Search Documents

By M. O. Makwarela, M. W. Erwee, K. Bisaka

"Energy efficiency in mining and minerals processing forms part of Mintek’s long-term research strategy which includes a specific programme designed at overcoming the challenges faced by the South African pyrometallurgy industry.The electric smelting industry is currently severely constrained by the global economic downturn as well as by the availability and increasing cost of electricity. Efficient utilisation of electricity through energy recovery systems and improved smelting process flowsheets can significantly contribute towards creating sustainable operations.Apart from efficient engineering design and solid process control, smelting of either cold or hot pre-reduced ores has been shown to decrease furnace electricity consumption by more than 40%. Various methods of solid-state reduction tests have been carried out at Mintek in order to select the most appropriate process option in the context of the South African industry. This paper summarises a subset of the results obtained, specifically on pre-reduction tests done on South African chromite and manganese ore pellets.In this set of tests, it was found that the use of an organic binder, together with B2O3 as flux, promotes manganese ore pre-reduction, but retards the pre-reduction of chromite. By pre-reducing the manganese ore feed, significant cost savings can be achieved in subsequent smelting processes and there is potential to minimise manganese losses as a result of fuming, due to possible lower operating temperatures."

Jan 1, 2016

By H. L. Retcofsky

Carbon-13 nuclear magnetic resonance (18CNMR) spectra of nine 2-substituted pyridines, seven 3 -substituted pyridines, and nine 4-substituted pyridines have been obtained and analyzed. Substituents included both electron-releasing groups and electron-with hawing groups. Substituent effects on the magnetic shieldings of the ring carbons, except for those in the 2-positions of 2-substituted pyridines, were found to be quite similar to the effects reported for the monosubstituted benzenes, Thus, at least to a first approximation, the two classes of compounds have similar shielding mechanisms. Shieldings of the carbon atoms in the 5-positions of 2-substituted pyridines and those in the 6-positions of 3-substituted pyridines were found to reflect electron release or withdrawal by substituent groups, The pyridinium cation and the compounds 2,2'-dipyridyl and benzonitrile were also investigated.

Jan 1, 1969

By R. I. C. Manning

The Old Dominion Co, at Globe, Ariz., like the: Phelps Dodge Corporation with which it is closely allied, considers safety a major operating problem. Safety is fostered by this company in consideration of both the humanitarian and economic aspects; the officials, take pride in promoting the welfare of employees, and the management has found that the safest way is the most eco¬nomical and that unless an organization is operated economically it can not continue to exist successfully. In planning and operating any safety, organization, terry things must be taken into consideration because an Enterprise can not be operated solely for safety any more than it can for any other single part of the operations. All work must be planned and executed for the common interest.

Jan 1, 1931

By G. Tairova, M. Murchie, B. Esford, E. Lam

"The objective of this project is to investigate methods to lower the sulphate concentrations in the mill effluent. Currently, the concentration of sulphate in mill effluent is approximately 2 g/L. The high concentration of sulphate ion in the effluent has the potential to become a regulatory issue. The target sulphate concentration in mill effluent for this work was less than 500 mg/L. The pilot studies, using sulphate precipitation, were carried out at the mill. The results of the sulphate precipitation pilot study, using calcium hydroxide and sodium aluminate, indicated that:• The sulphate concentrations in effluent could be reduced to less than 500 mg/L.• The concentrations of most other elements of concern, such as selenium, arsenic, cobalt, nickel and vanadium, were also reduced.INTRODUCTIONHistorically, the concentration of sulphate, SO4 2-, in water has not generally been subject to regulation. However, with the increasing global consumption of water, stricter regulations on sulphate quantity may be imposed. Sulphate is a concern in process waters as it forms scale on process equipment and leads to operational problems. High sulphate concentrations may result in adverse health effects. The taste theshhold for the most sulphate salts in drinking water ranges from 250 to 500 mg/L.A literature search and review to identify methods to reduce sulphate concentration in the mill effluent was carried out. A number of methods were selected and tested in the lab. The experimental results indicated that the precipitation methods, using calcium hydroxide and aluminum compounds, barium compounds, as well as the ion exchange and the membrane methods, were effective for the removal of sulphate to below the required limits. Some other elements, such as vanadium, nickel, cobalt, selenium and molybdenum, were also removed.The process, using calcium hydroxide and aluminum compound for sulphate precipitation, similar to the Cost Effective Sulphate Removal (CESR), also known as “Walhalla” process, described in the Montana Tech report (“Demonstration Of Sulfate Removal” 1999), was selected for further consideration [1]. In the CESR process, the water is treated with lime for precipitation of gypsum, followed by the reaction with a proprietary aluminum compound for removal of a residual sulphate. The final pH adjustment is carried out using carbon dioxide. Results of a preliminary cost estimate indicated that the removal of sulphate using calcium hydroxide and aluminum compound was the preferred method of treatment, considering its low cost, availability of chemicals and minimal changes to the existing plant circuit."

