Search Documents

By L. C. Headley

A series of exploratory tests was conducted to determine the effects of steady electric fields on fluid flow and streaming potential in narrow passages and porous media, the effects of steady electric fields on fluid interfaces, and the influence of internal voltages on fluid flow in a porous porcelain sample. Voltages greater than about 5 kilovolts were found to influence liquid droplets emanating from a capillary tube. Solutions of polyethylene oxide and polyacrylamide in water exhibited widely different behavior than that of other liquids tested. Liquid-liquid displacement tests in porous samples to determine the influence of high voltage applied to the displacing liquid on flow rates and recovery gave no significant differences. No consistently measurable effects were noted, either on flow rate or streaming potential, when an electric field was applied transverse to the direction of flow in porous media and in narrow rectangular or cylindrical channels. Experimental values of formation factor and streaming potential for a porous porcelain sample agreed qualitatively with those calculated from electrokinetic theory for ultrafine capillaries. However, the agreement for the electroviscous effect was not good.

Jan 1, 1970

By A. A. Levinson, M. B. Kirkley, J. J. Gurney

"Scientific advances in the past decade have greatly clarified our understanding of certain concepts relating to the age and origin of diamonds. These advances are largely the result of geochemical studies of mineral inclusions in diamonds, made possible by modem analytical techniques which enable the accurate chemical analysis of micro-sized particles of the order of 200 microns in maximum dimension. As a generalization, the inclusions indicate that most diamonds formed from either of two rock types, peridotite and eclogite. Peridotitic diamonds have yielded ages of 3300 million years, whereas eclogitic diamonds areyounger and rangein agefrom approximately 1000to 1600million years. Kimberlite and lamproite, the two rock types usually associated with diamonds, typically are much younger than the diamonds they contain. Thus, it is now dear that kimberlites and lamproites are only the transporting mechanisms which brought diamonds to the surface and are in no way related to the formation of most diamonds. The latest concepts which developed during the past decade regarding the sources of carbon for the crystallization of diamonds from peridotite and eclogite, and the mechanisms of kimberlite and lamproite emplacement, IntroductionThe decade of the 1980s has seen major advances in our understanding of the age, origin and emplacement of diamonds. The information presented herein is applicable to virtually all natural diamonds, excluding diamonds related to meteorite impacts. There is still some question, however, as to the applicability of the new information to industrial grade ""fibrous"" or ""coated"" diamonds, and to microdiamonds (< 1 mm). In addition to drawing upon our own experiences, this review is summarized from a voluminous literature and for those interested in the original sources we recommend the books by Mitchell and Bergman (1991), Ross (1989), Nixon (1987), Mitchell (1986), Glover and Harris (1984) and Dawson (1980), and the review articles by Mitchell (1991), Gurney (1989) and Meyer (1985).are also discussed."

Jan 1, 1992

MONTANA LOCAL SECTION Executive Committee F. M. SMITH, Chairman J. L. BRUCE, Vice-Chairman . D. C. BARD, Secretary, Box 267, Butte, Mont. FREDERICK LAIST W. C. SIDERFIN The semi-annual meeting of the Montana Section was held at the Silver Bow Block, Butte, Mont., on Friday evening, Oct. 8, 1915. An informal, subscription dinner, at $1.50 a plate, was enjoyed inn&apos; the early evening, by 62 members and guests. After dinner a technical session was held, and a paper entitled Preliminary Outline of Paper on Mines in the Boulder Batholith was presented by J. A. Grimes, who is joint author of the paper, with Paul Billingsley. The paper elicited a lively and interesting discussion, in which a score of members took part. After the reading of the paper the rest of the evening was spent socially. D. C. BARD, Secretary.

Jan 12, 1915

By D. R. Mathews

The Bureau of Mines investigated the effects of tungsten and chromium, separately and combined, on improving the mechanical properties and oxidation resistance of vanadium. Binary and ternary vanadium-base alloys were prepared and tested for oxidation resistance and tensile strength. Softening occurred with less than 1 weight-percent of either tungsten or chromium, followed by strengthening with higher alloying contents. Vanadium alloys containing up to 9.8 weight-percent chromium or 14.1 weight-percent tungsten were more resistant to oxidation in air at 600° C than unalloyed vanadium. For the alloys with 12.20 weight-percent chromium or 14.56 weight-percent: tungsten, the maximum concentrations used, the lower yield strengths were about twice that of 38,600 psi for the unalloyed vanadium. Recrystallization temperatures for these alloys were 100 and 150° C higher, respectively. Alloys containing both chromium and tungsten had properties similar to those of the vanadium-tungsten alloys.

