Search Documents

By C. B. Daellenbach, T. D. Tiemann

The prevention of quartz flotation by chelation of activating ions with the tetrasodium salt of EDTA in oleic acid flotation was investigated using a small vacuum flotation cell. It was found that flotation of quartz could be entirely suppressed in the presence of activating ions during complete flotation of hematite. It was further shown that the concentration of activating ions liberated from Wisconsin Gogebic taconite is sufficient to float quartz in an oleic acid system. Large tonnages of low grade siliceous iron ores occur on the iron ranges of the Lake Superior district. Although the lower grade nonmagnetic types are currently not of economic importance, they constitute a large future potential source of iron and steel, and hence have been the subject for extensive research on their beneficiation. TACONITES Of particular interest to the Dept. of Minerals and Metals Engineering at the University of Wisconsin have been the low grade nonmagnetic taconites of the Wisconsin Gogebic Range. These occur as five members of the iron formation and have been described in detail elsewhere.' Essentially they consist of an intimate mixture of hematite, goethite and quartz, with minor amounts of siderite, magnetite, iron containing silicates, and manganese minerals. A typical mean analysis based on the Bureau of Mines analyses' is: SiO2-52.50%, Fe2O3-43.40%, (Fe-30.38%), A12O3-1.15%, P2O5-0.07%, Mn2O3-0.29%, CaO-0.07%, (S-0.03%), Loss on ignition-2.00%. The quartz in these ores is of a microcrystalline variety,2 and so intimately associated with the iron oxide minerals that extremely fine grinding, in the order of minus 325 mesh, is required for liberation. During grinding and subsequent flotation, the concentration of quartz activating ions in the pulp becomes sufficiently high to activate quartz which floats along with the iron minerals in the presence of oleic acid. cook3 and co-workers concluded that oxidized iron ores released appreciable quantities of quartz-activating ions in water pulps. This is shown to be true in the present investigation. As a matter of fact, application of this phenomenon, as well as the intentional addition of activating calcium ions, is made use of in the an ionic flotation of silica from the iron oxide minerals.4,5 In view of the above, it becomes almost impossible to effect a sharp separation of quartz in the oleic acid flotation of the iron oxide minerals from these taconites, even with satisfactory liberation. This fact led to the current investigation to find a means of linking the activating ions with a chelating agent. The aim was to establish basic data for the quartz-water-oleic acid system which might not only be applicable to iron ores, but also to the flotation of other siliceous ores as well. EXPERIMENTAL METHODS Vacuum Flotation Cell: The vacuum flotation used in this investigation is similar to that used by previous investigators.6,7,8 The cell consisted of a 100 ml graduated cylinder with the lip removed. Vacuum from a water aspirator was applied to the cell through a trap; suitable tubing, and a rubber stopper inserted in the top of the cell. Constant absolute pressure was maintained by means of a manometer connected to the trap with a tee. Flotation: The required amount of activating ion solution was pipetted into a beaker. This was then diluted to 99.0 ml with water having a pH below that desired for the test, or so adjusted with HC1. After addition of 1.0 ml of oleic acid solution (2.0 mg oleic acid per ml), the pH was readjusted to the desired value with NaOH, and the entire solution transferred to the cell containing 1.5 gm of quartz. After vigorously agitating the cell and its contents for 2 min, the vacuum was applied to the cell and the estimated degree of flotation observed for a 3-min period. Activating ions studied included Ca++, Mg++, Al+++, and Fe+ + + added as chloride solutions. In addition,

Jan 1, 1964

By Clayton M. Rumsey

In 1984, the U.S. Bureau of Mines conducted a mineral survey of a 26,598-acre study area which includes the 23,702-acre Mt. Limbo Wilderness Study Area (NV-020-201). The study area is 65 miles northeast of Reno, NV, and is underlain mainly by Cretaceous granodiorite that comprises the Selenite Range. Tertiary basalt, rhyolite, and sedimentary rock as well as Quaternary alluvium and lake deposits are exposed near the study area boundary. Mines just north of the area in the Hooker mining district produced tungsten ore in the 1940's and 1950?s. Similar deposits are not known in the study area. Disseminated gold is in sinter about 6 miles west of the study area and at several other locations regionally.

