Search Documents

By Holbrook G. Botset

Experiments performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This conclusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely consolidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be introduced was the cementing material. Experimental Procedure A comparatively limited assortment of sandstones was available for the selection of the experimental material. Of these, the Nichols buff sandstone appeared to be most suitable. It gives no visual evidence of any bedding planes, it has a firm structure, permitting easy handling, and its permeability is about 0.5 darcy. Its only disadvantage is the fact that it contains an appreciable amount of ferric oxide which, for experiments involving water, will hydrate and reduce the permeability. This

Jan 1, 1940

By Holbrook G. Botset

Experiments performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This conclusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely consolidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be introduced was the cementing material. Experimental Procedure A comparatively limited assortment of sandstones was available for the selection of the experimental material. Of these, the Nichols buff sandstone appeared to be most suitable. It gives no visual evidence of any bedding planes, it has a firm structure, permitting easy handling, and its permeability is about 0.5 darcy. Its only disadvantage is the fact that it contains an appreciable amount of ferric oxide which, for experiments involving water, will hydrate and reduce the permeability. This

Jan 1, 1940

By G. A. Reinhardt, Albert Sauveur

Although many metallurgists know that some pearlitic special steels can be made troostitic, martensitic, and even austenitic, without quenching, and, therefore, without exposing them to the dangers of the quenching-bath, the practical significance of such possibility does not seem to have received the attention it deserves. Let us recall briefly the mechanism of the transformation alluded to. In Fig. 1 (after Guillet) is shown the constitutional diagram of nickel-steel; that is, of alloys of iron, carbon, and nickel. Any steel the composition of which falls within the area LPO is pearlitic after slow cooling; any steel the composition of which is represented by a point within the area MLO is martensitic, and any steel within the area MNO is austenitic. Starting with pearlitic steel, then by increasing the carbon-content or the nickel-content, or both, the metal becomes marten-sitic and eventually austenitic; that is, its composition crosses first the boundary-line LO and then the line MO—and it remains martensitic or austenitic after slow (air) cooling.' We have in this way imparted to the metal without quenching it the properties of hardened carbon-steel. In other words, the steel is now self-hardening; Nickel cannot be introduced into solid steel, but by the well-known process of case-hardening it

Jan 1, 1913

By Edward Hyde

THE HIGH-TEMPERATURE SCALE IN OPTICAL PYROMETRY AT the basis of optical pyrometry lie the theoretical and experimental data of the so-called blackbody. The black body is essentially a theoretical conception, with certain simple properties attributed to it -fundamentally, the property that its radiation at any temperature is a unique function of the temperature and does not involve any other variables. As a theoretical conception, an equation has been developed by Boltzmann connecting the total radiant power with the temperature, and another equation by Planck connecting the distribution of radiant power throughout the spectrum with the temperature. The integral of the latter with respect to wave-length conduces to the former and permits the evaluation of the constant c1 of the Planck equation, ass given in the form. J-= cl?-5 c2 (1) e ? T ? 1 assuming that the constant Q of the Stefan-Boltzmann law E=a(T4-T40) is known. The other constant c2 is arrived at by other methods, which will be discussed later. This equation for the black body lies at the foundation of optical pyrometry. To make the discussion complete, it should be stated that the theoretical black body is quite closely realized by a hollow enclosure with walls at a uniform temperature and radiating through a small orifice. The electrically heated black body, first introduced by Lummer and Kurlbaum, is an essential part of the equipment of a pyrometric research or testing laboratory. Numerous investigations have shown that its radiation conforms to that of the theoretical black body within experimental errors. Hence by operating the electrically heated black body at the melting point of some pure metal for which the temperature of melting has been determined on the vas scale. a standard is obtained for comparison with

