Search Documents

By G. Lodewijks

Today most belt conveyors used for the transportation of bulk solid materials are driven in a centralized way with all drives in one location. The dynamics of these systems has been studied since the early seventies of the previous century and are well understood. Compared to the more conventional belt conveyor system with a centralized drive station positioned at the head and/or tail of the system, a decentralized driven layout with drive stations distributed along the whole length of the belt offers a number of advantages. However, to make a decentralized driven configuration a good alternative to a centralized driven, the system designer will have to balance these benefits with the increased complexity. The full potential of a decentralized driven system can only be realized if the right balance is found between the locally applied drive force and the motion resistances occurring along the system. From previous research it was found that in a multiple driven belt conveyor system the most dominant belt behavior occurs in the belt section between the tensioning device and the first drive station. In this paper different possibilities are analyzed to improve this dominant belt response and optimize the starting behavior. This can be accomplished by changing the predescribed start up profile, starting the drive stations in sequence rather then all at the same time and altering the locations of the drive stations.

Jan 1, 2008

By R. M. Hardgrove

Pulverized coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the dificulties incident to the burning of coal. In a. cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverizeti in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. Process of Burning Cement Clinkers The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output, This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,' in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. Wet vs. Dry Plants The study presented here covers 88 plantsl of which 41 are wet and 47 dry. Of

Jan 1, 1942

By R. M. Hardgrove

Pulverized coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the dificulties incident to the burning of coal. In a. cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverizeti in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. Process of Burning Cement Clinkers The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output, This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,' in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. Wet vs. Dry Plants The study presented here covers 88 plantsl of which 41 are wet and 47 dry. Of

Jan 1, 1942

By S. C. Brown, R. C. G. Oliveira

Surface wettability, or contact angle, dictates a number of multiphase ensemble interactions that influence particulate dispersability and adhesion behavior (e.g., filler compatibility] in addition to a number of other phenomena including biocompatibility and bulk powder segregation. The wettability of particulate surfaces significantly impacts nearly all process industries; however, the available techniques to access this quantity are either relative, or tedious-and are application or industry specific. In this study, key features of existing techniques have been combined to design an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.

Jan 1, 2003

By Robert E. Hershey

1. Estimates of reserves were made for three coal beds in Hamilton County the - Lantana, Sewanee, and Richland. Nine coal beds have been mined at one time or another in the county, but not enough information was available to estimate reserves in any beds other than the three given. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 53 million tons as of January 1, 1954. Of this total 35 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove re-serves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By Joe B. Rosenbaum

Waste solutions from sea water desalination processes are enriched in minerals by a factor of two or three. This suggests that extraction of selected mineral components from the concentrated brine might help pay desalination costs. The possible recovery of gold has received particular mention. Sonstadt, in 1872, reported the gold content of sea water as 65,000 micrograms per cubic meter, or 65,000 parts per trillion. At $35 an ounce, this is equivalent to $0.065 per ton of sea water. Fritz Haber, however, after his abortive venture to restore Post War I Germany to economic health by recovering gold from the sea, concluded the gold content was 4 micrograms per cubic meter. Haber's analysis is equivalent to 0.0004 cent per ton. In the past 10 years, investigators using advanced analytical techniques reported from 4 to 27 micrograms per cubic meter. Our brief experiments to determine a threshhold value for the gold in sea water employed solvent extraction for initial concentration, evaporation of the gold-loaded organic for further concentration, and atomic absorption analysis of the gold in the concentrated organic. Radioactive gold was used as a tracer for monitoring the gold through the concentration and analytical steps. Our method established that sea water contains about 11 parts gold per trillion parts sea water, or 0.001 cent worth per ton. This agrees closely with results of recent studies by other investigators employing ion exchange resins and neutron activation techniques.

