Search Documents

By Clyde DeRossett

Surface fractures, sometimes of significant size, are observed in eastern Kentucky over high extraction areas. Field observations were correlated with mine maps and a regional subsidence prediction computer model. The opening of large fractures is attributed to the presence of a pre-mining joint system, which exists near outcrop in the eroded Appalachian plateau. Lithological composition of the overburden influences the process of fracture opening. No correlation was found between the areas of the predicted maximum horizontal extensions and the actual location of fractures. In this paper a mechanism of fracture formation as a result of the high extraction mining is presented, with recommendations for mine planning to minimize surface damage.

Jan 1, 1993

By Robert H. Merrill

Several investigators have obtained solutions for the concentration of stress around circular, ovaloidal, elliptical, and rectangular holes in an elastic, isotropic, semiinfinite plate subjected to uniaxial and biaxial stress. These solutions are used to evaluate the changes in stress around openings immediately under the undercut normally used in conventional block caving operations. The evaluations are based on the assumption that a horizontal undercut removes most of the vertical component of a biaxial stress field. The location and magnitude of the significant changes in stress concentration around the opening are computed. Conditions under which the assumptions used in the evaluations may or may not be consistent with conditions around block caving mines are discussed, and examples of preferred opening shapes for a biaxial (hydrostatic) stress field are shown. This report is a summary of one phase of an investigation to establish design methods for the size and shape of mine openings used in block caving mining methods .

Jan 1, 1962

By P. A. Croce

A total of 17 mine gallery fire tests (23 including sub-tests) were completed during this report period (10/1/76 - 11/30/77), directed at identifying a hazardous timber-set fuel-loading in a mine passageway that is otherwise free of combustibles. Results of these initial tests show that the capability of a particular fuel loading for propagating a fire is dependent upon the imposed ventilation air velocity and the ignition intensity, although this dependency needs to be better defined. It is also apparent that care must be taken when relating gallery test fire behavior to actual mine fire behavior, because of the restrictive length of the gallery. Present data indicate that some modification to the instrumentation scheme may be advantageous before proceeding with future tests.

Jan 1, 1978

By Gilles Rousset

This paper presents laboratory experiments conducted on hollow cylinders samples. The advantage of such a geometry is to approach in situ conditions around cylindrical openings (lined galleries, boreholes, ...). Many authors have been interested in this kind of problem, especially for borehole stability applications (for references see Guenot 1987). However, as long as we know, time-dependent behavior has not been well studied. For this purpose, we have set up two different types of tests on a deep clay : - Quick unloading test, to assess the influence of unloading rate on mechanical response and the failure modes. - Creep and relaxation test, to compute the time dependent overall deformation of the hole wall as well as to plot long term convergence-confinement pressure curve. The experimental results are then compared with those given by a theoretical model developed in our laboratory, well fitted with the tested material.

Jan 1, 1989

Workers at the Consolidated Aluminum Corp. primary aluminum smelter at Lake Charles, LA walked out at midnight March 31 when their contract expired. Management personnel operated the smelter and prebaked carbon anode facilities until an agreement for a new 3-year contract was reached April 18. The Aluminum Company of America (Alcoa) began operations at its can recycling facility at Taylor, MS. The facility can process 3 million pounds per month of aluminum and steel cans. Alcoa announced plans to increase the capacity of its aluminum paste and flake production plant at Logan's Ferry, PA by 50 percent. Completion was scheduled for mid-1980.

Jan 1, 1979

By F. J. Prokoski

The COALSTAR Project, which operated from November 1981 to December 1982, was a research and development project aimed at providing a reliable and inexpensive means of monitoring various waste site conditions via the GOES satellite system. The GOES system provides data transfer from unattended isolated sites where neither power nor telephone lines exist. The reliability and resolution of the data received while using the satellite link were excellent; however, the site instrumentation gave considerable trouble. The disastrous failure of a large coal waste embankment in 1972 led the Bureau of Mines to undertake a comprehensive program to reduce the likelihood of such an occurence again. Part of this program involved the installation of instruments to monitor the stability of a specially-selected embankment operated by Armco Incorporated near Montcoal, West Virginia. Initially, the instruments were monitored by normal telephone lines and used normal commercial power from the local utility. The project described here was initiated to replace this monitoring system with an unmanned, solar-powered data collection system which transmitted data via satellite to a central computer facility. The satellite data network is the National Earth Satellite Service of the National Oceanic and Atmospheric Administration.

