Search Documents

By Aly M. Mohammad

State and federal agencies during rehabilitation of existing bridges may require the existing bridges to be evaluated under seismic conditions. If the bridge does not perform under the seismic event, the bridge may require seismic retrofitting. Bridges are classified as: Critical, Essential, and Others according to their importance. Geotechnical considerations play a major role in evaluating the bridge behavior under a seismic event. Subsurface conditions influence the magnitude of ground acceleration and hence the forces and moments on the superstructure. This paper will provide a detailed description of the geotechnical aspects associated with the seismic retrofit evaluation for the 12th Street and 14th Street Viaducts located in Jersey City, New Jersey. The paper will also present a description of the geotechnical investigation program including seismic cross-hole surveys to determine the dynamic soil parameters, including the results of site-specific response spectra for both the 475 and 2475-year events. Liquefaction assessment methodology utilizing an equivalent factor of safety will also be described and the design method used will be summarized. In general, the pile foundation is modeled as 6x6 foundation stiffness matrix with 36 stiffness coefficients at the center of the pile cap. The seismic loading on the foundation is evaluated in a pseudo-static analysis, where the dynamic earthquake-induced loads are presented by static forces and moments. The computer program FB Pier was used to evaluate the foundation stiffness. The moments, axial loads, and shear are input into the FB Pier model. The stiffness of the foundation is determined and the results are then input into the Structural model to determine new forces and displacements. Adjustments are made until the loads are compatible with the stiffness used. The understanding of the geotechnical conditions at the 12th Street and 14th Street Viaducts and the coordination between the Bridge and Geotechnical Engineers were able to provide significant cost saving to the Owner. The Design Engineers were able to retrofit the existing Viaduct foundations with reasonable number of additional piles. It is believed that the results and finding presented in this paper will benefit both the Bridge Engineers and Geotechnical Engineers by highlighting the importance of interaction between the two disciplines.

Jan 1, 2006

By L. M. Lenahan, J. D. Sheets

INTRODUCTION The Raleigh-Durham International Airport (RDU) in North Carolina is the fourth largest airport in the southeast region of the United States. The Raleigh-Durham Airport Authority is currently underway with planning, designing and constructing are placement Passenger Terminal as part of the Major Capital Improvements Program at Raleigh Durham International Airport. The Terminal C Expansion and Renovation Project will replace the existing Terminal C structure with a new processor building and concourse. The project is separated into several contracts. The early stage contracts are constructing a west side storm water management facility, relocating taxiways, installing new drainage systems, installing new aircraft apron pavement, Demolition, the Central Energy Plant and Early Foundations. The later projects are the Terminal Building, Passenger Boarding Bridges, Information Technology Systems and Integration, Furniture, Furnishings & Equipment and Specialty Millwork. The Terminal Building will be constructed in two phases. Phase 1 constructs the north half of the new terminal. Airline operations will move to the new terminal at the completion of this phase. Phase 2 completes construction of the south processor building. The full build out of the project, subject to funding availability, will replace the remainder of the south concourse. The Program’s primary focus is to replace the existing passenger Terminal C with a new terminal that will provide more passenger gates and larger passenger screening, ticketing and baggage handling facilities. The planning for the New Terminal C Program began in 2002 with construction starting in March, 2003. The continuing growth of passenger airline travel in the Raleigh/Durham metropolitan area requires RDU to expand its facilities to keep up with the present and future growth within the Region. In October of 2002, the RDU Airport Authority selected Parsons Transportation Group as the Program Manager/Construction Manager to help assist in the development of the Terminal C expansion program. RDU Airport Authority selected the Seattle Washington Office of URS Corporation as the Engineer of Record for the West Side Storm Water Management Facilities. The Westside Storm Water Management Facilities Project became one of the early critical path activities of the overall RDUAA Terminal C Expansion Program. The Briar Creek Reservoir had been constructed to accommodate storm water runoff to the west of the Airport. The existing 1.5 m culvert that drained runoff from the airport terminal (area) to the reservoir was insufficient in supporting the additional flows

Jan 1, 2005

By J. Chae, D. Pecha, R. Andrews

The Henderson/ML King CSO Project is a major combined sewer overflow (CSO)reduction project for the Department of Natural Resources and Parks of King County, Washington. The central element of the project is the 3100 lineal feet long, 14'-8"diameter 42nd Ave S Storage/Treatment Tunnel. During the course of the project, the owner and consultants evaluated numerous elements of the tunnel including the alignment, geotechnical conditions, tunnel liner, and settlement monitoring requirements. The contractor utilized innovative shaft construction methods for the tunnel portals, and adhered to strict contract requirements in successfully constructing the tunnel. This paper provides an overview of the design and construction elements of the 42nd Ave S Storage/Treatment Tunnel that led to the successful completion of the project.