Jan 1, 1986

By S. H. Penn

Preliminary experimental evidence seems to preclude the use of unlubricated mechanical force drills on the moon. Measured values of the coefficients of friction and adhesion between metallic and nonmetal-lic solids have been shown to increase in an ultra-high vacuum environment. The paucity of real knowledge of the influence of a hard lunar vacuum upon interacting solid surfaces, relegates current proposals to sample the moon with a mechanical force drill, to the equivalent of wildcatting on earth. Within a few years, drilling will be attempted on the lunar surface with tools that have been designed with parameters that are normally considered for most conventional terrestrial drills. Lunar drills must be light in weight, portable, have reasonable penetration rates, low manpower requirements, etc. Although the initial equipment cost is expected to be high, this will probably not be a critical factor. Early lunar drilling will be limited to shallow holes with depths of 10 ft or less. The primary function of these holes will be to furnish samples of lunar surface materials but they may also be utilized for other purposes, such as geophysical experiments. Instruments may be installed in them capable of measuring thermal diffusivity, gamma radiation, etc. As sampling will be the primary objective of the earliest holes, sample contamination is a parameter that effectively excludes such otherwise promising techniques as explosive or plasma jet drilling. The most desirable method is probably some form of mechanical force drilling that has the capability of operating in the extreme lunar thermal environment (125° to 37S°K), high vacuum (10- l3 torr range), and low gravity.

Jan 1, 1968

By Vilkul Yuri

Operation of the iron ore deposits of Krivbass which has been going for 130 years, has led to serious problems related to reaching great depths in open pit and underground mining. Extraction of the huge volume of rock mass (about 9 billion m3) resulted in mass violations of the natural state of the subsurface. At present most mining operations are carried out either by combined open pit and underground mining or by open pits in areas underworked by underground mining. Now the process of movement of the strata underworked by underground mines is not completed ? work fronts of open pits approach the areas of possible funnel, terrace and fissure formation, movement continue to develop. With deepening mining operations the remaining reserves are worked off under layers of incumbent rocks of > 900 m. Significant underground voids arise from mining "blind" deposits at large depths. Heaving of voids over the mined area lasts for decades; it may result in not only unpredictable time of funnel emerging and area development of movement synclines, but also the threat of air blows in mines. Forced caving of incumbent rocks as a way of controllable backfilling is difficult to achieve for economic and technical reasons. This is much more expensive and dangerous than stoping. Furthermore, the mining practice does not know examples of enormous volume backfilling under a km thick rock layer. Currently, RMI "KNU" is conducting research and pre-design work directed at creating a specialized pilot Geoinformation System (GIS) of continuous remote monitoring of rock mass in areas of underground voids influence in Krivbass area. Implementation of this system will enable to determine promptly in time and space the areas of the beyond cut off stress condition, to inform about possible occurrence of events that may result in accidents and to improve safety of mining along with other systems of forecasting and controlling the stress condition in rock mass. RMI "KNU", with a large number of professionals from many Ukraine?s leading mining research centers, has developed a research and design work program that includes the following principal stages: 1. Analyzing geomechanical conditions of combined mining of magnetite quartzite and rich ore deposits; determining mechanisms of moving of rock strata underworked by underground mining and places of hazardous area monitoring. 2. Investigating anthropogenic factor influence on the safe state level of rock strata underworked by underground mining (laboratory studies). 3. Developing processing techniques for continuous remote monitoring of rock mass in areas of underground cavity influence. 4. Modeling the state of rock mass based on results of pilot GIS hardware measurements. 5. Developing an expert diagnostics system for rock mass state in areas underground void influence. 6. Experimental investigation and testing the GIS, its improving for efficient application. After testing the pilot GIS it is supposed to be implemented at all mining enterprises as an integral part of iron ore mining and processing technology in the Krivbass area.

Aug 1, 2013

By Mahmoud Sepehrmanesh, Verya Nasri

The purpose of this paper is to outline the advantages and disadvantages of single tube and twin tubes for subway systems. Different aspects such as diameter of the tunnel (tunnel spaceproofing), configuration of subway line and stations, impacts on passenger safety and evacuation, ventilation system as well as rail system for each solution were evaluated and compared. In addition, a multi-criterion approach is established to facilitate the decision making for these two different subway systems. The practical example of a mega project has been discussed and the details of the decision-making process has been explained. This proposed multicriterion can be used to facilitate selecting the best subway system in any urban areas.

