Search Documents

By L. A. Neumeier

The Bureau of Mines evaluated creep and other properties of extruded Zn-30 pct-AI alloys containing 0 to 0.7 pct Mg. The alloys were extruded both above and below the Zn-Al eutectoid temperature of 275° C. Creep behavior is defined for the alloys as extruded and after various heat treatments. Tensile properties, hardness, thermal expansivity, impact resistance, and microstructures are given. The alloys, either with or without magnesium, required substantially less pressure for extrusion near 275° C than at higher or lower temperatures. The alloys containing magnesium exhibited significantly greater hardness, tensile strength, and creep resistance, but much lower ductility than the 2n-30 pct Al alloy. The properties were very sensitive to the processing conditions.

Jan 1, 1971

By J. R. Woolsey

The cost of an offshore exploration project is mainly dependent on the size of the vessel engaged for the work and increases dramatically with increasing size. Of the various factors influencing vessel size, the type and size of the sampling equipment is typically the principal consideration. This scenario is particularly true of shallow sampling programs employing a vibracore system. The problem develops when certain bottom materials such as densely packed fine sand require sampling. This type of material being one of the most difficult for the standard vibracore systems, with integral core liner, to penetrate to a reasonable depth of some five to seven meters. The problem is mainly related to the excessive cross sectional area of the cutting bit required to accommodate the core liner. The typical solution has been to apply more power to the vibracore drive head which results in a considerable scale-up for the entire system with attendant increase in vessel size. In order to reduce operating cost, M.M.R.I. has developed several systems for deployment from vessels in the 20 meter range. Two systems are modifications to the basic vibracore and a third is a vibralift system. Basically, one of the vibracore units is employed where core liners are required, utilizing a special jet bit designed to reduce the cutting pressure on the bit while not affecting the integrity of the core. The other designed for core extrusion on

Jan 1, 1986

By L. B. Khershberg

According to geochemical specialization, cobalt-manganese crusts (CMC) of the Magellan Seamounts are rich in cobalt and manganese and are complex in composition. Besides cobalt, manganese, and nickel, they contain such components, as platinum, copper, molybdenum, and rare earth elements, which enhance the value of this material. Factors and conditions responsible for Co-Mn ore-genesis and processes of cobalt-manganese crust formation are described in a number of Russian and foreign geological papers. The study of ore-concentrating processes in the Magellan Seamounts helped to solve an important applied problem, namely to reduce the time needed to reveal the factors of CMC formation mechanism. The authors of this research found seawater over the described area of Magellan Seamounts to be stratified and to contain high concentrations of manganese, iron, cobalt, nickel, copper, lead, and zinc. Diagrams of suspended Co, Mn, Ni, and other components in seawater (0-5500 m), as well as medium concentrations of basic elements (Co, Mn, and Ni) in ore deposits of metallogenic levels of Magellan Seamounts, were found to coincide both on guyots and abyssal plains. Detailed geological study of guyots in the Magellan Seamounts (Dalmorgeo, IOAN, Roskomnedra, and others) revealed that medium Co-Mn crusts cover bedrock rocks in narrow ribbon-like bodies along the edges of bathymetric intervals 1300-1600 m, 1400-2000 m, 2000-2500 m, and 2500-3000 m.

Jan 1, 2004

By Thomson I. R R, Friday R. G, Palmer W. T

The paper introduces the problems encountered in designing open stopes and briefly examines the factors that determine the final stope dimensions achieved after mining is completed. A case study is presented where monitoring of a stope was considered necessary due to the expected formation of a highly stressed crown pillar above the stope. The influence, on the mining approach adopted, of a yielding crown pillar is discussed. Monitoring and numerical modelling were used to develop an understanding of the behaviour of the particular stope as mining progressed. A comparison between the measured displacements and the numerical predictions at an interim stage of mining was carried out to assist in choosing the final sequences involved in completing the stope.