Jan 1, 1967

By Anthony Folger, Howard R. Lowe, J. F. Dougherty, E. G. Trostel, Joffre Meyer

The status of the natural gas industry in Alberta, Canada, is described with particular reference to the current extent of natural gas reserves and possibilities for additional development. Certain major fields are discussed as representative of the types of gas accumulations within various broad geographical divisions of the provinces. The estimation of the future performance of a gas reservoir is discussed as the basis for an estimate of the future availability of natural gas from presently known reserves. The future availability of the provincial reserves and the estimated future demand for gas within the province are described. INTRODUCTION This paper is a condensation of a detailed study of the natural gas reserves and the future availability of pipeline gas in the province of Alberta as prepared for Trans-Canada Pipe Lines Limited and presented in public hearings at Edmonton and Calgary before the Petroleum and Natural Gas Conservation Board of the Province of Alberta. The study began in October, 1950, and resulted in the preparation of five volumes of data at the expenditure of more than 20,000 man-hours. This paper is designed to afford a broad picture with detail limited to a type example of both natural ga-accumulation and future availability of gas supply. The province of Alberta has an area of 255.285 square miles which, for sake of comparison. is 8,359 square miles smaller than the state of Texas. Natural gas was first discovered in 1883 at the now abandoned Alderson well located some 20 miles southeast of the town of Princess. The first gas in commercial quantities was found at Medicine Hat in 1890. During the last 68 years. 187 localities have been discovered which are capable of gas production, and 73 per cent of these have been found since 1945. Sixty fields currently are producing gas, including 22 non-associated gas accumulations. Location of the oil and gas fields and prospects in the province of Alberta is shown in Fig. 1, together with a list of the localities of measurable gas, Fig. 1A. The estimated total provincial gas reserve as of Jan. 1, 1952, for the 104 fields estimated, is 11.7 trillion cu ft proved and probable, and for the 187 known areas capable of production is in excess of 16 trillion cu ft on a total proved, probable, and possible basis. Five fields (Pincher Creek, Leduc-Woodbend, Viking-Kinsella, Cessford and Medicine Hat) are estimated to have recoverable reserves of more than one trillion cu ft each. A sixth field, Turner Valley, was initially in this group, but its reserves have been depleted substantially. Twenty-four fields, of which the above mentioned six fields are a part, have estimated gas reserves (including the possible category) in excess of 100 billion cu ft. These 24 fields account for 79 per cent of the total provincial reserves. Comparative systemic analyses reflect that 56 per cant of Alberta&apos;s gas reserves are contained in sediments of Cretaceous age; 30 per cent in sediments of Mississippian age; 10 per cent in sediments of Devonian age; three per cent in sediments of Triassic age; and the remaining one per cent in Jurassic and Permo-Pennsylvanian sediments. It is expected that the relative importance of the Mississippian, Devonian, and Triassic sediments will be increased as exploration progresses. GENERAL GEOLOGY The western Canada basin comprises the sedimentary area between the Canadian Shield and the Rocky Mountain Front Range, the Arctic Ocean, and the International Boundary. The basin has an approximate area of 765,000 square miles and embraces parts of the provinces of Manitoba. Saskatchewan. Alberta, British Columbia and the Northwest Territories. Generalized columnar sections for the Province of Alberta are shown in Fig. 2. Substantially all of Alberta, except its northeast corner, has sedimentary cover. Sediments of all the geologic systems are represented. except those of Silurian age.

