Search Documents

By R. J. Pruett

The Georgia kaolin district is the world’s largest producer of kaolin. Georgia production tripled from 2.87 Mt (3.17 million st) in 1968 to8.35 Mt (9.2 million st) in 1998. Development of the Georgia kaolin industry can be traced to the identification of the mineral resource, the adoption of innovative process technologies and the creation of markets for kaolin. Georgia kaolin is an abundant and high-quality resource that shows a range of advantageous properties. Technical developments in wet processing, delamination and calcination allowed production of high-value products. The use of kaolin pigments in the paper industry provided a market that absorbed the rapid growth in kaolin production.

Jan 1, 2000

EXECUTIVE COMMITTEES OF LOCAL SECTIONS New York L. W. FRANCIS, Chairman, WILLARD S. MORSE, Vice-Chairman. THOMAS T. READ, Secretary, Woolworth Bldg., New York. N. Y. P. A. MOSMAN, Treasurer. LOUIS D. HUNTOON. Boston HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. AUGUSTUS H. EUSTIS, Secretary-Treasurer, 131 State St., Boston, Mass. TIMOTHY W. SPRAGUE, HENRY A. WENTWORTH. Columbia F. A. THOMSON, Chairman. GEORGE W. RODDEWIG, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. 0. Drawer 2154, Spokane, Wash. R. S. McCAFFERY, S. H. RICHARDSON.

Jan 9, 1914

By C. R. Summers, J. N. Murphy

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneurnaric drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115 -dbA s rope drill to approximately 100 dbA.

Jan 1, 1974

By A Rorke, B Cubitt, R Beeslaar

The recent drop in the value of the South African Rand has resulted in an increased export value for South African coal and has lead to new coal reserves becoming available for mining. Very often these reserves are in close proximity to existing structures and utilities thus calling for stringent blast control measures to keep the risk of vibration, air blast and fly rock damage to a minimum.

Jan 1, 1997

By D N. B Skinner, R L. Brathwaite, M S. Rattenbury

The Institute of Geological and Nuclear Sciences Ltd has carried out a mineral resource assessment of the Coromandel region, one of the most mineral-rich regions of New Zealand. The assessment focussed on metallic minerals and clays, because these are the main commodities that have potential for increased production and export from the region (and from New Zealand).   Three steps were used in the assessment: 1) development of mineral deposit models, 2) comparison of the models with regional geology, structure, geochemistry and past mineral production to estimate the number of undiscovered mineral deposits, and 3) application of grade-tonnage models to determine the quantity and value of the known and undiscovered resources. In step 1, descriptive and grade-tonnage mineral deposit models were developed for 11 different types of mineral deposits: ò     Low-sulphidation andesite-hosted epithermal Au-Ag ò     Low-sulphidation rhyolite-hosted epithermal Au-Ag ò     High-sulphidation quartz-alunite epithermal Au ò     Porphyry Cu-Au-Mo ò     Andesite-hosted polymetallic veins adjacent to mineralised porphyry stocks ò     Zn-Pb-Ag skarn ò     Cu-Ag skarn ò     Hot spring Hg ò     Shoreline placer Ti ò     Rhyolite-hosted halloysite clay ò     Volcanic-related kaolinite clay   Step 2 was aided by a geographic information system (GIS) assembled from a number of digital spatial data sets including: a digital elevation model, an aeromagnetic map (from open file mining company data), a geological map (from the GNS QMAP project), location of areas of hydrothermal alteration, locations of mineral deposits (from the GERM database), stream sediment geochemical analyses (from the REGCHEM database), and a lineament map derived from satellite remote sensing data and the digital elevation model.   Based on May 2001 commodity prices, potential resources estimated for the 11 mineral deposit and grade-tonnage models total NZ$22 806 million for the metallic minerals, NZ$1000 million for halloysite clay deposits and NZ$57 million for kaolinite clay deposits.

Jan 1, 2001

By Gregory Poole

With access to the World Wide Web, many resources are readily available for improving claim reports. With a little time spent on line, a more thorough report can be created. Claimants will accept the conclusions of a report more readily when they can view support information on their own computer, particularly when the support information is not just from blasting related web sites. Some suggested resources are discussed including aerial pictures, local tax maps, topographical maps and home repair web sites. This paper provides suggestions for tracking down support information on the web and information on how to properly reference this information. Case studies of several claim investigations are presented. These are some examples of how a little time spent online provided clear and convincing evidence to support the conclusions of the investigation.

