Search Documents

By D. R. Wilburn

The worldwide budget for non fuel mineral exploration was expected to increase by 27 percent in 2003 from the 2002 budget, according to the Metals Economics Group (MEG) of Halifax, Nova Scotia. The increase comes after five years of declining spending for mineral exploration. For the first time in several years, all regional exploration budget estimates for 2003 as defined by MEG would increase from similar 2002 estimates. However, MEG included 193 more companies in its 2003 survey than in 2002. As with previous MEG survey reports, estimates reflect anticipated expenditures rather than actual dollars spent. Caution, therefore, must be taken when comparing 2002 and2003 estimates or evaluating the magnitude of regional changes from year to year. Sample variations and currency exchange rates may influence year-to-year variations of MEG data. Even so, it is likely that the general climate of improved metal prices in 2003 encouraged companies that had previously left the mineral exploration sector or reduced their exploration activity to once again focus on minerals exploration or increase exploration activity and budgets.

Jan 1, 2004

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele 'Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

By T. A. Kirk

"The Linatex Dewatering System is a compact, low capital and maintenance cost matched set of processing equipment suitable for solids recovery, dewatering and desliming sand-like materials in the range 3/8"" to 325 mesh ( 1). Since its introduction to North America in the early 1970s, various elements of the system have been successfully installed in a variety of applic11tions both in Canada and the U.S.A. Examples are chosen from the coal, fine aggregates, iron ore and industrial minerals industries.II. Elements of the Linatex Solids Recovery System(A) The Linatex Separator (See Fig.I)The Linatex Separator, which is the heart of the system, is a specialized type of hydrocyclone designed to give a self regulating rope discharge product. It has the familiar cyclone geometry of cylindrical and conical section, tangential inlet, apex and vortex finder. The apex is enclosed in a unique patented automatic underflow regulator consisting of a collapsible rubber sleeve, and the overflow line is a siphon-leg, with a controlled air bleed valve. The siphon leg is adjusted so as to balance the internal negative pressure acting as a closing force on the underflow regulator against the mass of slurry pressing down on it from the cone section of the Separator. With correct adjustment the underflow regulator will close drip-tight on a water only feed. As solids accumulate in the apex of the cone the weight of solids counterbalances the vacuum and cat1ses the underflow regulator to open and discharge classified material at a controlled density."

Jan 1, 1978

By Dong G. Chae

A model for the leaching of oxide ores is developed and II correlated with laboratory tests for percolation leaching of copper oxide are. Using the model, recovery of metal values and lixiviant concentration of the effluent solution at any time may be evaluated. For the copper oxide ore a simplified version of the model is examined for the leaching mechanism consisting of: 1) a surface flush reaction with the highest rate of lixiviant consumption; 2) penetration of lixiviant to react with copper minerals and gangue constituents; and, 3) slow lixiviant consumption, mostly by residual gangue materials. The simplified model is able to explain reasonably the leaching behavior of copper oxide ore by introducing a concept of effective initial size to correct for packing in a bed of fine particles.

Jan 1, 1979

This document is Volume II of a two-volume report on underground and surface coal mine fires occurring between 1950 and 1977. Volume I discusses the methods of data acquisition, data analysis procedures, results and conclusions. This volume contains (1) a master list of all fire incidents obtained from MSHA reports, (2) an annotated bibliography of all MSHA reports, journal articles on selected incidents, and non-reportable fires (appendix), and (3) indexes to be used in accessing incidents in the master list and annotated bibliography. These three types of information provide the reader with a complete summary of coal mine fires during the period from 1950 through 1977 and a convenient means to locate incidents of specific interest. The body of this volume is organized around two tables and a series of indexes. The two tables are master lists of underground and surface fire incidents. They are followed by 14 indexes keyed to the master list and annotated bibliography. The appendix contains three different parts: o The annotated bibliography of MSHA fire reports (one section each for underground and surface mine fires) o The annotated bibliography of journal articles about selected fires from the MSHA bibliography o A listing of non-reportable fires (one section each for underground and surface mine fires) Descriptions of the contents and use of each of the three major components of this volume (i.e., master list, indexes, and appendix) are presented in Section 2.0.