Jan 1, 1981

By E. Dalgaard

During linear friction welding of titanium alloy Ti-5A1-5V-5Mo-3Cr (Ti-5553), the weld zone exhibits beta (B) grain refinement and alpha (a) phase depletion that have the combined effect of deteriorating the mechanical performance of the weldment. In this work, linear friction welded Ti-5553 was subjected to pre- and post- weld heat treatments in order to determine the conditions under which a phase depletion could be mitigated in the weld zone and thermomechanically affected zone (TMAZ). The mechanical response of the welded samples to the heat treatments was determined by performing tensile testing at room temperature. While the pre-weld heat treatments had no significant effect, the post-weld heat treatments were instrumental in restoring the strength of the starting (heat-treated) material.

Jan 1, 2011

By R. J. Evans

The Combined Metals Reduction Co.'s plant is at Bauer, Utah. It was built primarily to treat ore from the Combined Metals mine at Pioche, Nevada. Shortly after its completion, the company acquired the old Honerine mine, and ores from this mine, as well as custom ores from widely scattered districts, are now being treated at the Bauer plant. Pioche Ore The Pioche ore, which comprises about 50 per cent. of the mill feed, occurs as a replacement of an impure thin-bedded limestone. The lime beddings are separated by thin layers of micaceous shale containing appreciable quantities of sericitc and graphite. The ore is an exeeptionally fine-grained, dense mixture of minerals and gangue, assaying approximately 0.03 oz. gold, 7.2 oz. silver, 7 per cent. lead, 15 per cent. zinc, 16 per cent. iron, 29 per cent. insoluble and 1.5 per cent,. lime. Of the total lead 7 per cent. is in the form of sulfate and carbonate. Approximately 10 per cent,. of the ore consists of chert nodules impregnated with barren pyrite; the nodules average 0.8 mm. in size, and ire extrcmely hard, compared with the other constituents of the ore. Microscopic examination of Pioche ore ground to 80 per cent . minus 150 nicsh shows pyrite, sphalerite and galena still attached. Early Attempts at Ore Dressing Metallurgists, both professional and those working for private companies, have been more or less familiar with the Pioche ore sinee. 1913; in fact, a total of 35 commercial and plant laboratories expenmented with the ore between 1913 and 1921. The work during this period was decidedly negative, it being seemingly impossible to effeet a satisfactory separation of the valuable minerals into marketable products. In 1913, it was recognized that fine grinding-—that is, about minus. : 200 mesh—-was required to liberate the minerals from one another, and from the gangue, but such fine grinding was not considertd practicable at this time.

Jan 1, 1928

By Golubkov OL, Fedotov PB, Shkylar FR

One of the fundamental parameters of the race- way is its extent (a{ o), which has a significant effect on the distribution of gas and material flows in the lower region of the furnace. pp The known relationships for determination of aC o in most cases link the length of the raceway with the parameters of the blast, while the para- meters of the coke layer, in which the raceway is formed, are either ignored or else expressed in terms which are difficult to determine experimen- tally. Furthermore, the coke combustion propert- ies are not always taken into account in current blast furnace operating practice with combined blast. A complex dimensionless parameter, which re- flects the properties of the interacting media, is the ratio of the kinetic energy of the hot, com- bined gas stream to the potential energy of the coke flow, burning at the tuyere in a gas of known composition. Statistical processing of experimental data on the extent of the raceway zone, obtained from literature and our own work on operational furnac- es, has led to a working formula of the following Form:

Jan 1, 1981

By K. Izumi

Ultra-grain refinement and high strengthening of metals by accumulative roll bonding (ARB) was widely reported. However, applications of ARB to magnesium alloys were rather limited. In this study, Mg-9%Li-1%Y sheets were applied to ARB at room temperature. Six 0.5 mm thick sheets were stacked and reduced into 0.5 mm thick by four passes. The procedure was repeated up to three cycles, so that the equivalent strain of 6.2 was applied. The sheets show dual phase structure with a (hcp) and ß (bcc). Grains elongates to the rolling direction with increasing number of ARB cycles. After three cycles, fragmented a grains with average size of about 300 nm are uniformly distributed. After the first cycle, the ultimate tensile strength increases to 180 MPa from 133 MPa, while the elongation decreases, however, still high (26%). The tensile strength slightly decreases by the second cycle and does not change at the third cycle. Meanwhile the elongation increases by the second cycle and the sheets show 41% of the elongation after the third cycle.

