Search Documents

By K. J. Griffin, G. W. Rosval

"In our increasingly competitive market, attempts to improve productivity by increasing axle loads have placed more severe demands on rails. CP Rail thus requires stronger, tougher, and more wear-resistant rails from steel manufacturers. The choice of any rail steel is always a compromise between technical and economic factors. The technical assessment of a candidate rail consists of laboratory and field testing. Laboratory evaluation of rail steels cannot adequately model many service conditions and must, therefore, be supplemented by long-term field testing. The field testing conducted on CP Rail is the subject of this paper.Long-term, in-track, assessment of candidate rail steels begins with the selection and re-laying of a test curve representative of the intended service with both the candidate rail and a control rail steel (i.e. the present intermediate or premium rail standard). The wear performance of the candidate rail is evaluated, in relation to that of the control rail, using data obtained with a rail profilometer developed by the Research and Development Department of CP Rail. Qualitative observations are also periodically made to evaluate the relative susceptibilities of the two rail types to surface defect formation. Testing continues until stable metal loss patterns are achieved. Relative life predictions are then made and detailed monitoring of the test site is discontinued.CP Rail's in-track assessment program for premium rails has resulted in the establishment of a new CP Rail premium rail standard - low-alloy, head-hardened, rails have replaced high alloy rails. The wear/fatigue lives of these new premium rails exceed those of our previous standard by more than 50%, and they also exhibit excellent weldability. CP Rail will continue to evaluate new premium and intermediate strength rail products."

Jan 1, 1988

By Sanford J. Douglas

This publication describes a study by the Federal Bureau of Mines of devices and methods used for testing and splicing 4,160-volt and 440-volt cables and for providing ground-fault protection for 440-volt circuits, as developed and used by the electrical staff of the Tecumseh coal mine, an open-pit operation at Boonville, Ind. The testing and ground-fault devices described should find ready application in other open-pit mines, and, with suitable modifications for voltages involved, in underground mining. The devices and testing methods are based on sound engineering principles and are time-tested and economically feasible, Four devices are used: A high-voltage tester, and a low-voltage high- current tester, both for testing 4,160-volt cables; a tester for 440-volt cables; and, electronic ground-fault protective device for 440-volt cable circuits. All the cable testers and the grounding device were designed and built at the mine from standard parts. They are inexpensive, dependable, and job tested, An attempt has been made here to describe them in enough detail so that interested persons can assemble duplicate units.

Jan 1, 1960

By I. L. Nichols

The Bureau of Mines is investigating vanadium recovery from various domestic resources. A low-grade carnotite ore sample containing 0.34 pct V20S and 0.04 pct U30S was leached, and the results were compared with those of similar leach tests using a mill-grade sample containing 1.26 pct V205 and 0.19 pct U308. Experiments on the two ore samples included agitation leaching, pugging, salt-roast leaching, and autoclave leaching. None of the leaching methods investigated showed any significant advantage over another except autoclaving, which reduced the leach time but at the expense of greater acid consumption. Typical of the experimental results attained are the data gathered from the agitation leaching tests. Agitation leaching of the mill-grade ore with 100 lb/ton H2S04 resulted in extractions of 94 pct U308 and 33 pct V205. To increase the vanadium extraction from 33 to 91 pct required concentrations of 300 lb/ton H2S04 and 10 lb/ton NaC103. Complementary agitation leach tests on the low-grade ore required 200 lb/ton H2S04 to extract 94 pct U308, and 300 lb/ton H2S04 and 10 lb/ton NaC103 to extract 90 pct V205.

