Search Documents

Wet mining of auriferous gravels at L & MÆs Waikaka operation in Southland creates spoil dumps derived from stripping of a clay rich overburden, tailings from past dredging and the processing of auriferous sands and gravels. Over recent times, spoil dumps have slumped on six occasions, threatening the viability of the wet mining operation. Close examination of slump morphology, coupled with the sequence of material placement and rate of dumping suggested a mechanism associated with undrained failure of a 2 m layer of silt and sand tails forming the base of dumps.Commencing with some information on the geotechnical properties of source overburden, back analysis of failure morphology and sequence and development of undrained loading conditions from first principals, the most likely failure mechanism and factors controlling failure were defined. Based on analysis results, a scheme to stabilise the lowwall dumps was developed and implemented, augmented by continuous monitoring of pore pressures in the basal wet tails, and laboratory testing for confirmation of computed material properties.Lowwall spoil stability has improved since implementation involving changes to the method of spoil loading, and modification of wet tails composition to improve permeability and drainage of the basal wet tails under load. The method and approach to prediction and verification of failure mechanism provide a sound basis for continued mining of deeper auriferous gravels.

Jan 1, 2002

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

By J. Z. Cui

In this paper a statistical multi-scale method for the mechanics parameter prediction of the rock mass with random distribution of multi-scale cracks/joints is presented. First the micro-structure of the rock mass with random distribution of multi-scale cracks/joints is represented. Then the statistical second-order two-scale method for the mechanics performance predictions of the rock mass structure with random cracks/joints distribution is presented, including the statistical second-order two-scale expression on the vector-valued displacement, strain tensor and stress tensor, and the algorithm procedure of statistical multi-sale computation for the mechanics parameters. Finally some numerical results for mechanical parameters for the rock mass with random distributions of multi-scale joints/cracks by statistical multi-scale method are shown.

May 1, 2009

By Travis Q. Lyday

The other South Pacific islands included in this chapter extend from Papua New Guinea, east of the Indonesian Province of Irian Jaya on the island of New Guinea, to Fiji, straddling the 180° meridian. A number of islands have been omitted from this chapter owing to the fact that their only mineral production remained insignificant to the economy of the respective country or territory. These islands include the French overseas territories of French Polynesia and Wallis and Futuna Islands; the independent states of Kiribati, Tonga, Tuvalu, and Vanuatu; the New Zealand freely associated state of the Cook Islands; and the New Zealand dependency of Niue. The mineral production that did exist in these islands was limited to construction materials such as coral reef limestone, crushed stone, and sand and gravel in minor quantities used solely for domestic consumption. FIJI Fiji, an archipelago in Melanesia consisting of 300 islands ranging from tiny coral atolls, cays, and rugged coral limestone islets to the larger mountainous, volcanic islands of Kadavu, Taveuni, Vanua Levu, and Viti Levu, straddles the 180° meridian about 1,800 kilometers south of the Equator. Fiji has been an independent member of the British Commonwealth of Nations since October 10, 1970.

Jan 1, 1988

By D Wyatt, J Domenico, W Kow

Over the past few years developments in heavy minerals processing have concentrated on the mineral separation portion of the business. The best example of this would include new developments in rare-earth magnetic separators and associated flowsheet modifications. Except for some minor modifications in spirals, the æwetÆ side of the separation business has lagged behind the ædryÆ side. Basic concentrator design has not changed in 20 years. Recent pilot trials by Outokumpu Technology have shown the benefits of a new gravity flowsheet that combines density separation and spiral concentration on a variety of heavy mineral deposits. This concept is already well utilised within the iron ore industry. The synergistic combination of these two technologies allows smaller, simpler, and controllable gravity concentrators to be built while providing equivalent or better grade and recoveries of valuable heavy mineral. This is contrasted to the all spiral flowsheet characterised by the diminishing returns of multiple stages of spirals and associated recirculating loads. Examples of the flowsheets and associated benefits will be presented from a variety of cases.

Jan 1, 2001

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 150 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey (USGS) canvass of producers. Domestic production in 2005 was estimated to be 24.8 Mt (27.3 million st) valued at $176 million. This was based on a preliminary survey of the common clay and shale industry. The leading producer states, in decreasing order by tonnage, were North Carolina, Texas, Alabama, Georgia and Ohio.