Jan 1, 2006

By E. G. King

The literature contains little thermodynamic information regarding inter-oxidic compounds of the ferroalloy elements and, as a result, thermodynamic considerations of extractive and utilization processes involving these elements have been hampered. As part of a Bureau of Mines program to improve this situation, this paper reports the heats of formation of three calcium vanadates and two magnesium vanadates. There were no previous similar data for any of these compounds. The experimental method was hydrochloric acid solution calorimetry, using calorimetric reaction schemes involving the vanadates and their component oxides. The results were expressed as heats of formation from the component oxides and from the elements. Corresponding free energy of formation values were calculated. The data show that the calcium and magnesium vanadates are stable with respect to all possible decompositions in which vanadium remains pentavalent. This conclusion is similar to the one drawn by Koehler6 for three sodium vanadates.

Jan 1, 1962

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSWA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. metallic mining workforce from March through September 1986. Similar reports have been published for the stone, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By Janis A. Shandro

The mining sector is a major economic driver for Canadian, and British Columbian communities. In parallel strong commitments have been made by industry to the well-being and sustainability of associated communities. However, these dimensions are the least understood. Especially lacking are focused regional investigations that compare the well-being and sustainability of communities dependent on different resources sectors. It is hypothesized that this type of comparative analysis will help to foster a greater understanding of what makes a resource or mining community healthy and sustainable. This paper describes research that examined community-level indicators associated with well-being (e.g. education, income and employment) and sustainability (e.g. economic diversity). The indicators were derived from Canadian Census data for 31 British Columbia resource-based communities (with a focus on mining) during a period of time (1991 to 2001) when resource sectors experienced an economic downturn. Our findings identify that during this decade, mining communities differed significantly from other resource-based communities, and comparative analysis of census derived indictors illuminate challenges that mining communities in British Columbia face with respect to wellbeing and sustainability (such as economic diversity, unemployment, and population loss). To contribute to the mining sector?s efforts towards meeting their commitments to communities, this paper concludes by proposing strategic opportunities aimed at the enhancement of mining community sustainability for policy-makers, communities, and the mining industry to consider.

May 1, 2011

By George A. Savanick

The objective of this research is to develop a method for measuring the tensile strength at the interface between minerals in rock. These measurements reflect the strength of the attractive forces operating at crystalline interfaces in rock. Since these forces act in opposition to the forces set up in various rock fragmentation processes, measuring their strength may help in designing more efficient methods of rock fragmentation. The method developed for measuring the strength of intergranular adhesion in rock involves separating a bicrystal from the rock and determining the tensile strength at its solid-solid interface. This technique has been successfully applied to the study of quartz-feldspar interfaces separated from massive pegmatites, graphic granite, and the Rockville granite, yielding average tensile strengths of 5.86, 8.62, and 10.65 meganewtons per meter squared (MN/m2) (850, 1,250, and 1,524 psi, respectively). The data this technique provides indicate that the members of these bicrystals are strongly adherent. Examirtation of bicrystals broken at the crystalline interfaces indicates that the bonds responsible for this adhesion operate over only a portion of the interfacial area. This work conclusively demonstrates that tensile strength tests can be conducted on small selected areas; for example, grain boundaries in rock. The small-scale zones of strength or weakness determined in this way can be related to the overall strength of the rock.

Jan 1, 1972

By James M. Baugher, Donald W. Conrad, William J. Wiehagen

This report describes a process for quickly developing information that is useful for skills training. The process is called job training analysis (JTA). Its main use is to structure skills training at the jobsite. JTA supports structured skills training by identifying the job duties, tasks, and steps and the reasons why those job components are important. The outcome of the JTA process is a worksheet—a training outline based on the knowledge and expertise of experienced workers. Time invested in developing a JTA will result in significantly more time saved when it is used appropriately by skilled trainers. Like a roadmap, JTA saves time and energy. Experimental work at several mine sites helped document, refine, and validate the JTA process. JTAs for two mining jobs—roof bolting and lift truck operation—at two different mine sites are used to illustrate some of the concepts and the specific JTA process described in this report. The work at these two sites was influenced by cooperative work between the Mine Safety and Health Administration (MSHA) and the National Institute for Occupational Safety and Health (NIOSH) at several other mine sites and prior collaborative work with the U.S. Navy. The mining JTA process is grounded within the military research on the design of instructional systems. MSHA and NIOSH worked to simplify and apply the military training development model for mining industry use through collaborative work at several mine sites. The JTA process involves three activities: (1) planning, (2) a 1- to 3-day workshop where the JTA is developed using facilitated work with subject-matter experts, and (3) followup. Guidelines and considerations for each of these activities are included. Results indicate that the JTA process has been well received and valued by mining industry participants. It blends aspects of health and safety, production, maintenance, and crew coordination.

