Search Documents

ASSETS CAPITAL ASSETS Equity in United Engineering Society's Land and Buildings $486,792 79 Library 40,000 00 $526,792 79 INVESTMENTS Jas Douglas Fund-Schedule #2 $ 99,966 40 Life Membership Fund-Schedule #3 9,415 63 R W Hunt Medal Fund-Schedule #4 7,489 09 116,871 12 INVENTORIES Paper Account .305 10

Jan 1, 1923

By N. P. Kripakov

Results of a complex three-seam interaction analysis in a western U.S. coal mine are presented. The physical situation simulated by the models represents the development of a set of entries underneath two previously mined seams with all three seams in proximity to each other. The layout and the geometry of the remnant pillars in the upper seams were nonuniform and not always directly superimposed over each other, creating a very challenging modeling problem. The U.S. Bureau of Mines' MULSIM/PC computer code was upgraded and enhanced to perform the required three-seam interaction calculations. Analysis was limited to simple linear-elastic assumptions as only peak stresses were required. Results clearly indicated that stress concentrations in the lower seam increased approximately 100 percent when compared to cases simulating no extraction in the two upper seams. These stress concentrations generally occurred in zones directly below points of highest abutment pressures in the upper seams. Overall, the model results compared favorably with actual documented observed behavior where roof failures were known to have occurred.

Jan 1, 1996

By L. C. IlsLey

Many accidents rightly classifiable as electrically caused are not so classified for the reason that in numerous accidents the part that electricity played in causing the fatality is only suspected. For instance, a workman might receive a shock that would cause him to lose his balance and fall beneath a trip of cars; if no one saw the first part of the accident, the cause undoubtedly would be charged to "haulage." This paper covers a brief study of fatal and nonfatal electrical accidents. The first usually result from direct contact with the electrical circuit or electrical apparatus; the second more often are the result of arcing or flashing due to handling defective apparatus or making repairs on "live" equipment or circuits. It is hoped that helpful suggestions may be offered for minimizing accidents of these two classes.

Jan 1, 1938

ALABAMA Aldrich.-Lloyd, T W Anniston.-Carrington, F G Gerber, A B Heimrod, A A. White, H E Ashland.-Barton, J C Sturdevant, J C Bessemer.-Abbott, C E Ball, T L Hines, H K Hodgkin, W -0. Salmon, H S Thompson, N E Birmingham.-Adams, J H Adler, J. E Aldrich, T H Aldrich, T H, Jr. Ball, E M

Jan 1, 1923

By Alden B. Carpenter

Brines (a solution containing more than 100,000 mg/l dissolved solids) in sedimentary basins are genetically related to evaporites in one of three ways: (1) dissolution of evaporite minerals, generally halite; (2) interstitial fluids in evaporites which are expelled from their source rock during compaction; (3) incongruent alteration of hydrous evaporite minerals (carnallite). Most brines of commercial interest originate as interstitial fluids in halite-rich rocks. These fluids are initially rich in magnesium, sulfate, and potassium but evolve in composition to an Na-Ca-Cl brine during their migration to their present host rock. A particularly important reaction in this process is: 2CaCO3 + Mgt+ = CaMg(CO3)2 + Cat (1a) This reaction reduces the magnesium content of the brine and ultimately converts it to a calcium-rich brine. The loss of sulfate occurs by two mechanisms. One of these is by direct precipitation as calcium sulfate (either as gypsum or anhydrite): Ca 2+ + SO4 2- = CaSO4 (2a) Additional sulfate may be lost from the brine by sulfate reduction: S042 + 1.33CH2 + 214- = H2S + 1.33CO2 + 1.33H20 (3a) The loss of carbonate species occurs by precipitation as carbonates: H2O + C02 + Cat = CaCO3 + 2H+ (4a) The net result of reactions 3 and 4 is: Ca 2+ + SO4 2- + 1.33CH2 = H2S + CaCO3 + 0.33H2O + 0.33CO2 (5a) The loss of potassium from brines is caused by the formation of potassium aluminosilicates: 2K+ + Al2Si2O5 (OH)4 + 4SiO2 = 2H + 2KAlSi2O8 + H2O (6a) The hydrogen ions produced by this reaction dissolve carbonates: 2H+ + CaCO3 = Ca 2+ + CO2 + H2O (7a) The net result of reactions 6 and 7 is: 2K+ + CaCO3 + Al2Si205 OH)4 + 4SiO2 = Ca2 + 2KA1Si3O8 + H2O + C02 (8a) A study of brines from central Mississippi has shown that the composition of these brines is related to the interaction of pore fluids from evaporites with minerals in the enclosing sedimentary rocks.