Jan 1, 2012

By D. A. Reynolds, R. G. Travis, James J. Dowd, R. F. Abernethy

"1. Reserve estimates have been made for eight coal beds in Monongalia County, W.Va., but only the Pittsburgh, Sewickley, and Upper Freeport beds are important at this time. The Pittsburgh, Sewickley, Waynesburg, and Upper Freeport beds contain the largest recoverable reserves.2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 3,526 million tons as of January 1, 1954. Of this total, 3,294 mil¬lion tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.3. Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Monongalia County, as determined by this investigation, is 47.9 percent. This percentage is based on the total thickness of coal (less partings three-eighths inch thick or more) in the bed rather than on the thickness of the coal mined. Based on the weighted average percentage of recovery for all beds in Monongalia County, the recoverable reserves are estimated at 1,577 million tons as of January 1, 1954.4. Monongalia County coals of the major producing beds are of high-volatile a bituminous rank.5. The Pittsburgh and Lower Freeport beds in this county yield coal that can be used as metallurgical coal, especially when blended with low-volatile coals. The Lower Freeport coal is coked singly and in beehive ovens, and makes good metallurgical coke.INTRODUCTIONThe investigation to evaluate the reserves of coking coal was planned to cover three phases: (1) Estimation of known measured and indicated recoverable reserves of all coking coal; (2) study of methods of upgrading marginal coals through effective preparation; and (3) study of carbonizing properties of coals and coal blends not now widely used for metallurgical coke making."

Jun 1, 1956

By Thomas W. Turk

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

City Resources Limited selected Vanuatu as a target area for epithermal gold mineralization because of its relatively unexplored character and its location on the southwest Pacific rim. During 1985 a systematic program of reconnaissance prospecting was completed on six islands within the Vanuatu group, using a helicopter and a specially designed exploration support vessel with on-board assay laboratory. Within a period of 4 months, reconnaissance prospecting of all six islands was completed, two previously unknown epithermal gold provinces had been discovered, and six major prospects warranting detailed exploration had been identified. Factors which contributed to the success of the program include (i) a flexible management approach, (ii) the mobility and access provided by the support vessel/helicopter combination, (iii) rapid assay turn-around, and (iv) adherence to basic prospecting techniques. The relative merits of various sampling media are discussed.

Jan 1, 1987

By E. Keller

Some years ago the writer's attention was called to the fact that rolling-mill scales from auriferous copper do not have the gold content proportional to the gold contained in the copper from which they are derived.' So, later, he made a few simple experiments, which are described herewith. In order to test the gold movement on the changing surface of a copper plate under the influence of oxidation, plates 6 in. by 8 in. by 1 in. (15.2 cm. by 20.3 cm. by 2.5 cm.) of converter copper, refined, of 99.29 per cent. purity, and leaded copper with a content of 95.65 per cent, copper, were obtained. Ten cuts were made through the thickness of the plates along the longitudinal center and the silver and gold content ascertained in each of the 10 samples in both plates, as shown in the accompanying illustration. The assay results, recorded in Tables 1 and 2, show that the gold distribution is relatively uniform in both plates, while silver has greater variations, especially in the leaded plate. The plates subjected to oxidation were placed in a red-hot muffle for about 2 hr., two small scarifiers being used as supports. Arranged alongside each other, they nearly filled the width of the muffle, and so were practically under equal conditions of heat and draft. The accurate observance of the time was not possible, however, because of other work, but the time of the exposure of each plate in a pair was identical. At the end of each period, each plate was plunged into water and completely freed of scale, which was carefully collected, dried, weighed, and analyzed. Samples of the plates had also been taken of the molten metal and duly analyzed. Table 3 contains the analytical data for the two plates and their several sheets, or layers, of oxide scales. These figures show that in the oxidations of the converter copper the silver is fairly uniform, while the gold is highly irregular and especially low in the first layer. In the oxidations of the leaded copper plate, the silver and gold contents are variable; however, this irregularity is due to two different causes. The