Dec 1, 2022

By James F. Kemp

In submitting an additional contribution to the discussion on ore-deposits in the recent volumes of the Transactions, it is my desire to adhere closely to matters of material importance as affecting the actual processes. Judging from the discussion by Professor Van Hise, and from one or two reviews or other articles by associates of his in geological work, the impression seems to prevail that, in so far as my paper* referred to his masterly essay, I was guilty of misconceptions regarding both the part attributed by him in it to the igneous rocks and the ubiquitous presence of the ground-water. I should regret extremely to be wanting in these particulars or to have misunderstood one for whose great services in this and other branches of geology no one has a higher esteem than myself. I have, however, in the most careful way, and with these points in mind, read his essay again, and, taking it as a whole, I cannot gain any different impression of relative magnitudes than the one first received. The importance of the igneous phenomena and the restrictive influence of the processes described by " cementation " in their effect upon the ground-water, as set forth in Professor Van Hise's "Discussion" (Trans., xxxi., 292), impress me as being in very marked contrast with the same things in his first essay. If the point seems to anyone of sufficient importance, it can easily be decided by reading the originals. My paper was the result of some years of observation, reading and reflection, and was meant to be an independent contribution, controversial only in some subordinate particulars. In depicting the drama of the deposition of ores, I cannot but feel that Professor Van Hise assigned to the chorus and the scene-shifters some characters which, it seems to me, should

Jan 1, 1903

By K. Sasaki, T. Murakami, S. Akibayashi, Q. Wei

A numerical analysis and an experiment were done on groundwater flow past a bore hole with a cylindrical obstacle at its center. Flow around the obstacle in the bore hole was studied in detail. Two dimensional governing equations to simulate this flow were written for the hydraulic head and seepage velocity in a porous medium and for the vorticity, stream function, and velocity in the bore hole. These equations were non-dimensionalized and solved by using the alternating direction implicit and successive-over-relaxation finite difference methods. Flow visualization experiments and velocity measurements in the bore hole were done with a two dimensional model composed of a porous medium. The numerical analysis procedures were validated by a comparison of numerical and experimental results. Effects of the Reynolds number and obstacle size on flow in the bore hole are clearly shown in the velocity and streamline profiles. The quantitative relation between the seepage velocity in the porous medium and the velocity of flow around the obstacle in the bore hole also were estimated.

Jan 1, 1996

By W. Dresler

Since 1900, smelters have produced in Canada over 10 million tonnes of iron silicate waste slag containing significant quantities of nickel, cobalt and copper. The slag is reduced with aluminum and calcium oxide additions to produce a copper, nickel, and cobalt enriched alloy and an obsidian slag. It was found that the obsidian slag contained very low copper, nickel, and cobalt contents, indeed below 0.06% of each the base metals. These metals have been collected in a type of ferroalloy with up to 1.6% Cu, 2.1% Ni, and 0.7% Co. These alloys can be recycled according to standard procedures in base metal smelters. Surprisingly, the obsidian slag was found to display good cementitious and pozzolanic properties, which is a requirement for cement production. The strength producing properties of the obsidian slag are considered to be exceptional at the 28 day standard test age. In most cases, the obsidian concrete is characterized by significantly greater strengths than control concrete tests and concrete containing fly ash or blast furnace slag. Compressive strength data at 365 days for the obsidian concrete is impressive.

