Search Documents

By Harold Cook

Discussion of the paper of HAROLD EARLE COOK, presented at the New York meeting, February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 375 to 400. ALBERT SAUVEUR, Cambridge, Mass.-I think we must all agree with Lieutenant-Commander Cook when he says that there is a great deal of room for improvement in the annealing of steel castings and that better results would be attained if the annealing were conducted in closer agreement with scientific requirements. Whether even a carefully annealed steel casting can ever be made the equal of a steel forging of good quality is still a debatable question. Nevertheless, we all realize that very greatly improved results can be attained by careful annealing. Lieutenant-Commander Cook refers to some requirements calling for annealing steel castings above the Ac1 point. He is undoubtedly right where he says that this should be the Ac3 point. Take, for example, a steel casting containing, say, 0.35 per cent. of carbon, having a very coarse structure made up of coarsely crystalline ferrite. If this is heated just above the Ac1 point the ferrite remains, of course, just as it was before, while the pearlite is converted into a solid solution, austenite. Upon cooling, all this austenite is again converted into pearlite, or sorbite, while the coarse structure of the ferrite remains unchanged and the annealing has accomplished very little. It is therefore surprising that the requirement of annealing above the Ac1 point should appear, in these specifications.

Jan 5, 1916

By B Chappell

Backfill in the form of mine waste tailings has inherent problems associated with attaining adequate strengths upon placement. Fines are usually removed to ensure adequate drainage, which lowers the cohesive strength of the fill, leaving the fines to be placed in a tailings dam. Electro-drainage and electro-chemical grouting is examined to investigate its effects on densification and shear strength within a silty clay tailing having low permeability and shear strength. Two separate grouting mechanisms are observed for the iron and silica grouts used. Electroosmosis is associated with iron grout that deposits within the tailing matrix under a converging pH gradient, and increases the permeability of the tailing. This process initiates cation exchange and causes cementing of the granular contact points between the clays. Electro-phoresis causes sodium silicate solution to deposit silica grout in the voids of the tailings. The resultant effect of these mechanisms results in an increase in cohesion, leaving the void ratio of the iron grouted tailings as it was but significantly reducing the void ratio of the silica grouted tailings.

Jan 1, 1998

By E. Kozeschnik

A new model is presented for the simulation of the evolution of precipitates in a multi-component multi-particle multi-phase environment The mathematical formulation as well as the physical background of the model are briefly introduced and its capabilities are discussed on the example of a precipitation sequence in a complex steel. Keywords: Modeling, precipitation kinetics, nucleation, growth, coarsening

Jan 1, 2003

By L. C. Glenn

In the preparation of this paper the writer has drawn freely upon the writings of Orton, Munn, Shaw, Mather, Miller, Hoeing, St. Clair, Jillson, and others, as well as upon his own personal knowledge of the fields of both states. It is to be regretted that certain data gathered by him and his assistants last fall are not available for publication. Oil in Tennessee A few wells drilled for brine for salt making in Tennessee between 1820 and 1840 obtained oil, but no definite search was made for oil until just after the close of the Civil War. Active drilling was then begun in Overton and counties southwest of it on the eastern half of the Highland Rim. A number of strikes were made at shallow depths in the basal part of the Mississippian but the wells were soon exhausted and abandoned. Drilling was revived, about 1892, when the Spurrier district in Pickett County was developed and was followed by the Riverton district in the same county in 1896. A pipe line was laid from the Wayne County, Ky., fields and about 60,000 bbl. of oil were run before a very heavy slump in the production, a failure to find an extension of the field, and excessive local taxation caused the removal of the pipe line in 1906. There was then no production in Tennessee until the discovery, in 1915, of oil near Oneida, Scott Co., at about 950 ft. (289 m.) in fissures in the Newman or St. Louis limestone. This field, however, soon failed and was abandoned. In 1916, oil was found at Glen Mary, Scott Co., in the Newman limestone at a depth of 1232 ft. (375 m.) A number of wells have since been drilled there, some of which were dry while others, close by, were produccrs. The largest one yielded, at first, about 340 bbl. per day and produced for several months, when it suddenly went dry. Several of the first wells began at 6 or 8 bbl. per day and are still maintaining that output. Production is from a fissured part of the limestone and varies greatly in accordance with the size and extent of the ramification of the