Jan 1, 1979

By Alexander May

The Bureau of Mines conducted studies to determine if phosphogypsum, a waste material from the processing of phosphate rock, contains hazardous toxic materials as defined by the Environmental Protection Agency (EPA) and whether leaching of these toxic materials and radium may occur. Samples of the phosphogypsum stockpiled material were evaluated using the EPA extraction procedure, atomic absorption, neutron activation, x-ray diffraction, and chemical and physical means. Radiological tests performed used both the germanium-lithium and emanation methods. The data show that the phosphogypsum stockpiles are not hazardous toxic waste as defined by EPA criteria. Trace elements and radium are not leached from the phosphogypsum stockpiles. Absorption of trace elements and radium by phosphogypsum is the major reason for their not being leached. The standard error of measurement of radium concentrations was 4.7 pCi/g.

Jan 1, 1983

By Stephen D. Smith

The following tables summarize data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in these tables is what is termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines. Because of inadequacies in the statistics available, some series deviate from the foregoing definition. For copper, gold, lead, silver, tin, and zinc, the quantities are recorded on a mine basis (as the recoverable content of ore sold or treated). However, the values assigned to these quantities are based on the average selling price of refined metal, not the mine value. Mercury is measured as recovered metal and valued at the average New York price for the metal. The values shown are in current dollars, with no adjustments made to compensate for changes in the purchasing power of the dollar.

Jan 1, 1995

By Seppo Haapamaki

"Since it started production in 1970, Anderson Lake Mine has experienced several radical changes in mining methods as a result of the physical characteristics of the ore zone along with the need for improved productivity. This paper examines the transition from longhole open stoping to mechanized cut-and fill then to vertical crater retreat at Anderson Lake Mine. The reasons for the need to change mining methods is analyzed taking into consideration the impact of such criteria as improved productivity and ground conditions and how these criteria affected the over-all economic viability of the mine. IntroductionAnderson Lake Mine is one of five producing copper mines in the Snow Lake area and is situated approximately 3 km southeast of the townsite of Snow Lake (Fig. I).The mine production rate at Anderson Lake is 700 tpd and all ore is trucked from the mine to the mill located approximately 2.5 km from the mine site . The mine is serviced by a three-compartment shaft sunk to a depth of 3300 ft with level spacings at 175 ft and 150 ft intervals from the 600 ft level to the 3000 ft level. .The shaft was collared in 1965 and, a year later, the hoist and compressors were installed. By 1969, a crusher system had been built and actual production began in 1970. During 1978, production was suspended for the year to allow for 430 ft of shaft deepening."

Jan 1, 1988

By A R. Penney

Since mining-induced seismicity first became apparent at the Beaconsfield Gold Mine in 2002, there has been an ongoing program of geotechnical investigations to understand the phenomenon and allow for the development of strategies to manage the risks it posed to personnel, the business and the community at large. Studies resulting from a seismically induced rockfall on Anzac Day 2006 have been extensive, and have advanced the understanding and management of seismicity at the mine. Enhancement of the mineÆs seismic array, implementation of extensive monitoring of ground behaviour, improved ground support and reinforcement design, and ongoing numerical modelling provide a technical framework for the management of seismicity. In addition, extensive involvement of the workforce in risk assessment and the development of standard work procedures (SWPs), has contributed to a æbest practiceÆ approach to manage seismic hazards at the mine.

