Search Documents

By Charles R. Fettke

The permeability of an oil or gas sand is its capacity for transmitting fluids, either liquids or gases, under pressure. The permeability of a sand depends upon the size and shape of the openings in it and the extent to which these communicate with one another, as well as upon the ratio of their volume to the total volume of the sand. The apparatus employed and the method of procedure used by the authors in conducting the permeability tests have been described in a previous pub1ication.l For the tests described here 1/2-in. cubes were used. They were set in the lower end of a 1-in. union, inserted in a square hole cut in a hard rubber stopper which fitted into the lower end of the union. In the tests with air, volumes were measured with a wet American gas meter of 100 cu. ft. capacity. In those with water, distilled water at room temperature was employed, unless otherwise noted. DescRiption of Sands Tested The tests described in this paper were performed upon 18 samples representing typical oil and gas sands from 7 localities in northwestern Pennsylvania. For purposes of identification, the cores from which the samples came have been designated by capital letters, the sequence of the samples in the cores by numerals, and the individual cubes by small letters. All cubes from the same samples came from adjacent portions parallel to the bedding. Core A of the Bradford sand came from the north central part of the Bradford field, from an area where water-flooding operations have proved highly successful. Core B of the same sand was obtained from the southern part of the field. This core contained a so-called "loose streak," 7.5 ft. thick, in the middle portion of which B2 is a representative sample. The "loose streak" has given trouble in water-flooding but responded favorably to an air-drive, using a pressure of 300 lb. The natural production was increased approximately five times over a period of three years in which the air-drive was in operation. Core C, also of the Brad-

Jan 1, 1931

By Barry R. Doyle, Emma C. Ross

This paper presents a 20-year global account of tunneling in gassy ground demonstrating high probability of schedule delays, cost overruns, worker injuries and fatalities. Causes of these failures are systemic. Gas is seldom characterized in terms relevant to design of effective ventilation systems. Control measures deployed in tunnels are often based on outdated industrial safety codes. A change in approach is needed. This paper describes how to perform a desk study to determine if field investigation for gas is warranted, and lists the content of an effective characterization of gas in a geotechnical report.

Dec 1, 2022

No. 484.-A mining engineer and geologist of long and varied experience in North and South America is open for an engagement. Exploration and development work preferred. Rare minerals a specialty. No. 485.-Member, mining engineer, technical graduate, married, age 28, exempt, with 9 years experience at gold and silver, copper, lead, and coal mines, 4 years with present employers, is open for engagement as mine superintendent or foreman, or in charge of cyanide plant. Boston or New York interview after Oct. 10. Present position, day foreman at producing gold-silver mine in Montana. References. No. 486.-Member, age 34, married, varied experience in iron, copper, nickel, talc, etc., principally as surveyor, mine and surface geologist, and superintendent of explorations, is open for engagement. Preference, connection with some eastern consulting engineer or firm of engineers. No. 487.-Member, mine superintendent, 18 years' experience in the West and in the Lake Superior districts. Thorough business and technical training. Personal interview, preferably Chicago.

Jan 10, 1918

By A. J. Richins, M. G. Nelson, R. Dunne

From the inception of flotation in the late 1800s, coarse particle recovery has been a challenge to practitioners. By the early 1900s, flotation processes included oil flotation, skin flotation, agglomeration flotation, and froth flotation, and for each there was a proliferation of flotation equipment. Ensuring good coarse particle recovery included desliming of the feed and proper conditioning were required. Froth flotation was at first used mainly to treat finer materials from grinding circuits. The maximum size for coarse particles was from 3.18 to 4.78 mm. In froth flotation, large particles with high specific gravity tend not to be recovered. Coal and minerals of low specific gravity and flaky minerals such as graphite, mica, and talc can be floated in larger sizes. In the early 1960s, the phosphate industry began using column cells to recover coarse particle by froth flotation, but early columns suffered from poor bubble generation and sanding at the flat base of the column. Recently, improved coarse particle recovery has been the object of new cell designs—the Eriez HydroFloat™, the Jord NovaCell™, the FLS coarseAir™ cell, and the Cidra P29 integrated system. The paper will follow the development of coarse particle flotation with a focus on the development, laboratory assessment, and operation of the new flotation equipment and technology designed to recover coarse particles.

