Search Documents

By R Lau

In recently completed road tunnel projects in Queensland, such as the Airport Link and the Clem7 tunnels, there is a smoke duct running along the roof of the carriageways to extract smoke in case of fire. In New South Wales, no road tunnels have a smoke duct. In the Melbourne City Link tunnels, there is a small smoke duct running along the roof. All of the tunnels are safe as claimed by the designers and authorities. However, there is significant cost associated with providing a full size smoke duct compared with no smoke duct. This paper is going to present a comparison of the road tunnel safety with a smoke duct and those without one from a risk perspective. It further discusses the cost-effectiveness of such provisions and whether similar levels of safety could be achieved without a smoke duct.CITATION:Lau, R, 2014. Smoke duct or no smoke duct for road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 83–86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G. R. Love, C. C. Koch

The changes in superconducting properties with aging time have been studied ,for the pecipitation reaction in a Tc-30 at. pct V alloy. Superconducting critical temperature, upper critical field, and relative critical current density were determined by ac susceptibility techniques. Aging produces changes in critical temperature of both matrix and precipitate which can be rationalized by compositional effects. maximum flux pinning (critical current density) occurs at a time during aging when subgrain boundaries are completely decorated with precipitates and the subgrain centers remain precipitate -free. The particular effectiveness as barriers to flux motion of planar defects which enclose regions of low deject density is discussed. THE precipitation of a second phase can dramatically modify the superconducting properties of type I1 super-conductors. According to Livingston and Schadler1 one might expect changes in the primary, secondary, and tertiary superconducting properties of the material. Changes in matrix chemistry caused by precipitation can alter the fundamental superconducting parameters; critical temperature, Tc, and thermody-namic critical field, Hc. The concimitant changes in electron mean free path (reflected in normal state resistivity) can affect the critical fields Hc 1, IIc2, Hc3. Finally, the presence of precipitate particles may hinder the motion of flux lines and may considerably improve the current-carrying capacity in high-field superconductors. The influence of precipitation on superconducting properties has been studied in a number of systems.2 Magnetization measurements have been used to study the influence of precipitates on flux pinning in lead-base alloys by Livingston3 and Evetts et al4 In these alloys precipitates induced magnetic hysteresis and flux trapping. The amount of hysteresis increased with the volume fraction of precipitate and decreased with coarsening of the precipitate. Jn an Al-Zn alloy5 and an A1-Ag alloy6 the initial precipitate size was presumably smaller than a coherence length and coarsening increased magnetic hysteresis5 and critical current density.6 The influence of precipitation on superconducting properties has also been studied in several of the commercially interesting Ti-Nb7-10 and zr-Nb11 alloys. The maximum in critical current density for these alloys was confined to a narrow range of either isothermal aging time" or isochronal aging temperature7 during the precipitation reaction. Thus, experimental evidence and theoretical considerations suggest there is an optimum precipitate size, spacing, and density, and a critical composition with respect to the matrix for flux pinning. What these "optimum" values might be and the relative importance of each is still not clear, although a few generalizations can be made. It is generally accepted1' that particle sizes smaller than the coherence length or larger than the inter-flux line spacing are poor pinning centers. In high Hc2 materials, precipitate sizes for maximum values of critical current density lie in the range of 50 to 2000Å,9,7 and there are indications that increasing dissimilarity between precipitate and matrix produces increasing pinning force.13 Because of several interesting features of the aging reaction in a Tc-30 pct V alloy, we have chosen to study the influence of precipitation on the superconducting properties of this alloy. The physical metallurgy14 and a survey of the superconducting properties" of the Tc-V alloy system have been reported. The Tc-V phase diagram is presented in Fig. 1. At 1500°C the Tc-30 pct V alloy is in the single phase 6 field. Samples quenched from the 6-phase field have a CsCl structure X-ray diffraction pattern at room temperature and it has been proposed that the 6 structure is closely related to the bcc lattice.14 When held isothermally below the eutectoid temperature, 115O°C, the 6 phase decomposes into the CsCl and hcp phases.

Jan 1, 1970

By Sloan GJ, Lysnar RD

Since the of Bergstrand's Geo-dimeter in 1946, and Wadley's Tellurometer in 1956, there have been numerous Electromagnetic Distance Measurement (EDM) instruments produced throughout the world by a variety of companies.This form of measurement has not merely replaced other methods of measurement, but has caused considerable change of emphasis in survey techniques. Major control surveys are now being accomplished using trilateration instead of triangulation. The surveying of open cuts or engineering work may be done in a fraction of the time and, in the majority of cases, to a greater degree of accuracy than with older methods.It is surprising that with this new tech-nology and development of EDM equipment which is compact, easy to use and no longer so expen-sive, no advance has been made in underground surveying. If we look at equipment being used by the majority of mining companies, we see that there have been very few changes since the Second World War. Very little research has been carried out to enable the surveyor to do his work more easily in conditions which, at the very least. are hazardous.