Jan 1, 1921

By W. R. Finlay, W. R. Jr. Hibbard

The key feature of the lattice coherency theory of precipitation hardening1 is the forced coherence between matrix and precipitate which elastically strains both lattices and is believed to be the major source of strengthening in precipitation hardening. In systems exhibiting age hardening, the atom movements leading to precipitation are not at all extensive and are such as to require the minimum amount of energy to produce the interface; that is, the new lattice forms in such a way as to be as nearly as possible a continuation of the old with a matched, coherent plane at the interface at least during the initiation of the precipitation. The crystallographic sequence whereby regions of the matrix change to the precipitate lattice usually can be resolved into a set of shearing operations.6'6 Conversely, the perhaps novel speculation is made that solution of a second phase is accompanied by shearing movements which are possibly the reverse of the precipitation shearing movements. A basic premise of the investigation reported in this paper is that precipitation and solution shearing movements constitute structural weaknesses which might cooperate with applied stresses to facilitate plastic deformation. Another basic premise of the investigation is that the application of hydrostatic pressure to a precipitation hardening system will significantly alter the degree of disregistry across the matrix-precipitate interface and thereby significantly affect the course of age hardening. Two binary precipitation hardening systems were investigated: rz pct zinc in aluminum which undergoes transformations, both precipitation and solution, by a simple crystallographic mechanism; and 4 pet copper in aluminum which undergoes a complex transformation in precipitating and dissolving a second phase. The effects of the application of uniaxial tensile creep stress during elevated temperature aging of both systems and of hydrostatic pressure during the elevated temperature aging of 12 pct aluminum-zinc were then investigated. Previous Investigations Van Wert in 1935,~ studied the effect of hydrostatic pressure on the room temperature age hardening of a few precipitation hardening systems. The latter were rather unfortunately selected since none is known to exhibit any marked volume change on aging and the majority were complex commercial alloys the precipitation mechanisms of which are not known. Jenkins, Bucknall and Jenkins~n,~ in 1944, applied tensile creep stresses to a complex copper. nickel-silicon alloy at various temperatures. The complexity of the alloy and the industrial objective of the work did not permit an appreciable addition to the theoretical understanding of either deformation or precipitation hardening.

Jan 1, 1949

By P. M. Sullivan

At its College Park Metallurgy Research Center in Maryland, the Bureau of Mines has installed and is operating a 5-ton-per-hour pilot plant for continuous mechanical separation of values contained in raw urban refuse. The entire sys tern was assembled using commercially available equipment. The process relies on multistage processing including shredding, air classification, screening, gravity concentration, and electrostatic separation. Compactor trucks deliver raw refuse collected along typical routes in metropolitan Washington, D.C., to the pilot plant. The loads are separated into concentrates of (1) light-gage iron, (2) massive metals, (3) glass, (4) putrescibles and waste combustibles, (5) paper, and (6) plastics. While some refinements remain to be made in the processing system flow-sheet, the data obtained to date have been highly encouraging, indicating favorable economics for commercial-size plants.

Jan 1, 1973

By Maribel L- Saucedo-Muñoz, Toshiyuki Hashida, Victor M. Lopez-Hirata, Shin-Ichi Komazaki

