Search Documents

By W. P. Yant, G. W. Jones

"Introduction.During the past two years the Bureau of Mines has conducted a study of natural-gas heaters*** to determine (1) what types of heaters literate carbon monoxide; (2) why carton monocide is liberated; and (3) how, by change of design or construction, the liberation of this gas can be largely eliminated, In addition to the above study the bureau has investigated cases in the Pittsburgh dis¬trict where fatalities have resulted from carbon monoxide given off by natural-gas heaters.Since these fatalities were first brought to the attention of this bureau through the press, it is likely that some cases were missed and thus not listed. On the other hand, some cases reported as being due to carbon monoxide poisoning, on investigation were found to be due to causes other than carbon monoride.The cases listed herein were shown in all probability to be due to carbon monoxide. Those in which there is any doubt have been omitted; so have those in which there was part asphyxiation, where the victims later recovered."

Feb 1, 1924

By Srinivasulu Tadisetty

The productivity and safety of Indian longwall operations are insignificant because of complex geomechanical conditions. Therefore, the continuous monitoring and forecasting of abnormalities is imperative. Authors developed an innovative real time system and implemented in one of the Indian longwall mines. The real time system was successfully acquired data from underground chock shields and classified the behaviour in real time as per the standard norms. Furthermore, it forecasted the abnormal behaviour of chock shields promptly. The management was implemented appropriate precautionary measures based on real time forecast. Subsequently, the longwall operations were successfully completed with enhanced productivity and safety. This paper discuss the impact of the innovative system on productivity of experimental longwall mine.

Jan 1, 2006

By J. Bakken, M. Th. Jonsson, G. Sævarsdottir

A typical three-phase submerged-arc furnace for production of silicon metal and ferrosilicon has arc currents ~100 kA, phase voltages ~100 V and total furnace power ~10 - 60 MW. The arcs burn in gas filled cavities or "craters", where the main atomic components of the plasma mixture are silicon, oxygen and carbon. Two quite different simulation models for high-current AC arcs have been developed: the simple Channel Arc Model (CAM), and the more sophisticated Magneto-Fluid-Dynamic Model (MFD). These models have been described extensively and results reported at INFACON-8 and INFACON-9, respectively. The coupling between the arcs and the AC power source is described by a complete three-phase Electric Circuit Model. Recent numerical modelling studies of industrial AC arcs show that the boundary conditions at the cathode and anode are critical for the simulation results. A novel Cathode/Anode Sub-Model for high-current AC arcs that treats both cathode and anode indicates a completely different cathode behaviour than previously assumed. A cathode spot which serves a high-current electric arc is shown to be dominated by the energy impact from the arc. This leads to lower cathode fall voltage than obtained from previously developed models. The anode fall voltage is negative, as the main function of the potential barrier is to repel plasma electrons. The cathode spot is diffuse in the sense that the arc in fact contracts away from the cathode. Simulation results are compared to measurements on both industrial furnaces and smaller scale pilot furnaces. An important conclusion, supported by our arc studies, is that the arc length in silicon metal and ferrosilicon furnaces does not exceed 15 cm and the arc may burn anywhere on the electrode, not necessarily beneath the electrode tip.

Jan 1, 2004

By B. Asbury, M. Cigla, C. Balci

The Western Mining Resource Center (WMRC) at the Colorado School of Mines (CSM) received a grant from the National Institute for Occupational Safety and Health (NIOSH) to perform a study that will help reduce the amount of respirable dust generated from the cutting of coal. The study is based upon laboratory testing and field experience. This information is being used to develop a new cutterhead design in conjunction with Joy Mining Machinery. The new cutterhead design is being evaluated with existing computer models developed at CSM. The new continuous miner cutterhead will be tested at the Twenty Mile Coal Company’s Foidal Creek Mine. Baseline testing with the current cutterhead will also be performed. This paper presents laboratory test results, design methodology, and test results performed to date.