Jan 1, 1919

New Products Equipment

Jan 4, 1953

By Donald J. Worth

INTRODUCTION Minera Real de Angeles makes a very interesting case study in more ways than one. To begin with, it represents the first time a bulk silver deposit has been put into production in Mexico. Second, the feasibility and financing stage spanned a period when the silver price ranged from $4 to $40 per ounce. Third, there was a major devaluation of the peso and a financial crisis in Mexico at completion of the project. Fourth, the composition of the partnership (a major Canadian mining company, a major Mexican mining company and the host government's own mining entity) is worthy of note. This paper gives considerable background on the project and how it came to fruition. The political risk aspects and how the major provider of funds perceived Mexican risk at the time of decision to participate and afterwards are highlighted. LOCATION AND HISTORY The Real de Angeles deposit is located at an elevation of 2300 meters in Central Mexico in the State of Zacatecas (Figure 1). The closest village is Noria de Angeles, three kilometers to the north. The closest cities are Aguascalientes, Zacatecas and San Luis Potosi. The first-mentioned is one hour to the southwest by automobile over good roads. Exploitation of the vein outcrops probably began towards the end of the sixteenth century by the Spanish. Evidence of past mining activity is shown by numerous shafts, manways, dumps and ruins. Also, there were remnants of two rudimentary concentrating mills now obliterated by pit development and in the nearby town of Noria de Angeles the ruins of a small smelter still exist. Compania Minera Gamma, an affiliate of a major international mining company, investigated Real de Angeles from 1969 to 1971. Its evaluation program included 20 drill holes and comprehensive geological engineering and metallurgical studies. The results were not encouraging and the option on the property was dropped. In late August 1973 geologists representing Placer Mexicana which was later renamed Explomin were advised of the availability of the property and liked the prospects sufficiently to make an option payment soon due and to agree to outright purchase by year-end. A series of 34 holes were drilled by Explomin and a preliminary study indicated that the prospect had mine-making potential if the silver price was right. [ ] DESCRIPTION OF THE PROJECT Real de Angeles is best described as a large, low grade open pit silver mine because at today's prices approximately 70% of the realizable revenue is derived from that metal. One must also keep in mind that the operation produces two concentrates - a lead concentrate with high silver content and