"Small-punch tests were conducted at 4, 77 and 293 K on three types of austenitic stainless steels JNl, JJl and JK2, which were solution treated, water-quenched and then aged at 923, 973, 1023 and 1073 K for 5 h. Small-punch test energy was employed for the evaluation of the aginginduced embrittlement behavior in these materials. Fracture surface of small punch test specimen for the solution treated steels exhibited a ductile fracture, showing the highest SP test energy values. The presence of intergranular brittle fracture was observed in aged specimens. Smallpunch test energy decreased significantly as the aging process progressed. The highest and lowest decrease in small-punch test energy with aging temperature occurred in JNl and JK2 steels, respectively. The decrease in small-punch test energy showed to examine appropriately the aging-induced embrittlement in these materials. The difference in aging-induced embrittlement behavior for these steels was explained based on the volume fraction of intergranular precipitates in aged samples.IntroductionA high level combination of strength and toughness is required for cryogenic structural materials used in the superconducting magnets of fusion nuclear reactor. This requirement is beyond the capability of conventional austenitic stainless steels [1]. The Japan Atomic Energy Research Institute (JAERI) developed new cryogenic JNl, JJl and JK2 austenitic stainless steels. The structure of superconducting magnets is supposed to be constructed by welding thick plates of this kind of steels. Thus, most of the components are exposed to thermal cycles. The slow cooling may cause microstructure changes in both the base material and weld zone. These changes may also decrease the fracture toughness of these materials at cryogenic temperatures. Therefore, it is important to study the effect of thermal aging on fracture toughness behavior for these steels. Konosu et al. [2] carried out a study of the effect of thermal aging on the mechanical properties for JNl steel using tension and fatigue tests. Kwon et al. [3] evaluated the deterioration in fracture toughness at cryogenic temperatures for the isothermally aged JNl steel by means of the Small-Punch (SP) test. No other reports were found about the cryogenic fracture toughness behavior for this kind of steels. To evaluate the cryogenic fracture behavior, the elastic-plastic Jrc value is a good alternative [4,5]; nevertheless, the standard required specimen size makes it difficult to be used for the fracture toughness evaluation in small zones."

Jan 1, 2011

By H. C. Boynton, Albert Sauveur

In the course of some experiments conducted in the Metallographical Laboratory of Harvard University, some interesting facts were brought to light which appear to be worth recording in advance of a more elaborate and exhaustive paper which the authors hope to present to the Institute in the near future. Fig. 1 shows, under a magnification of 100 diameters, the microstructure of the cross-section of a steel bar 1/2-inch square, containing 0.52 per cent. carbon, heated to 1100 degrees C. and cooled slowly with the furnace. Fig. 2 illustrates the structure of the same steel, heated to the same temperature but cooled more rapidly in the air. Both samples were cut from the same bar and heated side by side in the furnace. When a temperature of 1100 degrees C. had been reached, one sample was taken out of the furnace and allowed to cool in the air, while the other was cooled with the furnace. The only difference, therefore, in the treatment of both samples will be found in their respective rate of cooling. This variation in the rate of cooling resulted, as shown

Jan 1, 1904

By R Lurf, C Weber

In the frame of this paper a holistic dynamic process model approach is presented in order to introduce operational and technical excellence in drilling and blasting. Both on a macro and micro level the single process parts of drilling and blasting are outlined and their interaction is explained. The use of this approach for closing the gap between process planning and process implementation is explained and an example of the value generated is given.

Jan 1, 2007

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009

By R. K. Conrad

The Bureau of Mines conducted corrosion research to determine suitable construction materials for geothermal resource recovery plants. Weight loss, pitting and crevice corrosion, U-bend stress corrosion, and electrochemical polarization measurements were made on selected metals in brine and steam process environments produced from high-enthalpy hypersaline brine from geothermal well Magmamax No. 1 at the Salton Sea Known Geothermal Resources Area, Imperial Valley, Calif. Cadmium (and by extension cadmium coatings) and a 6061-T6 aluminum alloy were unsatisfactory because of high general corrosion rates and, in the case of aluminum, severe pitting Molybdenum and niobium (columbium) were resistant to general corrosion, pitting, and crevice corrosion, Copper alloys corroded at rates that may preclude their use in wellhead brine, The presence of iron accelerated the corrosion of the copper alloys Titanium alloys were resistant to general corrosion and stress corrosion cracking in all of the environments. They exhibited crevice corrosion in some of the brine and steam environments and Ti6A14V pitted in the brine environments. They exhibited passive behavior over a broad range of potentials. Exposure tests were conducted on a high-temperature polyphenylene sulfide thermoplastic (Ryton) in the same environments. A 40-pct-graphite fiber-reinforced Ryton composite deteriorated readily in wellhead brine and failed in all of the brine and steam process environments; Ryton coatings on 316L stainless steel were adherent and performed well.