Jan 8, 2006

Ore samples generally require preparation before analysis. Serious problems can occur with contamination degradation and particle size effects. Both grinding element contammation and sample cross contamination havebeen bound to be related to sample hardness and operator technique. For best results with minerals relevant to the steel industry, the use of Siebtechnik-type mills required a combination of careful planning, short grinding periods and intermediate sieving of the sample. The results may be extended to most mineral, rock, and refractory sample preparabons.

Jan 1, 1978

About 15 per cent of total electricity (400 MkW) was generated by nuclear power plants in the world (2009) and about 36 000 tons of uranium has been mined in uranium mines annually. Radioactive waste material is produced from uranium mines and nuclear power plants. The wastes must be disposed or stored safely for long-term. If they leak and/or move from disposal or storage sites due to air/groundwater flow, then a serious environmental pollution can occur. Hence, multi-layer system has been proposed and employed in order to seal off these radioactive waste materials from biosphere. Basically, bentonite is now used for establishing absorbing and sealing layers in this system. However, the amount of high quality betonite is very limited and in some cases it is hard to be obtained.On the other hand, a great deal of refuse from coal burning plants is produced every year and the amount of it is expected to be higher each year, especially in developing countries. More than half of flyash is utilised and the remaining is disposed at the disposal sites. However, the life of the disposal site is limited and it is diff cult to find a new disposal site. It is requested that the percentage of the utilisation of the flyash be increased in every field.From the above two points of view, a flyash-based barrier layer/cover system is considered in this research and this paper discusses the applicability of flyash as a content of barrier layer/cover material based on the results of a series of laboratory tests.

Dec 6, 2010

THE first session of the Institute was held in the hall of the Washington University, Wednesday evening, May 27th, President Raymond in the chair. After the address of welcome by Hon. Thomas Allen, and the reply of Mr. Raymond, the following names were presented for election as members and associates, duly indorsed by the Council. They were unanimously elected : *Henry Booth, - New York City. *Charles H. Morgan, - Worcester, Mass. *Howard Painter, - West Chester, Pa. *Dr. M. J. Goodfellow, - Eberhardt, White Pine Co., Nevada *Otto Wittelshach, - Eureka, Nevada. *John T. Williams, - New York City. †Charles A. Young, - Philadelphia. *Charles E. Stafford, - Boston, Mass. *Arnold Hague, - Orange, N. J. *Richard Pearcé, - Black Hawk, Colorado. *W. R. Maffet, - Wilkes-Barre, Pa. *Prof. George A. Koenig, - University of Pa., Philadelphia *Prof. R. Nutting, Jr., - Indianapolis, Indiana. *Edwin Mickley, - Hockendauqua, Pa. *G. C. Broadhead, - St. Louis, Mo. *Dr. Adolph Schmidt, - St. Louis, Mo. *Alexander Leonhard, - St. Louis, Mo. *Edward D. Meier, - St. Louis, Mo. *John W. Meier, - St. Louis, Mo. *Prof. Forrest Shepherd, - St. Louis, Mo. *Edward Walsh, - Pilot Knob, Mo. *George Riggs, - St. Louis, Mo. †Col. Chas. B. Parsons, - Cadet, Mo. † W. A. Scott, - Mine La Motte, Mo. *Prof. Paul Schweitzer, - Columbia, Mo. *William E. Guy, - St. Louis, Mo. †William Harris, - St. Louis, Mo. *Henry Black, - Pittsburgh, Pa. †W. Noyes, - New York City. *W. Lorenz, - Philadelphia. †E. A. Whetmore, - New York City. * Members. †Associates.

Jan 1, 1875

By A. Sinha, N. K. Babar, H. R. Kalihari, A. K. Chakraborty, M. R. Saharan, C. P. N. Pathak

A case study is presented on the optimization of cable bolting patterns in cut-and-fill stopes at the Chikla Mine, MOIL, India. Rock mass characterization, using Bieniawski’s RMR and Barton’s Q, indicated that the stopes lie in the “no supports required” to “spot bolting required” support categories. In contrast, the current practice of cable bolting in a 2.0 m by 2.0 m grid pattern for stope widths less than 12 m displays different results. Numerical modelling results are in line with the rock mass characterization study. It can be affirmed, as well, that no cable is carrying rock loads greater than 5 t. This fact is derived from observational behaviour of the crown pillar of an experimental stope with open stoping operations and hanging cables in the cut-and-fill stopes of the mine. An increase in the cable bolting grid spacing is, hence, recommended for implementation by mine management, based on the study described in subsequent sections. It is also suggested that the mine adopt the open stoping method, provided results of a rock mechanics instrumentation program in an experimental stope with a cable bolting grid of 2.5 m square are favourable.