Jan 1, 2006

By Meyer C. F

The increasing use of continuous miners in the extraction of high coal seams has amplified the need for enhanced ventilation systems in the headings. Owing to larger face dimensions and higher production rates, more ventilating air is required to effectively dilute liberated methane to acceptable concentrations. However, the increased air quantities raise and entrain greater amounts of dust, to which the operator is subjected. Various methods (eg sprayfans, on-board scrubbers and jet fans) are used in various configurations and combinations to ventilate the headings. These arrangements generally result in a complex air flow pattern, which complicates achieving an optimum balance between diluting methane and minimising dust capture. In order to cost effectively investigate and propose solutions to this problem for the South African coal mining industry, the Division of Mining Technology has embarked on an extensive work program to evaluate various ventilation methods presently in use. Four currently generic ventilation patterns in various heading scenarios have been simulated using the Computational Fluid Dynamics (CFD) computer program. Evaluating these outputs against a predetermined set of criteria allows the best system for a particular situation to be chosen. The program also facilitates fine-tuning of an adopted system without incurring the cost and inconvenience of doing such tests in situ. This process not only provides solutions at significantly reduced costs, but also yields deeper insights into the factors affecting heading ventilation than hitherto possible.

Jan 1, 1995

By Forssberg KSE

The behaviour of cationic and anionic collector mixtures in the feldspar-quartz flotation system has been investigated througl conductivity, surface tension, zeta-potential and flotation studies. Tht results show the formation of molecular complexes between oppositel; charged collector ions through charge neutralisation. The molecular complexes are found to have a higher surface activity than the individua components. The mole ratio of the mixed composition is found to have, significant effect on flotation. Mole ratio less than unit} (anionic/cationic) of collector mixtures increases the flotation recoveries If the mole fraction of the anionic collector is greater than the moh fraction of cationic collector in a mixed composition, flotation ceases The flotation selectivity principally depends on the inherent differences it the surface charges of feldspar and quartz at the flotation pH values of

Jan 1, 1993

By Desmond Y. M. Lee

This paper presents a procedure to prepare input for the computerized pit design system at Iron Ore Company of Canada. The procedure is simple and requires very little training. Also, it is general enough to accept both bench (horizontal cross section) maps and section (vertical cross section) maps. The output of this procedure is data which represent blocks of ore and waste with dollar values based on mineral content. The ultimate pit design is presented in printer-generated graphs, with numbers indicating the depths of pit bottom walls. Roads are added manually by the engineer with the aid of other computer programs. Section maps and bench maps are also printed as part of the output of the ultimate pit design.

Jan 1, 1978

By Almon F. Robertson

This report is one of a series based upon investigations made and being made within the Missouri River Basin in Montana by engineers of the Bureau of Mines , Albany Branch , Mining Division . These investigations are being made primarily to provide preliminary information to the Department of Interior agencies and to others concerned with planning the proposed Federal power developments within the Missouri River Basin. This report has been designed to permit public distribution of the factual data obtained . Virtually all known metallic -mineral occurrences and some nonmetallic mineral deposits within Fergus County were investigated in 1948. The investigations cannot be considered complete , however , because some long inactive mines or prospects may have been missed . Most of the old mine and prospect openings now are caved ; many are completely inaccessible . Many of the claims located years ago have been abandoned ; others have been relocated under different names and ownerships . Because of such conditions , much of the information regarding their development and operation necessarily has been obtained from available Federal and State publications , supplemented by information provided by owners and local residents .