Jan 1, 1983

By Daniel R. Shawe

Large tabular beryllium deposits in waterlaid rhyolitic tuff at Spor Mountain, Utah, contain the world's largest known resources of beryllium (as bertrandite). The district also has produced fluorspar and uranium. The largest beryllium deposit is about 2.5 miles long, and known deposits contain many million tons of material with at least 0.5 per cent BeO. The beryllium-bearing tuff (Pliocene?) underlies topaz-bearing rhyolite ( Pliocene?) that contains unusually high amounts of beryllium, fluorine, and uranium, and overlies other volcanic rocks (Pliocene? or Micocene?) and marine carbonate and elastic rocks ( Paleozoic). The deposits occur in hydrothermally altered tuff only where it contains abundant carbonate pebbles eroded from the Paleozoic rocks and where the tuff was deposited as thick layers in now-buried paleovalleys. Basin and Range faults, thrust fa ults, and possibly strike-slip faults formed in this part of the Basin and Range province during the late Tertiary, and volcanic rocks were extruded. Beryllium mineralization probably occurred during this episode. Undoubtedly the beryllium deposits are related genetically to the topaz-bearing rhyolite, but the details of their genesis are not certain and probably are complex. Beryllium deposits are close to major faults, and locally the beryllium is concentrated at faults, indicating fault control of mineralization. Some elements in the deposits, such as lithium, however, are evenly distributed in certain Luff beds and perhaps were introduced prior to faulting. Still other elements, such as manganese and lead, were concentrated in the beryllium deposits and subsequently were leached along late fractures, indicating a period of metal redistribution following mineralization.

Jan 1, 1968

By Constance F. Acton

Based on laboratory structure analyses, a pilot plant investigation was undertaken to evaluate a Michigan conglomerate native copper ore. Comminution or sized feed was accomplished using wet, closed circuit autogenous grinding with and without crushing of the recirculating load. Coarse metallics were concentrated in two stages of jigging with fine metallic copper being recovered in a three-stage xanthate flotation circuit. With a feed averaging 2.09 % Cu, copper recovery ranged from 86-93 % Cu with an average grade of 55.5 % Ca. An evaluation of the processing flowsheet is made in terms of pertinent independent, dependent, and external variables and design factors. Rate equations are developed to describe the grinding and flotation circuits separately as well as the entire circuit as a whole. Performance equations for the overall operation and for the unit operation of autogenous grinding alone are developed in terms of suitable capacity, efficiency and energy consumption terms. Thus, the effects of feed rate, recirculating load and flowsheet design can be rationally evaluated. Energy consumption for various conditions in the pilot plant is compared to the laboratory value. Additionally, size and scale up factors are discussed. Recommendations are made for further studies to be undertaken to further quantify the ore characteristics and the nature of the autogenous grinding operation. However, the feasibilty of beneficiation of this type of native copper ore by means of an autogenous grinding/jigging/flotation circuit is clearly established.

Jan 1, 1977

By Ann Bigué

Outline of Presentation 1. Impacts and Benefits Agreements Defined 2. Elements that determine the content of an IBA: ? the nature of the project ? the identity of Aboriginal communities affected by the project ? the legal environment 3. Content of Impacts and Benefits Agreements Impacts and Benefits Agreements Defined Have emerged in response to effects of major mining projects located on or close to Aboriginal lands and close to Aboriginal communities Are negotiated between the mining project proponent and one or more Aboriginal groups May include government May be known under other names

May 1, 2004

By Quispe Mamani, Mayra Casas Azañero

The research is located within Asuncion and Cospan districts, which according to their geological features in contrast with previous studies pointing out Au, Mo and Pb anomalies create an environment of prospective interest. The objective is to use ASTER Satellite Images to identify ore-bearing hydrothermal alteration zones. To do this, processing techniques such as the combination of bands by RGB 943 and 461, band ratio 4/6, 4/5, 5/8 and 2/1 to identify advanced argillic, argillic to phyllic and propylitic alterations. In addition, indices defined by Ninomiya were used as a third technique in order to reinforce the data obtained from the previous techniques. The results in the study area are confirmed by the SAM spectral mapping technique using spectral signatures from the USGS library. Identifying kaolinite, alunite and pyrophyllite, assemblages of the advanced argillic alteration. Concluding in 3 areas of interest with the band ratios, 5 areas with the Ninomiya indexes and 9 areas validated with SAM, which were contrasted in 13 areas of prospective interest with well-marked argillic alteration.