Jan 1, 1984

By Howard J. Brown

The Lucerne Valley limestone mining district is in the San Bernardino Mountains, one of the major ranges in the Transverse Range Province of southern California. Several large limestone mining operations are present along the north range front in Lucerne Valley, and the area is one of the premier limestone mining districts in the country. Resources are contained in Paleozoic carbonate rocks that are part of a thick late Precambrian and Paleozoic sequence that uncomformably overlies crystalline basement. The district has been affected by multiple episodes of metamorphism and deformation, as well as by a complex sequence of late Cenozoic structural events. Detailed studies, however, have demonstrated that these rocks can be divided into formations correlatable with late Precambrian to Permian strata of the Cordilleran miogeocline. The district is the leading producer of white, high-purity calcium-carbonate products in western North America. Pluess-Staufer (California) Inc. mines and processes high-purity white limestone from extensive deposits, and is one of the largest producers of high-quality limestone fillers and extenders in the western United States. Major factors influencing the genesis of economic carbonate deposits in the district include depositional environment, post-depositional processes such as diagenesis, dolomitization and/or silicification, regional and/or contact metamorphism and associated intrusive activity, faulting, folding, uplift and erosion, and preservation from erosion. Regional geologic studies, detailed geologic mapping, intimate knowledge of stratigraphy, and recognition of complex structural relationships have proven to be invaluable tools in the discovery of high quality calcium carbonate deposits in the district.

Jan 1, 1987

By Clyde E. Williams

Estimates indicate a life of known Lake Superior iron ore reserves of 20 to 30 years. Although some believe the future ore supply will come from foreign sources and will be brought to interior points via the projected Great Lakes-St. Lawrence waterway, and others fear a displacement of the interior steel-producing districts to the Atlantic seaboard, the author has faith that American engineering skill will make possible the use of lean ores from the Lake Superior district. Three general types of Lake Superior ores and ore formations, that represent possible reserves and require beneficiation, are: (1) the wash ores of the western Mesabi range, (2) the partly leached hematitic formations, and (3) the oxidized but largely unleached iron formations. The total tonnage represented by (1) and (2) is not large, but the recovery of iron from present washery tailings would bring on the market the equivalent of nearly one million tons of wash ore, annually. Group 3 comprises the magnetic iron formation of the eastern Mesabi range, the hematitic formations including the taconites of the Mesabi range, and the iron formations of all the other ranges. These formations represent our future supply of iron ore. Their treatment requires intensive research because the bulk of the iron oxide and silica minerals exist in a finely disseminated condition. The possibilities of the adaptation of tables, oil flotation, and other processes warrant extensive study. Cheaper method of agglomeration of the concentrate is essential. Recent developments in better preparation and sizing of blast-furnace charges indicate that substitution of agglomerated ore for fines will increase furnace efficiency and output. If agglomerated beneficiated ore can be shown to rate a per-unit premium for iron contents over the base rate or a premium for structure, the payment of these would greatly assist in enlarging our iron ore supply. Since present methods of taxation of ore reserves, which encourage the rapid depletion of rich ores, will result in using up our rich ores and later on putting domestic producers at a disadvantage in competing with' foreign producers, it would seem highly provident to conserve our rich ores and to increase the use of beneficiated ores as soon as possible.

Jan 1, 1931

The phosphate pebble-bearing matrix in the Florida Phosphate Pebble Field has physical properties which make it readily adaptable to hydraulic transportation methods employing solids-handling pumps and pipelines. The abundance of water available, a practically flat terrain, low costs per ton-mile, and beneficiation of the matrix by agitation while being pumped have contributed to the popular choice of hydraulic transportation. Phosphate pebble mining in Florida, begun in the 1860's, first used high pressure water and solids-handling pumps for overburden removal about 1900. Removal of the average 25 ft of overburden was followed by hydraulic mining of the matrix, with 6-in. and 8-in. pumps handling 50 to 100 cu yds per hour being moved along the floor of the pit as they were advanced toward the face being undercut and slurried by hydraulic guns.

