Search Documents

By Diane M. Doyle-Coombs

In late July 1985, air samples from a sealed portion of the Quinland coal mine in West Virginia showed the presence of carbon monoxide (CO). Mine Safety and Health Administration (MSHA) personnel concluded that a fire was burning behind the seals. Since an imminent danger existed, the mine operator was given a closure order. The gases behind the seals were monitored and almost 2 million ff of carbon dioxide (C02) gas was pumped into the sealed area to stabilize the environment. Sixteen days after the closure order was issued, MSHA allowed the mine to return to production. Approximately 1 yr later, mine management submitted a seal breaching request to MSHA in order to drive a set of entries to further develop the mine. The Bureau of Mines established a sampling strategy and monitored gases from behind the sealed area during the breaching operation until the atmosphere was safe. This report is an account of the seal breaching conducted by the mine, MSHA, and the Bureau. The logistics of this event, the sampling strategy, and the equations applied could be used by the mining industry in future breachings or mine recovery operations. Time to reenter the area was calculated by using the methane (CH4) concentrations sampled at the discharge of the seals. Tracer gas was used to verify the ventilation flows through the area.

Jan 1, 1988

By Michael Hamilton

Mineral resources have been identified at seven properties in the, Middle Fork Judith study area (fig. 1, and table 1). Commodities consist of silver, gold, copper, lead, zinc, and marble. Eleven properties (fig. 1 and table 2) have potential for discovery of silver, copper, lead, zinc, or sapphire resources. Of principle interest are the mineral deposits within contact zones between the Yogo intrusive complex and the surrounding Paleozoic sedimentary rocks. Contact alteration zones along the southern slopes of Yogo Peak have been prospected in a 2- to 3-mi (3.2-to 4.8 -km) long belt within the study area.

Jan 1, 1982

By Verne E. Hooker

This Bureau of Mines report summarizes the results of modifications in the borehole deformation gage design and subsequent changes in the overcoring techniques. Modifications in the borehole deformation gage have greatly improved the creep characteristics and enhanced the versatility of the gage. In situ field tests in competent rock near St. Cloud, Minn., provided sufficient data to compare the reliability between gages and new techniques in obtaining good engineering estimates of stresses. Near-surface horizontal stresses at the test sites are compressive and biaxial in nature.

Jan 1, 1974

By J. J. Montoro

The influence of blasting on the excavators’ efficiency, defined as mucking rate (amount of rock mucked per unit time) and mean bucket load (amount of rock loaded in each bucket operation), is investigated. Rock characteristics, blasting parameters (drill pattern, explosive energy, and charging), and the excavator’s performance (truck loading time and number of buckets to fill a truck) were monitored in eleven blasts in an open pit iron ore mine. ANFO, ANFO/emulsion blend, and watergel were used in the blasts and the powder factor was varied between 0.98 and 1.45 kg/m3. The mean bucket load is mainly affected by the bucket size, which is independent of the blasting parameters. Besides the relation with the mean bucket load, the mucking rate was found to be positively correlated with the explosive energy, whereas no significant correlation with the rock properties was found. The analysis of the data, together with other published works, suggests a non-monotonic relation of the mucking rate with the powder factor, with a maximum mucking rate at a certain powder factor. This is especially true when the useful work of the explosive per unit rock volume is used rather than the classical mass powder factor and when only the amount of explosive above grade is considered.

Jan 1, 2007

By J. H. Daniel

This report, summarizing the results of two studies sponsored by the Bureau of Mines, presents information on the types of mobile machines used in surface coal mines in the United States, and the amount of noise to which miners are exposed. Data consist of a calculated value of the probability of noise overexposure caused by specific equipment. These data are extrapolated to estimate the number of overexposed operators. Bulldozers were identified as the major contributors to noise overexposure, and the report presents results of a Bureau-funded program on the feasibility of providing retrofit noise control on bulldozers.

Jan 1, 1980

By Gary E. Sherman

To aid the U.S. Army Corps of Engineers in their Resource Development Navigation Study, the U.S. Bureau of Mines (Bureau) examined the potential for mineral development near ten Alaska port sites. This report presents the results for the following four sites: Balboa Bay, Beluga, Lost River, and Point MacKenzie. There are 579 known deposits within the area considered for these ports. The majority of the deposits are located within a highway/railroad corridor examined for the Point MacKenzie port site. Based on the current level of knowledge, coal deposits near the Beluga and Point MacKenzie port sites are most likely to be developed in the near future. This conclusion is based on the fact that coal projects in these areas are actively being pursued for development. The mineral wealth surrounding the four port sites is substantial. Mine models were used to examine the potential for mining tin, gold, silver, copper, and molybdenum. The models were based on published reserve and grade data and therefore do not include proprietary company data which, if available, would likely change the analysis results. Of the models examined, the tin placer mine model developed for the Lost River port site proved to be closest to being economic.