Jan 1, 1952

By F. Keller, A. H. Geisler

ALTHOUGH the subject of precipitation from solid solution appears to be one of the more profitable fields in metallurgy for study with the electron microscope, few comprehensive studies have yet been made. Occasionally electron micrographs have been published that illustrated alleged precipitation in various alloys, but frequently the apparent size, shape and distribution of the particles do not fully agree with those expected from theory or from observations of the precipitate when the particles have grown to a size resolvable with the light microscope. The presence of a Widmanstätten pattern for submicroscopic precipitate particles has been demonstrated for only a few aged alloys.1 The initial problem has been the development of suitable techniques for applying the transmission-type instrument to a field that has been inherently associated with reflection-type microscopes. The various techniques have been the subjects of numerous publications, and instead of describing them individually here it will suffice to say that the oxide film method has proved to be the most satisfactory method yet found for studying the microstructure of aluminum alloys with the electron microscope. This method has the definite characteristic advantage that the actual surface layer of the specimen is examined and not a plastic or silica replica. Doubtless suitable methods for forming and removing the oxide film could be developed for alloys of other metals. The purpose of this report is to point out the characteristics of the oxide film method that have been observed during the studies of numerous aged aluminum alloys and to present the results of these studies. PREPARATION OF SPECIMENS The oxide film method for preparing specimens of aluminum alloys for examination in the electron microscope has been described in detail previously.1,2 Briefly, the procedure consists of preparing the metallographic specimen, forming the film by anodic oxidation and removing the film from the prepared surface of the oxidized specimen. The specimen is polished according to the usual procedure for microscopic examination.3 The specimen may then be etched to remove flowed metal but etching to attack the alloy constituents or to leave them in relief as in the replica processes is not necessary. Electrolytic polishing is not generally recommended. Deep-etched specimens are used frequently, however, since they provide information that is not revealed by polished specimens and frequently present the same information more clearly than do the polished specimens. The surface preparation of specimens to be deep-etched is not important, since specimens that have been subjected to the first wet polishing operation are generally used, but frequently the as-rolled surface is suitable. These specimens are then etched using a suitable macroetching reagent.

Jan 1, 1946

By M. Misra, J. Nanor

The precipitation and removal of arsenic from process waters can be accomplished with addition of lanthanum chloride alone or in conjunction with ferric sulfate. The long term stability of these corresponding precipitated compounds is critical from the disposal stand-point. In this paper the characterization of ferric, lanthanum and lanthanum-ferric arsenate compounds formed at room temperature in acidic and alkaline pH is presented. The characterization techniques used included zeta potential, XRD and SEM. Zeta potential measurements of ferric and lanthanum hydroxides in the presence of arsenate indicate that oxyanions of arsenate are chemically adsorbed onto the positively charged surfaces of these hydroxides. In alkaline pH there is desorption of arsenate species from the ferric hydroxide surface, hence the product is thought to be unstable. On the contrary, lanthanum arsenate is stable in alkaline pH. XRD patterns show that the ferric arsenate formed in acidic and alkaline pH is amorphous, whereas lanthanum arsenate and lanthanum-ferric arsenate formed in acidic and alkaline pH are crystalline.

Jan 1, 1999

By Moyes A. J

The Intec Copper Process uses a strong chloride electrolyte at atmospheric pressure and 80 - 85¦C to produce high purity, 99.99 per cent copper granules and elemental sulphur. A recent, exhaustive study by an independent, major Australian corporation has shown the capital cost of an Inter plant to be approximately half that of a copper smelter at the 200 000 tpa capacity level and approximately half the operating and capital cost at the 50 000 tpa level. The Inter process costs were also shown to be greatly superior to the best available leach/SX/electrowin technology. The process utilises a multi-stage counter current leach at 80 - 85¦C with the addition of air at atmospheric pressure to precipitate iron as a goethite type compound, followed by a two-stage purification process separating impurities in metallic- and other forms. Purified cuprous chloride/sodium chloride solution is fed to an electrolytic diaphragm cell where high purity copper granules are produced at current densities of 1000 - 1500 A/m2 withoutthe need for conventional electrode stripping. Power consumption is approximately half that of the cupric route. The product is suitable for the direct powder metallurgical conversion of the granules to products such as wire or strip. All the steps in the &apos;furnace free&apos; conversion of copper mineral to product have been demonstrated The process can treat low grade and contaminated concentrates without penalty, thereby offering greater returns to the miner. Lead, zinc and silver may be recovered as metals, with the high oxidation potential of the electrolyte allowing extraction of gold at high efficiency. The gold is selectively precipitated on activated carbon with negligible copper and silver contamination.