Jan 1, 2002

By M. Xian, M. Jahazi, Y. L. Lin

The 2-mm butt joints of ZE41A-T5 sand castings were laser welded at different defocusing distances on two surface conditions (as-cast or machined) using a continuous wave 4 kW Nd:YAG laser system at a power of 2.5 kW and a welding speed of 6.0 m/min. Two welding modes (conduction or keyhole) have been observed. The adjustment of defocusing distance can greatly influence the establishment of conduction or keyhole modes. On the machined surface conditions conduction welding is obtained at a power density of 4.0 x 105 W/cm2. In contrast, keyhole welding is reached at a threshold irradiance of 1.5 x 106 W/cm2. Neither conduction nor stable keyhole modes have been established at a range of power density from 7.7 x 105 to 1.2 x 106 W/cm2 on the machined surface conditions. On the as-cast surface conditions keyhole is obtained at a power density as low as 4.0 x 105 W/cm2 but good surface quality is obtained at a defocusing of +2 mm. The as-cast surfaces require lower power irradiance for the formation of keyholes indicating that they have higher energy absorptivity for Nd:YAG laser beams probably due to coarse surface morphology.

Jan 1, 2004

By A N. Kasnanto, D A. Sims, J Pocoe, B Pulungan

In this case study we compare the sampling quality of diamond drilling (DD) and reverse circulation (RC) drilling at the high sulfidation Purnama gold–silver (Au-Ag) deposit located in northern Sumatra, Indonesia.There was a systematic bias of 23 per cent gold metal under-call in the diamond drilling based Ore Reserve estimate compared to the mill reconciliation over three years of production. The RC based Grade Control data and mill production data were in much closer accord. Investigation led to quantification of the significantly reduced sampling imprecision (or improved precision) of RC drilling samples relative to diamond drilling samples and the determination of a grade bias between the drill types caused by sample volume and metal distribution in the mineralisation. An infill RC drilling program was undertaken to improve data density across the pit for inclusion in the Mineral Resource estimate. This subsequently increased Au metal in the estimate by 16 per cent.The sampling imprecision of primary diamond drill sampling is rarely tested. Duplicate sampling can be used to quantify sampling imprecision at each stage of subsampling. In diamond drilling it is tested at the primary sampling stage via second half core sampling, while RC sampling is tested with field duplicate sampling at the rig. Duplicate data can be compared in a number of ways to determine imprecision including Thompson-Howarth plots which quantify imprecision to allow comparison between different methods and protocols. Comparing sampling imprecision between data sets and data types allows determination of optimum drilling and sampling protocols and can reflect upon the underlying validity of Mineral Resource input data and estimation outputs.CITATION:Sims, D A, Pocoe, J, Kasnanto, A N and Pulungan, B, 2017. Why combine reverse circulation and diamond drilling in Mineral Resource estimation at Purnama?, in Proceedings Tenth International Mining Geology Conference 2017, pp 413–422 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

Various reagents are added to flotation pulps to manipulate the chemical environment in order to create favourable conditions for the separation of the desired mineral from the unwanted gangue. Interactions occur between these reagents and between the other chemical parameters existing in the flotation pulp which complicate the elucidation of the behaviour of the respective reagents. This paper discusses the roles of the main classes of reagents added viz. collectors, frothers, depressants and activators, as well as the interactions between frothers and collectors. A case study reporting synergistic interactions between thiol collectors in the flotation of pyrite at pH = 4 is included. The use of Potassium n-butyl xanthate (PNBX) and a dithiocarbamate type collector (DTC) were tested both as pure collectors and as components in a collector mixture. In the batch flotation tests sulphur recovery and grade, water recovery, rate of recovery and image analysis of the surface froth were used to evaluate the effect of the mixture on the overall flotation performance. Bubble loading tests showed that the use of the mixture improved the efficiency of the particle collection process by bubbles. Thermochemical measurements of the adsorption of the collectors onto the mineral, indicated the formation of different surface products by the two collectors.

Jan 1, 1998

By Paul Semple

"In 2007, Noront Resources Inc. discovered the high grade nickel copper PGE deposit in northwestern Ontario in a region now known as the Ring of Fire. Since the initial discovery, Noront has advanced the Eagle¹s Nest Project and in September 2012 released a feasibility study for the development of the Eagle¹s Nest Project. This paper summarizes the results of this recent study and outlines additional work planned in the next stages of project development. INTRODUCTIONThe following paper summarizes the findings of the recently completed feasibility study on Noront Resources Ltd.’s Eagle’s Nest Project. The feasibility study was compiled into a NI 43-101 report by Micon International. This paper is intended to summarize the major technical findings and for complete information, interested parties can find the entire NI 43-101 report at www.norontresources.com or on SEDAR.LOCATIONThe McFaulds Lake project area, which includes the Eagle’s Nest deposit, is located at approximately UTM 5844000 N and 547000 E, and between approximately 52º42’ and 52º50’ N latitude and 86º06’ and 86º24’ W longitude, approximately 250 km west of the community of Attawapiskat on James Bay and 575 km northwest of Timmins. The closest all-season accessible community to the McFaulds Lake project area is Nakina, 300 km to the south, where there is a paved airstrip, in addition to all weather road and railroad access (see Figure 1).The First Nations communities of Webequie and Ogoki/Marten Falls are located 90 km west and 120 km south southeast of McFaulds Lake, respectively. Both communities are served by regularly scheduled air service, primarily from Thunder Bay; both Thunder Bay and Timmins serve as support centres for the James Bay communities and the exploration projects in the area."