Jan 1, 2005

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009

By P R. L Browne

Study of geothermal systems in the Taupo Volcanic Zone (TVZ) has significantly advanced our understanding of the processes of epithermal mineralisation. The three main lessons learnt are: 1. knowledge of their chemical anatomy; 2. precious metal transport and deposition; and 3. hydrothermal alteration zoning. These are described in the context of ore formation and exploration.

Jan 1, 1997

By Keith Jones, Michael Francis

Contract 240 of the Channel Tunnel Rail Link comprises construction of twin4.7 km long running tunnels through a densely populated area of East London. The tunnels were constructed by EPBM in Sands and Sandy Clays, passing 4.4 m below the existing London Underground tunnels, and at depths of 20–30m below ground level beneath the Great Eastern railway lines into London Liverpool Street and a series of railway bridges and hundreds of buildings. This paper describes how the project team managed the challenges relating to the issue of settlement: mitigating settlement effects, prioritising the structures to be assessed, controlling resource expenditure by incentives and flexible response to urgent work relating to unforeseen events such as ground collapse and discovery of unusual structures.

Jan 1, 2005

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

Reconnaissance geochemical exploration in the vicinity of low angle detachment faults which bound the core of the Paparoa metamorphic core complex yielded Au up to 14 ppm, with 35% of greywacke, granitoid and quartz vein samples in the northern range exceeding the 0.01 ppm detection limit. Au is associated with Ag, As, Sb and Cu anomalies consistent with epithermal-type mineralisation. The Ag and Cu anomalies also distinguish this mineralisation from older, mesothermal Au deposits widespread in the Ordovician &apos;slate belt&apos; greywackes, which comprise much of the upper plate of the core complex. Baryte, molybdenite, fluorite and stratiform U mineralisation in the northernPaparoa Range may also be related to hydrothermal activity along the detachment fault zones.

Jan 1, 1995

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By P. van der Heever

The genesis of Simrac?s technology transfer practices and future initiatives are discussed in this report. Simrac produces a relatively large volume of research-based health and safety outputs that must be communicated to its tripartite stakeholders and to other interested and affected parties. The wide spectrum and complexity of the transferables, together with the diversity of end-user needs and skills of the recipient population, necessitate customizing of technology transfer practices. In an attempt to optimize this process, a variety of practices are employed. Information is transferred by means of publication and dissemination of a variety of reports (paper, website and CD).Knowledge transfer is directed to health and safety practitioners by means of workshops, seminars, best practice booklets, handbooks and textbooks. Promotion of recently completed projects is directed at targeted recipients by means of project launches. Only isolated cases of piloting and implementation of technologies have been undertaken due to lack of resources and past organizational focus. It is anticipated that Simrac?s new organizational structure and management system, together with end-user involvement by industry champions, from project inception to implementation, will enhance the effectiveness of the technology transfer process.

Jan 1, 2002

By M. D. Khattar

Problems discussed concern encountering of high temperatures [up to 66°C] and heavy flow of water [150 L.P.S] during the construction of the 10.15 MØH.R.T. for the 2500 MW Nathpa Jhakri Hydro Power Project in the Himalayas(India). Over a length of 2500 M progress of work got seriously affected resulting in excessive time for completion - two years [max. monthly progress achieved was 178 M [Heading]. Many innovative and simple steps were taken to complete the work in these inhospitable environs affecting working of both men and machines. Also it meant a review of the design of concrete lining. Other geological conditions affecting the progress are also described.

Jan 1, 1999

By Deno Pappas, Chrisropher Mark, John Rusnak, Linda McWilliams

Mine planning for a new reserve is based on information obtained from exploratory coreholes. A critical component of an exploration program is the geotechnical evaluation. Poor assumptions about roof conditions greatly add to the risks of mining. Rock mechanics testing is central to a geotechnical exploration program. Typically, 3 to 5 uniaxial compressive strength (UCS) tests are made to characterize a particular roof unit at a given corehole. The average (mean) of these tests is taken as “The UCS” for that location. Isopach contour maps are then used to show spatial trends in roof strength. Two issues are raised by this traditional approach. The first is due to the large variability in UCS values that is typical even within a single unit from a single hole. The average UCS might be higher at Corehole A than it is at Corehole B, but the difference may not be statistically significant. The second issue is whether widely spaced coreholes can identify valid spatial trends in rock strength. The answer depends upon whether rock strength changes over distances that are longer or shorter than the corehole spacing. This is a classical geostatistical problem. While geostatics have been used to investigate many coal quality parameters, they have seldom been used to evaluate rock strength. This paper describes an extensive investigation of these issues conducted by the National Institute for Occupational Safety and Health (NIOSH) in collaboration with Peabody Energy. The study employed the Peabody Rock Mechanics Data Base which contains more than 10,000 individual test results. Data from four important roof units were subjected to statistical analysis: • Brereton Limestone above the Herrin 6 seam (Illinois) • Turner Mine Shale above the No. 9 Seam (Kentucky) • Sandstone above the Eagle Coal (West Virginia) • Shale above the Eagle Coal (West Virginia) The study did not find significant spatial trends in rock strength in any of the cases. Perhaps there are none, or perhaps the exploration coreholes were just too far apart to see them. These results have valuable implications for the design of geotechical exploration programs.