Jan 1, 1978

By Gerald P. Scanlan

Control of the dust produced by continuous mining machines in coal mines is generally obtained by water sprays from fixed nozzles mounted on the frame of the machine in back of the cutting head. Mounting the nozzles on the rotating head of the machine closer to the coal cutting bits may improve the efficiency of dust suppression. To test this concept, respirable dust measurements were made during 39 regular production shifts in an underground mine using a Joy 11CM continuous miner. The equipment used, difficulties encountered, and measurements obtained are described.

Jan 1, 1974

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag composition. Liquidus and solidus temperatures and solid solubilities were determined for the BaF2-Y203 system, and the information is presented as the phase diagram. The phase diagram was constructed from data obtained by ceramography, X-ray diffraction, and thermal analysis of specimens encapsulated in small molybdenum ampoules. The data indicate a simple eutectic system with maximum terminal solid solubilities of less than 1 mole pct. The eutectic temperature is 1,343° C, and the composition of the eutectic is less than 1 mole pct Y203.

Jan 1, 1970

By K. E. Stanfield

[Asphalt ~~d road oil ar8 the principal products manufactured from Wyor.1in~ Ilblack oilo" \r,hich, beca.use of th?lir hig.~ E\.sphal t and hig} sulfur COi.1Jce~1t, .!?re difficult e':ld costly to refine into hi?;h-gra.de motor f 101s, burning oils. and lucri ants by presont mothods. Accordin~ly. the demand for truHle asphaltic renidl urn for the construction of roade aJ1.d other uses is 3. controlling factor in the quantity of crud~ oil prod ICed. The increasiilg -u.tilization of special aST>ha.lts as ine}""Pensive bonding, in-]

Jan 1, 1941

Jan 1, 2004

By D. Minney

The quality of resin used in South African collieries is currently controlled according to South African Bureau of Standards, "SABS-1534:2002". It has however been found that resin which passed the SABS tests failed in underground short encapsulation pull tests. An investigation was therefore conducted to determine the characteristics of resins that are currently being used in collieries. A series of in situ short encapsulated pull tests was conducted to determine the effect of expired resin on support performance. The results showed that the longer the time after the expiry date the poorer the resin performance. A series of resin-torque tests has been performed using Anglo Coal's testing facility. The following parameters were investigated on different resins: Spinning speed, Mixing time, and Setting time. An attempt was also made to develop a new quality control procedure for resin. This procedure enables mining personnel to make sure that the quality of resin can provide the required support performance. The effect of spinning speed on resin performance was also investigated. The results showed the resin gelling times of resin decreases as the spinning speed increases. It is found that over-spinning with slow speed roofbolters may result in decreased bond strengths. It was found that a 30-second resin (10-second spin, 30-second hold) should never be spun more than 20 seconds, even with very slow roofbolters (100 rpm).