Jan 3, 1961

By A. L. Marshall, F. J Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

By A. L. Marshall, F. J. Norton

The object of this investigation was to make a comprehensive study of the degassing of molybdenum in order to determine how rigorous a treatment was necessary to completely remove sorbed gases from molybdenum electrodes in vacuum tubes. Some work has also been done with tungsten, nickel, iron and carbon. As a logical development of this work it has been shown that the gas is present throughout the body of the metal and a study has been made of the solubility of nitrogen in molybdenum and tungsten and the rate, of diffusion of nitrogen through molybdenum has been calculated. Tests were made on molybdenum from all the commercial sources and no difference was discovered in the nature of the gases present, the amounts or the ease of removal. The reason for this was apparent when a study was made of the manner in which gases are absorbed by gas-free molybdenum. It is necessary to heat molybdenum to 1760°C. in a vacuum of the order of 0.001 micron for a time which varies lineally with the thickness, in order to obtain a condition in which no further gas is evolved by the sample. A sample so degassed can be handled and subsequently assembled in a tube and then degassed readily. The gases obtained from molybdenum are carbon monoxide and nitrogen, the nitrogen being the more difficult to remove. Apparatus and Technique The apparatus is shown in Figs. I and 2. It consisted of two units, a degassing system and an analytical system. Each had a bake-out oven, as shown surrounding the systems in the sketches. The system , will be traced, starting from the sample in the degassing system. A water-cooled quartz chamber surrounded the sample. The high-frequency coil, which heated the sample, extended only around this chamber and was cooled by an air blast. High-frequency power of 1800-meter wave length was obtained from a self-rectifying oscillator circuit with a maximum power input of 20 kw. A graded seal connected the quartz to the rest of the apparatus, which was of hard glass. The temperature of the molybdenum sample was observed by an optical pyrometer through an optical window about 40 cm. distant from the sample. Since the object viewed under these conditions was not a black body, true temperature was not observed, but the so-called "brightness temperature." The correction of this to true temperature is discussed in a later section. The apparatus was taken apart just above the graded seal; the quartz chamber was slipped off, washed with nitric acid, water and alcohol, and dried by an air stream. The old sample was removed by unscrewing the lower nut, and the new

Jan 1, 1944

NEW MEMBERS The following list comprises the names of those persons who became members during the period Dec. 10, 1915 to Jan. 10, 1916. ANDERSON, FRANK BASIL, Min. Engr., Sampler, Copper Queen Cons. Min. Co., Bisbee, Ariz. BAILEY, LEWIS NEWTON, Min. -Engr 4227 St. James Place, Sail Diego, Cal. BELL, JAMES E., Min. Engr., Care Chile Exploration Co., Chuquicamata, Chile, South America. BONILLAS, YGNACIO SAFFORD, Min. Geol., Copper Queen Cons. Min. Co., Bisbee, Ariz. BRADLEY, GEORGE OLIVER, Mech. Engr Hobart Bldg., San Francisco, Cal. CLARK, GEORGE L., Min. Engr Vipond Mine, Schumacher, Ont., Canada. CONKLING, RICHARD A., Geol., Roxana Petroleum Co. of Oklahoma, Tulsa, Okla. GOHRING, W. B.. Geol., Supt. of Mines, Calumet and Arizona Min. Co., Warren, Ariz.

Jan 2, 1916

By M. Oliazadeh, A. Vazirizadeh

"The inclusion of small amounts of silicon, phosphorus and sulphur in iron ores or concentrates can have a profound effect on the steel making process and thus on the final iron and steel products. In nature however, it is inevitable that iron deposits contain unwanted elements. Each element has its own distinct effect on the final steel product. The effect of high silicon is the formation of gray iron. Phosphorus mainly increases hardness and strength, lowers solidus temperature and increases fluidity and cold shortness. Finally sulphur contamination causes cracks in the iron texture when smelting and forms white iron when casting. Overall, the acceptable level of phosphorus, sulphur and silica in the iron concentrate should be less than 0.04%, 0.15 % and 1.5 % respectively.Scarcity of high grade iron ores necessitates using lower grade ores with higher amounts of impurities. The purpose of iron concentrators is to increase iron grades to an appropriate level suitable for steel making as well as removing impurities. Although many impurities can be traced in the ore, the most predominant impurities are limited to one or two elements. In this paper the beneficiation methods for removing SiO2, P and S are presented, including flotation, and the parameters that need to be considered in the design of beneficiation plants are discussed. Finally industrial cases are discussed along with their metallurgical performance.INTRODUCTIONIn metal sector, value of iron ores and concentrates is determined by iron percentage as well ascontent of:• Useful elements (Mn, Ni, Cr, V, Ti): natural alloying elements in steel• Deleterious impurities (S, P, As, Zn, Pb, K, Na): impair metal properties or complicate operational process in blast furnace• Fluxing components (Si, Ca, Mg,, Al)Sulphur and copper result in red-short, phosphorus is the cause of cold brittleness and arsenic and copper decrease welding characteristics. Sulphur should not exceed 0.15 in commercial ore. Acceptable sulphur content in ores and concentrates for producing sinter and pellets is 0.6%max, as sintering and heat hardening of pellets remove sulphur 60-90%. Phosphorous content in ores, sinter and pellets is limited to 0.07%-0.15%. 0.00.1% As max, 0.1-0.2% Zn max and up to 0.2% Cu are allowed in iron-ore part of the blast furnace burden for the production of standard conversion pig iron. Slag-forming components are divided into basic oxides (Ca, Mg) and acidic (Si, Al). Higher ratios of basic to acidic oxides are preferred since this reduces raw fluxing material."

