1149" C., 1132" C.. 1121" C., 1093" C. to the maximum variation shown in the photomacrographs reproduced in Fig. 1. As the various brands did not differ materially in chemical composition, it was concluded that the differences in structure were the result of variations in casting technique.

Jan 1, 1931

By M. Hancer, J. D. Miller

It is known from soluble salt flotation practice that the K, Mg double salts of kainite (KClMgSO43H2O), and carnallite (KClMgCl26H2O) are difficult to float and must be converted to other salts such as schoenite (K2SO4MgSO46H2O) and sylvite (KCl) in order to recover potash values. The flotation characteristics of these double salts have now been confirmed in some detail by carefully controlled laboratory experiments with both cationic and anionic collectors. The experimental results are discussed in view of recent experimental findings regarding the flotation characteristics of simple salts, in which the flotation response was shown to be determined by the interfacial water structure and whether the salt could be considered to be a water structure maker or a water structure breaker. The same approach can be use to explain the flotation response of the potassium double salts ; schoenite, kainite, and carnallite. In addition, the sign of the surface charge of schoenite (K2SO4MgSO46H2O), was determined as a function of pH from nonequilibrium electrophoretic mobility measurements. Schoenite appears to exhibit three charge reversals (CR) which can be explained based on surface hydrolysis reactions. The flotation behavior of schoenite is further considered based on solution chemistry calculations, electrophoretic mobility measurements, and microflotation results.

Jan 1, 2001

This paper is an outline of the developmental practices now in use at North Broken Hill Limited, N.S.W. The description will be given under the following headings.I. General.......opening up of a new level.II. Driving.III. Winzing.IV. Rising.V. Auxiliary Ventilation.VI. Notes on the Introduction of Mechanical Appliances.VII. Office Records and Routine.I. GENERALThe lode, for purposes of description, may be said to be divided into two portions which are usually referred to as the Southern and Northern Orebodies.The southern ore-body is the larger and in places attains a width of 200 feet. The northern ore-body is, generally speaking, comparatively narrow. These ore-bodies have a northerly pitch of approximately 45' and a westerly dip of 60. In the southern ore-body a grid of ore chutes is provided at 31 ft. 8 in. (5 square set) intervals and this necessitates an elaborate arrangement of cross-cuts, portion of which have to be driven through the foot-wall. Crushed country rock adjacent to the foot-wall makes it necessary for drives to be placed at least 60 feet from the lode.In the northern ore-body the ore chutes are arranged along a longitudinal drive, thus making a much simpler layout. These layouts were described in detail by A. R. West (Proceedings A.I.M.M. No. 117). In opening up a new level from the shaft plat, a heading is extended in a westerly direction until a point approximately 60 feet from the footwall of the lode is reached.At this point the direction of the cross-cut is altered to a bearing approximately 90 to the general strike of the ore-body, and the cross-cut continued until the hanging-wall is intersected. From the information obtained together with that from diamond drilling, the outline of the ore-body is plotted as closely as possible, and this serves as a basis for the layout of the level. Drives south and north from the main cross-cut are made in order to determine the southern and northern extremity of the southern ore-body. The former is usually driven in the centre of the ore-body and serves as a permanent gangway and ventilation drive for the new level.From the northern extremity of the southern ore-body, the drive north is...

Jan 1, 1944

By Y. Shu, A. R. Laplante

"A laboratory Knelson Concentrator (LKC), 7.5 cm in diameter, was used to study the performance of a similar unit at plant scale, 76 cm in diameter, This paper reports on sampling and assaying procedures and problems, and discusses the performance of the plant unit.The sampling procedure was based on the extraction of large samples, 5-15 kg, and their complete processing with a LKC, to characterize size-by-size performance. The procedure yielded reliable estimates of overall gold assays, after blatant assaying errors were corrected. The plant centrifugal unit concentrate was sampled in situ, which yielded very erratic grades, with a large overall negative bias. Due to the very heterogeneous nature of the concentrate, which can be linked to flow patterns in the riffles of the unit, it is recommended that for future testwork, the concentrate be recovered separately, blended and then sampled.The plant centrifugal separator, when operated at a feed rate of 25 t/h, yielded total and free gold recoveries of 41 % and 62%, respectively. This is much lower than previously reported data, and suggest that at 25 t/h, the unit is overloaded. However, recovery did not decrease with time over a loading cycle of 2 hours, which suggests that present loading cycles, generally 1 hour, can be significantly increased. INTRODUCTIONThe study of gold gravity circuits is plagued with the statistical problem of determining the behaviour of particles occurring with a very low frequency. This problem becomes particularly acute with increasing particle size. For example, considering the average weight of a gold flake in the 840-1200 µm (20/28 mesh) to be about 5 mg (Banisi et al, 1991), a reasonably high grade feed of 10 git would require, for a relative error (standard deviation) of 10% on grade, 100 particles, that is 0.5 g of gold, or 50 kg of 840-1200 µm material (a Poisson distribution is assumed). Gy's formula, for the same data, yields a weight of 33 kg, with a shape factor of 0.1 and a size distribution factor of 0.5. Both results are comparable; to obtain the suggested weight of material, a stream containing 5% weight in the 840-1200 µm would require 1 tonne samples (of unsized material). The problem rapidly disappears with decreasing particle size. Still with Banisi et al's data, a gold flake in the 300-420 µm range averages 0.5 mg in weight; the same 10% error on grade corresponds to a weight of 5 kg. Gy's formula for the same size distribution and particle shape factors as above predicts a required mass of 1.4 kg. This would correspond to an unsized sample weight of 10 kg with 14% weight in the 300-420 µm, for example."

Jan 1, 1992

By Richard K. Sandaas

Start Date: April 4, 1988 Completion Date: Dec. 29, 1989 Contractor: SCI Contractors Past and present transportation centers will come together at International District Station, located at the south entrance to the tunnel next to the turn-of-the-century Union Station train depot. The area will bustle once again with activity as commuters and visitors converge on the modern transit station at the edge of Seattle's International District. Buses coming from south Interstate 5 and Interstate 90 will enter the tunnel through this station. [ ] International District Station is an open-air station, 1,060 feet long and 82 feet wide (about 15,400 cubic yards of concrete were used to build the station). A concrete lid over the southern portion of the station staging area is held in place by 131 support piles. The station will include entrances on Jackson Street and King Street. Union Pacific Realty is planning to build an office and retail complex upon the lid. The station also has an international flair. Symbols of the Chinese zodiac will be etched into the station plaza floor. The station platform walls will be lined with large steel panels embellished with designs in origami?a Japanese folded paper art form. [ ]

Jan 1, 1990

By Ali Ameli

Design loads are limited for piles relying upon toe stresses in rock due to uncertainty about the rock quality over the whole pile diameter because of rock mass properties or construction effects. The paper discusses the use of video images to evaluate rock quality at the bottom of piles socketed into graniodorite bedrock in a steel pipe pile project. Skillful interpretation was required to assess the 3D properties of the rock from video images. It is necessary to observe the rock mass characteristics near the project site for better perception of the rock features from the images. Video image interpretation skills were established by the evaluation of the cores drilled under the socket base and the results of pile loading tests. Correlations were found between rock appearance in the images and the rock socket drilling records. Rock socket acceptance criteria were developed through monitoring the drilling operations for the specific site procedures. Video images then served as one of the quality-assurance tools together with probing and pile loading test. Lessons and methods learned from video inspection in this project could be used to evaluate rock quality in similar cases.

Jan 1, 2006