Jan 1, 1950

By P. R. Taylor

This work is concerned with the extraction of refractory metals using an electro-reduction process, in which a molten oxide melt, instead of halide, is used as the electrolyte. The process may provide an alternative method of producing refractory metals from their ores through use of a reverse-polarity direct current (DC) plasma arc heating process. In such a process, the plasma torch itself acts as an anode, and resulting liquid or solid product metals work as a cathode, whereas the molten oxide melt plays the role of an electron transfer layer. The focus of this study is: the electro-reduction of scheelite; vanadium pentoxide; and chromite. For the vanadium pentoxide, the proposed melt is mainly composed of CaO-V2O5/Li2O-B2O3-V2O5or FeO-CaO-SiO2-V2O5-Li2O with the addition of other alkali and alkaline metal oxides. In the case of scheelite ore, the SiO2-CaO-Li2O-WO3system is used as melt and metal aluminum or nickel could be used as a collecting media. As for the reduction of chromite ore, SiO2-CaO-Cr2O3-Li2O system with trace amount of CaF2is used as the melt. As a demonstration, chromium was successfully produced at a laboratory scale through the plasma driven electro-reduction process. One of the studied slags had a composition of 13.8% CaO; 4.9%CaF2; 36.4% Cr2O3; 6.9% Li2O; and 38.0% SiO2. Two observations are significant in this laboratory scale study. The first one was that the amount of Cr2O3and FeO, which were predominantly electronic conductors in the oxide melt, greatly affected the conducting mechanism of the melt. With high concentration of Cr2O3and FeO in the melt, the current efficiency was fairly low. In this case, chromium was found to be barely reduced because of electronic conducting mechanism. For example, with initial slag of 60% Cr2O3, no chromium was found reduced. With low concentration of Cr2O3and FeO in the studied melt, typically no more than 30% Cr2O3, it was observed that chromium was readily reduced due to the dominant ionic conducting mechanism. The second observation was that the addition of SiO2tothe melt helped to make the oxide melt more ionic, which was apparently desirable to the molten oxide electrolysis. However, high content of silica had a negative effect on the fluidity of the melt. This was resolved by adding trace amounts of CaF2to the melt. Therefore, by judicious selection of oxide melt, refractory metal oxides might be dissolved into it and yet the melt itself retains the required ionicity. A reverse-polarity DC plasma driven molten oxide electrolysis may prove to be a viable alternative route for the extractive metallurgy of refractory metals.

Jan 1, 2003

By C. V. O. Hughes

DIATOMACEOUS earth is probably the most widely used, and certainly the least well publicized, of the important non-metallics of the United States. The very multiplicity of the names by which this whitish earthy sediment is described has served to confuse its identity, and to dissipate a realization of its full importance.

Jan 3, 1953

By Moorrees C

Tests show how that temperature and rate of sparging to remove carbon dioxide determine the rate of precipitation and the chemical and physical properties of hydrated magnesium carbonates precipitated from clarified magnesium bicarbonate liquors derived from crude magnesia. At temperatures above 55°C the product is largely in the form ofhydromagnesite, Mg5(C03)4(OH)2.4H2O Between I5°C and 55°C the major product is nesquehonite, MgCO3·3H2O, although partial hydromagnesite precipitation can be induced by a high rate of aeration.As a result of the reduced time required to bring about greater than 95 per cent magnesium precipitation, the higher MgO content of the product, the ease of product recovery from the precipitation vessel, and the lower energy requirement for thermal decomposition of the precipitate to magnesia, it is preferable to precipitate hydromagnesite rather than nesquehonite. Moreover, the magnesia produced from hydromagnesite is somewhat more reactive than that formed from nesquehonite.Using precipitate calcination temperatures less than 1000°C, the chemical reactivities of the magnesias formed from both precipitates are greater than those of the crude magnesias derived from Savage River magnesite itself. The magnesias would be suitable for most uses developed for caustic-calcined magnesia. However, for refractory brick manufacture, it would be necessary to briquelle the caustic-calcined magnesia. adjust the CaO and SiO2 contents and sinter at temperatures in excess of 1600°C. This would bring about an increase in the bulk density and induce the appropriate chemical bonding reactions.Dead-burned magnesia produced from Savage River magnesite by the calcination/carbon dioxide route would have very low B2O3 contents, typically less than 0.0001 per cent.