Jan 1, 1992

By D. Mraz

"Under high pressure in a deep potash mine, the salt rock behaves in accordance with the concept of a generalized, perfectly plastic substance. The paper presents the evidence of this behaviour and engineering concepts f or room-and-pillar design. IntroductionThe mining and refining facilities at International Minerals &. Chemical Corporation (Canada) Limited are located near Esterhaz y at the southeastern edge of the Saskatchewan evaporites. Ore extraction began in 1962 and at the present time the annual mining capacity is in excess of eleven million tons of potash ore.A generalized geological section is shown in Figure I. The mining horizon is overlay in by 100 feet of rock salt followed by a thin bed of competent dry shale. The strata in the next 1,500 feet are generally competent and locally water bearing. The Blairmore formation contains strata of water-bearing unconsolidated sand. Below the mining horizon, rock salt is interbedded with anhydrite bands.The 8-foot mining bed is distinguished mainly by grade and clay content, as there is no definite bed boundary. The chief mineral s are halite, sylvite and, in some cases, carnallite, with up to 2 per cent disseminated clay. The ore is coarse grained, with crystals averaging one-half to three-quarters inch across.The major mining problem is related to the fact that the Dawson Bay formation, overlying the evaporites, contains areas and channels that are highly porous and permeable and are filled with unsaturated brine under high pressure. Consequently, all mining areas, with no exception, must be so designed that the overburden salt stratum remain s competently supported for the duration of the mine .This paper outlines a successful engineering method of determining the stability of the pillar s and designing a stable room -and-pillar mining system."

Jan 1, 1980

By R. L. Jones, H. Conrad

The effects of gain size on the room-temperature tensile properties of commercial(A- 70)-purity and iodide-purity titanium were investigated by concurrent tensile testing and thin-foil electron transmission studies. The mechanical tests showed that the effect of grain size on the yield, flow, and fracture stresses could be expressed by relations of the Hall-Petch type. The magnitude of the grain size effect on the yield stress was larger for commercial-purity than for high-purity titanium, but in both materials it was intermediate between that typically observed for fcc and for bcc metals. The effect of strain on the gain size sensitivity of the flow stress was found to reflect the grain size dependence of strain hardening. The electron transmission study indicated that the tensile behavior could be accounted for in terms of the dislocation densities and distributions formed during deformation. It was concluded that the effect of grain size on strength could be attributed to a relationship between grain size and the dislocation densities generated in initiating and sustaining plastic flow, the difference in stress levels being due to strain hardening. The relationships between recrystallized grain size, uniaxial tensile properties, and dislocation substructure have not been explored in any detail for a titanium. With titanium and its alloys finding increasing applications in aerospace systems, such information has become essential. The research described in this paper had two objectives: first, to document the effect of grain size on the yield, flow, and fracture stresses of unalloyed a titanium by the tensile testing of recrystalliied specimens at room temperature; second, to attempt an interpretation of the mechanical test behavior in terms of the dislocation structures formed on deformation, as observed by transmission electron microscopy of thin foils prepared from deformed tensile specimens. The observations reported here are restricted to room-temperature deformation; the effect of temperature on the yield and flow stresses of a titanium and the athermal nature of the contribution of grain size to the flow stress have been discussed elsewhere.1"3 EXPERIMENTAL DETAILS Two purity grades of unalloyed titanium have been investigated: Crucible Steel A-70, a typical commer- cial-purity product, and a high-purity iodide grade supplied by the Foote Mineral Co. Chemical analyses for interstitial impurity contents are given in Table I, together with values for the total interstitial atom fractions in terms of oxygen equivalents, which were calculated by the method outlined previously.4 ,5 According to the manufacturer&apos;s nominal analysis, the A-70 grade also contains about 3700 ppm of Fe. The A-70 grade was supplied as 1/4-in.-diam centerless-ground rod. The iodide grade was supplied as crystal bar which was consolidated to approximately 1/4-in.-diam rod by a single, rapid, molten zone pass, using electron beam heating. The 1/4-in. rods were cold-swaged to 0.078-in.-diam wires and 2-in. lengths were recrystallized in a vacuum of -5 x 10-5 torr, giving grain sizes in the range 0.8 to 30 . The thermal treatments and resulting grain sizes are summarized in Table 11. Since there was in no case any obvious sign of a bimodal dis tribution of grain sizes, the grain size values quoted in Table I1 are those obtained from mean linear intercept measurements involving >I00 grains. For the two coarse grain sizes the measurements were made using conventional optical techniques. It was noted during these determinations that the etchants used (10 pct HF; 30 pct HN03; 60 pct H20 and 2 pct HF; 2 pct H202; 96 pct H20 were both tried) etched grain boundaries very nonuniformly and optical polarization effects had to be employed to reveal boundaries which might otherwise have been missed. It was found that this problem became more acute with the finer grain sizes as the usefulness of polarization diminished.