Jan 1, 2011

By Eugene T. Sheridan

The 24th annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, revealed that 76 producers in 20 States reported commercial production of peat in 1957. In addition to the States that reported production in 1956, Colorado, Idaho, and Wisconsin produced peat in 1957 Forty-four producers reported humus production; 21, reed-sedge peat; and 22, moss peat production. This total exceeds the number of active plants but several producers recovered more than one type of peat. Fifty percent of the total production was reported as reed-sedge peat, 36 percent as humus, and 14 percent as moss peat. About one-sixth of the total production was raw peat, with no preparation other than being air-dried. The remainder consisted of processed peat prepared for use by cultivation, shredding, and/or kiln drying.

Jan 1, 1958

By José D. T. Capocchi

Viscosity of liquid lead, tin, and Pb-Sn alloys has been measured by the rotational viscometer method in the temperature range from 50 K above their respective liquidus temperature to 823 K. The results are accurate to within ±1.0 %. The variation of viscosity with temperature followed the Arrhenius-type equation µ = µo.exp(Q/RT). The composition dependence of the isothermal viscosity and the activation energy for viscous flow have not shown anomalous changes at the eutectic composition of the Pb-Sn system.

Jan 1, 2000

By J. P. Kennedy, O. A. Bascur

Large metallurgical complexes have more data than a small city and these data change as internal and external conditions evolve. Staffing turnover hinders experienced-based decisions especially with simple tools like spreadsheets. Lack of current information can contribute to decisions that result in significant deterioration in the quality of operation. Timely, unified information from sophisticated analyses presented to the broadest possible reach will improve operation. The major innovation is the addition of the web browser to the suite of software people will use with no training – the other two are spreadsheets and graphical presentations – and the consistent organization and transformation of the real time data to support broad access. This paper describes the data transformations and presentation methods necessary for a Web view, especially the special needs of real time data and analysis required for active operations decision-making. Many people inside and outside the complex, not just operators, need timely information that is abstracted, aggregated, organized and unified. Unification and aggregation of real time data presented via the Web opens a new paradigm for collaboration. The analysis tools are as important as the data. These rule-based tools add significantly to the operations database in the form of results stored for viewing with plant data. Mining and metallurgical plants already use many sophisticated analysis tools such as predictive maintenance policies based on statistical analysis vibration analysis, and oil and lube analysis for critical equipment. These add real time events, similar to an alarm package, and unified production information to the operational database. Simple models are used on line to create key indices that provide a real time indication of performance. Key indices include metrics for losses due to plant availability, performance efficiency, and overall process equipment effectiveness. These additional data in the operations database are used for early fault detection, increased production, better quality, higher availability of equipment and faster detection of process bottlenecks. An important feature is the ability for people to create their own key indices and store the results for use by anyone in the plant historian, but accessible by a browser. Keywords: plant information, principle components analysis, data reconciliation, gross error estimation, Internet, Word Wide Web

Jan 1, 2002

By S. M. Shelton

Tests employing various ore-dressing methods were made on a manganese wad ore from the W. A. Chinn property in the Batesville-Cushman district of Arkansas in an effort to develop a practicable procedure for the production of ferromanganese-grade concentrates. The ore body occurs as a bed approximately 7 feet thick in the residual clay of the Ferndale limestone formation5/. The crude wad ores are soft aggregates of various oxides of manganese, which are loosely bonded together. Hard lumps of high-grade ore are disseminated throughout the wad. Hausmannite, pyrolusite, and psilomelane are the principal minerals. Some clay is present, but most of the gangue consists of leached fragments of the original siliceous and calcareous rocks in which the manganese occurred. In addition, hydrated oxides of iron, which axe present, also must be considered as gangue. Definite phosphate minerals have not been identified.

Jan 1, 1942

By John W. Fredland

Many accidents occur in the mining industry as a result of the instability of material during handling and processing operations. Accidents due to dump point instability at stockpiles, and at spoil or waste piles, for example, occur with alarming frequency. Miners must be trained to be better aware of these hazards. Information on safe working procedures at stockpiles and surge piles is provided. Mine operators must review their training and operating procedures regularly to ensure that hazardous conditions are avoided.