Jan 1, 1984

By Theresa M. Bodus

The strength of roof shales is, in part, a function of the preferred orientation of clay minerals within them. Therefore, analysis of clay fabric under both air-dried and hydrated conditions should be helpful in understanding roof shale failure. Core samples were collected from the Energy, Anna, and Lawson shales, which are locally present as roof shales of the Herrin No. 6 coal of southern Illinois. The Clay Fabric Index (CFI) was measured for thirty core samples, using X-ray diffractomtry, to investigate the relationship between clay fabric and roof collapse in coal mines. Greater CFI values indicate a weaker preferred orientation among clay minerals, which generally results in a weaker inter-grain bond. Average CFI values for air-dried samples were: 0.15 for Anna shale; 0.20 for Energy shale; and 0.37 for Lawson shale, .After the introduction of water, average CFI values increased to: 0.28 for Anna shale; 0.22 for Energy shale; and 0.43 for Lawson shale. The laboratory results indicate the following: [l] under air-dried conditions, Anna shale is the most stable, followed by Energy and Lawson shales; and 121 under hydrous (mine) conditions, Energy shale is the most stable, followed by Anna and Lawson shales. In mine environments where roof failures involving Energy shale have occurred, planar trends delineated by a relatively high density of small (0.2-4 cm diameter) iron concretions have been reported along the failure surface. Radial cracks have been observed around unsealed anchor bolt holes in the Anna shale. Instability of the Lawson shale is ubiquitous in coal mines. In the laboratory, similar physical changes were noted in the shale samples after the introduction of water, including [l] increased hydration around the perimeter of iron concretions in Energy shale, [2] radial extension cracks in Anna shale, and 131 extreme slaking of Lawson shale. Measured increases in the CFI reflect the observed physical changes of the samples upon the introduction of water, which probably reflect changes in strength that may result in roof failures in hydrated mine environments.

Jan 1, 1989

By John A. Johnson

The purpose of this report is to clarify the interpretation of some phases of previous progress reports5/ on the use or omission of stemming that have been brought to the attention of the authors by readers. As the stemming problem was approached from an entirely disinterested viewpoint and the data were presented impartially, results of investigations published in previous reports5/ were obtained under a definite set of conditions and procedure, and they may of may not be duplicated under different conditions and procedure in actual mining practice. Final conclusions regarding the use or omission of stemming in blasting have not been reached pending completion of all aspects of this investigation.

Jan 1, 1942

By John A. Johnson

The purpose of this report is to clarify the interpretation of some phases of previous progress reports5/ on the use or omission of stemming that have been brought to the attention of the authors by readers. As the stemming problem was approached from an entirely disinterested viewpoint and the data were presented impartially, results of investigations published in previous reports5/ were obtained under a definite set of conditions and procedure, and they may of may not be duplicated under different conditions and procedure in actual mining practice. Final conclusions regarding the use or omission of stemming in blasting have not been reached pending completion of all aspects of this investigation.

Jan 1, 1942

By Blott S. F

The smelting plant and equipment at Mount Isa, as originally designed and built, was described by J. M. Callow (1) *.F. A. Forward (2) described alterations and additions to the plant and discussed the metallurgy of mixed carbonate-sulphide concentrates at Mount Isa, prior to 1933, in the Proceedings of this Institute.In 1933, A. F. McAskill (3) gave full mechanical details of the plant in a paper presented to the Institution of Engineers, Aust.FLOW SHEETSFig. No. 1 represents the present general flow sheet. Forward's (2) flow sheet is reproduced here as Fig. lA, and will serve for comparison in depicting subsequent deletions from, and alterations and additions to, the plant.Fig. No. 2 presents the daily tonnage flow sheet of 1939 practice.ALTERATIONS SINCE 1933General. Many changes in metallurgy and operation have taken place, particularly subsequent to March, 1935, when the treatment of a mixture of carbonate and sulphide ores was discontinued and the mill commenced operating on all-sulphide ore. This alteration brought about the elimination of gravity concentration-Jigs and Tables and resulted in the production of all-floatation concentrates of a very fine sizing. Refer Table No. 2, page?) Radical changes in the analyses and physical nature of concentrates also followed (see Table Nos. 1 & 2, page ?) and, similarly, radical changes in the smelting plant have been slowly brought about.