Jan 1, 1970

By H. J. Beach, W. C. Goins

The laboratory development and field use of oil well cement compositions* with high resistance to drilling mud contamination are described. Resistance is obtained by adding a I-lb mixture composed of three parts paraformaldehyde to two parts sodium chromate tetra-hydrate for each sack of cement. This mixture neutralizes the cement-retarding properties of quebracho and other tannins, starch, sodium carboxymethylcellu-lose, Ignite, and monovalent salts of lignosulfonic acid. The retarding properties of calcium lignosulfonate are unaffected. The decontaminating mixture may be used in common cement (designated Type I by ASTM specifica-tions,&apos; Class A by API Std. 10A2) or in a slow set slurry prepared from common cement by addition of calcium lignosulfonate. No changes in slurry viscosities or thickening times are caused by the protecting reagents. The method has been used in 185 field jobs where an improved success ratio has been obtained in plug setting. INTRODUCTION Field experience and laboratory investigations have established contamination by drilling mud as a major factor in oil well cement failures. During 1955, 12 attempts were required to set six open-hole cement plugs in the Timbalier Bay field, La. Eighteen to 30 hours elapsed between placing and testing the plugs in preparation for sidetracking operations. Considerations of rig time expense required immediate resetting where soft cement was drilled after a reasonable waiting period. Sea water drilling mud was used in each well and daily additions of thinners, usually lignites, had been required. Sodium carboxymethylcellulose had been added regularly to control fluid loss. The 50 per cent plug failures were attributed primarily to contamination by the mud. Similar experiences can be found in other fields along the Texas and Louisiana coasts where drilling muds normally contain large quantities of organic treating materials. Cement contamination was the subject of a survey by the Mid-Continent District Study Committee on Cementing Practices and Testing of Oil-Well Cements of the API.3 Data collected from member laboratories and released in Sept., 1951, reported the effects of a number of drilling mud treating chemicals on cement. The study revealed that many of the additives, notably the organic materials in relatively small quantities, had marked effects on the properties of cements tested. Severe losses in strength and erratic thickening time resulted from small additions of mud treating chemicals such as quebracho, starch, sodium carboxymethylcellulose, and lignite. The report included no recommendations of methods for overcoming the problem. One investigation of the contamination problem reported the successful use of activated charcoal in setting cement plugs after conventional slurries had failed.4,5 The investigation indicated that an optimum concentration of 5 per cent activated charcoal was effective in combating contamination from 16.7 volume per cent of treated mud. Laboratory and field muds were included in tests and contained varied quantities of ode or more of the following: quebracho, caustic, starch, lime, and calcium lignosulfonate. The function of the charcoal appears to be physical, removing the organic materials by adsorption. The method may be employed in API Class A or Class D (unretarded slow set) cements. The chemical approach presented here is based on