Jan 1, 2013

By N. I. Basuki, E. T. C. Spooner

"The Bongara area, northern Peru, contains Zn-Pb mineralization with characteristics typical of Mississippi Valley-type (MVT) systems. The northwest-southeast-trending late Triassic-Jurassic car¬bonate host rocks of the Pucará Group were locally replaced by early (D1) and late (D2) dolomite. Fluid inclusion microthermometric data from dolomite and sphalerite are typical of MVT ore fluids (78° to 187°C; ~15-23 wt.% CaCl2 equivalent), and do not show apparent covariation between temperature and salinity.Homogenization temperature data from D1 and D2 dolomite show a decrease from northern (mean Th = 138°C) to central (mean Th = 126°C) to southern areas (mean Th = 102°C), suggesting fluid flow from north to south. Assuming a geothermal gradient of ~30°C/km and an average surface temperature of ~20°C, the lower temperature limits might approximate the ambient host-rock temperatures, whereas the upper temperature limits may represent minimum temperatures of a deeper aquifer, probably at a maximum depth of ~6000 m. The lower temperature limits are also similar to the estimated temperatures if dolomitization and mineralization took place in the Late Cretaceous at ~2000-3000 m depth, probably during the formation of the Peruvian fold and thrust belt near the present day Peru-Ecuador border.Fluid inclusion data show that the fluids in each studied location had relatively uniform temperatures and salinities during dolomitization and mineralization. A significant salinity drop and a slight temperature decrease are observed during late calcite precipitation, suggesting mixing of brines with dilute, cooler fluids."

Jan 1, 2009

By T. W. Peglas, J. Doherty, R. A. Day

The South East Transit Project is a $520 million project in Brisbane, Australia which includes the construction of a 32 km Busway to access the south-eastern suburbs. Close to the centre of Brisbane, tunneling techniques have been used to minimise surface disruption. This paper describes some of the features of the longest driven tunnel on the project, the Vulture Street Tunnel. The Busway is a two lane expressway for buses which requires a 10.2 m finished width and a 12.6 m excavated span of driven tunnel. The Vulture Street Tunnel carries the Busway at minimal cover beneath the operating Vulture Street Railway Station, beneath a three storey office building and beneath the roadway to the Mater Hill Busway station. Halfway along the route, a Y-junction has been constructed to enable future connection with a light rail route. Key features in the design and construction of the Vulture Street Tunnel include: Use of canopy tubes to drive a 12 m wide tunnel beneath operating railway tracks with less than two metres of cover in highly weathered rock. Underpinning the office building in the route of the tunnel construction from within the building carpark. Construction of a 24 m span Y-junction with 7 metres cover of weathered and faulted rock. Use of predictive analysis as an adjunct to traditional back analysis to estimate the tunnel settlements from pressuremeter test results. This paper describes the design methodology with particular reference to settlement prediction, as well as construction innovations used to complete the tunnel. This paper will be of interest to all designers who have to create large spans in minimal cover in weak rock in urban areas and who have to predict the settlement

Jan 1, 2001

This paper describes the new legislative regime that will apply to the regulation of the minerals industry in New Zealand. The reform of New ZealandÆs minerals legislation was initiated in January 1988 when the Minister for the Environment, Rt Hon Geoffrey Palmer, announced the Governments intention to review all the major laws governing New ZealandÆs resources. The Resource Management Bill is scheduled for introduction to the House in December 1989 and its date of enactment is scheduled for June 1990. With some matters still to be determined (at the time of writing), this paper cannot be a definitive review and description of the new legislation, it is instead an attempt to outline the major features of the Bill, to date, that are seen as important to the mining industry.