Jan 9, 1919

By W. L. Zeigler

During the middle 1880's, shortly after the discovery of silver-lead ores in the Coeur d'Alene district of northern Idaho, it became apparent that concentration of the ores would be necessary to obtain a profitable product. Too much siliceous material was present for direct smelting, and the majority of the ores found at depth were too low in metallic content for economic smelting processes at the time. As the ores occurred in quartzite shear zones with siderite and quartz gangue, a large quantity of waste material was present in all the mines. As the galena was not finely disseminated, this made possible relatively good extraction of the argentiferous galena by coarse concentration. The first concentrators consisted mainly of coarse crushing, screening and jigging, principally by Harz jigs, the slimes being treated on buddles. Later Wilfley tables took the place of sand jigs and vanners superseded the buddles. Because of the marketing conditions, no attempt was made until 1900 to effect a recovery on the zinc minerals present, which were found associated in varying amounts with the galena. All through this period, the greater part of the production was obtained from mines containing ore assaying high in lead and low in zinc. Parts of some ore bodies would be reversed in this respect, so that ores high in zinc were left intact. During the decade after 1910, several important mines, The Success and The Interstate Callahan, containing ores high in zinc, were put into operation and were a material aid in the needed zinc production during World War I. Gravity concentration by jigs and tables was used during this period, with bulk flotation increasing in popularity for the treatment of the fine material that had already been treated by ordinary slime concentrating machinery. No extra fine grinding for flotation concentration was thought profitable at the time. Tailings Discharged into Streams From the start of mining and milling operations in this district until 1904, no attempt was made by the various mills in the upper district to impound or stack their tailings. They discharged them directly into the adjacent creeks or streams, to be carried away by high water. The Bunker Hill and Sullivan and the Last Chance mines, both in the relatively flat valley of the district, stacked huge piles of the coarse jig tailings on the near-by river bottom. Rain and snowfall are heavy in the Coeur d'Alene district, as it is on the heavily timbered Pacific slope of the Bitter Root Mountains. A heavy runoff occurs every spring and there is an occasional flood of disastrous proportions when warm "Chinook" winds accompanied by rain

Jan 1, 1949

By G. J. Simandl

Jade is a commercial term encompassing green, white, black or yellow-brown jadeitite and nephrite. Jadeitite consists of Na-rich pyroxene, whereas nephrite consists of prismatic to acicular amphiboles of the tremolite-actinolite series forming bundles that are randomly oriented and interlocked. Nephrite is tougher (harder to break) than jadeitite. Its fracture strength is about 200 MN/m2 whereas that of jadeitite is about 100 MN/m2. On the other hand, jadeitite has a higher hardness (7 compared to 6.5 on the Mohs scale). There are over fifty known nephrite occurrences in British Columbia (B.C.). These occurrences consist of individual blocks, boulder fields, talus blocks and in situ occurrences. Most of the in situ occurrences are lens or cigar shaped. They occur at, or near the contact of ultramafic/mafic rocks (mainly serpentinites) with cherts, and other metasedimentary or igneous felsic rocks of Mississippian to Jurassic oceanic terranes such as Cache Creek and Slide Mountain. These contacts are commonly interpreted as shear/fault related. In general, it is believed that the B.C. nephrite formed by metasomatic exchange between ultramafic and silica-bearing rocks. Impurities in B.C. nephrite are spinel group minerals (chromite, magnetite, picolite), diopside, uvarovite, titanite, chlorite, and talc. Jadeitite is slightly denser than nephrite and good quality material sinks in methyl iodine. There are no known jadeitite occurrences of economic interest in B.C., but there are at least four geographic areas where favorable lithologies, and metamorphic conditions (Pn) required for the formation of jadeitite coincide. These are Bridge River, Pinchi Lake, Dease Lake, and Jennings River. These areas are known to contain small concentrations of jadeite, or are characterized by blueschist or eclogite-grade metamorphic conditions. Rhodonite and pyroxmangite are MnSi03 polymorphs. These minerals are pyroxenoids and are macroscopically and microscopically very similar. For brevity, both are grouped together under the term "rhodonite". Most of the B.C. occurrences are hosted by late Paleozoic chert sequences and are lens shaped and concordant. The common association of rhodonite with iron formations, jasperoids, and/or volcanogenic sulphide deposits in southwestern B.C. permits the delineation of favorable horizons using magnetic or electro-magnetic geophysical methods. Geographic associations between manganese showings and sulphide deposits, and the hydrothermal chemical signature of the rhodonite occurrences from this area, suggest a genetic link between rhodonite and volcanogenic sulphide deposits. The typical rhodonite rocks consist of rhodonite, pyroxmangite, neotocite, black amorphous Mn-oxides, Mn-bearing garnet, ± epidote, ±chlorite, ±rhodochrosite, ± parakutnah-orite, ± Mn-bearing calcite, ± iron oxides and hydroxides. Garnet ± epidote forms yellow patches and layers within the rhodonite. Within some of the rhodonite occurrences, the garnet is altered to chlorite. Rhodonite-bearing rock is commonly cross cut by secondary manganese oxide veins, creating a characteristic web-like texture. In several localities, the contorted bedding planes are readily recognized. Mn-calcite and quartz also crosscut rhodonite. Rhodonite deposits hosted by high grade metamorphic rocks may contain pyroxmangite. Rhodonite is an important gemstone and ornamental stone in B.C., second only to nephrite in dollar value. B.C. nephrite and rhodonite have been used for the past 100 years in local jewelry and ornamental applications. More recently they have been used in table tops, and they have potential as upscale materials in tile-making. There may be a market for tiles made from lower grade materials that were previously extracted and stockpiled. The prices of nephrite, jadeitite, and rhodonite vary widely with quality, but gem and ornamental grade stones are relatively highly priced materials and they trade world-wide.