Jan 1, 1969

By D. J. Blickwede

WHEN iron is dipped in molten zinc at temperatures in the range 840" to 930°F, the two metals react to form layers of Fe-Zn compounds which adhere to the iron. At the galvanizing tem- perature, the successive layers are:' y (Fe5Zn21), 61 (FeZn;), and 5 (FeZn13), in conformity with the Fe-Zn constitution diagram. There is no quantitative information in the literature on the rates of growth of the individual alloy layers over the temperature range 840° to 930°F. Rather all the past experiments have studied the loss in weight of iron as a function of galvanizing

Jan 1, 1954

By F. Bornman

Ore quality is declining, and the current spirals in mineral sands extraction is deemed inadequate to efficiently extract the valuable minerals. A new spiral was developed, the 117HM with the aim to extract the total heavy minerals in the order of 4.0% - 6.0% and the economic heavy minerals in the range 1.0% - 2.2% from the feed. An important measurable in the gravity concentration of mineral sands is recovery. Recovery measures how effectively the separator has extracted the valuable mineral contained in the input stream. The number of turns on the spiral trough influences the residence time of the feed slurry. A further optimisation followed with the development of the twelve-turn 117HM spiral. Four more turns were added for better recovery. The paper quantifies the effect of residence time on recovery.

Mar 30, 2026

"The content of production reports has its origins in raw measurements taken in harsh production environments. The ensuing measurement/estimation errors always affect reproducibility such that, regardless of the fact that they are balanced through statistical data reconciliation, reported numbers are simply the most probable values of inferred probability distributions. This has important implications for how metal recoveries should be monitored and reported. Indeed, in a context where many process optimisation activities are based on small improvements in recovery, there should be no doubt that inadequate handling of measurement/estimation errors can easily exaggerate or mask actual changes in process performance. However, estimates of the reproducibility of reported metal recoveries are rarely reported to plant management. This situation persists despite the fact that a code compliant metal accounting system must inform management about business risks related to metal accounting. To this extent, this paper focuses on the continuous management of reproducibility level of metal recoveries in compliance with the best practices. Sensitivity analysis of primary and secondary metal accounting models is performed to show the resulting probability distributions for metal recoveries. Some guidelines are given for designing and managing metal accounting systems capable of achieving and sustaining predefined levels for the reproducibility of metal recoveries.INTRODUCTIONEach and every mineral processing plant produces daily, weekly and monthly production reports in which metal balances for payable and penalty elements are presented. While such production reports are usually consulted in offices, underlying raw measurements are taken in harsh production environments where mechanical vibrations, humidity, corrosion and dust, to name a few, disturb measurement procedures. It is thus no surprise that several authors (Francois-Bongarcon & Gy, 2002; Gaylard, Randolph, & Wortley, 2014; Holmes, 2010; Spangenberg & Minnitt, 2014) have reported pervasive issues related to mass/sampling measurements in the context of mineral processing."

Jan 1, 2016

By Michael G. Zabetakis, Aldo L. Furno, Henry E. Perlee

The Bureau of Mines conducted an experimental study with liquid and gaseous hydrogen to determine the hazards associated with the use of liquid hydrogen as an ionizing particle detector in bubble chambers . The glass window , the vacuum chamber , and the vent system were investigated . In addition , a study was made of the detection and ignition of escaping hydrogen and of the available electrical equipment for use in hydrogen atmospheres . Materials such as tempered glass , aluminum , and stainless steel are not penetrated readily by the small fragments formed when fully tempered glass is shattered and propelled by hydrogen at initial pressures up to 100 psig ; long , slender fragments from untempered glass may penetrate thin walls of relatively soft materials such as rubber gaskets and lead . Hydrogen can be vented satisfactorily from a vacuum chamber with a well - designed vent system . However , the rapid leakage of hydrogen into the surrounding air is a serious problem because the available detectors are satisfactory only when the accumulation of hydrogen is slow . Much of the electrical equipment currently available was designed for use in hydrogen- air atmospheres .