Jan 1, 2016

By R. O. Burt

The economics of recovering slimes by gravity concentration, except in a few highly specialized cases, was hampered by the lack of suit- able high capacity equipment. However, in the last decade increasing cost of power and reagents, coupled with the development of high capacity units, has led to a reappraisal of the benefits of slime gravity concentration. This paper seeks to analyze the merits of gravity concentration, and the constraints placed upon it by the laws of motion. It traces the recent developments of unit processes, and their application to a wide range of minerals. The economics of gravity concentration are also discussed.

Jan 1, 1980

By R. F. Bell, L. W. Eastwood, R. W. James

Among those concerned with the annealing and heat-treating of aluminum and aluminum alloys, it is well known that after co1d-working a coarser grain is usually produced by slow heating than hy more rapid heating. Consequently, for the control of the grain size produced by annealing or heat-treating cold-worked aluminum and aluminum alloys, the heating rate is of considerable practical importance. References in the current literature on the effect of heating rate are numerous, but it appears neither necessary nor desirable to give here a review of the former nark done on this subject. It became evident during some preliminary work on the recrystallizn-tion of aluminium and aluminum alloys that the effect of heating rate depended upon the type of microstructure of the metal. This observation led to the following study of the relationship of the type of microstructure of the alloy to the effect of the heating rate. Materials Investigated Analyses of the aluminum and aluminium alloys investigatted are given in Table 1. Three classes of material are listed, as follows: Class I.— Belonging to the first class are pure aluminium and aluminium containing a second constituent that is soluble in the aluminium matrix at

Jan 1, 1939

By R. F. Bell, R. W. James, L. W. Eastwood

Among those concerned with the annealing and heat-treating of aluminum and aluminum alloys, it is well known that after co1d-working a coarser grain is usually produced by slow heating than hy more rapid heating. Consequently, for the control of the grain size produced by annealing or heat-treating cold-worked aluminum and aluminum alloys, the heating rate is of considerable practical importance. References in the current literature on the effect of heating rate are numerous, but it appears neither necessary nor desirable to give here a review of the former nark done on this subject. It became evident during some preliminary work on the recrystallizn-tion of aluminium and aluminum alloys that the effect of heating rate depended upon the type of microstructure of the metal. This observation led to the following study of the relationship of the type of microstructure of the alloy to the effect of the heating rate. Materials Investigated Analyses of the aluminum and aluminium alloys investigatted are given in Table 1. Three classes of material are listed, as follows: Class I.— Belonging to the first class are pure aluminium and aluminium containing a second constituent that is soluble in the aluminium matrix at

Jan 1, 1939

By Robert C. Emmett, Donald A. Dahlstrom

FOR many years gravitational classification has been employed as a basic tool in beneficiation of minerals and coal. While improvements have been made to increase efficiency and fields of application, the basic flow pattern has remained relatively unchanged in most gravitational classifiers. Feed slurry is introduced into a settling pool wherein the coarser solids settle against either an upward or horizontal fluid current, or a combination of both, and are withdrawn in a concentrated underflow stream. The finer solids below the classification point possess too low a settling velocity and thus are primarily swept out through a weir overflow by the bulk of the fluid. Because of its simplicity, efficiency, and low power and maintenance costs, gravitational classification finds a wide acceptance for separations in the range of 20 to 325 mesh.

Jan 10, 1953

By Box JC

A comprehensive computer simulation has been developed for heap and dump leaching processes. It deals with complex chemical interactions, involving several minerals and reagents, which vary with time and location in the dump. The simulation is generally applic- able to ores of various metals extracted by different reagents. It requires only mineral- ogical data obtainable from drill cores and chemical data obtainable from the literature; there is no curve-fitting with adjustable parameters. Applications in designing testwork programmes, evaluating operating options, transferring experience to new situations and reducing uncertainty in long-term forecasts are described. Specific examples are included illustrating the potential of the simulation.