By C. Taschereau, G. A. Vickell, A. R. Laplante

Evidence in support of an iron-gold corrosion cell during the high-temperature/highpressure elution of loaded carbon is presented herein including, but not limited to, its discovery, mode of genesis, and confirmatory laboratory testwork. A discussion of metallurgical and economic impacts, remedial investigations, plant design considerations, and future work including mitigative possibilities is presented.

Jan 1, 2006

By L. Kulik, J. den Drijver

Rhenish lignite will continue to play an indispensible role in the energy mix of the German Federal Republic for a long time to come. The use of lignite for electricity generation, upgrading and, if necessary, as a raw material is geared to the long term. The holistic management of opencast mines underpinned by approval law in the long term and a stronger focus on man, the environment and nature contribute to the acceptance of the mines by the local population. The same is true of state-of-the-art lignite uses: as regards their operational flexibility, lignite-fired power plants are ideal partners for the expansion of renewables. It is along these lines that RWE is continuing its power plant renewal programme as planned. With a view to that which will be conceivable the day after tomorrow, RWE is researching future technologies today in order to meet objectives such as security of supply, profitability and environmental compatibility to the same extent in the long term. Another important contribution to acceptance is public transparency and communications as means to support approval procedures and the implementation of measures in all areas related to lignite mining and utilization.

Jan 1, 2011

The Effect of Molecular Weight on the Adsorption and Efficacy of Polysaccharide Depressants

Sep 13, 2010

Drill cores from Section 62, New Broken Hill Consolidated Ltd., were used to study the petrology of rocks associated with the zinc lode. The distribution of the rock types in relation to the lode structure was determined. The distribution of the gahnite-bearing rocks was shown to be only partly conformable with the structure.It was concluded that large scale metasomatism was not widespread, that the rocks associated with the lode (except, perhaps, the quartz-gahnite-garnet rocks) were formed by metamorphism of sediments, and that rocks and lode were contemporaneously metamorphosed.INTRODUCTIONThis investigation was undertaken in order to study the rock types associated with the zinc lode of the Broken Hill orebody, and their relationship to the structure of the ore horizons. The work was confined almost entirely to the laboratory, and is therefore limited in its scope. It is hoped, however, that the information gained may throw some new light on the genesis of the lode.Certain inferences which are drawn from this work are at variance with the ideas of a number of earlier workers.In particular, the idea of large scale metasomatism developing many of the rocks associated with the lode, especially those containing manganese, is questioned. On the contrary, the rocks associated with the lode are more simply explained as highly metamorphosed sediments, in some cases modified by water introduced from surrounding rocks into zones of strong folding and faulting. As a corollary, a metamorphicsedimentary origin for the lode material, either as a concentrated sulphide deposit, or somewhat disseminated...

Jan 1, 1961

New York Meets first Wednesday after first Tuesday of each month. J. E. JOHNSON, JR., Chairman EDGAR RICKARD, Vice-Chairman D. M LIDDELL, Secretary, 7 Wall St., New. York, N. Y C. A. BOHN, Treasurer JOHN V. N. DORR _ LEWIS W FRANCIS Boston Meets first Monday of each winter month. R. L. AGASSIZ, Chairman - JAMES G. CARLETON, Vice-Chairman E. E. BUGBEE Secretary-Treasurer, Mass. Inst. of Technology, Cambridge, Mass. W. E. C. EUSTIS G. A. PACKARD Columbia Holds four sessions during year. Annual meeting in September or October. S. S. FOWLER, Chairman J. C. HAAS, Vice-Chairman LYNDON K. ARMSTRONG, Secretary-Treasurer. P. O. Drawer 2154, Spokane, Wash. W. H. LINNEY

Jan 2, 1918

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010

By J. Cayouette

In 1995, Louvicourt mine started one of the first paste backfill operations in Canada. From 500 000 t in 1995, the annual paste backfill tonnage produced reached 800 000 t in 1999. The maximum throughput of the surface plant (including binders) is 3500 tpd with a final density of 75% to 76% solids which gives a slump of 15 cm to 17 cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders in a mixture of 20% cement to 80% ferrous slag. In certain stopes, the binder ratio may vary from 2% to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5 Mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.