Jan 1, 1990

By Peter Faust

The foundations for the new South Viaduct Bridge in San Francisco were extremely challenging due to the requirement for very large and deep piles installed adjacent to historic structures. Drilled shafts up to 12? foot in diameter were constructed to a maximum depth of 200? feet in alluvial soils and Franciscan Bedrock using an oscillator system for the installation of the permanent steel casing. This paper provides an overview of the construction techniques, the equipment, and the challenges associated with constructing 12? foot diameter shafts on this very complex project in one of the nation?s nicest landscape setting.

Jan 1, 2011

By Walter E. Vanderpool

Full scale load tests are frequently performed immediately prior to deep foundation construction to verify the design assumptions. Occasionally, load tests are performed during design development and applied to the final design for critical and non-redundant structures. We believe that full scale load tests can be very valuable and economical for projects, especially in a geologic environment where the record of full scale load testing is very limited or non-existent. The load testing for the Utah Transit Authority?s Airport Light Rail Trax project provides an example of the advantages of a load test in design development. The savings realized by the owner was in excess of $800 thousand dollars.

Jan 1, 2011

By Elizabeth M. Smith

The kcICON design-build project in Kansas City, Missouri includes widening the existing roadway, improving interchanges and grade separation bridges, and replacing the Missouri River Bridge. The Missouri Department of Transportation (MoDOT) typically utilizes steel H-piles and steel pipe piles as driven pile support for bridges. After bidding the kcICON project, the cost of steel rose significantly and the design-build contractor used an innovative approach to reduce foundation costs without significantly affecting the project schedule. The kcICON team conducted a value engineering evaluation of alternative foundation types for use at four grade separation structures. The result of the value engineering evaluation was selection of precast, pre-stressed concrete (PPC) piles as the preferred foundation alternative. Terracon developed a test program to evaluate the performance, capacity, and suitability of PPC piles at the site using a PDA and CAPWAP analyses. This paper presents the value engineering design, rationale for selection of PPC piles, results of the pile test program, and findings during production pile driving. The collaborative approach to the project by MoDOT and the kcICON team, combined with testing and a site-specific design approach, resulted in substantial savings for the design-build contractor.

Jan 1, 2009

By Detlef Ehlert

In view of the increasing level of cost pressure on the part of plant owners, optimized plant operation with top product quality and maintenance costs is indispensable. Unscheduled shutdowns with increased repair costs and production downtimes are significantly reduced by preventive maintenance and the stock-keeping of spare parts. To remain competitive in the steel market, it is important for plants owners to operate their plants with the highest possible degree of energy efficiency and at high availability in order to manufacture high-quality products. Plant Monitoring Systems make it possible to optimize the manner of production. An integrated overview of the overall process, under consideration of process stability, product quality, production costs and plant availability ensures a “transparent plant”.

Aug 16, 2017

By Y Yamaguchi, S Nomura, M Matsumura, C Kamijo

In order to increase productivity and decrease reducing agent rate (RAR) of blast furnaces, slag content of sinter ore must be decreased. However, gangue content in iron ore tends to increase because of resource depletion. Therefore, amount of high-grade concentrate in sinter ore feeds should be increased, but this situation causes a decrease in permeability of the sintering bed so that the productivity of sinter process decreases. In order to increase the amount of concentrate, NSSMS has developed the P-type separate granulation method, RF-MEBIOS and SPEx II technologies. These technologies have been introduced to actual sintering machines. In this report, a new technology using microparticles of iron ore is proposed to increase the amount of concentrate in sinter blends. Basic experiments simulating the sinter making process using microparticles of iron ore were undertaken. Crushed pisolite, containing >60 wt per cent -10 µm was prepared for binder. The pisolite microparticle binder was mixed with another Australian sinter feed ore in a high-speed agitating mixer. They were mixed for about one minute, and then granulated using a pan pelletiser. After that, they were added to another raw material mixed by a drum mixer, and then charged in a pot for a sinter pot test. As a result, when the amount of concentrate increased from 13 wt per cent to 20 wt per cent, productivity was almost kept constant using pisolite microparticle binder.CITATION:Kamijo, C, Yamaguchi, Y, Matsumura, M, Kawaguchi, T and Nomura, S, 2017. Development of an iron ore microparticle binder for increasing the concentrate content of sinter blends, in Proceedings Iron Ore 2017, pp 69–74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Mark R. Svinkin

Regulations are needed to keep construction vibrations in tolerable limits. The existing regulations were developed for low-rise residential structures, but they are incorrectly used for different super and underground structures. The existing regulations cannot prevent most of harmful vibration effects on sensitive devices, people and structures from construction and industrial vibration sources. It is important to determine the areas of application of the existing regulations and bring attention to the necessity of measurement of the structural responses for assessment of vibration effects on structures. For multi-story residential, commercial and industrial buildings, the frequency-independent safe limit of 51 mm/s (2 in./s) can be chosen for the peak particle velocity of structural, not ground, vibrations. Specifications for construction operations with dynamic sources have to consider specifics of each construction site. Preventive measures can be used to mitigate harmful vibration effects on various structures and settlements in sand and clay soils.