Feb 1, 2025

By J. J. Frawley, W. J. Childs

Experiments were carried out to induce grain refinement during solidification by applying vibrational energy (freq 20 kc) to small specimens of bismuth, tin, and bismuth-tin alloys. The results show that if the intensity of the applied sound -field is not great enough to fragment the growing dendrites of a pure metal, no grain refinement is observed and the pain size of the dynamically nucleated specimens is the same as the grain size of a specimen statically supercooled the same amount. Bismuth specimens did not show any grain refinement; whereas, the tin specimens did show grain refinement. This phenomenon is the result of the difference in growth habit between the bismuth and tin dendrites. The bismuth-tin alloys showed grain refinement and, in addition, the segregation pattern was changed. THE solidification process is a change in phase requiring the nucleation of the solid phase from the liquid and the growth of this solid phase at the expense of the liquid phase. Since many physical properties and also the integrity of a casting are dependent on the solidification process, understanding and controlling this process are very important.' A good example in the controlling of a cast structure using heterogeneous nucleation theory is the reduction of grain size in aluminum castings by nucleation catalysis.2 This mechanism of nucleation catalysis has been explained by Turnbull.3 Another technique for grain refinement, which has received much attention but the mechanism has not been fully understood, is to vibrate the solidifying melt. Vibrations can be applied to the melt either by vibrating the mold directly or by introducing a vibrating rod into the melt.4-13 Three mechanisms have been proposed to explain this phenomenon: 1) The mechanical fragmentation of the original dendrites that grew into the melt. These crystals or fragmented dendrites act as new growth sites. 2) The nucleation of new grains in the liquid by the generation of very high pressure pulses caused by cavitation in the liquid. 3) The remelting of the dendrite arms during the solidification process. This mechanism is operative only in alloy systems and would be enhanced by stirring or mechanical vibration. The purpose of this investigation was to determine the mechanism that will increase the number of grains when mechanical energy is introduced into a solidifying melt. APPARATUS The unit used to generate the ultrasonic vibrations was manufactured by the Redford Co., and is similar to the one used in ultrasonic soldering. Fig. 1 is a sketch of the major components used for generating ultrasonic vibrations. The crystal transducer assembly consisted of four lead zirconate ti-tanate piezoelectric crystals in an aluminum holder. An acoustical horn, which was fabricated from stainless steel, was attached to the holder by a set screw. The resonant frequency of this unit was 20,000 cycles per sec. A Pyrex crucible, 4 in. in diam and 4 in. high, was contained in a hole in the top of the horn. The piezoelectric crystals changed volume when excited by an electric signal, thereby generating a sound signal which passed through the horn. The crucible was coupled to the horn by a liquid silicone oil. The purpose of the couplant was to transmit the soundwaves from the horn to the crucible. Without the couplant, much of the sound energy would be lost. The energy transmitted was sufficient at the resonant frequency used, so that acoustical cavitation always occurred in the molten metal. The presence of acoustical cavitation was detected by the characteristic hissing sound emitted from the liquid. EXPERIMENTAL PROCEDURE The influence of ultrasonic vibration on the grain refinement of bismuth, tin, and bismuth-tin alloys was studied. These metals were chosen because of their low melting temperature and the relative ease with which they can be thermally supercooled. The following procedure was used for obtaining large amounts of supercooling. Pure bismuth (99.999+), which was received in bar form, was mechanically broken into pieces small enough to be accommodated in a 50 ml beaker. About 200 to 300 g of bismuth and a few grams of SnCl2 as a flux were placed in the 50 ml beaker and melted by induction heating. The melt was held for 20 min at