Jan 1, 1985

By Roger T. Laine

"The Carswell structure, located in the western part of the Athabasca Basin, northern Saskatchewan, has been extensively explored since 1967. This exploration has been successful and lead to the discovery, in 1970, of the D sandstone-hosted unconformity related deposit. By the end of 1984, five additional basement-hosted unconformity related deposits had been delineated: the OP and N discovered in 1970, the Claude in 1971, the Dominique-Peter in 1981, and the Dominique-Janine in 1984. The D deposit has been mined out; the Claude open-pit has already produced more than 500 tonnes of uranium, the development of the Dominique-Peter underground mine (first phase) has been completed, and production from the latter started in 1985.All six deposits are located in the southern part of the Aphebian metamorphic core, 18 km in diameter, which has intruded at least 1250 metres of Helikian Athabasca Group sediments during a cryptoexplosion event at 480 Ma, unrelated to the emplacement of uranium mineralization. The metamorphic rocks, affected by the Hudsonian Orogeny, are divided in two lithostratrigraphic units: the Peter River gneiss, aluminous gneiss series, and the Earl River complex, mixed quartzofeldspathic and mafic gneiss series. A well developed regolith profile is recognizable in the south along the contact with the sandstone and inside the metamorphic core sometimes associated with conformable sandstone beds.Basement and sandstone-hosted uranium deposits show many similarities:-linkage to unconformity;-mineralogy and geochronology with a first phase mineralization characterized by a polymetallic sulphide-uraninite-brannerite assemblage dated at 1150 to 1050 Ma, a second phase characterized by a simple sulphide-uraninite assemblage dated at 890 to 820 Ma, and a third phase characterized by a pitchblende-hematite dated at 380 Ma; and,-linkage to early Hudsonian structures with remobilization of these structures during intense hydrothermal alteration resulting in Mg chlorite-illite halos."

Jan 1, 1986

By A. E. Reschke

Optimized mine planning of the Leeville Gold Mine, Nevada, necessitated the requirement for an average of 2540 tpd of high quality cemented rockfill (CRF) in primary stoping blocks and underhand cut and fill workings. To meet this requirement, a number of innovative design features were incorporated into the overall batching plant design. Foremost is the use of a dedicated skip to transfer crushed aggregate from surface down through the ventilation shaft to twin underground storage silos. Also, the use of a high shear colloidal mixer on surface to pre-slurry a cement/flyash binder with pipeline delivery to one of two separate underground CRF mixing stations was incorporated. Finally, the binder and aggregate are combined in a 9 m3 twin shaft compulsory type mixer before loading into teleram trucks for placement.

May 1, 2007

By H. Shaw

IT is now generally recognized that the gravitational method of geophysical surveying is a valuable aid in elucidating the geological structure of the subsoil and enables the practical geologist to deduce the presence of useful deposits. The particular suitability of the torsion balance to the location of large and important subterranean structures has given rise to a wide application of this method by many of the important oil companies in their search for future supplies, and so intense have been these efforts that little has been heard of the method in other connections, with the exception of occasional references to its application in the location of hidden deposits of metallic ores, salt and lignite, and a number of accounts of its use in the elucidation of geological structures. Its success in the location of salt domes is well known, and establishes it as one of the most important of the geophysical methods, especially for the indirect location of oil. In the British Isles, however, no large occurrence of oil is likely to be revealed, and here the practical application of the gravitational method has been restricted almost entirely to the search for ores. This type of survey possesses well marked characteristics, and presents a gravitational problem that has necessitated the development of a special and probably unusual plan of campaign, full details of which it is hoped will shortly be published. The problems and difficulties encountered in this work are of necessity fundamentally related to those met with in the search for oil by means of the torsion balance, but they also possess several special and distinctive features which undoubtedly differentiate them from the obstacles confronting the oil prospector, and which call for special consideration and treatment.

Jan 1, 1928

By J. A. Pigott

Undercut-and-fill mining is a method developed by the International Nickel Company to deal with abnormal pillar mining conditions at one of its mines. Results have been such that its use has been extended to normal, pillar recovery operations in other mines of the Company as a replacement for conventional square-set pillar mining. It is anticipated that the method will also largely replace square-set stoping at INCo mines, especially for mining at deep horizons.

Jan 1, 1962

By Siddall B

A brief review of the capabilities and practical limitations of blast simulation packages has been carried out. It is concluded that the simulators accurately reflect size distributions in the mid-ranges of 0.1 to 1.0 in, but are less reliable

Jan 1, 1998