Jan 1, 2003

By W. C. Ellis, E. S. Greiner, M. E. Fine

Discontinuous changes of Young&apos;s modulus, internal friction, coefficient of expansion, electrical resistivity, and thermoelectric power are evidence for a transition in chromium near 37OC. Although the X-ray diffraction pattern gives no clue, a difference between the thermal expansivity and the temperature dependence of the lattice parameter suggests a crystal-lographic change. Young&apos;s modulus data disclosed another transition near THE thermal dependence of a number of proper- ties of chromium indicates a transition occurring over a temperature range near room temperature. Bridgman&apos; noted this first from a minimum in the electrical resistivity near 12°C. In a sample of greater purity, Sochtig&apos; observed the minimum at 41 °C. Erfling3 reported an inflection in the thermal expansivity curve at 36°C. These temperature-dependence curves are reversible with no hysteresis being detected. No discontinuity or inflection has been observed in the heat capacity&apos; or the paramagnetic susceptibility.&apos; Likewise, no one has noted a change in crystal symmetry. In the present investigation Young&apos;s modulus, internal friction, coefficient of expansion, electrical resistivity, illustrated in Fig. 1, lattice constant, Fig. 2, thermal electromotive force, Fig. 3, and paramagnetic susceptibility, Fig. 4, were measured over an extended temperature range. The samples were prepared in two ways: (1) By cold pressing a sintered electrolytic powder compact,&apos; and (2) by electroforming from an aqueous solution. The electroformed samples were prepared by R. A. Ehrhardt and G. Bittrich by plating on copper or nickel tubes from an aqueous solution according to the method of Brenner, Burkhead, and Jennings.&apos; The pressed powder samples (method 1) were finally annealed at 1400°C in purified helium: the electroformed samples, packed in powdered chromium, were vacuum-annealed at 1000°C. From the composition of the original powder&apos; the purity of the pressed powder samples is estimated to be 99.8 pct Cr. Spectrochemical analysis furnished by E. K. Jaycox, revealed only slight traces of impurities in the electroformed sample (less than 0.001 pct), neither iron nor nickel being detected. Chromium deposited by this method is reported to contain approximately 0.05 pct 0.- Methods and Data Young&apos;s Modulus: For measurement of Young&apos;s modulus, an annealed, pressed powder sample, 0.114 x0.237x1.845 in., and an electroformed sample, 0.10 in. od, 0.01 in. id, and 1.86 in. long, were prepared. The resonant frequencies of the rod samples in forced longitudinal vibration were measured at a series of temperatures from —192" to 200°C by a method previously de~cribed.6,7 Because the samples were nonferromagnetic, iron- silicon or molybdenum permalloy tips (0.013 in. thick) were soldered to the ends. The softening temperature of the solder limited the temperature of measurement. Young&apos;s modulus, E,, of chromium at temperature, T, may be calculated from the resonant frequency of the composite rod, f,; the thickness of the tips, t; the length of the chromium sample at 25°C, l,.; the density of chromium at 25°C, pc (7.20 g per cc);5 and the thermal expansivity, Al/l25. Modulus differences for two temperatures, ET and E, are accurate to +0.002x10" dynes per cm2. ET = 4PAlc+2tyf Young&apos;s modulus at 25°C, Fig. la, is 28.2~10" dynes per cm&apos; (40.8xlO" si) in wrought chromium (upper curve). The modulus of the electroformed sample is apparently lower due to cracks. From the modulus measurements two transitions were observed: one with a critical temperature at 37°C, the other at —152°C. Internal Friction: The internal friction, 1/Q, was determined from the width, Af, of the strain amplitude-frequency curve at 0.707 times the strain amplitude at resonance;&apos; the internal friction, 1/Q, then equals Af/f. Fig. lb shows a sharp peak in internal friction at 38°C. The internal friction of the electroformed sample had a similar maximum. Thermal Expansion: The expansivity measurements, shown in Fig. 2, covering the temperature range —195" to +400°C were made by D. MacNair in an interferometric dilatometer8 sing a sample consisting of three pyramids 0.25 in. high prepared from wrought electrolytic chromium. Below —120°C the experimental points deviated up to ±2x10 from the drawn expansivity curve in Fig. 2 because of decreased precision of the quartz wedge thermometer at low temperatures. Near 38°C the thermal expansivity curve, Fig. 2, goes through an inflection corresponding to a minimum in the coefficient of expansion, Fig. ld, and a relative volume decrease on heating. Electrical Resistivity: The variation of electrical resistivity with temperature measured by the po-tentiometric method is also shown in Fig. l. The resistivity of the wrought chromium (upper curve) at 20°C is 13.6 microhm-cm; of electroformed chromium (lower curve) 12.8 microhm-cm. The lower value reflects higher purity and agrees closely with a published value." A minimum at 40°C occurs in the resistivity curves of both samples. No conclusive evidence for a transition near — 150°C was observed, but the points, Fig. 1, appear to deviate from a smooth curve between —120" and —160°C.

Jan 1, 1952