Jan 1, 2005

Power Point Presentation

Jan 1, 2007

1. Mining directory The mining directory, 1990. Mines and mining equipment companies worldwide. Don Nelson Publications Limited (P.O. Box 193, Barnet, Herts EN4 BLP, England).2. Mintek reports The following reports are available from Mintek, Private Bag X3015, Randburg, 2125 South Africa. They are available at R25 (plus R3,25 GST) per copy to South African addressees, and US$25 per copy (including airmail postage) to addressees elsewhere. There is also an annual-subscription scheme for reports - R400 locally (plus R52 GST) and US$400 (including airmail postage) abroad. The subscription covers al the unrestricted reports published between 1st April and 31st March of successive years, which usualy amount to between 20 and 30. Report M392 Computer programs for optimization by the modified simplex method, by G.L. Moore. Sep. 1989. 25 pp. R25 + R3,25 GST in South Africa; US $25 elsewhere. Report M393 The preparation and certification of fourteen South African silicate rocks for use as reference materials, by E.J. Ring. Sep. 1989.21 pp. R25 + R3,25 GST in South Africa; US $25 elsewhere. Report M395 The separation of trace elements in high-purity rhodium and iridium materials, by R.V.D. Robet and S.M. Graham. Nov. 1989. 10 pp. R25 + R3,25 GST in South Africa; US $25 elsewhere. 3. Publications from Trans Tech The publications listed in this section are available at the prices given from Trans Tech Publications, P .0. Box 1254, D-3392 Clausthal-Zelerfeld, West Germany. Handling of bulk solids. Theory and practice, by P.A. Shamlou. 1988. 200 pp., US$ 59.50. Acoustic emission lmicroseismic activity in geologic structures and materials, by H.R. Hardy and F.W'. Leighton. Vol. I: 1977, 490 pp., US$45.00. Vol. 11: 1980, 500 pp., US$45.00. Vol. Il: 1983, 680pp., US$6O.00. Vol. IV: 1989, 720pp., US$ 75.00. Open pit mine design models. An introduction with FORTRANI77 programs, by E. Alaphia Wright. Early 1990, approx. 200pp., US$75.00. Bucket wheel excavator, by W. Durst and W. Vogt. 988, 450pp., US$118.00. Continuois-surjace mining, by T.S. Golosinski and F.G. Boehm (eds.). 1987, 720pp., US$128.00. Mining-science and technology. 1987, 1430pages, US$ 118.00. Practical handbook for underground rock mechanics, by T.R. Stacey and C.H. Page. 1986, 150pp., US$ 38.00. Professional users handbook for rock bolting, by B. Stilborg. 1986, 150pp., US$38.00. The lighting of underground mines, by D.A. Troter. 1982, 220pp., US$48.00. Elements of hydraulic coal mine design, by M.L. Jeremic. 1982, 16Opp., US$38.00. Continuum theory of rock mechanics, by Cs. Assonyi and R. Richter. 1979, 365 pp., US$ 58.00. Shear and bond in reinforced concrete, by G. Florin.1980, 86 pp., US$ 24.00. Theory and design of surface structures: slabs and plates, by G. Florin. 1980, 222 pp., US$ 24.00. Mineral processing laboratory manual, by A.-Z. Abouzeid. January 1990, approx. 200pp., US$48.00. Weighing and proportioning of bulk solids, by Hendrik Colijn. 2nd ed. 1983, 4OOpp., US$60.00. Solid-liquid flow. Slurry pipeline transportation, E.J. Wasp et al. 1977, 240pp. US$ 58.00. Optimum pipe size selection, by C.B. Nolte. 1978, 304 pp., US$ 60.00.Field instrumentation in geotechnical engineering, T.H. Hanna. 1985, 854pp., US$98.00. The 1990 yearbook and directory. Powder and bulk solids handling and processing. 1989/90, approx. 300 pp., US$ 124.00.

Jan 1, 1990

By David N/A Doucet, Colter N/A Angell, William N/A Joa, Kyle N/A Wagner, Catherine N/A Johnson, Marty N/A Langenderfer

The Kingery-Bulmash (K-B) equations are a widely accepted means of predicting air-blast parameters from surface explosive detonations. The parameters predicted from these calculations include incident and reflected pressure, time of arrival, shock front velocity, incident impulse, reflected impulse, and positive phase duration. K-B calculations are based on curve fitting of experimental data and can be used to predict air-blast parameters for explosive weights from less than 1 kg (2.2 pounds) up to 400,000 kg (440.9 US Tons), and ranges of 0.05 to 40 meters (1.9 inches to 131.2 feet). The K-B equations can also determine the parameters for multiple explosive types using scaled distances and relative equivalency to TNT. An experiment was designed to demonstrate if the measured results for incident pressure, time of arrival, shock front velocity, incident impulse, and positive phase duration equal the expected results reported for the detonation of a small quantity of explosive determined by the K-B Calculator. Three surface-detonated 300-gram (0.66 pound) hemispherical charges of Composition C-4 were observed via high-speed imaging and hydrostatic pressure monitoring. The hydrostatic pressure generated from each charge was measured via piezoelectric pressure transducers at a scaled distance of 10 from the charge epicenter, and at elevations of 0.30, 0.61, and 1.22 meters (1, 2, and 4 feet) above ground level. Variances in experimental values from the K-B predicted values were recorded for each measured blast parameter. Time of arrival, which was redundantly confirmed through high-speed imaging analysis and hydrostatic pressure monitoring, showed the highest deviation from the predicted values at more than double the K-B predicted value. This report compares the observed blast parameters from the test series with the expected blast parameters from the Kingery-Bulmash Blast Parameter Calculator. Differences between the experimental and predicted values are reconciled through analysis and discussion of testing conditions, instrumentation setup, and scaling methods.