Jan 1, 1983

By S. Kouniali

Experience with knowledge-based systems for Layout planning and roadway support dimensioning is on hand in European coal mining since 1985. The systems SOUT (support choice and dimensioning, 1989), SOUT 2, PLANANK (planning of bolt-support), EXOS (layout planning diagnosis. 1994), Sout 3 (1995) have been developed in close cooperation by CdF1. INERIS2. EMN3 (France) and RAG 4, DMT5, TH - Aachen6 (Germany); ISLSP (Integrated Software for Layout and support planning) development is in progress (completion scheduled for July 1996). This new software technology in combination with conventional programming systems. numerical models and existing databases turned out to be suited for setting-up an intelligent decision aid for layout and roadway support planning. The system enhances reliability of planning and optimises the safety-to-cost ratio for ? deformation forecast for roadways in seam and surrounding rocks, consideration of the general position of the roadway in the rock mass (zones of increased pressure, position of operating and mined panels). ? support dimensioning ? yielding arches, rigid arches, porch sets, rigid rings, yielding rings and bolting / shotcreting for drifts ? yielding arches, rigid arches and porch sets for roadways in seam ? bolt support for gateroads (assessment of exclusion criteria and calculation of the bolting pattern) ? bolting of face-end zones (feasibility and safety assessment, stability guarantee).

Jan 1, 1996

By G. H. Lind

Seven full and partial pillar extraction operations were visited in New South Wales, Australia, in the early parts of 2001. Certain factors unique to these operations have led to the general success of the safe and economic extraction of these coal pillars. Some of these factors attributable to the overall success of these operations are discussed in this paper. In particular, geotechnical mapping, specific legislation pertaining to pillar extraction, mining methods, the role of temporary supports and training are described. It is found that some of these factors have useful attributes which could be used to design a methodology for extraction of underground coal pillars in the Witbank and Highveld coalfields of South Africa.

Jan 1, 2002

By Mike Boissonneault

It was three years ago when the “storm of the century” had taken a firm grip over the Pacific West Coast and inland areas. At the Big Sky ski resort in Montana on Christmas morning two ski patrollers set out to perform an explosives “hand charge” avalanche control mission that would see only one return. It has been difficult to determine exactly what happened. Investigators do know that there were three separate and consecutive attempts to light a safety fuse, when it had apparently been burning since the first attempt. Time ran out after the third attempt. Although this accident has had a profound impact on North American avalanche control programs, I am sure it pales in contrast to the shock and grief experienced by family members who lost a loved one.

Jan 1, 2001

By John Heter

An alum/sulfur deposit (USDA organic registered) was mined underground for alunite (K,Na) Al3 (SO4)2 (OH)6 from the early 1900s to the 1930s. It is now being mined as an open pit quarry. A larger assemblage of minerals is included with this method (Alunite, Potassium?Alum, Jarosite, Gypsum, Native Sulfur and K-feldspar). This assemblage of minerals provides the necessary requirements as a Volcanic Soil Conditioner Sulfur-Potash. Heart of Nature? Company has been marketing this product to farmers on the west coast as a (1) pH reducer, (2) soluble sulfur and potassium source for plant growth and (3) soluble calcium. Recently, a new market has been tapped. This product has been found to solve many odor, bacteria and algae problems faced in the dairy industry.

Jan 1, 2008

By D P. Sainsbury, B L. Sainsbury, A Vakili, H-D Paetzold, P Lourens

The cave propagation behaviour of a jointed rock mass is strongly governed by the unique nature of joints and discontinuities, together with the intact strength of rock bridges that make up the rock fabric. A discrete finite difference (DFD) modelling technique has been developed to allow for the detailed consideration of the rock mass structural fabric at many scales and through many different stress paths that can be used for complex mine-scale analysis. The DFD methodology uses interfaces to explicitly represent large-scale structures and ubiquitous joints embedded within the simulated rock mass matrix to characterise intermediate structures. Through simulated testing of DFD materials, properties such as strength anisotropy and scale effects can be obtained. This paper discusses the successful application of implementing a DFD modelling technique for the back-analysis of caving-induced subsidence behaviour of Lift 1 at the Palabora mine.CITATION:Sainsbury, D P, Sainsbury, B L, Paetzold, H-D, Lourens, P and Vakili, A, 2016. Caving-induced subsidence behaviour of Lift 1 at the Palabora block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 415–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By António Fiúza, Anthony Danko, Patrícia Leitão, Aurora Futuro, Cristina Vila, Lurdes Dinis