Jan 1, 1963

By Howard E. Parkinson, John N. Murphy

The past five years have seen communications techniques and hardware developed by the Bureau of Mines and its contractors increasingly brought into use in U.S. mines. The Bureau philosophy has been to help develop and introduce new hardware that goes as far as possible toward meeting the mining industry's needs. The Bureau programs are also designed to provide continuous fallout of new communications capabilities which are introduced to the mine operators as they occur. As more progress is made in meeting mine communications needs, it is hoped that the mining industry will readily adopt the equipment and techniques that it finds most useful in meeting its individual needs. This paper reports on recent advances achieved in the development of improved mine communications systems. In May 1975 the U.S. Bureau of Mines (USBM) conducted a mine communications technology meeting to provide a brief overview of the USBM communications technology developments in the past 5 yr. This meeting lasted for 1 1/2 days. Therefore, I have elected to narrow this paper to a brief review of recent underground mine communication developments. The following will be discussed: 1) Ultra-high frequency (UHF) radio for fan hole drill operators;

Jan 1, 1978

We are all no doubt aware that with today's high costs it is more important than ever to get the maximum possible return on capital invested in the mining industry. Screening is an important and often costly process in the size classification of industrial minerals and for this reason alone it is essential for both managers and operators to fully understand what type of screening equipment is best suited for a particular application and why. The advent of elastic materials such as rubber and polyurethane have added a new dimension to the process of screening. It is important to understand why the physical properties of these materials can be of benefit in the screening process, and recognise which type of screening applications best take advantage of these orooerties.

Jan 1, 1984

By Wallace W. Roepke

Four bit designs, two conical and two radial, were tested in coal against a 60° conical reference bit to obtain data on orthogonal cutting forces and primary respirable dust generation. One conical and one radial design were modified by the Bureau of Mines for these tests. Results were mixed: One radial bit used substantially lower overall cutting forces and specific energy than the other bits and was the only cutter lower on energy and most forces than the standard 60° bit. How-ever, it generated more specific and total dust than any other bit. The four bits were also tested for incendivity, with a 90° plumb-bob bit as the reference. The frictional ignition tests were designed to simulate both trimming top rock and cutting such rock during advance on-sump. Results of these tests were also mixed. The radial bits were substantially less incendive than the reference bit and caused no ignitions in either top trimming or sump modes. Only the modified mushroom-tipped conical bit caused ignitions. Bits similar to this modified design should not be used on drum-type miners in gassy mine areas; in-stead, the other types of bits tested should be used to reduce ignition potential to a minimum.

Jan 1, 1983

By Tong Gao, Jingyu Qin, Xiangfa Liu, Zengqiang Li, Yaoxian Zhang

"The recycling of aluminum materials is a green industry while Al–Si–Fe is a typical scrap aluminum alloy. The key point of recycling Al–Si–Fe alloys is to separate Al and Fe. A method by introducing Al–Si–Fe alloy into Mg melt has been investigated in this work. A separation layer with gathered Fe–rich and Al–poor Fe3Al0.7Si0.3particleswereobtained at the bottom of the cooled ingot, indicating that ß–Al5FeSi phase evolves to Fe3Al0.7Si0.3,and quantities of Al are released to the upper Mg matrix simultaneously. However, the evolution of Al3Fe by adding binary Al–Fe alloy into Mg melt is different. It is supposed that element Si plays an important role in the phase evolution procedure, thus affects the performance of this method.INTRODUCTIONThe rapid development of aeronautic, automotive and aerospace technologies strongly depends on the consumption of materials while sustainable development is the future direction. Aluminum is a recyclable material and Fe is one of the most common impurities. Fe can be introduced into Al alloys by adding low–purity alloying materials and by using unprotected ferrous crucible, tools, or equipment (Belov, Eskin, & Avxentieva, 2005; Lu& Dahle, 2005).For instance, wear–resistant rings are usually inserted into piston head when producing Al–Si pistons and an infiltration procedure by putting the cast iron rings into Al melt before casting is always essential. As a result, both the re–melting of pistons and the reuse of Al melt for infiltrating rings lead to the enrichment of Fe element, which can be even high to5 wt.%(Viala, Peronnet, Barbeau, Bosselet, & Bouix, 2002).It is widely known that coarse ß–Al5FeSi particles will form in high Fe–contained Al–Si–Fe alloys which is harmful for the mechanical properties. In the past decades, several methods to eliminate the harmful effect of ß–Al5FeSi have been investigated which can be widely referred (Munson, 1967; Lee, Kawamura, Inoue, Cho, & Masumoto, 1997; Suárez–Peña& Asensio–Lozano, 2006; Eidhed, 2008).These methods can be divided into two kinds. One is to aggregate and remove the Fe–rich phase through the methods of centrifugation, gravity filtration or magnetic separation. The other way is modifing the morphology of flake–like ß–Al5FeSi by overheating the melt or adding neutralized elements. However, these traditional methods are rarely used due to respective disadvantages, while the commonly used method in industries is using primary aluminum for dilution. However, only less than 30wt.% of scrap Al can be added into primary Al melt for each melting work while it also results in the decrease of product quality simultaneously(Zhang, Liu, & Liu, 2016)."