Jan 1, 1970

By Dan Nilsson

INTRODUCTION A company must have an objective, and that usually is to earn money. In some countries an objective can also be to reduce unemployment in an area or to develop nonindustrialized areas. Government-owned companies can also have as an objective that of serving the com¬munity. This discussion is limited to the consideration of normal companies wanting to earn money. Such an objective, however, has to be defined in more detail. It is not satisfactory only to maximize the total annual profit from, for example, a mining project. In comparison with most other branches, the mining in¬dustry is very capital intensive. When starting a new project, the mining company must invest a lot of money in mines, ore treatment plants, etc. It is normally many years before any income is received from the ore. Fig. 14 illustrates the payments for a new mining proj¬ect with an expected lifetime of 10 years. Whether this project is a profitable one depends on a lot of things. If the company has a shortage of money, it can be impossible to finance the project. Even if the company has enough money, the management may think that perhaps the project may not return the money fast enough. Such limitations will not be discussed here. Suppose that the company has internal funds from its own operation or can borrow them. Since the mining company must invest the money in advance, it is not satisfactory only to add all of the costs during the mine's lifetime and compare them with the total income during the lifetime. The company must include the time value of the capital. In this appendix, the basic investment theory neces¬sary to judge the profitability and costs of mining proj¬ects will be discussed. INVESTMENT THEORY Time Value of Money If a private person has a dollar and puts it into a bank, he or she will receive interest. If the interest rate is r%, the value after one year will be $(1 + r), after 2 years $(I + r)2 , etc. The interest rate represents the time value of money. If the same person wants to have $1 in the bank af¬ter one year, he or she has to put $(1 + r)-1 in the bank today. If the person wants $1 after 2 years, it is neces¬sary to put $(1 + r)-2 into the bank today, etc. So one dollar today is worth more than one dollar tomorrow. It is, of course, not correct to compare money at differ¬ent times since each dollar has a different value. It is necessary to transform all payments to the same point in time. That is called the calculation of the capital value of a cash flow, and to do this an interest rate is used. In the same way, the cash flow from a project like that shown in Fig. 14 can be translated to any other point in time. Most common is to translate all payments to the beginning of the mining period. That capital value is often called the present capital value. Interest Rate What interest rate will the company use? A com¬pany, just like an individual, has the basic alternatives of keeping its money in the bank and receiving interest, or borrowing money from a bank and paying an interest rate. The interest rate represents the time value of money for the company. If the company has a shortage of money, or many good potential investment projects, it has to use a higher interest rate than if it has a lot of money available. Most companies also increase their interest rate as a hedge against the risk involved by using money for uncertain investments, because of taxes, etc. Capital Value When the interest rate has been decided, it is possi¬ble to estimate the capital value of a project. Here the discussion will be limited to the estimation of present capital values. Suppose that one wants to know the present capital value of $1 (Fig. 15), which will be received after n years. To transform it n years back in time, one must multiply it by the factor (1 + r)-, where r is the inter¬est rate the company uses. Table 1 gives these factors for different years and interest rates. Example: At the end of year 5 a mining company has to invest $50 million in a new mine. What is the present capital value at the end of year 0? The company uses an interest rate of 15%a.

Jan 1, 1982

By Omar A. Muhtadi, R. Bruce Thorndycraft, David A. Milligan

9.1 INTRODUCTION Precious metals in a leach solution are extracted, concentrated, and purified to complete the process begun in the heap and to produce an end product which will provide an economic payback to the mine developer/operator. Several different processes are required to convert the dissolved precious metals into pure metal bars. This chapter discusses the actual production of metal once it has been recovered from the pregnant leach solutions by the zinc cementation (Merrill -Crowe) or carbon adsorption processes. Metal production is generally taken to mean the production of a fairly pure "dore" bar. This chapter also reiterates some information from Chapter 8 in a slightly different context, since the focus of Chapter 8 was a fairly detailed description of the two actual recovery processes, whereas the focus of this chapter is metal production. The sale of an intermediate precious metal product is possible (as opposed to the production of dore bars at the mine site); however, the value of the precious metals is reduced by the various charges and risks associated with precious metal processing. For this reason, most operators choose to produce the most refined metal possible in order to maximize project economics. Precious metals may be extracted from the leach solution by both conventional and unconventional processes. The conventional processes are activated carbon/electrowinning (ACE) and zinc precipitation (ZIP). The unconventional processes are resin ion exchange, solvent extraction, and direct electrowinning. A typical ACE process has two circulating loops. The first loop adsorbs the cyanide-metal complexes from the dilute leach solution onto the activated carbon. A second, separate solution loop removes the cyanide-metal complexes from the activated carbon into a strong solution, the electrowinning electrolyte. Activated carbon is transferred from one fluid loop to the other. The operating cost of the ACE process is directly proportional to the quantity of carbon stripped and thus to the quantity of precious metal produced. A typical ZIP process contains a single circulating loop. The solution is filtered, deaerated, contacted with zinc, and filtered again. The barren leach solution is then returned to the heap. The zinc sludge recovered in the