Jan 1, 2003

By Martin S. Maier, H. R. Nelson

THE diffusion of metals plays an important role in many metallurgical processes, 1,2 as, for example, the formation of alloys by the annealing of mixed powders, the homogenization of segregated alloys, and the carburization of steel. Other equally important phenomena, such as recrystallization and creep, are based on the movement of like atoms. Although much is known concerning the effects of diffusion in metals, very little is known concerning the details of the physical processes involved.1,3-5 The data that should give most information concerning the processes involved in diffusion are those on the diffusion of like atoms-self-diffusion. Very little is known concerning the rates of self-diffusion of metals because before the discovery of artificial radio-activity in 1934 there was no means of detecting the movement of the diffusing atoms through the solvent metal except in the elements possessing natural radioactive isotopes-lead, thallium and bismuth. Using the induced radioactivity of the element as an indicator, atoms can now be "tagged" so that the rate of diffusion of the radioactive isotopes of an element (tagged atoms) into the stable isotopes of the same element can be measured. As the radioactive and stable isotopes of an element differ only in nuclear structure, it is quite certain that all isotopes of an element diffuse at the same rate. Two techniques have been used to measure self-diffusion. In one, a thin layer of radioactive metal is deposited on the face of the solvent metal, and the decrease in the surface activity as the radioactive atoms diffuse into the solvent metal is measured. This method has been used to determine the coefficients of self-diffusion of lead6-10 and bismuth10 using natural radioactive isotopes, and of gold11 and copper12 using artificial radioactive isotopes. In the other technique a thin layer of the radioactive metal is deposited on one face of the solvent metal, and after diffusion has occurred the specimen is cut in thin sections to obtain the concentration-penetration curve. This method has been used to determine the coefficients of self-diffusion of gold,13 zinc, 14-16 silver,17 and copper.18 The second method was used for the work described in this paper. MATERIALS The coefficients of self-diffusion were determined in two grades of polycrystalline copper and in single crystals of copper. Commercial OFHC copper was used in the form of disks I in. in diameter by 1/8 in. thick. Samples of high-purity copper described by Phillips and Skinner19 were supplied through the courtesy of the American Smelting and Refining Co. The high-purity copper rod was used without remelting by cross-rolling to a thickness of 0.075 in., from which disks 7/8 in. in diameter were cut. A good grade of bus-bar copper was used to make the single crystals.

Jan 1, 1942

By Wei Li

Carbothermic reduction kinetics of ilmenite concentrates catalyzed by sodium chloride and the microwaveabsorbing characteristics of the resulting reductive products were investigated; the reduction degree of the reaction was deduced to be . Results show that the activation energy is 112.03 kJ/ mol when NaCl is used as catalyst, lowering to 23.11 kJ/mol for the final stage activation energy using sodium silicate as a catalyst. There is a sharp change in the reduction rate constant at temperature ranges of 1,223 K - 1,273 K and 1,373 K - 1,423 K. Microwave-absorbing characteristics of reductive products were measured by the method of microwave cavity perturbation. It was found that microwave-absorbing characteristics of reductive products obtained at temperatures of 850° C, 1,100° C and 1,150° C show sharp changes. Through X-ray diffraction (XRD) characterization, it was found that the formation of Fe occurs at a temperature of 900° C during the reduction process of ilmenite concentrate. The decrease of FeTiO3 content results in the decrease of microwave-absorbing characteristics, while the increase of Fe content gives rise to the increase of microwaveabsorbing characteristics. The decreasing trend is larger than the increasing trend, which is the main reason for the sharp changes in the microwave-absorbing characteristics of reductive products at the temperature range of 850° C to 900° C. When the decreasing trend is smaller than the increasing trend, it becomes the main reason for the sharp changes in microwave-absorbing characteristics of reductive products at the temperature range of 1,100° C to 1,150° C. Kinetics results show that sodium chloride can catalyze the carbothermic reduction of ilmenite, and microwave-absorbing characteristic investigations indicate that microwave heating can be used in the carbothermic reduction of ilmenite.

By Józef Czernecki

The Polish copper concentrates are characterised by low content of sulphur and iron. At KGHM Polska Miedz S.A. two copper production technologies are in use. The shaft furnace process is used at the Legnica Copper Smelter and the Glogów I Copper Smelter. A single-stage direct to blister Outokumpu flash smelting process is used at the- Glogów II Copper Smelter. Melting copper concentrates in the shaft furnaces is carried out in a reducing atmosphere and the product obtained is a matte. Instead, a result of melting copper concentrates by an oxidising flash process blister copper of a quality similar to that of converter copper is obtained. The annual copper production at KGHM Polska Miedz S.A. exceeds 450,000 tons. Another important metal is silver produced from slimes from copper electrolysis (about 1000 t/y). Moreover, such metals as Pb, Ni, Se, As, Au and other precious metals, including Pt and Pd, are recovered from various semiproducts. This paper presents technological flow sheet of the copper production in plants using the shaft furnaces and in another plant in which a single-state flash process is applied. Characteristics of products, methods of their utilisation, main parameters of particular technological operations, and advantages and shortcomings of the solution applied are presented. There are also discussed: the natural environment protection as well as directions of the KGHM Polska Miedz S.A. plants modernisation.