The average global recovery rates for processing scheelite ores by physical methods are normally in the range 50 to 70%, and it is problematic to attain a minimum grade of 60% WO3 in the concentrates without penalizing further this yield. Direct hydrometallurgical processing of low-grade concentrates or medium- to high-grade ores may become an interesting global economic alternative as it allows increasing the recovery rate, avoiding major penalizations due to the grade of the concentrate and increasing the added value of the final product. Leaching of scheelite by sodium carbonate presents several advantages such as its selectivity regarding the dissolution of troubling metals like iron and aluminium, allowing for a simple and flexible process diagram. However, it has the disadvantage that it is performed at high temperature and pressure with a high consumption of reagents. The feasibility of leaching is appraised by the extraction yield and selectivity, but also by the operating cost. Considering these aspects, a relevant objective of the research was to transform alkaline pressure leaching into a feasible processing alternative directly applicable to both medium- and high-grade ores and simultaneously to low- and high-grade concentrates produced by physical methods. The research used ore samples and low-grade concentrates from a typical skarn orebody as well as high-grade concentrates from a chalcopyrite-scheelite orebody. Different operating conditions were tested. Temperature, pressure and reagent concentration showed to be fundamental, but not exclusive, in determining the leaching behaviour. The operating conditions are milder than the ones generally proposed in the literature or currently in use in industry, but with higher carbonate consumptions. The research was oriented towards potential industrial implementation allowing for the application of optimization methods and straight scale-up to pilot-plan design and project.

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By A. Frits van Tol, Rodriaan Spruit, Jan H. van Dalen

"Abstract In recent years, there have been major problems with deep excavations in urban areas supported by diaphragm walls. In some cases, like the fatal Nicoll Highway collapse in Singapore the quality of the D-walls was not the cause. However in other projects, like the problems with the major leak in the walls of the Boston Big Dig and with leakage in a few projects in Belgium and The Netherlands was related to poor D-wall quality. Leakage through the D-walls at the joints in deep excavations led in these cases to very serious settlement behind the walls, in the case of the North- South line in Amsterdam, there was severe damage to historical buildings. This paper describes ongoing research that focusses i on acquiring more knowledge on and improvement of D-wall installation, in particular the flow process prior and during casting ii on the detection of anomalies prior to excavation and iii on the composition of the concrete mixture in view of a better and more sustainable concrete quality of D-walls.INTRODUCTIONIn the case of deep excavations in urban areas close to neighbouring buildings, diaphragm walls are one of the best feasible solutions for the retaining structure. Although the costs of D-walls generally exceed the costs of alternative wall solutions, the advantages are decisive in many situations. The main advantages of D-walls are the limited impact of the installation on the built environment, the high stiffness and bearing capacity and the retention of water, even at considerable depths. This makes Dwalls often the preferred solution for deep excavations Sometimes the D-walls are the temporary support while for the final stage a complete concrete box is constructed in the excavation. In many other cases the D-wall has the permanent function of retaining soil as well as groundwater.In the last ten years, there have been major problems with deep excavations in urban areas supported by diaphragm walls. In some cases, like the fatal Nicoll Highway collapse, 2004 , the quality of the Dwalls was not the cause. In other important failures like the collapse of the Archives in Cologne, 2008 and Dubai Infinity Tower Flooding, 2007 a combination of design and quality issues played a role. However, the major leak in the walls of the Boston Big Dig was related to poor D-wall quality (McNichol, 2000). Van Tol et al, (2010) describe a number of case studies in Belgium and the Netherlands, with leakage through the D-walls at stop end joints. In several cases with deep excavations these leakage caused serious surface settlements behind the walls. In the case of the North-South line in Amsterdam, there was severe damage to historical buildings. All these cases have generated considerable additional costs and delays, and subsequently public and political concern. Van Tol et al. (2010) present several possibilities to improve the quality of D-walls.Other disputes related to D-walls deal with the quality of the concrete and the sustainability of D-walls applied as a permanent wall. In particular the porosity of the concrete cover is sometimes problematic."