Jan 1, 1985

By J. D. Livingston, H. E. Cline

Cu-Pb alloys in the vicinity of the monotectic composition have been directionally solidified under a high temperature gradient at rates up to 2 X l0-' cm per sec. Over a wide range of compositions, high growth rates yield a composite structure consisting of continuous rods of lead in a copper matrix. This range of compositions increases with increasing growth rate, in agreement with arguments based on the relative velocities of composite growth and the growth of copper dendrites or lead drops. The breakdown of the composite structure at slow growth rates is explained in terms of the relative interphase surface energies. The observed interrod spacings of the composite structure are large compared with the predictions of the Jackson-Hunt equations of eutectic growth. ThE directional solidification of many eutectic alloys produces fine composite structures of parallel lamellae or rods. There has been considerable interest not only in the fundamentals of this two-phase solidification process,'-3 but also in the interesting physical properties produced by such regular and aniso-tropic microstructures. Composite structures can be grown only over a limited range of composition, beyond which coarse primary dendrites of one phase appear. In organic eutec-tics, this composition range of composite structures has been shown to increase with increasing growth rate.7"10 These results were explained in terms of the relative velocities of composite (coupled) growth and dendritic growth. Although similar arguments should apply to metallic eutectics,11-13 suitable experimental results are lacking. In contrast to the work on eutectics, the directional solidification of monotectic alloys has received little attention. (The monotectic reaction is similar to the eutectic reaction, except that one of the resulting phases is a liquid, which subsequently solidifies in a separate reaction at a lower temperature.) Directional solidification of some monotectic alloys'4715 yields regular rodlike microstructures, whereas in other cases macroscopic separation of solid and liquid phases occurs.16 chadwick17 rationalized these results in terms of the probable relative magnitudes of the various interphase surface energies. A recent study of chill-cast Cu-Pb alloys18 revealed a fine rodlike microstructure in alloys near the monotectic composition. It was decided to investigate the directional solidification of such alloys, and to determine the range of composition and growth conditions yielding composite structures. The Cu-Pb system is convenient for such a study, both because it is simple metallurgically, with no compound formation and negligible solid solubilities, and because its basic properties are well-documented. Recent literature on the Cu-Pb system includes studies of bulk thermo-dynamic properties,'g surface energies,20"21 densi-ties,25 and diffusion constants.a6 A similar study of the directional solidification of Cu-Pb alloys was recently undertaken, independently, by Kamio and Oya." EXPERIMENTAL Alloys were prepared by melting 99.999 pct Cu and 99.999 pct Pb in a graphite crucible, stirring well, and pouring into a cold graphite mold. Rods 0.175 in. in diam were machined from the ingots. Alloy compositions studied ranged from 25 to 55 wt pct Pb. Samples were placed in graphite crucibles 5 in. long with 4 in. OD and 0.035-in. walls. They were melted under flowing argon in a vertical, two-zone. platinum -wound furnace. A voltage stabilizer was used to minimize fluctuations in input power. The narrow specimen diameter minimized convection. Directional solidification was achieved by driving the crucible downward into a +-in. hole in a water-cooled copper toroid. The toroid was located immediately below the narrow end zone of the furnace. The end zone was separately powered to maintain high local temperature. Therefore a high temperature gradient (approximately 300 deg per cm) was maintained in the specimen throughout the run. The crucible motion was screw-driven. and a wide range of drive speeds were available. The limited rate of heat removal caused a thermal lag in the specimens at high drive rates. However. temperature-time curves from thermocouples imbedded in a representative sample indicated that the average growth rate still approximately equaled the drive rate. Although the specimens were initially homogeneous, melting and re solidification redistributed the lead. producing composition variations of several percent along the specimen length. (During melting. lead melted first and ran down the sample surface. Rapid freezing tended to reproduce the resulting composition gr~dient, but slow freezing did not because a slow-moving interface tended to reject lead. as discussed later.) To determine local composition. ;-g samples were cut from regions exhibiting various microstructures and were chemically analyzed for lead content. Micrographs were taken on as-polished or lightly etched surfaces. Three-dimensional structure of the lead network was viewed with a scanning electron microscope after removal of some of the copper matrix with nitric acid. RESULTS Several different microstructures are observed, depending on composition and drive rate. Because melting and resolidification produced composition gradients, results are best presented in t&ms of final local composition, rather than initial or average composition. The ranges of local compositions and drive

Jan 1, 1970

By C. Lorimer Colburn, Spencer P. Howell

"Numerous accidents are still being reported that have resulted from the delayed explosions in drill holes. Some of these accidents have boon due to retarded burning of the fuse, causing the charge to explode after the miners had returned to the face, but the majority have been caused by the minors drilling or picking into unexploded explosives, either in unexploded bolas or in broken rock. Although the industry has been cautioned by the Bureau of Mines, manufacturers of explosives, and other agencies regarding the care that is necessary in the handling of explosives, yet reports of these accidents are still being received and many of the accidents are fatal, They occur in spite of the best efforts of the mine officials and men, but many of those that have been reported could have been avoided if the following precautions had been observed:Misfires should not be approached even for the purpose of inspection until three hours have elapsed if fuse was used, and ten minutes if electric detonators or electric igniters were used. These are minimum recommendations. It would be preferable to allow a longer time, for fuses have been known to hang fire for twelve hours."