Jan 1, 1999

By M. Van Siclen

THE outstanding fact in connection with dust disease in the United States at present is the growing recognition of its seriousness by state officials and by the more progressive operators of mining, metallurgical and allied industrial plants. The same may perhaps be said of labor in some of its better organized centers, but the average independent non-union workman continues, .as of yore, to suffer the toll of disability and even of death from dust inhalation without realization of the source of his ill-being. Progress in the betterment of the handling of sufferers from dust disease and of the conditions creating dust hazards in mining and allied industries is pursuing a course similar to that of the now widespread campaign against accidents, in which the risk is more obvious, more severe, and was naturally recognized sooner. The coming on of dust disease is generally relatively slow and its immediate effects not infre-quently masked by or attributed to other diseases. Marked exceptions to this general rule have occurred in districts where the dust is particularly pernicious, such as the Rand and Joplin; yet such exceptions, unhappy in themselves, opened the eyes of medical men, and of those in other localities charged with the responsibility for the welfare of industry, to the much more widespread if less spectacular hazard existing from the inhalation of dust in all rock-excavating operations and all industrial operations creating inorganic dust, whether it be crushing and grinding, sand-blast-ing, granite-cutting, or what not. Advancement to date in the United States in prevention and treat-ment has been slow, yet the record shows that quantitative methods for determining the degree of hazard and means for decreasing it were being developed as far back as 25 years ago; and that more rapid progress may be looked for from now on. In 1908, in this country; F. L Hoffman?(1) discussed the mortality from consumption in dusty trades, especially brass foundries; and in 1913 E. R. Hayhurst(2) described the effects of inhalation

Jan 1, 1933

By Herbert Herman, M. E. Fine

THE first decomposition product of a supersaturated aluminum-rich A1-Ag alloy at low tempera- tures is Guinier-Preston zones.'-, The zones are ideal and each consists of a spherical shaped silver-rich cluster about 16 A in diam syrounded by a silver-poor shell approximately 72A in diam.' The composition of the two regions is not known with certainty., After quenching from the solution anneal, these zones form rapidly on aging at temperatures as low as -30°C.5 The rate of zone formation increases with aging temperature; the activation

Jan 1, 1961

By B. H. Kear, H. G. F. Wilsdorf

After a few percent strain, dislocations in disordered Cu3Au are arranged in groups in ulell-defined slip planes, which contrasts with the more or less random distribution of dislocations in the corresponding ordered alloy. Unusually long and straigkt dislocation segments observed in the ordered alloy are interpreted in terms of cross slip of screw dislocations from their slip planes into cube planes. It is proposed that cross slip, and also dislocation reactions of the Lomer type, play an important role in work hardening of the ordered alloy. ACCORDING to to dislocations in the disordered lattice are only partial dislocations in the corresponding super lattice, so that in the super-lattice dislocations must occur as pairs, with each pair connected by a ribbon of antiphase boundary. Recently, striking confirmation of the theory was obtained by Marcinkowski, Brown, and Fisher3j4 in a study of dislocation configurations in thin foils of the Cu3Au alloy by transmission electron microscopy. In the present investigation, the observations made by these workers have largely been confirmed. Moreover, it has been found that dislocations in the plastically deformed ordered alloys are often unusually long and straight. This paper is mainly concerned with these new observations. A tentative explanation is offered in terms of cross slip of dislocations in the ordered alloys. PREPARATION OF SPECIMENS An alloy close to the stoichiometric composition Cu3Au was prepared by melting together high-purity copper and gold (99.995 pct) under vacuum in a graphite mold. The resulting ingot was rolled down and cut into strips 1 1/2 by 1/8 by 0.005 in. in thickness. All strips were annealed at 900°C for 3 hr and cooled to 500'~. A few of the strips were quenched from ~OO'C, while the remainder were slowly cooled in the temperature range 400" to 150°C at intervals of a few degrees every 24 hr to produce a high degree of order. After this annealing treatment the average grain size of the material was about 0.1 mm. Material in different states of order was obtained by reannealing fully ordered material at temperatures below the critical temperature: followed by quenching. The equilibrium degree of order attained at a particular reannealing temperature was obtained from the paper by Keating and warren.' A simple hand-operated tensile jig was used to give the strips the required amounts of plastic strain. Following straining, a number of specimens were cut from each strip by means of an electrolytic cutting device.= Finally, each specimen was thinned electrolytically using the polishing procedure described by Bakish and Robertson,7 and these thin sections were examined in the Philips EM-100B electron microscope operating at 100 kv. EXPERIMENTAL OBSERVATIONS Antiphase boundaries. The average domain size in the ordered alloys was found by direct observation to be about 0.25 p. Also, it was observed that the grown-in configuration of antiphase boundaries was changed little by plastic deformation, at least up to 6 pct strain. Fig. 1 shows an electron micrograph of a thin foil of partially ordered alloy (S - 0.8) after 3 pct strain. The micrograph shows a few dislocation pairs and a somewhat crystallo-graphic network of antiphase boundaries. The normal to this foil was found by diffraction analysis to be approximately 11121, with principal directions in