Feb 22, 2026

This paper reviews hydrometallurgical processing technology for refractory gold ores, which form an increasing resource stock for gold. The reasons fQr ore refractoriness and pressure, chemical and biooxidation process options are briefly listed. Electrochemical technology, suitable for processing refractory ore is reviewed and some preliminary results for the electrochemical oxidation of slurried arsenopyrite are given.

Jan 1, 1992

By D. J. Dunn, J. L. Huiatt, T. E. Norman

Corrosion studies in laboratory ball mills and grinding environment simulations produce corrision rates and total metal removal rates much lower than those recorded in operating production ball mills. The corrosion component of ball metal loss in many mills probably represents less than 10% of the total loss, judging from AMAX experience and recent US Bureau of Mines (USBM) tests. Such small absolute losses are consistent with ball metal loss measured in production ball mill marked ball wear tests to determine effects of corrosion and abrasion resisting properties of alloys in operating mills. These indicate that metal hardness and microstructure determine relative metal loss rates of a given situation. The combination of ore characteristics and grinding process dynamics determine metal loss severity. Alloying for corrosion resistance and modification of the milling corrosion environment yield relatively small metal loss reductions. Alloying and heat treatment to produce high hardness and microstructures of high carbon martensite and, for cast irons M7C3 carbides, produces the lowest metal losses in typical wet grinding applications.

Jan 1, 1986

By J. P. Savely

This paper describes the development of a trim blast design to improve the stability of a final pit wall. Description is given of the effects of rock characteristics, rock type, and pit plans on the blast design. Currently, six benches have been mined with trim blasting. A more stable final wall has resulted and the successful program has reduced mining costs over an extended time period. Low-cost blast monitoring and field observation were used to determine peak particle velocity and blast damage. Using criteria developed from this relationship, trim blasts were designed and evaluated.

Jan 1, 1987

By C. H. Madsen

THE Hard Rock gold mine is in the Little Long Lac mining area, Thunder Bay district, northwestern Ontario. It is four miles by road from the town of Geraldton, which is on the Canadian National railway, 180 miles northeast of Port Arthur. The original discovery of gold-bearing quartz veins on the property was made in 1931. Shaft sinking began in the fall of 1934 and approximately 7,400 feet of lateral development on four levels was completed. In 1935, further discoveries were made half a mile west of the early workings, and the No. 2 shaft was sunk in this area in a porphyry zone. In January, 1938, a 20C-ton cyanide plant was completed and began drilling ore from the gold-bearing porphyry orebody. The daily feed was increased gradually to 300 tons in the next six months and a recovery of 97.5 per cent was effected. During the summer of the same year, a new and larger orebody was discovered to the north of the porphyry zone. It occurs in a band of iron formation and contains a high percentage of pyrite and arsenopyrite. Extensive tests were rr.ace on this sulphide ore in the Mines Branch ore dressing laboratory at Ottawa, in the laboratory of Canadian Industries, limited, at Toronto, and later at the mine, to find a suitable method of treatrr.ent. As a result of this research, a Potation plant was added to the original cyanide mill and on November 7th, 1938, differential flotation was used to separate the pyrite from the arsenopyrite fraction of the ore. The pyrite concentrate was re-ground and cyanide:l, and the arsenopyrire concentrate was stored for subsequent treatment. Differential flotation was discontinued in April, 1939, in favour of bulk formation of all the sulphides, and the whole cyanide residue was stored. On March 15th, 1939, a 10-ton pilot roaster was completed and rests were conducted on the arsenopyrite concentrate and the bulk concentrate. The results obtained led to the building of two roasters of the same type, large enough to roast all the concentrates. These roasters were put in operation on September 24th, 1939, and the calcines were cyanided in the original circuit.