Jan 1, 1993

By James J. Scott

Research and development has been carried out on the patented Dynamic Rock Anchor, tradenamed DYNA-ROK and DYNA-ROK PLUS Anchors, which are manufactured and marketed by Ingersoll-Rand Company. This paper will present the results of field testing of this revolutionary new concept in ground control. Geologic conditions will be described where the plastic sleeve of the DYWA-ROK anchor alone is sufficient to provide anchorage and also, where in softer ground conditions, the DYWA-ROK PLUS is applied. The rationale for making the decision as to the type of fixture to be employed, the length of plastic tube to be used and the quantity of resin are explained. Pull test data will be shown from eight different coal seams in the Eastern United States where the product has been installed.

Jan 1, 1990

By T. Holmes, J. Middlemiss

"Agnico-Eagle (AE) has been operating their Kittila Mine in Northern Finland since 2008. The mine has experienced considerable ore flow problems with ratholing, bridging and freezing in their mill feed bin since start up. In the first winter of operation, the entire central portion of the contents of the cylindrical flat-bottomed 2000 tonne mill feed bin froze. Flow was erratic and could only be achieved through small diameter ratholes. To maintain a reasonable, albeit limited, feed to the mill, the bin had to be kept less than ½ full and a portable steam generator was brought in to melt the frozen agglomerates that frequently blocked the outlets. The combination of limited surge capacity and frequent outages required the crushing plant to operate 24/7 and resulted in inconsistent production levels and high operating costs.AE had planned to expand the processing plant to increase throughput by about 30% when they transitioned from open pit to underground ore. These plans presented an opportunity to improve the material handling.To avoid the problems experienced with the original mill feed bin, AE enlisted Jenike & Johanson Ltd. (J&J) to test samples of the ore, and based on the measured flow properties to provide design recommendations to ensure that the new mill feed bin would operate reliably. The new 2000 tonne expanded flow mill feed bin and apron feeder were installed in 2014 and are now supplying almost 93% of the total mill feed with the remaining coming from the original bin.IntroductionIn early 2009, AE engaged J&J to visit their then recently opened Kittila mine and mill in Northern Finland (Figure 1). Over the first half-year of operation, production had been restricted in the ore handling and storage system by flow problems such as ratholing, bridging and freezing including blockages of chutes and hoppers as a result of frozen fines buildup and large frozen agglomerates. AE wanted to increase production in the existing open pit mine and mill feed operation and also wanted to avoid similar ore handling problems when they commissioned the new underground mining system under development at that time."

Jan 1, 2017

By R. R. Joseph, K. A. Gschneidner

The solid solubility of magnesium in the close-packed modifications of lanthanum, cerium, praseodymium, neodymium, gadolinium, dysprosium, and lutetium was determined from approximately 250°C to the eutectoid temperature by the X-ray parametric technique. The maximum solubility at the eutectoid temperature was found to be 9.4 at. pet in La, 8.2 in Ce, 9.2 in Pr, 8.2 in Nd, 14.1 in Gd, 13.5 in Dy, and 11.5 in Lu. The solubility when compared at a homologous temperature was found to increase in a smooth manner with decreasing size factor from lanthanum to lutetium. It was found that the apparent atomic radius of magnesium when dissolved in the lanthanide solvent was constant and could be accounted for by consideration of several models dealing with departures from Vegard's law. The eutectoid temperatures for the lanthanide-rich La-Mg, Ce-Mg, and Nd-Mg systems were found to be 544", 505°, and 551°c, respectively. A study of the solid solubility of magnesium in the lanthanide metals was initiated because the valency and electron egativity difference are essentially constant and favorable for solid-solution formation, and thus one could examine the effect of size on terminal solid solutions. The size factors based on metal radii range from 14.6 pet for lanthanum to 7.5 pet for lutetium. Since the electronegativity difference is small, 0.06 unit or less, application of the Hume-~othery' and Darken and Gurry2 criteria for solid-solution formation indicates that the solubility of magnesium would be expected to be small for lanthanum (between 5 and 10 at. pet) and to increase as we proceed along the lanthanide series. A search of the literature revealed no data on the solubility of magnesium in the lanthanide metals except for the solubility of magnesium in cerium at 450oCA typical phase diagram for the lanthanide-rich end of the lanthanide-magnesium phase diagram is shown in Fig. 1. EXPERIMENTAL PROCEDURES Preparation of Alloys. The lanthanide metals used in the preparation of alloys for this investigation were prepared from the corresponding fluoride by metallothermic reduction techniques previously described by Daane.4 The chemical analyses of the metals used are listed in Table I.