Jan 1, 1983

By H. D. Kline

Manganese ores have been mined in the Batesville district since 1849. Although not continuous over the intervening years, production had totaled approximately 432,000 tons of manganese ore and ferruginous manganese ore to the end of 1953. The ores occur in deposits, essentially low in manganese content, distributed over an east-west belt 24 miles long and 4 to 8 miles wide, the core of which is about 6 miles north of Batesville, Independence County. Although the reserves of high-grade ores in the district are comparatively small, the large deposits of subgrade ores and low-grade manganiferous material comprise potential sources of supply of manganese that may have increasing future importance. The manganese occurs as primary oxide and carbonate minerals in relatively flat-lying limestone and shale formations in which they were originally deposited and as oxides in residual clays resulting from decomposition of the shale and lime-stone. Most of the deposits underlie from a few to over a hundred feet of sedimentary chert, but many occur in the residual clays on exposed slopes of chert-covered hills.

Jan 1, 1956

By I. L. Feld

This report describes an attrition-grinding process and equipment for grinding coarse kaolins to the 2-micron particle-size range. The research was undertaken by the Bureau of Mines to devise an acceptable method for converting coarse kaolins, such as paper-filler-grade clays, to paper-coating-grade clays, thereby increasing the value and extending the life of the southeastern paper-clay deposits. The attrition-grinding process is basically the intense agitation of a slurry composed of the material to be ground, a granular grinding medium, and a suspending fluid. This process gave better particle-size reduction than that obtained by several other grinding methods. Results of batch tests in 5-and 10-inch-diameter attrition grinders demonstrated that a coarse kaolin containing about 13 percent minus 2-micron, equivalent spherical diameter (e.s.d.) particles was readily ground to give a product with 88 percent minus 2-micron e.s.d. material. Power consumption was reasonable in view of the increased value of the ground material. Comparison of particle-size reduction with power-consumption data for the two units indicated that better performance was obtained with the larger machine.

Jan 1, 1960

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The use of large AG/SAG mills in the mineral industry has been on the rise recently due to a significant reduction in the capital and operating costs for achieving significant increases in plant throughputs. The major reason for downtimes in these mills is the time taken for the replacement of broken or worn liners. This loss of “availability” of these units has a significant impact on the productivity of these plant operations. The ability to predict liner life time and its evolving shape could help to optimize these comminution operations. In the past decades, various models have been proposed to estimate liner wear rate, but because of their empirical nature they could only be used within certain limited operating conditions. In this research, a phenomenological model which could predict the liner wear rate was proposed and tested. This model considers parameters such as; operating conditions, liner hardness, pressure on the lifter, and, relative velocity of particles and mill shell. Data from industrially measured liner profiles were taken during the liner life time at the Sarcheshmeh and the Gol-E-Ghohar SAG mills to provide a solid base to calibrate and validate the model. The comparison of the model predictions with the actual measurements of the liner wear rate showed that the results were in a good agreement at both, the Sarcheshmeh (R2=0.94), and the Gol-E-Ghohar (R2=0.97) concentrators.INTRODUCTIONAG/SAG mills are one of the most important technologies in the mineral processing industry in the recent decades. The “Availability” of these units in a plant operation is one of the most important economic parameter for evaluating their performance. The major reason for the downtime of these mills affecting their “availability”, is the time required to change worn or broken liners (Yahyaei, Banisi, & Hadizadeh, 2009; Maleki-Moghaddam, Yahyaei, & Banisi, 2012). The knowledge about the magnitude and profile of liner wear not only enables more accurate liner life estimation to prevent unwanted interruptions of the SAG milling in mineral processing plants and more strategically plan the scheduled mill outages for liner changes. It also could provide key information needed to select an appropriate liner design (Yahyaei et al., 2009; Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010a)."

Jan 1, 2016

By Stanley J. LeFond

Jan 1, 1985

By Bonelli A. Julio

"El presente trabajo señala la lixiviabilidad de los minerales marginales y otros materiales de desecho dentro de la pequeña y mediana minería a traves de la técnica de lixiviación ácido bacteriana y la recuperación de cobre por cementación y chatarra de fierro. Asimismo, se revisa los resultados del PADT Cobre y se analiza el planteamiento de los estudios de prefactibilidad en tiempos reducidos, cuyo mecanismo evalúa la incorporación de unmodelo cinético para predecir extracciones de cobre en el proceso de lixiviación bacteriana en montones, puesto que fue probado satisfactoriamente con las pilas piloto de Toromocho, yacimiento polimetállico ubicado en la Sierra Central perteneciente a CENTROMIN-Perú. "

Oct 14, 1980