Jan 1, 2018

By Bluck R. G

The Murray Basin is known to contain major deposits of heavy mineral sands and intensive exploration for new deposits is being conducted in Victoria, South Australia and New South Wales. The western Basin was well served in the Pliocene and Early Pleistocene by a variety of appropriate sediment sources, and potential coastal traps. Immature, fluvially-sourced sediments forming the Pliocene coastal complex of the Marmon-Jabuk Range in South Australia are part of a marginal marine assemblage containing a suite of economically important heavy minerals that include ihnenite, zircon, rutile and tourmaline. From a consideration of Pliocene palaeogeography and coastal dynamics, specific targets where concentrating processes are likely to have operated are identified in the South Australian portion of the Murray Basin. Such palaeo-environments include the down-drift, littoral zone of discrete foredunes or coastal barriers, the source area for transgressive dune complexes, tombolo facies, and intertidal shoals and sandbanks. Similar coastal processes are recognised for a preserved Early Pleistocene barrier complex.

Jan 1, 1990

By T. W. Wlodek

In this paper the relative merits of shot peening, induction surface hardening, spiral-rolling, and the combination of these surface treatments, are evaluated on the basis of their capacity to increase the fatigue strength of drill steel. The S-N relations for plain car-bon steel (SAE 1080) and Ni-Cr-Mo drill steels in the as-rolled condition were determined previously, using the new Canadian method of testing drill steel introduced at the annual meeting of the Institute in Toronto in 1950 (19). S-N curves have now been determined by this method for these two drill steels in the following conditions: shot-peened and drawn, induction hardened, induction hardened and shot-peened, and spiral-rolled. ( S.R.) . The ratios of the fatigue strengths of these steels after surface treatment, to their fatigue strengths in the as-rolled condition, are compared and the most beneficial treatments are thereby pointed out. The expected range of stresses and their distribution during actual drilling operations are estimated from data available, and the mechanism of failure of drill steel in the as-rolled and surface-treated conditions is analyzed. The magnitude of the surface compression stresses and their effect on ?fatigue strength are discussed.

Jan 1, 1958

By Durucan S

Uncertainty due to spatial and temporal variability of different pollutants found in soil, water and air is an important issue in the modelling of environmental impacts. Recognition of spatial environmental patterns is relatively straightforward to achieve by applying most of the well-known artificial neural networks or adopting a stochastic approach. However, it is the temporal component of the environmental variables that makes modelling of the environmental pollutants particularly complicated and challenging. This paper presents the results of a case study investigating the artificial neural network performance when modelling the spatio-temporal behaviour of environmental pollutants. The test case involved the modelling and prediction of the distribution of water quality indicators along a river from the point of discharge of treated mine effluents. The behaviour of river water quality indicators is rather complex and shows a lot of fluctuations due to a number of hydrochemical, hydrobiological and hydrodynamic factors. Results obtained in this study indicate that artificial neural networks provide a very powerful and robust method for simultaneous modelling of spatio-temporal behaviour of environmental pollutants.