Jan 1, 1941

By R. G. Diale, H. R. Chauke, T. M. Ledwaba, P. E. Ngoepe

FeCo alloys play an important role in soft magnetic materials with a wide range of technological applications due to their high saturation magnetization and Curie temperature. However, these alloys have low ductility at room temperature. The ductility can be improved by the ternary addition of elements such as V. A density functional theory supercell approach was used to generate B2 Fe50Co50-xVx (0 ≤ x ≤ 50) structures and the properties were evaluated at different atomic percentage compositions to determine the ductility at room temperature. The structures were fully optimized to obtain better equilibrium ground-state properties such as lattice parameters and thermodynamic properties for both binary and ternary systems. The stability of Fe50Co50- xVx was evaluated from the heats of formation, elastic properties, and phonon dispersion curves. Furthermore, magnetic strength was evaluated from magnetic moments. It was found that all structures are thermodynamically stable due to the negative heats of formation. The calculated Pugh’s ratio and Poisson’s ratio confirm that alloying with V effectively improved the ductility. It was also found that Fe50Co50-xVx showed a positive shear modulus for the entire concentration range investigated, in agreement with phonon dispersion curves. The ternary addition of V to the FeCo system resulted in reduced magnetic strength due to a decrease in magnetic moments. These findings reveal that B2 FeCo-V alloys can be used as components and actuators for the automotive industry.

Jun 10, 2024

During the year 1915 the Committee received 161 manuscripts, which were treated as follows: 3 accepted for. New York Meeting (110th) . 64 accepted for San Francisco Meeting (111th) 49 accepted for New York Meeting (112th) 3 accepted for Arizona Meeting (113th) 29 rejected 4 returned to authors for revision and not yet accepted 9 in committee. 161 Every paper which was presented at the San Francisco Meeting was published in advance in the Bulletin with one exception. The work of the Committee has been systematized and. the Executive Committee of the Committee on Papers and Publications has given prompt attention to all manuscripts, with the result that every paper received by the Committee on Papers and Publications is in the hands of the, printer within 30 days thereafter, unless delays occur owing to questions as to acceptability, in obtaining from the author permission for revision, or other like causes.