Jan 1, 2014

By B. Salt, R. Sullivan, E. Roos, M. de Vries, K. McKenna, L. R. Nelson, M. J. N. Uys, P. Jacobs, E. Munnik, P. Lewarne

A review is presented of the furnace cooling system design and operating developments since the initial furnace start up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators in particular to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement to operate this slag in a relatively highly superheated state (?T ? 400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomisation. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to Hatch high-intensity, water-cooled, copper Waffle coolers and tapblocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area) coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the Hatch Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

AUSTRALIA CHAPMAN Gary JOHN WAGSTAFF CONTSRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE BRISBANE HILLAR Jaaes Director J.A. HILLAR & ASSOCIATES 99 Woolwich Road WOOLWICH, NSW 2110 WAGSTAFF John Managing Director JOHN WAGSTAFF CONSTRUCTIONS PTY. LTD. 1 Ashgrove Crescent 4060 ASHGROVE, BRISBANE AUSTRIA FUCHSBERGER M. TECHNISCHE UNIVERSITAT INSTITUT FUR BODENMECHANIK Rechbauerstrasse 12 8010 GRAZ

Jan 1, 1994

The wage structure of graduate White men in 1979, by Adri Kruger, Pretoria, Human Sciences Research Council, 1979.76 pp. R5,00. (Reviewer: D. G. Malan) Financial Times mining international yearbook, edited by WilIiam G. Nightingale. London, Longman, 1980. 750 pp. £24 by surface, £34 by air. (Reviewer: J. D. Austin) Techniques in mineral exploration, by J. H. Reedman. Barking (U.K.), Applied Science Publishers, 1979. 533 pp. $90. (Reviewer: D. L. Kyle) Practical geostatistics, by Isobel Clark. Barking (U.K.), Applied Science Publishers, 1979. 129 pp. £13,75. (Reviewer: D. G. Krige) Uranium: The balance of supply and demand 1978- 1990, by the Uranium Institute. London, Mining Journal Books, 1979. 61 pp. £8,50 by surface,,£9,25 by airmail. (Reviewer: D. J. Crowe) Wear and abrasion in industry The South African Institute of Mining and Metallurgy and the Institution of Metallurgists (South African Branch) is to hold a colloquium on the topic of wear and abrasion of metals in February 1981. Steel rolling The International Conference on Steel Rolling sponsored by The Iron and Steel Institute of Japan will be held in Tokyo, Japan, from 29th September to 4th October, 1980.

Jan 1, 1980

By D. D. Ndenguma

This investigation compares the results from an experimental and numerical study of air flow in a scaled-down underground coal mine model. This was done in order to determine if numerical analysis can be relied upon when searching for ventilation solutions to control high concentration of coal dust and methane gas in underground coal mines. Steady state analyses were used to identify flow patterns and recirculation regions within the mining section while transient state analyses were used to determine the time taken to extract the initial air from the model. The agreement between the experimental and numerical results indicates that numerical modelling is useful in this regard. The study went further to devise a method of determining the optimum position of the jet fan that is responsible for mine-gas dilution at different stages of mining.

Jan 1, 2014

By Henry Rawdon

THE following note describing the behavior of copper under rather unusual conditions is offered here for its suggestiveness rather than as a complete study of the question. The examinations described were made because of a request for information concerning the embrittlement of copper when heated in a molten salt bath (sodium chloride) for the purpose of cleaning it, as well as for softening it. It is well known that metals may be rendered very brittle by electrolytic action, in aqueous solutions, in all probability by the action of nascent hydrogen, and it was suspected that perhaps the embrittlement of the copper by means of the molten salt was produced in a somewhat similar manner. It was found that the copper was in contact with iron (or steel) while immersed in the molten salt, through the occasional use of an iron stirring rod, iron forceps for handling the pieces, and an iron pot for containing the fused salt. In the electrochemical potential series iron and copper stand some distance apart, copper being electronegative to the iron. Assuming that the two metals bear a similar relation to each other, when immersed in a bath of molten salt, as they do in an aqueous solution, they would be expected to form a galvanic couple, the copper being the cathode. By this means the copper might be embrittled, as often happens in aqueous solutions, by the action of the liberated hydrogen. In this case, however, the embrittlement must be attributed to some other agent than hydrogen. To demonstrate how copper may be embrittled under these conditions, two small rods, one of copper and the other of mild steel, approximately 3/8 in. (9.5 mm.) in diameter, were immersed in a bath of sodium chloride that had been heated somewhat above its fusion point (melting point of sodium chloride is 819° C.) and an electromotive force of approximately 6 volts from a storage battery was impressed upon the system. The copper was made the cathode and the action was continued for