Aug 1, 1920

By J. H. O’Dette

BLISTER formation on wrought aluminum products has been a matter of concern to aluminum fabricators for many years. The fact that blisters make their appearance during the final stages of fabrication means that much time and effort have been expended before it is evident that the material must be scrapped. This and the loss of production are ample reasons for embarking on a research program to find out more about blistering and possible methods of control. Many excellent papers on this subject have appeared in the technical literature in the last few years. In one of the more recent papers, Kostronl gives a fairly complete review of the problem of gas in aluminum and blistering in general. From the work of the various investigators, a general mechanism for the formation of blisters has evolved and may be summarized briefly as follows: Hydrogen gas is usually present in the cast ingot, in the atomic or ionic state, in excess of the solid solubility. At room temperature the gas atoms are relatively immobile, but at elevated temperatures they become mobile and diffuse to free surfaces where they associate to form molecules. If these free surfaces are discontinuities within the ingot then the associated gas molecules collect and build up considerable pressure until equilibrium is reached with the dissolved gas around the discontinuity. Since the solubility of the gas is proportional to the square root of the partial pressure it is evident that large pressures may be built up at the discontinuities. When the metal is rolled to sheet the pressure of the gas in these, discontinuities is sufficient to deform the surface of the sheet and form a blister, particularly when the strength of the material is reduced during the annealing. Although the mechanism of the formation of blisters was fairly well known, the actual impor- tance of the individual roles played by the gas and the discontinuities was not so well established that positive methods for control of blistering were at hand. It was the object of the investigation to learn more about the nature of the discontinuities giving rise to blistering and to develop methods of control. The investigation was carried out in three stages as follows: a) A study of the more commonly used methods of removing hydrogen from aluminum, such as fluxing and holding, and their effects on blistering. b) Location of the discontinuities giving rise to blistering. c) A study, by indirect methods, of the movement of gas in the metal and its effect on blistering, and the development of methods of blister control during fabrication. Removing Gas and Reducing Blistering by Fluxing or Holding-—The work of removing gas and reducing blistering by fluxing or holding was carried out on metal of Alcan 2s (1100) composition with an artificially high gas content. The high gas content was obtained by introducing water into the melt prior to casting; the water reacted with the aluminum forming A12O3 and hydrogen. The procedure was to raise the gas content by introducing water into an aluminum melt and using half the melt to cast one ingot immediately. The remaining metal was treated again with water to make up for the reduction in gas content during holding, while the first ingot was being cast, and then given a fluxing or holding treatment and cast into an ingot. Samples for gas determination were cast from the molten metal before and after the gassing operation; before, after, and during fluxing, and while casting. Samples were also cut from sections of the ingots. Gas determinations were made on these samples using the well known vacuum fusion technique. All ingots were hot rolled at 500°C to 0.250-in. slab which, in turn, was cold rolled to 0.040 in. sheet. The sheet was coiled and annealed for 2 hr at 500 °C and then cut into 5-in. squares which were inspected for

Jan 1, 1958

In 1991, the USBM (U. S. Bureau of Mines) evaluated the mineral resources of the 174,550-acre Bear Creek-Poker Peak area. Located 40 air miles east from Idaho Falls, ID, the study area is in the Caribou National Forest but is mostly administered by Targhee National Forest. USBM personnel mapped and sampled mines, prospects, and mineralized sites in and near the study area. Five types of mineral occurrences were identified in the study area: phosphate, limestone and travertine, placer gold, coal and uranium (the latter contained in the coal), and oil and gas. The study area has a high potential for oil and gas; evaluation of these commodities were beyond the scope of this study.