Jan 1, 1995

By Gray N. B, Floyd J. M

To gain further understanding of the operating efficiency of the BHP Slab and Plate Products Division (SPPD) RH vacuum degasser, physical and mathematical model studies of the process have been undertaken. The purpose was to investigate how the various process parameters affect the liquid circulation rate, to visualise the flow patterns, and to identify and eliminate the cause of localised wear in the downleg. In the physical model mixing times were measured using an acid tracer technique. The results were applied to predicting trends in times required to obtain homogenous melt composition under varying conditions. A 2-dimensional mathematical model describing the liquid metal flow has been developed using the PHOENICS fluid-flow package. The physical model results were simulated and incorporated into the mathematical treatment and an improved design for vessel geometry is proposed. The effect of rounding the downleg entrance or installing a baffle between the legs is discussed.

Jan 1, 1987

By D. Shen, J. Cheung

Variable reactance arc control by the SPLC (Smart Predictive Line Controller) has been installed at many different mining sites and steel processing plants around the world. Since its first installation 18 years ago, many advances have been made to both the technology, and to its integration with furnace processes and plant operations. The SPLC has helped to improve electric arc furnace stability by reducing electrode movement while maintaining flat line arc power. Stable furnace operation at higher average power increases productivity. This paper summarizes the progression of electro-technology at Hatch since the 1970s, including fixed and variable reactance, digital electrode regulation, and fast variable speed hydraulics for Soderberg electrode, as demonstrated and benchmarked through projects and lessons learned over the years.

Jan 1, 2015

By C. Chongo, L. Little, Q. Mclennan

Since commissioning in 2005, First Quantum Minerals’ Kansanshi Mine in Zambia has produced over three million tons of copper and 1.8 million ounces of gold from a deposit with highly varied copper mineralization. The processing plant is complex with three independent flotation circuits, gold gravity concentration, atmospheric and high pressure leaching, solvent extraction, and electro-winning. For the first ten years of operating the plant, copper mineralogy was inferred from total copper and acid soluble copper assays, and various misconceptions developed about the mineralogy which impacted operational strategy and project decisions. In 2015, an on-site mineralogy section was set up with an Automated Scanning Electron Microscope, the Zeiss MinScan. This instrument has provided detailed mineralogical data that have debunked some of the mineralogy myths that had developed, highlighting the key underlying issues affecting processing performance. This has enabled the development of projects targeting losses of specific copper minerals in defined size classes, unlocking significant value. This paper describes some of the early misconceptions around mineralogy at Kansanshi processing plant, outlining projects that have benefitted from understanding copper mineral distribution. Learnings from Kansanshi are to be applied at other FQM sites, with a similar mineralogy program being set up at the Cobre Panama project. INTRODUCTION The deposit Kansanshi Mine is located in the North Western Province of Zambia, and it has been the largest copper producer in Africa for over a decade. The deposit occurs within a broad northwest trending antiform that can be traced for 12 km, hosted in a zone of complicated faulting, abundant vein injection, breccia development and down-dropped rock units that lies within Kansanshi’s mining license. The copper mineralization within the deposit is predominantly vein-hosted, although some is strata-bound, occurring in thin bands and veinlets parallel to foliation, and some is disseminated associated with albite-carbonate alteration (Gray, 2015). Supergene enrichment has led to significant variety in the copper mineral speciation. This alteration is complex, and has not followed the text-book principles with a neat layer of supergene mineralization overlying fresh hypogene ore. Rather, the occurrence and extent of oxidation and supergene enrichment is highly irregular throughout the deposit, sometimes occurring at significant depth in localized pockets and along fault lines. Gold mineralization tends to follow the copper within the deposit, but it is dominated by coarse-grained, free-milling native gold. The extent of copper oxidation – measured as the fraction of total copper that assays as acid soluble – is used to classify ore into three main ore types, named Sulphide, Mixed, and Oxide, which are then fed to three different primary crushers for processing in independent circuits.

Jan 1, 2019