Jan 1, 2008

By Jacques Ouellet, Ferri Hassani

"Within the mining industry paste backfill technology has evolved over the last two decades. This technology aims at producing safe and cost effective backfill of high strength. When used as cemented backfill underground the usual practice in the mining operations was to consider the backfill as a component under the production engineer responsibility. With its growing use in various site conditions some problems were encountered. Over time the mechanical characteristics of paste backfill could deteriorate. Investigations on these problems brought an increased understanding of paste backfill chemistry. Effectively, paste backfill is produced with tailings slurry having sometimes very complex chemistry and mineralogy. The bonding agents can be sensitive to the chemistry of these slurries. Today, a new understanding of the complex chemical reactions involved in cementing paste backfill is derived from concrete research literature. Cemented paste backfill is a manufactured product and as thus all steps involved in its making must be looked at. Both the processing engineers and mining engineers need to be involved. The proposed paper will go over the various developments and new understanding gained over the years on paste backfill chemistry. The authors had the opportunity to work with various Canadian mines that implemented paste backfill in their operations. Chemical alterations case study will serve to illustrate the importance of a good understanding of cement and paste chemistry. The authors will then conclude on research orientations needed to bring a more efficient use of paste backfill technology. The crucial role of the processing engineers in the paste backfill manufacturing will be discussed.INTRODUCTIONPaste backfill is usually prepared from a mixture of solids and water containing at least 15% particles smaller than 20 microns with the addition of binders for mechanical strength. Historically, tailings had been classified to extract the fines and only the coarse part was placed underground as sand slurry. Paste fill was researched in the last three decades to enable mining operations to use all the tailings, including fines, in backfill. The outcome of the early studies showed that paste fill provides high strength but due to preparation complexities and transportation problems is expensive. A greater understanding of the transportation mechanisms and advances in dewatering technology in recent years has resulted in more practical use of paste backfill."

Jan 1, 2002

This work examined the feasibility of in-mine coal preparation in two phases. Phase I included a survey of previous investigations and a preliminary analysis of the economic and technical feasibility on a selection of representative sites and degrees of cleaning. The contract was terminated at the end of Phase I. The preliminary analysis determined that in-mine preparation systems can be applied using currently available technology. The most likely mines for application will have shaft or slope access and be deeper than 500 feet. The refuse disposal systems technically feasible are (1) pneumatic placement of coarse refuse in room and pillar panels or longwall faces, (2) mechanical placement of coarse and fine fractions in room and pillar panels, and (3) hydraulic placement of fine fractions in room and pillar panels. The economic feasibility is much more dependent on the refuse disposal-system than on the preparation system. It is estimated that the capital cost of an in-mine preparation and disposal system would be $6.00 per clean ton and the operating cost would be $1.24 per clean ton for a 1 million clean ton per year mine.

Jan 1, 1982

By Paul C. Hyndman

No minerals have been produced from the McGraw Creek RARE II area. During the 1982 U.S. Bureau of Mines study, there were no active mines in the area. Limestone occurrences (fig. 1, no. 2), four copper prospects (fig. 1, no. 1, 4, 5, 6), and a prospect with no significant mineral values (fig. 1, no. 3) were examined. A moderate potential for high-calcium limestone resources was estimated between ocurrences within the study area near McGraw and Spring Creeks (fig. 1, no. 2). There is low potential for copper resources at the Argenta Prospect (fig. 1., no. 1) in the study area, and the McDougall Prospect adjacent to the area.

Jan 1, 1983

By E. P. Carman

1. DAVENPORT, S. J. Bibliography of Bureau of Mines Publications Dealing With Health and Safety in the Mineral and Allied Industries, 1910--46. Tech. Paper 705, 1948, 154 pp. 30 cents. 2. FJELDNER, A. C., FISHER, P. L., AND POLLOCK, M. B. Bibliography of Bureau of Mines Investigations of Coal and Its Products, 1940 to 1945. Tech. Paper 698, 1947, 53 pp. 15 cents. 3. GOOD, J. E., ABREU, ALVARO, AND FRASER, THOMAS. The Coal Industry of Brazil. Part 1. General Economy, Production, and Marketing. Tech. Paper 713, 1949, 38 pp. 20 cents.

Jan 1, 1954

By D. G. Bishop

This paper is intended as a review and update of the use of Pressure Injected Footings as deep foundation units in North America. We will discuss various aspects of this pile and then discuss a particular project - the Mobile Alabama Convention Centre which is currently under construction. Pressure Injected Footing is a generic name used to describe a foundation unit that has been in use around the world for some 80 years. It has been used on all types of structures. It is an excellent pile in both compression and tension. It is particularly economic where a layer of granular soils can be found at relatively shallow depths. Other types of piles would penetrate these layers. Caissons are often difficult to construct in these soils because of their lack of cohesion and the often present water table. PIFs can density these shallow layers and carry relatively heavy building loads on them.