Jan 1, 1958

By S. R. Balajee, I. Iwasaki

The interaction between British gum 9084 and dode-cylammonium chloride (DAC) at quartz and hematite surfaces was established from coadsorption studies and streaming potential measurements. The cationic DAC interacts with the somewhat anionic British gum 9084, leading to the formation and adsorption of a binary complex of DAC-British Gum 9084 at the interface. The parallel ability to depress quartz along with hematite as a result of the interaction between DAC and British gum appears to be the main reason for the ineffective depressant action of starches and starch derivatives in the cationic flotation of iron ores. Amines are not particularly selective collectors for the flotation&apos; of siliceous gangue from iron ores and, therefore, a suitable iron oxide depressant is needed for a satisfactory separation. Various starches and their derivatives have been extensively tested with oxidized iron ores,&apos;-3 and it has been empirically established that British gums and dextrins are preferable. However, for the flotation upgrading of magnetite-taconite concentrates from 8 or 8.5% Si O2 to about 5% Si 02, British gums, which have been used so successfully on oxidized iron ores, have been found to have no effect and oftentimes are actually deleterious.4 In previous articles,5-7, starches were shown by adsorption measurements, flotation tests, and floccula-tion tests to interact with calcium ions in solution, and it was thought that a study on the interaction between starches and dodecylammonium ions would be able to shed some light on the anomalous flotation behavior described above. In fact, starches are known to interact markedly with paraffin-chain-type surface active agents and, thereby, to precipitate the starch or inhibit the iodine-starch reaction.8 From X-ray diffraction studies and viscosity measurements, the formation of a helical complex between mylose and a surface active agent has been postulated.9 The interaction with other types of hydrophilic colloids, such as synthetic polymers and proteins, has also been investigated and is usually explained in terms of van der Waals&apos; force interaction and/or ion-ion interaction. In the present investigation, the interaction of British gum and dode cylammonium chloride on quartz and hematite was studied by adsorption and streaming potential measurements in an attempt to establish the mutual adsorption behavior of British gum and dode-cylammonium chloride on mineral surfaces and to clarify the anomalous depressant activity of British gum in the cationic flotation of iron ores. All the measurements were carried out at a natural pH of near 7 because dodecylammonium chloride gives maximum selectivity of flotation separation at this pH2 and to avoid any third parameter in the system. EXPERIMENTAL MATERIALS AND METHODS Minerals: The quartz and hematite samples used for the adsorption tests were prepared as described in a previous paper,"J except that the specific surfaces of the samples were increased to 5,860 and 16,000 Sq cm per gm, respectively. For the streaming potential measurements, the 48165-mesh fractions screened out of the original samples were etched with hydrochloric acid, washed repeatedly with water, and stored under water in Pyrex bottles. Reagents:DodecyIammonium chloride (DAC) was prepared1 1 by bubbling dry hydrogen chloride gas through a benzene solution of high-purity dodecylamine supplied by Armour and Co. British gum 9084, received from Corn Products Co., was solubilized by first dispersing it in water to produce a 0.05% solution and then homogenizing it in a blender for 5 min. Distilled water was used in the preparation of the samples and the solutions and for all test work. Adsorption Measurements: The procedure for the adsorption density determinations was also the same as that described in the previous paper.1° The residual concentrations of the British gum and the DAC in the supernatant solution were analyzed colorimetrically by the phenol-sulf uric-acid and amine-picrate methods, respectively. The validity of the mine-picrate method for the colorimetric analysis of DAC in the presence of British gum and the analysis of British gum in presence of DAC were checked by establishing calibration curves between optical density and concentration. Streaming Potential Measurements: The cell assembly for the streaming potential measurements was similar to that described by Fuerstenau.&apos; The streaming potential

Jan 1, 1970

By G. Alfano

This investigation is concerned with the optimization of ultrafine grinding of solids. It is focused on a dynamic classifier for recovering the fine fraction, for automatic recycling of the oversize particles and for reducing power consumption. Power consumption plays a major role in these energy intensive processes and depends on several parameters such as nature of the solid, degree of fineness of the finished product and, above all, grain size of the feed. This study indicates the optimal conditions for a dynamic classifier, that is, geometric characteristics of the apparatus and its capacity, inlet air flow rate and dimensions of the classification circuit. It is also shown that a mean grain diameter (dm) of about 2.00 µm with top size (dmax) of 50 µm can be achieved with an imperfection value of below 0.40 and energy consumption of 215 kWht-1. Keywords: air classification, dynamic classifier, jet mill, energy

Sep 1, 2012

By Roderick Eggert, Dipesh Dipu

We look at the empirical evidence of coal block auctions in India to understand how competitive intensity affects the bid amounts in common value auctions. The results suggest that competitive intensity measured through the number of bidders for a coal block is instrumental in determining the bidding outcomes. The presence of higher numbers of bidders in the auction leads to higher bids - every additional bidder causes the bid amount to rise by INR 142.67 per tonne of coal for auctions studied for 127 coal blocks from 2014 to 2023. The paper also examines the moderating and mediating effect of competition on bids and on excess of bids from the comparative market price of coal from alternative source of Coal India Limited. The results indicate that competitive intensity does not have statistically significant impact on the relationship between common value of coal blocks and bids, neither as a moderator nor as a mediator. The strategic behavior of the bidders has also been observed as bidders have been seen to bid in a higher than market price in order to outbid the competitors.