Jan 1, 2006

By E. S. Wheeler

The rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the last weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion-resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success. The successful production of castings of monel metal and nickel requires careful attention to molding practice, proper melting equipment

Jan 1, 1930

By R Hoskings

Conceptual studies of the run of mine stockpiling and reclaiming requirements commenced in 1975. Final selection of equipment was made in 1978 and the equipment was commissioned in June, 1979. Equipment selection was made after extensive investigation and visits to existing facilities throughout the world. The equipment selected is described and compared with the alternatives. Foundations were designed to minimise cleanup effort and to ensure stability of equipment under design wind loading without storm bays. Programmable logic control enables the stacking and reclaiming facility to provide a blended feed to the coal preparation plant.

Jan 1, 1980

This paper is intended partly as a summary of the conclusions that have been arrived at by various authorities on this matter, and also with a view to initiate some discussion on the subject, especially as most of the quartz gold mines in Victoria are operated without having any proper assay plans or any idea of the real values other than those given by the mining managers, who, from experience in the particular cases, are supposed to be able to arrive at a correct idea of the true values of- the ore, and, in many cases, oppose any other methods than their own, holding the view that no sampling is equal in correctness to the bulk sample of the battery. The necessity of properly sampling and estimating the ore in a mine in every case, perhaps hardly needs to be urged on the members of the Institute, but is not, apparently, so obvious to others.It is proposed to confine this paper to the sampling of ore reserves in a mine, and the various points which have to be taken into consideration in arriving at values, from the assayer's point of view, leaving the methods of sampling metallurgical products out of consideration for the present. "It is advisable to define" ore reserves" as ore exposed on three sides at least, and accessible to the sampler on all three. "Prospective ore" would include all ore not so fully exposed; but which may, from the nature of the case, and the geological conditions prevailing, be reasonably supposed to exist.

Jan 1, 1904

By Michael B. Cortie

The young field of nanotechnology has as its objective the design and construction of useful devices made of nanoscale materials. Objects or structures which have at least one important dimension in the range 0.5 to perhaps 50 nm may be considered to be in the nanoscale domain. These sizes lie far below the 200 nm or so that can be resolved with an optical microscope, and are closer in size to the 0.3 nm diameter of individual atoms. Nanotechnology, which is the study and exploitation of these tiny structures, is attracting keen interest at present. The excitement is motivated by the observation that control of matter at the nanoscale holds the promise of faster computing, better medicines, and smarter materials. In this paper, the physical phenomena on which this optimism is based are broadly discussed and explained. Where appropriate, examples of the rather different and curious properties of gold at the nanoscale are used to illustrate the points covered.

Oct 1, 2003

By B Xiao, J Yang, H Chen

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Tuwu-Yandong Cu deposit, located in the East Tianshan mountains in the eastern section of the Central Asian Orogenic Belt, is the largest and economically most important porphyry Cu deposit in Xinjiang, China. It contains ~3 Mt of copper at an average grade of 0.46 per cent Cu and 0.2 g/t Au, with significant amounts of Mo and Ag. The deposit is mainly hosted in the Carboniferous Qi’eshan Group and plagiogranite porphyry, and is controlled by faults that are east–west-, north-west- and north-east-trending. Ore minerals in the Tuwu-Yandong deposit are dominated by pyrite, chalcopyrite and molybdenite, with minor bornite, chalcocite, magnetite, sphalerite and galena. Gangue minerals are mainly composed of quartz, sericite, chlorite, epidote, anhydrite, gypsum, muscovite, biotite, phosphorite, sphene, dolomite, actinolite, barite, albite and calcite. Based on the megascopic and microscopic textural relationships and mineral assemblages, five stages of hydrothermal alteration and hypogene mineralisation are recognized in the Tuwu-Yandong Cu deposit: the potassic stage, propylitic stage, phyllic stage, late veins stage and supergene stage. Most of the copper was deposited during the phyllic stage, along with less molybdenite.CITATION:Xiao, B, Chen, H, Wang, Y and Yang, J, 2015. Geology, mineralisation and alteration of the Tuwu-Yandong porphyry Cu deposit, north-west China, in Proceedings PACRIM 2015 Congress, pp 641–644 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Lance McAnuff

The year 2001 coincided with the forty-fifth year of blasting-control specialization by the author. Commencing with the construction of the Saint Lawrence Seaway System in 1956 and continuing until the present time this career has spanned one of the most progressive and exciting periods in the still relatively short history of commercial blasting. The paper touches upon a number of the more interesting projects with which the writer was involved during those early days, including the removal by explosives of “Ripple Rock” the infamous underwater hazard to shipping which at one time inhibited ocean traffic along the Inside Passage between Vancouver Island and the mainland of British Columbia, Canada’s most westerly province. Various assignments involving incidents from devastatingly ,tragic to comically absurd are described, along with personalities encountered along the away, most of them readily recognizable as giants in the field of explosives engineering. Various stages in the evolution of state-of-the-art explosive products, initiation systems vibration monitoring equipment and limiting criteria are compared and some of the effects these have had on safety and productivity during the last forty-five years are analyzed.