Jan 2, 1916

By B. Ramaswami, U. F. Kocks, B. Chalmers

The latent hardening of silver and an Ag-Au alloy was investigated by lateral compression, overshoot in tension and cormpression, and the stability of multiple-slib orientations. The latent hardening of a secondary slip systenz depends on its relation to the primary slip system. For most secondary slip systems the latent hardening is larger for Ag-10 at. pct Au than for pure silver. The maximum increase in. flow stress on a secondary slip system over that of the primary slip system was 40 pct. The work hardening during the lateral-compression test on the latent system after prestress on the primary system is iuterbreted in terms of the preferential distribution of barriers to dislocation movement with respect to the active slip system in work-lzardened fcc crystals. The work-hardening in fcc crystals is mainly due to the dislocation interactions and the barriers to dislocation movement formed as a result of reactions between dislocations of different slip systems. The operation of sources on the latent system depends on the flow stress of those systems; hence, the increase in flow stress of a latent system due to glide on an active system, which is called latent hardening, is an important element in understanding the phenomenon of work hardening. The problem of latent hardening has attracted the attention of many investigators in the past. For example, a theoretical study of the elastic latent hardening of the latent systems due to glide on an operative system has been made by Haasen' and ~troh. These calculations, however, neglect the stress required for the intersection of forest dislocations by the glide dislocations, a factor which would be important for producing macroscopic strains on the secondary slip systems. The importance of this factor will become evident from the results presented here. Attempts have also been made to determine the latent hardening of different slip systems by experimental means by the methods summarized in Table I.3-9 The experimental methods used have been subject to certain limitations. For instance, in the method used by Hauser,9 frictional constraints between the specimen and the compression platen were not eliminated by proper lubrication (see Hos- ford10). Secondly, with the exception of Kocks,6 Hauser,9 and Rohm and Kochendorfer,11 latent-hardening studies have been made on only one of the slip systems, i.e., on either the conjugate or the coplanar slip system; hence, extensive results are not available on the latent hardening of different slip systems in the same materials, with the exception of aluminum.6 It was therefore decided to study the latent hardening of the conjugate, critical and half-related slip systems in silver. Similar experiments were done in Ag-10 at. pct Au to study the effect of solute (gold) on the latent hardening of silver. Lastly, indirect evidence can be obtained by a study of the orientation stability of crystals of multiple-slip orientations in tension and compression. This method has been used by Kocks6 to supplement his studies of latent hardening in aluminum. Similar studies were made at room temperature in single crystals of silver. EXPERIMENTAL PROCEDURE The single crystals of the desired orientations were grown and the tensile test specimens were prepared as described in Ref. 12. The compression tests were made on 1/4-in.-cube specimens. The specimens were cut from single crystals, in the Servomet spark-erosion machine.13 The two cut surfaces were planed using the lowest available planing rate in the machine to minimize the deformation layer. A brass strip was used as the planing tool. This method of preparation ensured plane parallel faces for the compression tests. The deformed material was removed by prolonged etching in a weak etching solution. A weak etching solution was used to prevent pitting of the surfaces and to ensure uniform etching. About 25 to 50 µ of material were removed from all faces by the etching treatment. The specimens were then annealed for 24 hr at 940°C in oxygen-free helium and cooled in the furnace to room temperature over a period of 7 hr. After annealing, the orientation of the specimens was determined by Laue back-reflection technique to make sure that no recrystallization had occurred on annealing. The compression-test technique and setup are described in Ref. 14. The Laue back-reflection technique was used to study the overshoot in tension, the overshoot in compression, and the stability of the axial orientation in tension and compression. The tests were interrupted after every few percent strain to determine the axial orientation. In investigating the overshoot in compression, the operative system was determined by studying the asterism of the Laue spots.

Jan 1, 1965

The mechanism of thiosulfate decomposition and the products formed were investigated in the presence of pyrite or pyrrhotite in copper-ammonia solutions used for leaching gold. The presence of the sulfides significantly increased the decomposition of thiosulfate. The sulfide-surface-catalyzed oxidation of thiosulfate to tetrathionate by dissolved oxygen or the cupric tetra-ammine complex was proposed to be the dominant thiosulfate decomposition mechanism. The catalysis of the sulfides in this reaction could originate from their strong affinity for aqueous sulfur species and their semiconducting properties. Oxygen was found to be the initial driving force for thiosulfate decomposition in the absence of cupric ions and the driving force for the continuous decomposition of thiosulfate in the presence of cupric ions. Under an oxygen free atmosphere, the decomposition of thiosulfate was limited to reduce the cupric ions and the catalytic effect of the sulfides was also marginal. The dominant oxidative product of thiosulfate was trithionate in alkaline solutions especially in an oxygen rich or cupric ion rich environment. Tetrathionate was found in relatively smaller amounts in an oxygen and cupric ion deficient environment. Tetrathionate was not stable and would further decompose after extended periods. Trithionate concentrations increased almost linearly with time.

Jan 1, 2005

By Henderson N, Schaap H

In large companies with mining operations spread over multiple sites, it is essential that consistency between sites is maintained in preparing and classifying resource and reserve estimates. The endorsement by The AusLMM and AMIC of the "Australasian Code for Reporting of Identified Mineral Resources and Ore Reserves" and the subsequent incorporation of reference to the code into the ASX listing rules for mining companies has provided a basis for the consistent classification of resources and reserves. However, compliance with other criteria more or less stringent than the Australasian Code can present some reporting difficulties. Examples include listing requirements for foreign stock exchanges, particular Acts of Parliament that may apply to individual leases, constraints imposed by individual companies on their own leases, and ultimately, reserves for short, medium and long term planning. Confusion can arise when any two or more sets of reserves for the same lease are compared.. To alleviate this confusion, a standardised procedure was developed for the calculation and classification of coal resources and reserves. The procedure which is geostatistically based incorporates a technique called "Irregular Block Kriging" where specific mining blocks are directly kriged. The procedure has enabled those engineers and geologists with only a basic understanding of geostatistics to apply the technique and not feel hampered by some of the complex mathematics which in the past has tended to inhibit and overcomplicate the use of geostatistics. The procedure has resulted in "cleaner" data bases and hence more reliable reserve estimates.