Jan 1, 1939

By L C. P J Fonteneau, B Godel, E R. Ramanaidou

The Hamersley Province in Western Australia hosts large iron ore deposits. Each deposit displays various iron ore types that were defined on their metallurgical properties, especially in terms of porosity and mineralogy. Conventional porosity and mineralogy information on iron ore types are provided on 2D thin sections using automated image analysis with scanning electron microscopy (SEM)-based techniques combined with chemical analyses. However these techniques cannot accurately quantify the 3D porosity. High-resolution X-ray computed tomography (HRXCT) is a non-destructive technique providing a 3D image of the sample with a resolution close to 0.5 - 0.7 ¦m for samples size of up to few centimetres in length. 3D image analysis using customised algorithms now provide accurate quantitative porosity and mineralogy of iron ore types.CITATION:Fonteneau, L C P J, Godel, B and Ramanaidou, E R, 2013. Application of high-resolution x-ray computed tomography to iron ore characterisation, in Proceedings Iron Ore 2013 , pp 243-250 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Kenji Koga

In order to derive the population distribution of gold nanoparticle morphologies as a function of size, highresolution electron microscopic (HREM) observations and structural analyses were done for over 4000 particles (3-18 nm) grown by an inert gas aggregation (IGA) source using helium. To obtain structural features threedimensionally and not to skip high-contrast images, twenty photos were taken for each particle by changing tilting angle of a specimen holder in combination with the through-focus procedure. For the reliable structural determinations, HREM images and their tilting sequences were directly compared with multislice-simulation results for icosahedral, decahedral and face-centered cubic morphologies, and finally the population distribution of each morphology was obtained as a function of size. In the present sample, icosahedral particles were dominantly populated over the whole observed size range and decahedral particles with non-spherical truncated bi-pyramid shape were secondly dominant. Even though a large number of sampling has been done, few crystalline particles were observed.

Oct 1, 2003

By G. F. Skala

Additional testing of two prototype instruments for the discrete detec­tion of submicrometer particles in metal and nonmetal underground mines is described. The detectors are designed to utilize properties of submicrometer particles to distinguish between those produced by fires from mine ambient particles primarily resulting from diesel engine exhaust. One instrument is based on the ability to pyrolyze fire produced parti­cles, but not diesel exhaust particles. An alarm is produced when the ratio of pyrolyzed to unpyrolyzed particles exceeds a preset value. The other detector utilizes a continuous flow ion chamber preceded by a denuder to remove charged particles. Discrimination against diesel produced submicrometer particles results because the diesel particles are naturally more highly charged than fire produced particles. In-mine testing was conducted over a period of several months. Both in­struments exhibited an ability to discriminate against diesel exhaust. However, problems with the recording equipment, and with the instruments themselves, due to large ambient dust particles, prevented enough data from being obtained to choose between the two methods. Recommendations to correct the problems are made.

Jan 1, 1982

By Carl Lubbe, Ron Frye

Numerous articles have been written regarding the effects of blast control plugs in an attempt to quantify stemming ejection rates, air overpressures, fragmentation’and other parameters measured using these devices. In an effort to further attempt to understand the function of these devices, field and laboratory research conducted with various stemming devices was performed to enhance existing data sets and analyze otherphenomena that occur when these products are used.

Jan 1, 1998

By Robert L. Frantz

The performances of the three bituminous coal demonstration methane re¬covery boreholes, located in Greene County, Pennsylvania, are reviewed. Development of these vertical holes was largely underwritten by project funds. Reference is also made to an anthracite coal methane project in Luzerne County, Pennsylvania. This involved one vertical hole and was underwritten by a utility company. In addition, an exploratory drilling in the southern anthracite, which provided the project group with coal cores for methane gas analysis, is also cited. The technical and economical data that were gathered from the various methane projects are analyzed. Finally, the advantages and disadvantages of methane recovery by vertical boreholes are assessed.