Jan 1, 2019

By D. Michael Holloway

The realignment of Interstate 880 replaces the double-decked (Cypress) viaduct collapsed in Oakland, California during the 1989 Loma Prieta Earthquake. The California Department of Transportation (CALTRANS) evaluated several pile foundation schemes for supporting the proposed structures. Structural support demands led to the selection of steel pipe piles (16-, 24-, and 42-inch-(406-, 610- and 1067-mm-)diameter), filled with concrete and steel reinforcement. Deep penetrations required through layers of very dense/cemented sands in some locations, caused serious drivability and pile integrity concerns. The need for large pile driving hammers and large diameter steel pipe piles pushed the engineers and prospective contractors well beyond the limits of local experience. Such questions as the feasibility of driving the pipes closed-ended through dense upper strata, and quantifying the effects of installation on the long-term capacities of the piles, led CALTRANS to develop a comprehensive pile test program to address the design and construction issues effectively. The results were furnished to prospective bidders on the production stages of the ensuing contracts.

Jan 1, 1996

By J. Mitchell Linne

The principal mineral commodity in the Orleans Mountain RARE II area (No. 35019) is gold. Gravel deposits along the Salmon River contain placer gold. Lode gold with associated silver is contained in quartz veins. Many placer mining claims have been located within the study area in the Salmon River district. Four placer patents totalling 230 acres were issued for claims on the Salmon River between Lewis Creek and Forks of Salmon. On this same reach of river, adjoining and overlapping the study area boundary, approximately 3.3 million cu yd (2.5 million cu m) of gold bearing gravel with values ranging from $0.51 to nearly $5 per cu yd (50.66 to $6.50 per cu m) (gold valued at $400 per troy oz), are contained in three placers, the Bloomer, Pot Luck, and Horn (table 1). Within the study area boundary there are approximately 950,000 cu yd (726,000 cu m) of gold bearing gravel in these three placers. These three mines yielded nearly 12,000 oz (373,000 g) of gold and more than 300 oz (25,000 g) of silver between 1872 and 1913.

Jan 1, 1982

By Richard L. Rains

The Bureau of Mines made a study of mines and prospects of the Benton Range RARE II area (No. 5056), Mono County, California in October and November 1980. The study area is west of Owens Valley and 30 mi (40 km) north of Bishop, California. The mineral deposits were evaluated by examination of mines, prospects, and mining claims by the Bureau of Mines. Geological, geochemical, and geophysical studies were conducted by the Geological Survey. The principal mineral commodities of the Benton Range RARE II area are gold and silver but tungsten deposits may also extend into the area. Properties with resources are listed in table 1; their locations are shown on figure 1.

Jan 1, 1982

By B. F. Naylor, C. H. Shomate, F. S. Boericke

"Ilmenite is the most important titanium-bearing constituent of titaniferous iron ores. Such ores, of which the United States has abundant reserves, are of interest because they constitute an important potential source of both iron and titanium that may be tapped in times of stress, and which eventually may be utilized in the normal course of events.As the iron and titanium constituents of titaniferous iron ores are not completely separable from each other by ore-dressing methods, any process for metal recovery will, of necessity, involve reduction of the iron in ilmenite. Consequently, knowledge of the thermodynamic properties of ilmenite should supplement information already available concerning those ores. With this in view, the Pacific Experiment Station of the Bureau of Mines undertook to evaluate thermodynamic properties; the data obtained are the subject of this report.Three types of experimental work were involved. First, low-temperature specific heats of ilmenite were measured in the temperature range 500 to 29S° K. These data serve to evaluate the entropy, a quantity necessary for a reliable evaluation and correlation of other thermodynamic properties. Second, high-temperature heat-content measurements were made in the temperature range 298° to 1,743° K. The data serve to bridge the gap between room temperature and elevated reduction-process temperatures. Finally, hydrogen-reduction equilibria were measured in the temperature range 1,220° to1,375° K. These data-give a direct measure of the free energy of reduction of ilmonite at these temperatures and, in conjunction with results of the other two types of measurements, serve to obtain the heat of formation of ilmenite, a quantity not readily determinable by direct calorimetric means.The data are correlated to form a composite, self-consistent portrayal of the thermodynamic properties of ilmenite, which may be used in evaluating the efficacy of any reducing agent of known thermodynamic properties. Selective-reduction of iron in ilmenite by hydrogen, carbon monoxide, and carbon are considered in this report."