Jan 1, 1990

From statistics on general and electrical fatalities in the Australian mineral industry, it could be said that the present approach to industrial safety is irrational. Deaths are few and decreasing in number, yet spend- ing on occupational safety is large and increasing. State mine safety inspec- torates are being expanded and a National Occupational Health and Safety Commission was recently established. Recent data are analysed in the paper and mining industry fatalities placed in perspective with deaths in other areas. Cost effectiveness of different strategies is discussed along with social implications. Strategies found successful are described and others suggested.,

Jan 1, 1988

By J. D. Miller, M. Misra

The processing strategy for the effective separation of bitumen from low grade (<l0 weight percent bitumen) Utah tar sands by a hot water process differs significantly from that used for the processing of high grade (> 10 weight percent bitumen) Utah tar sands. Excellent separations (coefficient of separation = 0.9) can be achieved for high grade Utah tar sands by intense hot water digestion followed by a modified froth flotation step. Such a technique is ineffective for low grade tar sands. In order to change the characteristics of the low grade tar sand an attempt was made to enrich the bitumen content of the feed to greater than 10 weight percent by recycle of bitumen concentrate to the digestion stage. However, the quality of the separation was not improved under these circumstances. Similarly feed enrichment by heat treating the low grade feed with recycled concentrate prior to digestion did not improve the separation. More successful separations of low grade Utah tar sands were finally achieved by modification of the viscosity of the low grade bitumen with controlled addition of diluent. These results of the hot water separation tests and variations in the quality of separation are interpreted in terms of the physical properties of the bitumen and the surface bonding forces operative at the bitumen-sand interface.

Jan 1, 1981

By M. Takebayashi, K. Takenaka, S. Matsubara, T. Yoneyama

The cathode production of Toyo Smelter and Refinery, owned by Sumitomo Metal Mining Co., Ltd. reached 450,000 tons per year in 2016 with three tank houses. Niihama tank house commenced operations in 1919 with conventional sheet cathode technology. Approximately 100 years of operation experience and the technical development enabled that the current density of Niihama tank house and the Toyo tank house #1 increased to 320 A/m2. These operation techniques were utilized at the Toyo tank house #2 which started in 2005, and its current density reached up to 350 A/m2 with permanent cathode technology. In order to achieve high current efficiency under condition of 350 A/m2 operation at Toyo tank house #2, continued efforts had been made to verticality of anodes and permanent cathodes. To improve verticality of anodes and cathodes, reduction of short circuit ratio by changing the shape of the anode, optimizing the anode pressing machine and off-line process for rectifying the distortion of permanent cathodes was carried out. In addition, concentration control of electrolyte and expansion of Ni removing ability from the electrolyte prevented passivation. Finally, more than 96% of the current efficiency was stably confirmed. INTRODUCTION Today, Toyo Smelter and Refinery of Sumitomo Metal Mining operates three tank houses in Japan, namely, Toyo tank house #1, Toyo tank house #2, and Niihama tank house with a total capacity of 450,000 metric tons of copper cathodes. Figure 1 shows the trend of cathode copper production and the current density at three tank houses over the last 10 years. Cathode production by Toyo Smelter and Refinery reached 450,000 tons per year in 2016 with three tank houses.