Jan 1, 2001

By Stephen L. Bolivar, Susan H. Balog, Thomas A. Weaver

A data-classification scheme was developed to detect potential uranium mineralization in the Montrose l º x 2º quadrangle, Colorado. The methodology developed is a rapid and efficient method of resource evaluation on a reconnaissance scale. The necessary techniques were developed and refined to digitize, integrate, and register various large geological, geochemical, and geophysical data sets for the Montrose quadrangle, Colorado, using a grid resolution of 1 km. All data sets for the Montrose quadrangle were registered to the Universal Trans- verse Mercator projection. The data sets include hydrogeochemical and stream sediment analyses for 23 elements, uranium-to-thorium ratios, airborne geo- physical survey data, the locations of 90 uranium occurrences, and a geologic map (scale 1:250 000). Geochemical samples were collected from 3965 locations in the 19 200 km2 quadrangle; aerial data were collected on flight lines flown with 3-5 km spacings. These data sets were smoothed by universal kriging and interpolated to a 179 x 119 rectangular grid (each grid block is 1 km2). A mylar transparency of the geologic map was prepared and digitized. All possible combinations of three, for all data sets, were examined for general geologic correlations by utilizing a color microfilm output. Subsets of data were further examined for selected test areas. A classification scheme for uranium mineralization, based on selected test areas in the Cochetopa uranium district, is presented. Areas favorable for uranium mineralization, based on this scheme, were identified and are discussed.

Jan 1, 1982

The Bradford Process, Australian Patent No. 11253, has had considerable application in the treatment plants of Broken Hill mining companies, and is at present being used by the North Broken Hill Limited for the treatment of weathered slime accumulations.The "Mining and Scientific Press," of 28th September, 1918, describes the Bradford Process at Broken Hill, specially featuring its application to slime material at the Proprietary mine-the home of the process.The points then stressed for galena flotation were acidulated slime pulp (0.025 to 0.030% H2S04) at temperature 85° to 90° F. and suitable time contact, with 1.5 to 2 lb. of sodium hyposulphite (per ton on slime) to permit the released S02 to "wet" or depressthe blende mineral. Also 1.0 to 1.3 lb. of crude sulphur (per ton on slime) was burnt, to supply S02 for keeping the lead concentrate clean during flotation. Pulp density varied from 23 to 26% solids. Since 1918 the process has been simplified in its application.Acidity of circuit, temperature, and sodium hyposulphite have been dispensed with, and now the S02 is practically all obtained by burning crude sulphur. I The plant units now employed for control and absorption of S02 gas constitute the main advance made in process, and these, with other details, are fully explained in this paper.APPLICATION AT BROKEN HILL NORTHThe existing North Broken Hill Limited gravity mill commenced operations on 9th September, 1909.