Jan 1, 2002

Ledcap Pty Ltd has developed two software tools for assisting in the determination of life-of-mine (LOM) trucking requirements. The first tool generates haul paths and the second calculates truck travel time over these paths. The two step approach allows the paths to be viewed and if required edited, to better represent the actual site haul routes.The first tool automatically creates haul paths between the mine bench and the dump. To do this the user supplies a master haul route and a scheduled block model. The master haul path and the block model are interacted to create multiple haul routes, one for each pit/dump bench pair in each scheduling period. Each path carries with it a record of the scheduling period it represents and the dry tonnage hauled over the path in that period.The second tool calculates truck travel time over the path. Data from the manufacturer's rimpull and retarder curves are used to calculate accelerations and speed over each segment of the haul path. As the paths are derived from digitised representations of mine haul routes the path f les often have over a hundred segments. This detailed representation of the haul route allows the software to automatically adjust speed for different radius corners and accurately simulates the changing accelerations over the gradient changes that occur in real life mine ramps. Rolling resistance can be specified at a global level, at a segment level and at a period level. This allows rolling resistance to be changed seasonally as well as spatially.Life-of-mine trucking studies attempt to calculate an accurate answer from extremely variable inputs. This paper will detail the features of the two software tools and how the tools provided in the software can assist the mine planner to have greater confidence in their life-of-mine trucking requirements and the subsequent production capacity inputs to their scheduling calculations.

Dec 6, 2010

By V. Labiouse, B. Heidenreich

The rebound phenomenon, which occurs during rockfalls when a rock block impacts with a slope surface, is influenced by several parameters related not only to the slope material but also to the block and the kinematics. The paper presents a small-scale testing campaign undertaken at the LMR (EPFL) to better understand and quantify the bouncing of blocks on granular slopes. The influence of some factors related to the ground material, the block and the kinematics is examined. Bei Steinschlägen wird die Flugbahn eines stürzenden Felsbrockens maßgeblich durch den Abprall vom Hang bestimmt. Der Rückprall hängt von verschiedenen Parametern ab, wobei nicht nur das Hangmaterial sondern auch Blockeigenschaften und Kinematik eine große Rolle spielen. Zum besseren Verständnis dieses Phänomens und seiner Quantifizierung werden am LMR (EPFL) kleinmaßstäbliche Versuchskampagnen auf granulären Materialien durchgeführt. Der vorliegende Artikel stellt die Versuche vor und untersucht den Einfluss verschiedener Boden-, Block- und kinematischer Parameter. Le phénomène de rebond qui se présente lors de l’impact d’un bloc rocheux sur la surface d’un versant dépend non seulement des caractéristiques du terrain, mais aussi de facteurs relatifs au bloc et à la cinématique. L’article présente une campagne d’essais sur modèle réduit entreprise au LMR (EPFL) afin de mieux comprendre et quantifier l’impact de blocs sur des matériaux granulaires. L’influence de divers paramètres relatifs au sol, au bloc et à la cinématique est mise en évidence.

Jan 1, 2003

By W. U. Reimold, R. Armstrong, R. G. Charlesworth

For many years rockbursts have plagued the mining industry. Although much research has gone into studying this phenomenon only a small proportion of it has been on the actual source mechanism. A study was recently carried out to compliment the previous work done on the micro-structure of these features and to compare it to the micro-structures seen on shatter cones, from meteorite impacts. Both optical and electron-microscopy were used during the study. Samples were collected from rockburst sites by the CSIR Miningtek Rockburst Investigation Unit, and from the collar of the Vredefort Impact Crater. In the optical-microscopy study, the pinnate fractures observed in previous studies were seen in the shatter cones, through all the material. In the rockburst samples, the fractures were observed only in the quartz grains. Quartz micro-crystals were present in the rockburst samples and appeared to be the product of comminution rather than crystallisation. Cataclasite was present on rockburst and shatter cone fracture surfaces. The observations of the shatter cone surfaces with the scanning electron microscope are in agreement with previous work, including the observed presence of melt features, spherules and spheroidal material. The deformation in the rockburst samples is concentrated in the quartz grains, highly complicated with brittle features like sub-conchoidal structures and step structures present. A quartz spherule was identified on one rockburst sample and rhombic-dodecahedra type micro-crystals were present and seen fracturing off quartz grains. It is clear that the rockburst and shatter cone fracture surfaces are quite different; the shatter cone deformation is equally distributed across the sample and involves plastic-deformation, while the deformation in the rockburst material is concentrated in the quartz grains and, with the exception of spherule formation, is brittle. This study agreed with the current explanation for the formation of the rhombic-dodecahedra, and disproved the possibility of it being coesite or fine-grained meta-chert. Although there is no definite evidence of the mechanism of formation of the spherule, it is believed to be the product of vaporization and condensation, and the presence of this material indicates the extreme conditions under which this event occurred.