Jan 1, 2019

By J. B. Littlefield

[Ata. meeting of the Subcommi ttce on Chemical _ et.lOds of Air Ant:..1ysis of-the American Public Health Ascociation in October 1937, the llse of the impinger for collectinG lcs.d fu.l1e wa:., discussed. The Bureau of Mnes de-cided to obtain infornw.tion on the efficiency of the lerge and midget im-pingers for this purpose y using the electric recipitator as a reference method. &apos;I&apos;ests ~ ere made aJ,so to aScer ain the effici ency of the recently developed midget i;npi gerS..! for collac ing lead dust. For comparative pur-poses, samples collected by tte large impinger wore included.]

Jan 1, 1938

By Norman A. Jull, A. L. Mular

Fundamentals of cyclones are reviewed briefly, where a typical cyclone is considered. Graphical cyclone data available in the literature have been converted to mathematical equations for convenience. Preliminary selection and design procedures for both cyclones and pumps are provided, and a sample calculation for a hypothetical grinding circuit is covered in some detail. In general, cyclone and pump suppliers should be consulted for definitive design purposes. Some cyclone suppliers currently employ digital computers for definitive design to ensure greater accuracy.

Jan 1, 1978

By S. Downing, T. Grammatikopoulos, N. Hoffmann, C. Gunning

"Most deposits display a high degree of geological and mineralogical complexity that can affect metallurgical processing. Therefore, the proper characterization of the ore and gangue minerals requires a multi disciplinary approach combining geology, mineralogy, geochemistry and processing. However, mineralogy to a large extent informs the metallurgical process. Automated methods can be used throughout the mining chain from advanced exploration through to production.In this presentation we discuss actual case studies where automated mineralogy has been applied in a geometallurgical framework at a pre-feasibility to feasibility level. These include examples from a strongly serpentinized magmatic Ni deposit (Dumont) and a magmatic Cu-Ni deposit (Maturi). Mineral speciation and ratios, e.g., chalcopyrite, cubanite, and pentlandite/pyrrhotite are critical to model the Cu-Ni magmatic deposit. In the serpentinized Ni ore, automated mineralogy is used to speciate the Ni minerals into sulphides, alloys and refractory Ni in the silicate matrix.The mineralogical results are linked to the metallurgical test work in order to model the geometallurgical domains. These case studies will illustrate how mineral quantification and improved understanding of inherent mineralogical parameters in relation to metallurgy reduce technical risk in both exploration and flowsheet development.INTRODUCTIONGeometallurgy is a cross-discipline approach combining geology, metallurgy and mine planning (e.g., Dunham et al., 2011). It is aimed to improve the understanding of geological, mineralogical and metallurgical parameters of an ore. Informational gaps among the different disciplines are often apparent. Automated mineralogy is shown in many studies (e.g., Eppinger et al., 2013, Philander and Rozendaal, 2013) to constitute the link between geology and metallurgy. The geometallurgical approach can provide specific data to geology, mining and mineral processing development and plant operations. The scope of the automated mineralogy is to illustrate how mineral quantification can improve the understanding of inherent mineralogical parameters in relation to metallurgy, and reduce the technical risk in both exploration and flowsheet development."

Jan 1, 2016

By Charles A. Taschereau

Burkina Faso ? Formerly known as Upper Volta; Country is landlocked and dry (Sahel sub-Sahara zone); ? Among poorest countries in the World, according to the United Nations Human Development Index (in 2005, 178 out of 179 countries; in 2009 173 out of 179); ? Population 13,9 Millions; Life expectancy is 51.4 years; Fertility rate 6.47 children/woman; Average age is16 years; literacy rate 23.6% and GDP per capita $1,213; ? French is official language; Politically stable country; very low criminality rate; corruption level low. Multiparty elections since early 90s; Legal and political systembased on French civil law system; ? Country just opened a few years ago to International mining companies, with a new mining code and investment code; ? No experienced labour; ? All new codes and laws; no established practices; Very limited economic development, mining is already main product of exportation and the country will become with Essakane a mineral economy (over 50% of total exports from mineral sources);

May 1, 2010