Jan 1, 2007

By Tom Palangio, Ralph M. Olmstead

Video inspection of boreholes with cameras developed specifically for the mining industry is now possible. These designs are reliable, cost effective, and have the flexibility to be used in other applications.

Jan 1, 1998

By Martin Pratt

This paper is an overview of deep foundation engineering in Hong Kong past, present and future. The enormity of the subject compared with the space available makes brevity inevitable. Issues of construction and design are covered and some examples of recent challenging projects are given. The content is aimed at those with an interest in foundations generally, but with limited knowledge of the Hong Kong scene. Reference is made to informative publications for further reading on specific topics.

Jan 1, 2000

By Jürg Schlumpf

Concrete is one of the decisive construction materials, also for the AlpTransit Gotthard Tunnel. The client has many requirements, and many are the solution possibilities that concrete systems can offer. Cement producers and concrete admixture manufacturers have been challenged to design and test jointly concrete systems for cast and sprayed concrete. The testing operation followed the scenario laid out by the Gotthard AlpTransit Project management?s instructions ?Testing system for concrete mixes.? Various supplier teams have applied for the concrete systems for sections Amsteg/Erstfeld, section Sedrun and/or sections Bodio/Faido and have also followed through with the tests. As was to be expected, the rate of failed mixes matched the level of the requirements. Thanks to this system, it was nevertheless possible to test complete concrete systems for all sections and to get them approved. The joint ventures tendering for the contracts were allowed to include only approved mix designs in their bids. Workability and durability are of paramount importance for cast and sprayed concrete mixes. Durability is influenced by the chosen mix design where binder concept and well-defined water content, i.e., impermeability, are determinant. Aggregates for AlpTransit are to be considered as given. The concrete mix design also determines workability. Because ambient conditions and also requirements with respect to workability are subjected to change, it is necessary that the mix designs include control measures. The choice and number of components for the concrete systems (cement, additives and admixtures) allow adaptation to changing conditions. For AlpTransit such adaptive measures must meet very strict requirements.

Jan 1, 2008

By O. R. Eckstrand, M. Asif, P. L. Schwann, A. J. Naldrett, R. J. F. Scoates

Paper presented at the IAGOD international symposium on mineralisation related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. PGE-bearing sulphide mineralisation is contained in the lower 600 m of the Upper Central Layered Zone of the intrusion. There are four regimes with distinctive crystallisation characteristics. PGE content is low, both in bulk rock and in terms of metal in 100% sulphides, in the sulphide-rich cumulates but increases sharply in the sulphide-poor cumulates at the base of regime 1. Increases in regime 2 have no such clear relationship with incoming cumulus sulphides. PGE contents are low throughout regime 3, but regime 4 has sulphides with high PGE content, decreasing rapidly upwards, at the base of many of its cyclic units. The observations are interpreted as indicating that sulphide saturation occurred in the middle of a cyclic unit in regime 1, after which fractional segregation of sulphide caused a systematic decrease in PGE content. The resulting contrast between 40 000 ppb PGE in sulphides below the mineralised zone and less than 1 000 ppb above is of practical importance in exploration for such zones. In regime 2 the magma chamber was open to fresh influxes and PGE content was not so sensitive to sulphide saturation. In many regime 4 units influxes of new magma caused immediate sulphide saturation and PGE depletion, so that PGE-rich cumulates do not underlie PGE-bearing sulphide zones. Theoretical analysis indicates that regime 1-type behaviour is likely to characterise intrusions below the level at which plagioclase has entered as a cumulus phase and regime 4-type behaviour above

Apr 1, 1994

By D. M. Milne, P. J. Lunder, R. C. Pakalnis

During the mining of an open stope, deformation of the hanging-wall and the potential for dilution generally increase with the size of the exposed hanging-wall. Excluding discrete structures that may delineate unstable blocks, the mechanisms that drive hanging-wall deformation and possible dilution comprise several factors which can include elastic, plastic and discontinuum deformation. These stages of deformation are not mutually exclusive and at any point during mining all three of these mechanisms may be acting on the hanging-wall rock mass. Computer modelling techniques are available to analyse the three stages of deformation, but the difficulty lies in trying to obtain realistic rock mass properties for input and in determining when each stage of deformation is acting. Instrumentation data can be used to predict the effect of continued mining. However, it is often difficult to calibrate numerical models against field data owing to the large number of input parameters required. An empirical approach is recommended that uses two new parameters, the radius factor and the effective radius factor. A method is proposed for predicting the effect of continued mining from existing deformation and dilution data for a given hanging-wall

Apr 1, 1996