Jan 1, 1978

By Allan Sylvester

This paper will discuss the design, construction, and performance of the support of excavation on the San Diego State University LRT Station. The vertical elements of the system include drilled secant piles and drilled soldier piles. We will discuss the geo-technical characteristics, design and construction considerations, loading criteria, construction techniques, schedule constraints, and performance of the pile and support of excavation systems. In consideration of the conference theme, there will be a discussion of the successful accomplishment of meeting the interim milestone dates of the Contract. The project team cooperatively worked to design and install approximately 1,100 drilled secant and soldier piles as well as excavate and install the balance of the support of excavation elements in such a manner as to minimize the disruption to campus students and operations.

Jan 1, 2002

By Yoginder P.

ACKNOWLEDGEMENTS Authors sincerely appreciate the interest, cooperation and technical support of the coal company management and staff in conducting the study. Without their assistance this study would not have been possible. INTRODUCTION AND SPECIFIC OBJECTIVES An area in the midwest overlying abandoned room-and-pillar mine workings at, shallow depth has been experiencing subsidence movements with associated damage to surface structures. Other coal companies in the area have also been having similar experience. A 16 - month cooperative study between a mining company and the Department of Mining Engineering at SIUC was developed with the following objectives. 1) Determine the extent to which surface and subsurface movements were complete in the area, 2) Identify the mechanism(s) of subsidence in the area, 3) Determine the influence of geology and hydrology of the area on subsidence movements, 4) Observe the conditions of abandoned underground workings with a borehole TV camera, 5) Characterize the extent of damage and monitor possible progressive damage to selected surface structures, and 6) Make recommendations to a) minimize further damage to surface structures in the area, b) identify future areas that may be affected by these movements and c) modify mining systems to minimize these movements.

Jan 1, 1986

By Floyd C. Bossard

Major air-cooling facilities have been installed and are operating underground in U.S. copper mines (at Butte, Montana and Superior, Arizona), South African gold mines, European coal mines, Zambian copper mines, Kolar gold mints in India, Coeur d'Alene mines of Idaho, plus other locations. Mining districts that utilize spot cooling and local air-cooling facilities would increase the above listing many times. The principal objectives of underground mine air cooling systems are to; 1. Extract heat and water vapor from the mine air and provide for their removal from the mine via (a) water pumped to surface or (b) discharged mine exhaust air. 2. Provide acceptable artificial ambient conditions for efficient working mine development and production areas. 3. Recondition used air, thus supplementing the limited mine ventilation balance. In deep South African gold mines, when rock temperatures exceed about 105°F, cooling of underground air becomes necessary for the poorly ventilated sections of the mine. By U.S. standards, air conditioning in poorly ventilated mines usually commences when the virgin rock temperature exceeds 100°F. On the other hand, well ventilated deep vein-type mines in the U.S. have been able to forego general cooling of mine air until the mines have been extended to such depths that the virgin wallrock temperatures have exceeded 115° - 120°F. It must be noted that spot-cooling of selected development headings may be required in many mines where rock temperatures exceed 100°F. Such local air-cooling practices permit the driving of long headings for exploration or extended development prior to holings which result in establishment of primary ventilation circuitry. The following summary reports on current practices of cooling and dehumidifying mine air. General system descriptions with important details will hopefully permit the reader to gain an understanding of the subject. A list of references is provided for this serious investigator who desires a more thorough knowledge-base and who is responsible for the design of a mine air-cooling system.

Jan 1, 1973

By Georgene Renner, William R. Yernberg, Steve Kral

ABB offers complete electrical revamps of mining shovels with ac or dc drives, drive control, frequency converters with insular gate bi-polar transistor technology, intelligent control packages and visualization. Many of the world’s shovel excavators and draglines (walking excavators) were built in the1980s. After 15 to 20 years of round-the clock operation in openpit mines, these machines start to feel their age. Electrical parts are particularly vulnerable. Their performance deteriorates and availability and productivity fall. Even with regular ser-vice and maintenance, a machine of this age will accumulate 400 hours of unscheduled downtime a year. The need for a replacement becomes pressing, but the expense is often prohibitive.

Jan 1, 2005

By D. L. Putnam

Snap Lake Mine ?? Complex dyke ore body ?? Underground operation ?? 1.1 million tonnes per annum ?? 1.2 carats per tonne ?? On-site diesel power generation ?? Supply by ice road and air ?? Milestones ? Construction commenced in 2005 ? Commissioning 2007 ? First diamonds August 2007

May 1, 2008