Jan 1, 1992

By William M. Hinton

This report describes the approach, procedures, and results of a program to develop training materials for roof bolter operators. The objective of the program was to design and produce a training sequence which would prepare roof bolter trainees for job performance. Data was collected and analyzed using the general procedures of Instructional Systems Development (ISD). Input data came from a previous roof bolter training analysis program. This data was expanded and structured through a series of ISD steps: objectives hierarchies, media selection, syllabus, lesson specifications, and train¬ing materials development. The resulting program consisted of an ordered sequence of 15 lessons. The media mix for the 15 lessons included lectures, slide-tape lessons, and hands-on instruction using operational roof bolters. Contents of all lessons were reviewed and approved by the Bureau. The key recommendations were to (1) validate the materials and measure relative effectiveness of media formats; (2) survey mines for training resources and conditions - match materials to user capabilities, rather than selection state of the art technology/media; (3) develop job performance aids (JPAs) rather than simulators; (4) create a style/media/JPA development guide for use in future projects of this kind.

Jan 1, 1982

By G. M. Kintz, Charles B. Carpenter, G. W. Jones

"INTRODUCTION At 9:12 a. m. on April 16, 1947, the ammonium nitrate cargo in hold 4 of the S. S. Grandcamp, a 7,176 gross-ton Liberty ship owned by the French Government, detonated at pier 0 of the Texas City Terminal Railway Co., Texas City, Galveston County, Tex.This detonation was the first of a series of explosions and fires that took the lives of approximately 600 persons, injured 3,000 other persons, and caused a property damage and business loss that will exceed $58,800,000. It has been estimated that the life, accident, and workmen's compensation insurance loss will be $8,200,000.At 1:10 a. m. on April 17, 1947, the ammonium nitrate cargo in hold 5 of the S.S. High Flyer, a 6,214-gross-ton Liberty ship owned and operated by the Lykes Bros. Steamship Co., Inc., detonated at pier L. This explosion materially increased the property damage caused by the first explosion, in between 50 and 100 persons, and is believed to have taken the life of only one person.The exact number of casualties resulting from the Texas City disaster may never be known. On June 22, 1947, 65 days after the explosions, the red Cross and the Texas Department of Public safety repoted:,""Identified dead, 405; unidentified dead, 63; believed missing, 100; injured, 3,000; hospital¬ized, 600; still in hospitals, 37."""

Feb 1, 1948

By A. Hotta

Reduction of CO2 emissions is the key driving force behind the development and implementation of new solutions for energy production. One solution is circulating fluidized bed (CFB) combustion technology combined with a high-efficiency once-through water-steam cycle. Foster Wheeler's CFB technology is today commercially available in capacities up to 800 MWe with ultra-supercritical steam parameters. Simultaneously, the Flexi-Burn® CFB technology is being developed to provide capability of flexible operation in air firing and oxy-combustion for carbon capture. CFB technology can offer an attractive solution for the reduction of CO2 emissions, owing to advantages such as fuel flexibility and low emissions that the air-fired CFB technology offers today. Pilot test facilities provide information about the performance of CFB oxy-combustion technology, and the acquired knowledge is being incorporated in boiler modelling and design tools. One of the European R&D initiatives on carbon capture and storage (CCS) is the Technological Centre for CO2 Capture and Transport, which is supported by the Spanish Government through the Fundación Ciudad de la Energía (CIUDEN). CIUDEN is a research and development institution created by the Spanish administration in 2006 and fully conceived for collaborative research in CO2 capture, transportation, and storage. The Technology Development Centre for CO2 Capture and Transport comprises two technologies on oxy-combustion: pulverized coal (PC) and circulating fluidized bed (CFB). This paper will focus on the design and main characteristics of the 30 megawatt-hour thermal capacity (MWth) oxy-CFB boiler. Foster Wheeler is the technology provider of the Flexi-Burn CFB unit, for which commissioning has been completed in the first quarter of 2011. The CFB unit design allows operation either under conven¬tional combustion with air or under oxy-fuel conditions. The size of this experimental boiler is sufficient to allow the scaling of the results to commercial units. In this way, multiple fuels and operating conditions can be tested economically. The results will validate the design of a future 330 MWe supercritical Oxy-Combustion Power Station (OXY-CFB-300 Compostilla Project) intended to demonstrate the CCS technology at commercial scale. The Compostilla OXY-CFB-300 Project is one of the six CCS demonstration projects funded under the European Energy Programme for Recovery (EEPR) of the EU. The project is based on a future 330 MWe CFB supercritical oxy-combustion plant, with CO2 storage in a deep geological formation. The first phase of the project, granted by the EEPR programme and led by the Spanish utility ENDESA, includes all studies and characterization work needed on CO2 capture, transport, and storage, as well the costs, financing, and regulatory and permitting required, prior to the final investment decision for the construction phase of the plant by the end of 2012.