Jan 1, 1992

"Chairman: Professor H. S. SICHEL Rapporteur: Miss M. I. WATSONPapers:Unrolling of Copperbelt orebodies by J. H. E. Perry and V. H. WiikAn exploration model for tabular orebodies by G. S. Koch and R. F. LinkHarmonic analysis of copper and gold occurrences in the Arbitibi area of the Canadian Shield by F. P. Agterberg and A. G. FabbriMathematical models of orebodies by M. J. Newton and A. G. Royle Estimation of lateritic-type orebodies by A. JournelIn his presentation Mr Wiik said that unrolling could be regarded as a reversal of the natural process of folding, so that the aim of an unrolling procedure would be the reconstruction of original pre-tectonic conditions. While simply formulated, this aim might not always be achieved. The geometrical relationship between points on the deformed surface and corresponding points on the original surface is process-dependent, and a true reconstruction could be achieved only if the deformation history were known in detail.In this computer unrolling procedure all these complexities were ignored. Referring to one particular marker horizon, Mr Wiik said that it was assumed in the procedure that this marker was deposited as a horizontal stratum and that it had subsequently been deformed by simple flexure-type folding.The procedure allowed the geologist to incorporate his knowledge and conception of the deposit through repeated re-contouring with dummy points. This 'manumatic' aspect of the procedure had proved invaluable, not only in resolving specific unrolling problems but also in making the system more acceptable to the geologists in general.Unrolling served towards removing what might be termed `tectonic noise' superimposed on the primary distribution patterns for regionalized variables such as metal content and orebody thickness. From this point of view, variograms derived on the basis of unrolled-plan co-ordinates should be more meaningful in terms of depositional environment than are variograms calculated from a normal map projection.Mr M. M. Oosterveld remarked that it appeared from the paper that there were problems in applying the unrolling technique to ore reserve calculation, and asked whether there were not other methods that might be used for that purpose.Mr Wiik replied that at present unrolling played only a minor role in practical ore reserve estimation within Roan Consolidated Mines, Limited. The techniques currently in use differed from one orebody to another, but in general they involved projection onto a vertical longitudinal section or a horizontal plan, with subsequent grid interpolation by means of a standard computer contouring package."

Jan 1, 2014

By T. F. Witherbee

IN a paper read at the Lake Superior meeting, August, 1880, an account was given of the successful use of Rendrock and Monaky powder upon a scaffoldn and salamander in the furnace. On April 5th, 1881, the same trouble called for like treatment, which, though not so immediately. successful, was on the whole more instructive than the first trial, and points, I trust, to a reasonably sure remedy for all such difficulties. Up to December 4th, 1880, foundry and mill iron were made from Old Bed and New Bed magnetite, and Kearneyy red hematite, when a return was made to Bessemer iron, from an inferior quality of New Bed ore as compared with that used during first blast. January 18th, 1881, New Bed, Chateangay, and East-shaft, a newly-opened Bessemer deposit of Messrs. Witherbee, Sherman & Co., were first used, and continued up to February 13th, on a fuel charge of 80 per cent. anthracite and 20 per cent. coke, the product on the three ores being about 10 tons more per day than on New Bed alone. From this time until March 11th all coal was used, and New Bed, Chateangay, and East-shaft ores, up to February 22d, and from that date Chateangay and New Bed, the product falling off 9 6/10 tons per day as a result of not using coke. It is fair, however, to state that the furnace was not in good condition during' this period, being over-burdened, and the New Bed ore was, temporarily, uncommonly poor, for reasons of no particular interest here.. It required to properly flux it at least 140 per cent. of limestone; and 101 per cent was actually used. March 11th, all Chateangay ore and 80

Jan 1, 1882

By P. J. Uggowitzer, H. Kaufmann

"New Rheocasting is a novel route of semi-solid casting, in which the globular semi-solid precursor material is produced by controlled cooling of only slightly superheated melts in conventional steel crucibles. The resulting semi-solid slugs are placed into the sleeve of a vertical Squeeze Casting Machine and then filled into steel dies. Solidification occurs under hydraulic pressures up to 100 MPa Due to the reduced cost of precursor material, reduced investment cost and easier recycling, the New Rheocasting process offers cost reductions of up to 25% over conventional semi-solid casting · routes. The New Rheocast products are pore free, pressure tight, weldable and heat treatable castings.In the present work the New Rheocasting Process is introduced and the influence of heat treatment on mechanical properties of the New Rheocast alloy A356 is discussed.The alloy A356 is cast under ideal New Rheocasting conditions into a step die on an UBE HVSC 350 Squeeze Casting machine. As-east, TS and T6 heat treatment conditions with variations in solutionizing and aging time/temperature parameters are applied and the samples are tested by tensile testing. Alternatively, the same heat treatment conditions are applied to conventional Squeeze Casting parts and compared with New Rheocasting.Questions of potential cost savings due to modified heat treatment conditions are also addressed in this paper."

Jan 1, 2000

By Koppe J. C

This study presents the procedure of mine modelling and reserve evaluation by means of statistics, computer interpolation methods and aerophotography interpretation. All data are from Carbonifera Treviso, Laura Muller City, Santa Catarina State, southernmost Brazil. From 22 bore holes and nine trenches opened in the coal seam outcrops, a data base including level references and thickness of all rock formations was created.Using this information, basic statistic analysis was carried out, showing that there are three different populations (three modal distribution). These populations defined three geological blocks with different characteristics of overburden removal and mining methodology. This mathematical approach for analysing geological data is very important for correct mine planning and complementary prospection.