Jan 1, 1988

Excessive dust generation from unpaved mine haul roads is a problem common to most surface mining operations. While optimal road wearing course material selection parameters reduce the inherent dust generation potential, they do not totally eliminate fugitive dust. Many different classes of suppression or palliative treatments are available for mine haul roads and this paper initially ascertains basic selection guidelines, using a set of ideal dust palliative product, application and performance parameters based on mine road-user requirements. An evaluation and modelling methodology for truck generated fugitive dust emissions is developed as a basis for the comparative assessment of dust control strategies. For water-based spraying, a watering model was developed to estimate individual mine road watering frequencies for characteristic site parameter combinations during summer and winter operating conditions, for a required level of control or maximum dust defect. This forms the base-case scenario with which to compare the performance of other types of dust palliatives under the same conditions. Finally, a basic palliative economic evaluation model is introduced with the aim of identifying and costing the establishment, application and maintenance rejuvenation activities associated with the use of chemical palliatives. While palliative cost and performance is generally site specific, it is shown that under certain combinations of conditions, the use of dust palliatives has the potential to deliver cost savings when compared to water-based spraying.

Jan 1, 2007

By V. S. Znamensky, R. V. Stewart

This chrysotile asbestos ore body is located near the northern tip of the Province of Quebec, Canada. It is some 1818 km (1130 miles) north of Montreal, 480 km (300 miles) north of the tree line, and is situated within the zone of continuous permafrost. The open pit ore zone is approximately 0.4 km (1% mile) in length, some 61 m (2OO ft) in width and plunges at 25o to 30 o below surface to a vertical depth of at least 610 m (2000 ft). The ore body was originally evaluated by programs of surface mapping, diamond drilling, and bulk sampling. The fiber is semicrude, possesses excellent strength, and good fiber length distribution. GEOLOGICAL SETTING, LOCATION, AND DISCOVERY The chrysotile asbestos mineralization at the Asbestos Hill mine occurs in serpentinized ultrabasic rocks of Precambrian age. These intrusive rocks are found in older volcanic sedimentary rocks known as the Cape Smith-Wakeham Bay belt and are shown in Fig. 1. The rocks comprising this belt overlie older basement rocks composed of granite and granite gneiss. This belt has a width of 32 to 64 km (20 to 40 miles), and trends in a general east- west direction, a distance of about 370 km (230 miles) from Wakeham Bay on the east coast of the Ungava Peninsula to Cape Smith, located on the east side of Hudson Bay. Two sequences of rock have been recognized in this belt. The lower (oldest) rocks are known as the Povungnituk group, and consist principally of massive lavas and sediments. The upper (younger) rocks are known as the Chukotat group, and are composed of pillowed lavas with interbedded sedimentary rocks. Sills of ultrabasic rocks exist in both younger and older rocks, but are more often found in the Povungnituk group. Concentrations of chrysotile asbestos, as well as nickel and copper minerals are found at or near the base of ultrabasic sills, and are most common where a change in dip occurs. The mine is situated about 1818 km (1130 miles) north of Montreal, approximately 1126 km (700 miles) north of the start of continuous permafrost, and about 482 km (300 miles) north of the tree line. The depth of permafrost at the mine site has been calculated to be approximately 549 m (1800 ft). This rich deposit of asbestos was discovered in 1957 during extensive exploration for nickel in the Ungava nickel belt. During that year, traverses conducted by Murray Watts spotted interesting looking ultrabasic rocks, and followup ground examination disclosed rich surface showings of asbestos mineralization near the present open pit. In 1958, a two-man prospecting party returned to the discovery site and a mineral exploration license was granted to Fig. 1. Location map Keewa Quebec Mines Ltd., a wholly owned

Jan 1, 1986