Jan 1, 1962

By J. C. Haptonstall

Stoping methods at the Homestake Gold Mine through 1978 had been traditional overhand cut-and-fill, shrinkage or square set. High costs, low-productivity and safety concerns prompted the mine to search for and adopt a "bulk mining" technique as a primary stoping method. Blasthole stoping had been successful but it is very development intensive, and was not suitable for the mine's accelerated mining program. Vertical Crater Retreat stoping was selected, and today accounts for over 50% of ore production. Case histories representing both the successes and failures of VCR stoping in the mine are discussed.

Jan 1, 1986

By P. B. Altringer

Searles Lake, CA, contains the largest known domestic tungsten resource. The brines in this near-dry lake bed, located in the Mojave Desert 130 mi northeast of Los Angeles, contain an estimated 135 MMlb of tungsten. However, the low concentration of tungsten (0.080 g/L W03) in the supersaturated brine makes selective tungsten extraction very difficult. Although many brine chemicals are extracted from the lake, tungsten recovery was an elusive goal prior to Bureau of Mines development of an ion-exchange technique. This publication describes the Bureau process. The following subjects are ad-dressed: ? The Searles Lake tungsten resource. ? General problems associated with tungsten recovery. ? Bureau research objectives. ? Synthesis of ion-exchange resins. ? Development of a two-stage ion-exchange tungsten extraction and concentration procedure. ? Product recovery and purification. ? Economic evaluation. Flowsheets for recovering three products (calcium tungstate, sodium tungstate, and tungstic oxide) are presented and evaluated, as well as a summary of the research effort and potential applications.

Jan 1, 1985

By R. M. Damodaran

The flotation performance of Florida phosphate rock was evaluated in terms of the mixing behavior of reagents with particulates during anionic conditioning of phosphate slurries. The various conditioning variables that influence mixing, namely, solids loading, agitation speed and the conditioning time were investigated to determine their effect on reagent coating on the particles. The phosphate recovery was used to monitor the conditioning efficiency. The mixing characteristics of the phosphate feed were evaluated in terms of the ratio of the mixing power P, to the minimum power Pm' required to keep the slurry in suspension. It was found that mixing conditions govern the conditioning time required to obtain high recovery. Reagentization was slower at lower P /P m ratios. At higher P /P m ratios, the flotation recovery was optimized and the agitation speed was found to have no significant effect on it. Optimum mixing conditions were obtained for a 74 wt% slurry at an agitation speed of 450 (47 rad/s) rpm. Under the optimum conditions of mixing, recovery was improved at low collector dosages and short conditioning times.