Jan 1, 1993

By Hanna P

Coal geologists are under pressure to minimise exploration expenditure, maximise interpretation confidence and produce the results often too soon. This pressure continues to increase as companies are forced to evaluate borderline economic deposits which are usually deeper and more hazardous, such as the Togara North and Togara South projects in Central Queensland.

Jan 1, 1998

By M. E. Wadswort, A. S. Peck

Infrared data disclose that phenacite reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. The absorption band characteristic of the antisymmetrical C = 0 oleate structure appears at a spectral wavelength of 1623 cm-'. Chemisorption also results in the displacement of OH- and silicate from the mineral surface. Infrared absorbance at 1623 cm-1 is correlated with float-ability at different pH for -60-mesh phenacite particles. Phenacite, Be2SiO4, is an ore mineral often associated with quartz, microcline, and chrysoberyl in pegmatites and mica schist. Experimental phenacite beneficiating processes have been confined principally to the flotation of low grade ores occur-ing in several mountain ranges of Utah and Nevada. The U.S. Bureau of Mines ' has recently reported on the separation of phenacite from ore deposits of Mount Wheeler, Nev. Infrared techniques were previously applied by the authors to characterize the role of sodium oleate and oleic acid in the flotation of several non-sulfide minerals.23 A parallel study was projected to the flotation of the orthosilicate mineral phenacite with oleic acid. Infrared spectra provided a 'molecular fingerprint' of the mineral surface and permitted identification of the reaction mechanisms. Infrared data were complemented with flotation and chemical tests. EXPERIMENTAL PROCEDURES The experimental procedures used in this investigation, for which data are presented in graphical or spectral form, are described in chronological test order. Phenacite crystals from Mt. Antero, Colo., were obtained from Ward's Co., Monterey, Calif. The crystals were fragmented in a porcelain mortar to -60 mesh and then pretreated with 0.5 molar HC1 for 15 min to remove iron. Then, the mineral particles were washed free of acid with distilled water and dried. Part of the dried material was ground to a fine powder with a Fisher Grinder using an agate mortar and pestle. Next, the powder was placed in a graduated cylinder and mixed with 500 ml of distilled water. The mineral in suspension was decanted from the settled fraction after 5 min, and the colloidal suspension was used for adsorption tests in which a high specific mineral surface area was required for adsorption and infrared analysis. Conditioning was performed in 50 ml glass centrifuge tubes for both infrared and flotation test determinations. Twenty ml of colloidal suspension was used for the infrared adsorption tests. One and a half g of deslimed -60-mesh HCl pretreated phenacite was added to 20 ml of distilled water for flotation conditioning tests. Six mg of oleic acid was used for each infrared adsorption test, and 0.2 mg of oleic acid was used for the flotation conditioning tests. HCl and NaOH were used for pH modification. The pulps were stirred at a speed of about 1500 rpm for 3 min. Then, the solids were separated out and either dried at 50°C or immediately transferred to a float cell. The pH of the residual liquid was determined with a Beckman Zeromatic pH meter. The flotation procedure is described as follows: 1) A 325-1111 glass micro-float cell was filled with distilled water. 2) Conditioned mineral was placed in the cell and the pulp was aerated through the glass fritted bottom at 7 psi pressure. 3) Floated mineral was skimmed from the cell with a glass slide until flotation ceased. (The end point was reached in all tests in less than 2 min.) 4) The flotation products were dried, weighed, and the recovery was calculated. Samples for infrared analysis were made into mulls using either oleic acid or series 13-21 Halocarbon oil obtained from Halocarbon Products Corp., Hacken-sack, N.J. The mulls were placed between two sodium chloride windows. A characteristic phenacite infrared band at 1868 cm-' was used as an internal standard for quantitative determinations in which absorbance at this position was quantified by the baseline-tangent method4 and related to absorbance at 1623 cm-'. The ratio obtained by dividing absorbance at 1623 cm-' by absorbance at 1868 cm-' was defined as an absorbance quotient for use in graphical presentation.

Jan 1, 1968