Jan 2, 1920

By William R. Yernberg

The “China & East Asia Mineral and Energy Re-sources Symposium — CEAR 2000” was held Jan. 23-26, 2000 in Denver, CO. Conference sponsors included Resources and Technology Symposia of Colorado and the Asian Journal of Mining. The meeting was attended by representatives from China, Japan, Mongolia, Korea, eastern Russia (Siberia) and the United States. The US attendees consisted of interested parties from mining and energy companies, financial institutions, consultants and government agencies. In his opening statements, L. Maness, Jr., president of Resources and Technology Symposia of Colorado, said that the “goal of the conference was to make jobs and friendships and to introduce people to each other.” The conference provided an opportunity for Western mining interests, including mining companies and investors, to meet with government agencies from both sides of the Pacific.

Jan 1, 2000

Heavy mineral deposits are becoming more complex in terms of their compositional variation, particle mineralogy and size distributions, and present challenges for the operation of separation equipment to achieve the required grades and recoveries. Changes in equipment design and concepts potentially provide new opportunities for the beneficiation of heavy mineral sands deposits. The development of a framework for the fundamental understanding of separator performance issues is a first step to develop new machines. This paper will present a first step analysis of electro-static and magnetic separation machines with their application to real separation scenarios.

Jan 1, 2010

By Y. H. Wang

During the last two decades many research projects were conducted to study the load requirements for the powered supported longwall faces (1-6). Significant results had been achieved by these researches. Most of the previous studies were rarely designed to understand the mechanisms of interaction between the supports and the surrounding rock, or to correlate the stress conditions around longwall faces to the mining operations both in time and space. In case of the shield supported faces, the roof-to-floor convergence is very difficult to measure due to the high percentage of roof coverage. The external load on the supports can not be determined from the leg pressure data alone due to the existence of the lemniscate links. Therefore, there is a real need in that a simple engineering method be developed to monitor the variations of roof load on the shield supports, the roof-to-floor convergence and the roof stress restoration in the gob area as the mining proceeds. Only with the results of these measurements, a further understanding about the mechanisms of interaction between the supports and the surrounding rock can be achieved and a criterion of designing or selecting the optimum mechanical parameters of the shield supports can finally be developed.

Jan 1, 1986

The Upper Waimangaroa mining permit is part of the Buller Coalfield and lies on the eastern side of the Stockton-Denniston Plateau. The mining permit area is estimated to contain a total in-ground coal resource of 58 million tonnes, contained within 13 separate coal resource .blocks. The coal is Bituminous High Volatile B rank with export potential as semi soft coking or thermal coal. The Northern Opencast mine is the first mine proposed for Upper Waimangaroa and consists of the three resource blocks at the northern end of the permit area. The highwall of the mine will cut into the Mt William Range resulting in overburden cover of up to 150 metres in some areas. The ability to rehabilitate the area after mining was a major consideration in the design of the mine. The Northern Opencast area has been geologically mapped, extensively drilled and effectively modelled using Vulcan software. Three distinct coal seams are present and the mineable in situ resource is estimated at 8.7 million tonnes of which approximately 7.1 million tonnes is likely to be recoverable. It is proposed that this resource will be mined using opencast methods and the void will be backfilled with overburden. The life of the mine is at this stage estimated at 19 years based on an annual production of 500,000 tonnes at 1.8% sulphur and the Upper Waimangaroacoal will be blended with low sulphur coal from the Greymouth Coalfield to meet export specifications. The Northern Opencast area contains a range of native flora and fauna and physical features which make it an environmentally significant area. Mining will totally modify the area, thus an effective rehabilitation scheme is an integral part of the mine plan. Various rehabilitation methods will be used, and wherever possible, the backfilled areas will be rehabilitated so as to resemble the original area as closely as possible.

Jan 1, 1998