Jan 1, 1965

This report presents the results of reconnaissance-level investigations of the mill refuse disposal systems for 15 plants throw-heat the conterminous United States. The sites visited represent a cress section f the copper, iron, lead and zinc, and phosphate industries' practices in the field of fine-grained refuse disposal. The reconnaissance-level investigations were carried out to gather supplemental data to tae in-depth studies of Kennecott's Magma and Phelps Dodge's Morenci tailings deposits and Kennecott's Chino leaching dump. The various sites visited were classified according to the different systems and techniques used by the mining industry. The probable effects and relationships between site conditions and disposal methods were determined and evaluated to the extent feasible by a reconnaissance level investigation.

Jan 1, 1974

By C. Froger

Since its creation in 1950, the Centre d'Etudes et Recherches des Charbonnages de France at Verneuil-en-Halatte (Oise) has been conducting many investigations concerned with airborne dust measurements, particularly in underground mines. The work has resulted in the development, a few years ago, of a new process of dust sampling, whereby the airborne dust particles are collected by a rotary filter of polyurethane foam rotating at high speed within 8 housing.

Jan 1, 1973

By E. G. Davis

This report summarizes an investigation to determine the occurrence and recoverability of heavy minerals in sand and gravel operations in the Southeastern United States. A total of 61 samples from 34 sand and gravel operations in Alabama, Georgia, South Carolina, and North Carolina were studied. Heavy minerals, in amounts ranging from 3 to 400 pounds per ton, were found in all of the samples. Eighty percent of the samples contained 20 to 40 pounds per ton of heavy min¬eral. Valuable heavy minerals, in order of decreasing amounts, were ilmenite, kyanite, zircon, rutile, and monazite. Large-scale concentration tests were made on five samples from four major producers. Gravity concentration by Humphreys spirals and tables resulted in bulk heavy mineral concentrates that graded from 82 to 98 percent total heavy minerals. Mineral recoveries ranged, in percent, as follows: Ilmenite 60 to 95; zircon 96 to 100; kyanite 37 to 77; rutile 89 to 100; and monazite 96 to 100. Separation studies on the gravity concentrates showed they would respond to high-tension and high-intensity magnetic separation techniques to produce individual mineral concentrates. The recovery of each individual mineral from fractionation of the heavy mineral gravity concentrates, in percent, was: Ilmenite 77 to 94; rutile 41 to 68; kyanite 62 to 79; zircon 49 to 83; and rare-earth products, monazite and xenotime, 42 to 96. The grade of each mineral concentrate was: Ilmenite 51.1 to 68.7 percent Ti02; rutile 93.7 to 94.3 percent Ti02; kyanite 55 percent A1203; zircon 58 to 61 percent Zr02; and rare-earth products containing 73.8 to 90.8 percent monazite and 4.8 to 12.7 percent xenotime.

Jan 1, 1971

By J. C. Gerdeen

This project was a supporting effort with research contract H0230016 at White Pine Copper Company. Creep properties of White Pine rock were determined. These and properties for bolted joints were used in finite element analyses of sections of the White Pine Mine which included analysis of bed separations in the roof and sloping faults. In-situ experimental measurements were made of tension, compression, and bending of resin bolts by use of strain-gaged bolts. Evaluations of bolting effectiveness and comparisons of predicted and measured roof behavior are given.

Jan 1, 1976

By Toshiharu Teranishi

When we apply the Au nanoparticle superlattices to the future nanooptical and nanoelectronic devices, the control of not only the particle size but also the interparticle spacing and symmetry of superlattice are the essential problems to be overcome. First, we developed a novel synthetic procedure to precisely control the particle size of alkanethiol-protected Au nanoparticles in the range from 1.5 to 9.7 nm by the heat-treatment of the small Au nanoparticles in the solid state. Absorption and nonlinear optical properties of alkanethiol-protected Au nanoparticle superlattices were then elucidated. On the other hand, the hexagonal close-packed (hcp) 2D superlattices of small Au nanoparticles with the interparticle spacings from 1.9 to 3.6 nm were successfully prepared by using newly-synthesized ligand for single electron tunneling devices. Finally, various symmetric superlattices, such as chain (2-fold), quasi-honeycomb (3-fold), square (4-fold), etc., of Au nanoparticles could be produced by making use of interligand interactions or some templates.

Oct 1, 2003

By Michael S. Miller

In 1987 and 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 3,100-acre Borah Peak Wilderness Study Area (10-047-004) and a 708-acre parcel adjacent to the north in order to evaluate their identified mineral resources. The study area is located in Custer County, ID, about 18 mi northwest from MacKay. The study area lies along the western foothills of the Lost River Range and is underlain by quartzite, sandstone, shale, argillite, dolostone, and limestone. The Lost River fault, a major active fault, lies along the length of the study area. Large alluvial fans spread out from valleys originating east of the study area.

Jan 1, 1989