Jan 1, 2006

It is now becoming mandatory in Australia to rehabilitate ponded fine grained coal mine tailings, which may well have been deposited initially with no consideration as to how or whether this could be done nor to the costsinvolved. Of prime importance to the rehabilitation of tailings ponds are the bearing capacity and deformation characteristics of the tailings. Since the tailings are fine grained, time effects will govern the self-weightdeformation of the tailings initially deposited as a slurry and the subsequent deformation of the deposit under the weight imposed by rehabilitation fill. The engineering properties of a particular deposit of ponded tailings havebeen investigated and its response to the placement of fill monitored and analysed.

Jan 1, 1987

By J. A. Hudson, X. D. Pan

A rock mass responds to excavation according to the properties of the intact rock, the network of contained discontinuities and the susceptibility of the rock mass to weathering. Large deformation often occurs when one of these components causes the rock mass to have a low strength relative to the stress conditions. Analysis of such large deformations forms a significant feature of current numerical modelling in rock mechanics. A practical large deformation problem of roadways in a coal mine is described, demonstrating the requirements for improving numerical techniques. The development of a numerical model is then summarised with particular attention to several concepts pertinent to large deformation analysis in geomechanics. A numerical case study is presented in which the developed finite-element model is used and the results are compared with the in-situ measurements. Conclusions are drawn for rock engineering that are also relevant to both civil engineering and mining engineering projects

Sep 1, 1991

By William Paxton Hewitt

In the Santa Eulalia mining district, Chihuahua, Mexico, the main mineral zone occurs in a gently warped dome with simple associated structures and contains orebodies distributed through a vertical range of over 900 m. The stratigraphy of 1945 m of geologic column is described and an abrupt shrinkage is documented in the volume of limestones immediately associated with large orebodies. Termed collapse, this shrinkage occurred during the course of mineralization. Contacts of limestone with igneous sills, and 366 m of fossiliferous limestone beds, particularly the main fossil bed, have been important localizers of ore-bodies. Up-dip gravitational controls may have been important. Fractures have exerted only local controls and over short distances. Thrust zones have displaced diabase sills and in turn have been intruded by upper members of a group of rhyolite porphyry sills. Mineralizers were related to the rhyolite porphyry, and ore has been introduced to the limestone where certain sills lie between the displaced segments of diabase and have been cut by north-south fissures. Speculations are raised that fields of unreleased strain may have influenced orebody locations; the district's zoning pattern may be a reflection of the filtering effects of large volumes of limestone; and that metal-rich brines mobilized by or incorporated within the invading porphyry might be the source of the mineralizers. PRODUCTION AND LOCATION The Santa Eulalia district has a production record approaching or exceeding 35 million tons of silver-lead-zinc ore from replacement bodies in limestone. In operation since the first years of the 17001s, production has been confined to two intensely mineralized areas separated by 2 km of barren limestone, the West Camp and the East Camp. Probably 50% has been mined since 1908, with over 90% from the West Camp. The West Camp, exploited through a vertical depth of 1945 m and now approaching exhaustion, is the subject of this paper. The district lies in the northern part of the Santa Eulalia Mountains in central Chihuahua in northern Mexico, 400 km south of El Paso, Texas, and 22 km southeast of Chihuahua City. Dominating the northern part of the range is the Cerro de Santa Eulalia, a broad rolling upland which contains the district's West and East Camps. The West Camp, on the west side of the range, centers around the village of Santo Domingo, which is 2 km northeast of the Real de Santa Eulalia (Fig. 1). REGIONAL GEOLOGY Thick-bedded middle Cretaceous limestones, probably Aurora, form the great bulk of the Cerro de Santa Eulalia. These beds, warped into a gentle dome, are severed on the west by a faultline scarp and truncated on the north by the Dolores Pass, a wind gap that

Jan 1, 1969