Jan 1, 2012

By M. C. Bleiweiss

Various light sources were evaluated for use in a fiber optic lighting system for mining machines. It was determined that a metal halide arc lamp was best because of its resistance to damage from shock and vibration and the high luminance of the arc. Measurements were made of the percent transmission of the ½ inch thick glass window and the fiber bundles, the total lumen output of the diffuser assembly with a known input and of the average surface luminance of the diffuser assembly. These data were then used to calculate the theoretical output of the system given an estimated input from the source. A prototype 55 watt, single-ended metal halide source was then developed. In order to provide greater efficacy and higher throughput through the fiber optic cables, a variation of the lamp with thallium iodide added to the fill was developed. The lamp was modified and a ballast was developed to allow it to hot restrike.

Jan 1, 1986

By Arthur F. Taggart

THIS paper proposes two units (believed to be new) for designating, respectively, capacity and efficiency for primary and intermediate crushers. CAPACITY Operators know that the tonnage of rock that can be put through a particular crusher in a given time depends primarily upon the crusher setting (open setting for jaw and primary gyratory types; closed setting for cones and rolls), and secondarily on the lithological character of the feed, its maximum size, the amount of fines that it carries, its moisture content, and the method of feeding. The proposed capacity formula states a relationship between all of these factors in one empirical equation, as follows: TR = TR80KK'K" [I] in which TR, called "reduction tons per hour" is the new capacity unit; T = tons of feed per hour requiring crushing; R50 = "80-per cent reduction ratio"; and K, K', and K" are constants that approximate quantitatively lithological character, moisture content and method of feeding, respectively. T is the hourly weight of material in the feed that is coarser than the coarsest discharge of the crusher. (For marked departures from the normal specific-gravity range-2.5 to 2.7-T should be adjusted to corresponding volumes.) In the crushers under consideration, discharge from the crushing zone is limited by the minimum dimension of a particle. Passage of the particle through a square-mesh screen is limited by its intermediate dimension. Sheppard' has shown that the ratio of maximum: intermediate: minimum average dimensions of broken rock fragments may be taken as about I.5: I: 0.6 for nonslabby rocks such as are normally crushed, while for slabby rocks, such as thin-bedded sedimentaries, foliated schists and gneisses, and the blocky metamorphics, the ratio is of the average order I.3:I:0.3, with the possibility of an even smaller relative value for the thickness. Gaudin2 finds the corresponding ratio for -150 + 200-mesh pyrite to be I.4: I : 0.6. The hourly tonnage of crusher-plant feed, therefore, should be diminished by the amount thereof that would pass a square-mesh screen of which the aperture is S times the crusher setting, where S is a shape factor with the value I.7 for rocks that break exceptionally cubic; 2 for ores and rocks that exhibit no appreciable tendency to slabbiness; and 2.5 to 3, or, in exceptional cases, even larger, when the tendency to slabbiness is marked. R80 is the quotient of the theoretical square-mesh aperture that would pass 8o per cent of the feed, divided by the aperture that would pass S0 per cent of the product. It is best determined from screen tests.

Jan 1, 1941

By F. Pagliacci

Retaining walls for the construction of underground urban infrastructures have to be executed considering the impact of a deep foundation job-site within an urban network. Traditional excavation systems, based on the use of grabs and bentonite mud, involve serious problems such as: the opening of trenches adjacent to existing buildings; the cleaning of the working area; the site installation for the production and storage of the bentonite mud; the transport and disposal of soil contaminated with bentonite mud. Alternative solutions have therefore been developed in order to overcome these problems. For temporary works soil consolidation methods, combined with the use of sheet piles, have been implemented, by a combination of traditional mixing methods and jet grouting systems to speed up the operations, consequently reducing the construction time. For permanent works two new techniques named respectively CSP (Cased Secant Piles) and CDW (Continuous Diaphragm Walls) have been studied, applied and tested.

Jan 1, 2000