May 1, 1946

Electric power curtailments resulting from the coal strike, required Noranda Aluminum, Inc. to shut down its 140,000 ton-per-year (tpy) primary aluminum smelter at New Madrid, Mo., and layoff 308 workers. Other primary aluminum production facilities affected by the coal strike included the Aluminum Company of America plant at Evansville, Ind. which shut down half of one potline; the Eastalco Aluminum Co., smelter at Frederick, Md., which cut production by 7 percent; and the National-Southwire Aluminum Co. plant at Hawesville, Ky. which cut production by 6 percent. Alumax, Inc. announced that construction had started on a 91,000 tpy potline at the Eastalco primary aluminum smelter. The new potline will be owned 65 percent by Alumax and 35 percent by Mitsui & Co. Ltd. Howmet Aluminum Corp., which currently owns 50 percent of the existing 176,000 tpy facility, has the option of becoming a 50 percent owner of the third potline in 1982. Construction of the new line was scheduled to be completed in 1980.

Jan 1, 1978

By Oliver C. Fursman

These investigations were conducted to determine conditions for recovery of nickel and copper from Funter Bay, Alaska, sulfide ore and recovery of nickel from nickel-silicate ore, Nickel Mountain, Riddle, Oreg. Samples of Funter Bay cupriferous and nickeliferous pyrrhotite ore, were treated by beneficiation, roasting, electric smelting of roasted are for matte production, chlorination, leaching, and sulfatizing roasting with subsequent leaching. Funter Bay and Nickel Mountain ores were smelted together to produce matte. Total sulfide flotation, followed by magnetic separation of the tailings to recover entrained nickel-bearing pyrrhotite, resulted in the highest nickel recovery in beneficiation tests on Funter Bay are. Overall beneficiation resulted in recovery of 98.5 percent of the copper and 95.4 percent of the nickel in the concentrate that contained 3.5 percent copper and 1.7 percent nickel.

Jan 1, 1962

By B. R. Palmer, M. C. Fuerstenau

Oxide and silicates respond to flotation with a large number of anionic collectors. These include carboxylates (fatty acids), sulfonates, alkyl sulfates, and certain chelating agents. In contrast to sulfide mineral flotation, relatively long-chained collectors (generally longer than 10 carbons) are required to effect flotation of this group of minerals. The structural formulas of these various anionic collectors are presented in Table 1. Formulas and solubilities of various fatty acids are presented in Table 2. These solubilities are those of the dissolved and undissociated species of the acid, e.g. oleic acid, HOl(aq). Of the compounds listed, oleic acid and abietic acid, which IS a major constituent of talloel, are used most commonly in commercial applications. The usage of these two collectors is related to cost and effectiveness. In addition to their high molecular weights, oleic acid contains a double bond in its hydrocarbon chain, while abietic acid is comprised of aromatic rings containing double bonds. The presence of double bonds increases solubility significantly over that of saturated homologues. Stability of metal-collectors assumes a most significant role in these systems, and the solubility products of various metal carboxylates and sulfonates are listed in Tables 3, 4 and 5. In addition to these properties, strength of the acids of these various anionic collectors is also important. The carboxylic and hydroxamic acids are weak acids whereas sulfonic and alkyl sulfuric acids are strong acids. All of the carboxylic acids fall in the range of pK = 4.7 ± 0.5 ([2]); the pK of hydroxamic acid is around 9 ([3]); and the pK of sulfonic acid is about 1.5 ([4]).

Jan 1, 1976