Jan 1, 1995

By Z. Khan

Iron, in the form of steel and stainless steel, is the most commonly used metal in the world. Plain steels corrode and oxidize easily, while stainless steels exhibit improved corrosion and oxidation resistance. It has been found that rare earth metal (REM) additions, such as cerium and erbium, result in the improvement of the abovementioned properties in iron-containing compounds. Gadolinium is a REM, however, there is very little information available on the influence of gadolinium on the microstructure and mechanical properties of iron-containing compounds. Thus, the purpose of this research project was to determine the influence of gadolinium additions on the microstructure and mechanical properties of mild steel and 316 stainless steel. Ten alloys were produced for the purposes of this research. Five of the alloys had a base composition of mild steel while the remaining five had base composition of 316 stainless steel. The alloys for each of the base composition contained gadolinium additions of 0.1, 0.5, 1.2, and 5 weight per cent. The as-cast and the cold-rolled alloys were analysed. The alloys responded well to the cold-rolling with the exception of the 5 weight per cent gadolinium mild steel and stainless steel alloys. These alloys were extremely brittle and underwent a significant amount of cracking during the cold rolling process. A microstructural analysis of the alloys was conducted using a light optical microscope, while the chemical analysis of the alloys was conducted using energy dispersive x-ray spectroscopy (EDS). The resulting microstructures and EDS analyses revealed that the gadolinium displayed minimal solubility in the ferrite matrix of the mild steel alloys and minimal solubility in the austenite matrix of the stainless steel alloys. Instead the gadolinium formed as an interdendritic secondary phase in both alloys. EDS analysis revealed that the secondary phase in both alloys was gadolinium-rich. Vickers microhardness tests conducted on both alloys revealed that the alloys were composite-like, with a hard, brittle gadolinium-containing compound dispersed throughout a softer, more ductile matrix. The corrosion resistance of the alloys was determined through potentiodynamic anodic polarization tests. Two solutions were used for the corrosion rate tests: a 0.5 weight per cent NaC1 solution and a 0.5 M H2SO4 solution. The results from the mild steel alloys revealed that in both the solutions, the corrosion potentials and the corrosion resistance of the alloys increased with increasing gadolinium concentration up to 1 weight per cent. The corrosion rate test results from the stainless steel alloys revealed that the passivation current density and corrosion resistance of the alloys increased with increasing gadolinium concentration in both solutions. The oxidation resistances of the mild steel and stainless steel alloys were determined through the use of a Netzstch Simultaneous Thermal Analyser. For both the mild steel and the stainless steel alloys, it was found that the oxidation resistance of the alloys increased as the concentration of gadolinium increased when compared to the as-received mild steel and stainless steel samples. This could be due to a strongly adhering gadolinium oxide scale that formed on the surface of the alloys and resulted in the protection of the mild steel and the stainless steel.

Jan 1, 2012

By Al Campoli

The majority of the 100 million roof bolts installed each year in the United States are 5/8 inch deformed rebar fully grouted into a one inch borehole. Commonly referred to as B-Series or No. 5 bar, this system is proven effective and cost efficient in coal mines with average to above average roof conditions. One of the critical variables affecting resin bolt performance is the size of the resin annulus, calculated as the difference between the hole and bolt diameters. The optimum annulus has been proven to be '/4 inch, which provides for effective mixing of the two polyester resin components and incorporation of the plastic film packaging within the cured resin. Glove fingering occurs when the plastic film is forced against the borehole wall potentially interfering with the mechanical interlock of the resin and the rock mass. Glove fingering is not a problem with the optimum '/n inch annulus but has been know to occur with the B-Series 3/8 inch annulus. Laboratory testing correlated the degree of Glove fingering with resin formulation and the bolt head to shaft axes alignment. Glove fingering occurred over 45 % of the grouted length of standard B¬Series bolts. The newly formulated Eclipse B-Series resin when combined with a 1/8 inch offset between the bolt head and shaft axes reduced the glove fingering 70%. The Eclipse system allows the 3/8 inch B-Series annulus to achieve the positive mixing characteristics associated with the / inch optimal annulus systems.

Jan 1, 2002

By Anthony Anable

THE definite trend to stricter specifications with respect to hydraulic concrete has become increasingly manifest in the last six years or so; but it remained for the vast reclamation projects of the Bureau of Recla-mation of the Department of the Interior of the last few years to focus attention on this trend, and to demonstrate how thousands of tons of concrete-making aggregates can be produced continuously and auto-matically with a control of fineness comparable with that obtained with small samples in well equipped private and governmental laboratories. Pioneer work in this direction was done, to be sure, by private com-panies, notably the Kaiser Paving Co. of San Francisco, prior to the present vast public works program. Then in 1931 came the first great aggregates-preparation plant of the Six Companies, Inc. to supply. construction materials for Boulder Dam' in Nevada, and now, in 1936, the aggregates plant of the Mason-Walsh-Atkinson-Kier Co., general con¬tractors on the Grand Coulee dam in Washington. At Boulder dam and to an even greater degree at Grand Coulee dam, sand production is recognized as probably the most important single element affecting the physical characteristics of the concrete. For in the construction of dams accurate grading of the fine aggregate has consider-able bearing on the attainment of a uniform and homogeneous concrete of a high degree of workability and placeability and, at the same time, combining high density and low cement content. Low cement content is of value not only from the standpoint of economy but also because the use of an unnecessarily rich concrete causes certain undesirable characteristics to develop. This paper will relate how at Grand Coulee dam methods that are more advanced than ever before are producing four sizes of gravel and a sand having a fineness modulus of 2.5-3.0. The design capacity is 1000 tons an hour. Significantly, the methods and equipment employed are broadly those that have been used for a generation in metallurgical mills for accurately sizing and grading both precious

Jan 1, 1936