Jan 1, 2003

By Linda Duncan, Trevor Yeomans, Chris Potorieko, Michael Fullam

"NVI Mining’s Myra Falls Operation is a 4,000 mtpd copper/zinc flotation circuit with by product gold of ~28,000 ounces per year. Gold recovery has historically averaged 40-55%, however, a portion of this was recovered in the zinc concentrate and received poor payment. Two Knelson CD-30 Concentrators have been operating in the grinding circuit since 1992, with gravity recovery averaging about 2-5% over that time period.The Myra Falls gravity circuit was one of the very first hard rock mining installations operating in the world with automated Knelsons. The mine has employed a unique and unusual upgrading method for the Knelson concentrate that had never been evaluated as to its efficiency. Recent Gravity Recoverable Gold Testing by McGill University, and mathematical modelling of the Gravity Circuit by Knelson Gravity Solutions indicated the gravity circuit was not living up to its potential. Myra Falls Personnel changed the upgrade system-operating regime, and a complete gravity audit of the grinding circuit was carried out, with the results confirming the initial suspicions. Gravity recovery increased from 5% to 15%, with overall gold recovery improving by 5%.INTRODUCTIONNVI Mining operates a 4000 tpd mine and mill complex on Vancouver Island. The milling circuit consists of open circuit rod milling, closed circuit ball milling, gravity recovery, copper flotation, zinc flotation, and tails disposal. There are two milling circuits, “A” circuit, and “B” circuit."

Jan 1, 2006

By D G. Randall, R Jivanji, J Nathoo, T Reddy

Paradoxically, the increased emphasis on water treatment in mining has generated a new problem û hypersaline brines. Currently brines are either disposed of into ash systems, lined evaporation ponds or hazardous waste sites. Evaporative crystallisation (EC) is an alternative, but the energy requirements can be prohibitive and the salt product is still a waste that must be disposed of. Eutectic freeze crystallisation (EFC) is an alternative technology that is capable of separating aqueous solutions into pure water (as ice) and pure, solidified solutes. It is highly energy efficient and does not depend on the introduction of any solvents. In addition, the simultaneous production of pure ice and potentially saleable pure salt(s) is a major advantage. Although EFC has been shown to be effective in separating a single salt and water, it is still in the early stages of being applied to the multi-component hypersaline brines that are typical of reverse osmosis retentates generated by mining and extractive metallurgy.This paper presents an EFC brine treatment protocol developed by the Crystallisation and Precipitation Unit at the University of Cape Town. The protocol incorporates brine analysis, thermodynamic modelling to establish which salts will freeze out and at which temperatures, followed by experimental studies to determine the kinetic parameters, such as nucleation temperatures, salt yields and crystal purity.Case studies showing the application of EFC for the purification of typical brines containing high levels of sodium, chlorine, sulfate and ammonia (Brine 1) and a mixture of sodium and magnesium sulfate (Brine 2) are covered. Modelling tools were applied to describe the phase behaviour of the multi-component saline systems under different process conditions. Experimental validation was carried out using synthetic brines of different (and increasingly complex) compositions. The results showed that EFC could be used to selectively recover the sodium as a sodium sulfate salt from both different brines. The simulation tools were useful in the analysis and understanding of the process.A preliminary economic analysis showed that the operating costs for EC were approximately nine times those for EFC, but the capital costs were much less- equipment for EC cost about half that of EFC. However, it is important to note that the capital cost calculations for EC are based on a technology that is already well established and with only relatively marginal future equipment cost savings expected. In contrast, EFC is a new technology, with significant future technology improvements expected.

Jan 1, 2009

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By Pakalnis Rimas, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

By Jack Curran

KANSAS CITY, MO - Performing one of the most impressive urban building-implosion projects in recent memory, Tulsa, Oklahoma-based Dykon Explosive Demolition Corp. and Omaha, Nebraska-based Anderson Excavating recently felled the landmark Columbia Bank Building in downtown Kansas City, Missouri, USA. Although every structural blasting project presents special challenges, this undertaking was most notable for its unusually unique structural design, tight clearances, and high risk to adjacent structures.

Jan 1, 2003