Feb 1, 2025

By Gilbert Thiessen

THE purposes of this paper are (1) to show that the mineral matter content of coal is satisfactorily represented by the Parr formula; that is, Mineral matter = 1.08 Ash + 0.55 Total sulfur (2) to compare ash-to-mineral-matter ratios with factors by which ash values must be multiplied in order that dry, factor-times-ash-free values shall equal Parr unit coal values; (3) to examine such ash-correction factors and to compare them with similar factors corresponding to certain simplifications or modifications of the Parr formulas and (4) to show that ash-correction factors used for simplification in calculating approximate unit coal calorific values cannot be. correctly used for the conversion of other determined values in an analysis to the unit coal basis, but that each type of calculation requires separate treatment in simplification.

Jan 1, 1934

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference&apos; reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference&apos; reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By Carla A. Kertis

Because coalbed discontinuities often pose serious economic and safety problems in underground coal mines, criteria were documented for the recognition and prediction of discontinuities in advance of mining. Pennsylvanian strata in Indiana and Armstrong Counties, PA, were deposited as part of fluvio-deltaic complexes with channel-phase sandstones as the predominant type of coalbed discontinuity. Coalbed isopach maps constructed for this study delineated numerous want areas (areas of no coal) with elongate to linear geometries. A comparison of coalbed isopach and corresponding sandstone isolith maps of the study area revealed many examples of a thick-sandstone, thin-subjacent-coalbed relationship. Nearly 60 pct of the want areas in the study area were found to lie subjacent to thick (> 20 ft [6 m]) sandstone accumulations. In addition to erosion of the coalbed, channels may contribute to coalbed splitting, coalbed thinning over paleotopographic highs, abnormal coalbed thick- nesses, and deterioration of coal quality. If these features are considered, then approximately 80 pct of all interruptions in the economic coalbeds in this area result from channel activity. By using the criteria developed in this study and described in this Bureau of Mines report, the occurrence of coalbed discontinuities may be predicted and anticipated in advance of mining.

Jan 1, 1985

By R. H. Dourson, B. H. Sage, W. N. Lacey

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943

By W. N. Lacey, R. H. Dourson, B. H. Sage

The compositions of coexisting phases in the methane-propane-n-pentane system were determined at 160° and -2 20°F. throughout the two-phase region, at pressures above 500 lb. per sq. in. The experimental results permitted the calculation of gas-liquid equilibrium constants as well as the establishment of the critical behavior of this ternary system. Although many binary paraffin hydrocarbon systems have been investigated, the experimental work relating to the phase behavior of ternary paraffin hydrocarbon mixtures at elevated pressures is relatively scarce, being limited to a study of the meth-ane-propane-PL-pentane system at 100°F.l,2 However, Guter and co-workers have studied the phase behavior of the methane-ethane-ethylene system at relatively low temperatures. Information concerning the phase behavior of ternary systems is of value in predicting the behavior of the components in multicomponent systems, since the influence of pressure, temperature, and concentration may be individually ascertained. In the light of the importance of such information, the study of this ternary system was extended to higher temperatures in order to increase the field of temperature in which the data could be applied. Since all states encountered in this investigation are above the critical temperature of methane, the details of its phase behavior are not of direct significance. The properties of propane in the heterogeneous region were taken from a correlation3 based upon recently published data. The corresponding information for n-pentane was taken from experimentally measured vapor pressures and volumetric data.4 The rnethane-propane system has been studied throughout the two-phase region at temperatures above 70°F.,5 while the phase behavior of the propane-n-pentane system has been established for temperatures above 160°F.6 The volumetric and phase behavior of the methane-72-pentane system has been studied in detai1.7,8 The experimental measurements serve to establish with adequate accuracy the phase behavior of the components and of the constituent binary systems for this ternary system. It is believed that, with the exception of the measurements for the methane-propane system, the uncertainties in the earlier data relating to the pure substances and the binary mixtures are probably less than those associated with the values reported here. Method The methods and apparatus employed in this investigation have been described.137 In principle, the method involved the withdrawal of samples of the coexisting gas and liquid phases from a vessel containing a heterogeneous mixture of methane, propane and n-pentane. Provision was made so that

Jan 1, 1943