Jan 1, 1929

For some time fine coal (-0.5 mm) flot ation has been considered as a bulk flotation problem. Combinations of hydrocarbon oils and frothers have been used as surface active agents in coal flotation. The selectivity of the flotation process has always been poor in such cases. With the increase in fine coal production due to mining methods and coal handling systems, optimisation of fine coal treatment.has become important. Petrographic and mineralogical composit- ions of coal particles have been reported to influence their flotability. The problem becomes more complex due to surface oxidation of coal and the presence of slime forming clay minerals in the run of mine coal. In this paper, the flotation problem is examined on the basis of various constituents of coal and their associated gangue minerals. The selection of reagents has been suggested on the basis of their surface chemical properties. Factors such as surface modific- ation of coal and gangue materials, flotation kinetics and hydrocarbon oil - coal inter- action have been critically evaluated to improve fine coal flotation recovery.

Jan 1, 1978

By G. Caetani, E. Burt

Jan 1, 1907

By Barry W. Klein

The U.S. economy was considerably stronger in 1976 than in 1974 or 1975. Real gross national product (GNP) rose sharply in the first quarter of 1976 and then increased at a more moderate rate for the remainder of the year. The unemployment rate fell until June and then increased for moat of the remainder of the year, finishing at the same rate as it had started the year. The inflation rate continued to decline in 1976. Reasons for the relatively low rate (compared with those of 1974 and 1975) included small increases in food prices and only moderate increases in energy prices. Total U.S. output measured in terms of GNP increased 11.6% in 1976. Real GNP in 1972 constant dollars rose 6.2%. Inflation as measured by the implicit price deflator increased 5.1%. In real terms, gross private domestic investment for residential structures rose 22.7% in 1976 after declining 14.7%a in 1975; State and local Government expenditures increased 1.4% in 1976; and personal consumption expenditures for services rose 4.5%. The Federal Reserve Board (FRB) index of industrial production increased 10.2%.

Jan 1, 1978

By R. G. McDonald

"High iron solution concentrations often result in the formation of basic ferric sulfate during the high temperature oxidation of sulfidic materials such as base metal and refractory gold concentrates. Consequently, the “Hot Cure Process” followed by limestone neutralization is required to facilitate subsequent processing and/or disposal of the leach residue. The present paper discusses strategies that can be employed to influence the composition and nature of the high-iron content leach residues produced during pressure leaching.INTRODUCTION Control of iron deportment in hydrometallurgical processing remains a key challenge for a range of reasons. Strategies generally relate to the control of conditions under which iron is optimally rejected (Demopoulos, 2009). Supersaturation provides the driving force for crystallization and this can be controlled by a number of factors that include (1) pH and/or Eh control, (2) the presence of matrix anions and impurities, (3) dilution, (4) complexation and dissociation and (5) manipulation of the rate at which the metal to be precipitated is released to solution. Each of these factors is impacted by temperature. Good control of crystallization is essential to the control of precipitate properties such as the degree of crystallinity, stability, particle size and quality which covers both the extent of impurity uptake and suitability of the precipitate for waste disposal. The quality and properties of iron precipitates in turn can impact downstream processing. It is the aim of this paper to discuss the generation of iron-containing residues produced during the pressure oxidation of sulfidic ores and concentrates and how the nature of these can be controlled to potentially facilitate further processing. A brief overview of several related topics will now be given and include, where relevant, discussion of work undertaken in our laboratories. In addition, brief discussions of selected process options that enable good control of iron rejection will be provided."

Jan 1, 2016

By George Ashley

IT has been said that the Pittsburgh bed is the most valuable single mineral deposit yet known to man. The figures in Table 1 are presented in substantiation of that claim. TABLE 1.-Pittsburgh Coal Bed to Dec. 31, 1934 Estimated Recov- State Thousands of ( Value erable Reserves Tons Mined (1935), Thousands of Tons Pennsylvania 3,144,000 $4,922,000 7,500,000 Ohio 493,391 843,699 3,000,000 West Virginia 650,000 1,027,000 5,500,000 Maryland 183,224 254,681 20,000 Totals 4,470,615 $7,047,380 16,020,000 PRODUCTION AND VALUE In order that the figures of Table 1 may have any weight, a statement must be made to show how they were arrived at. Because, to the writer's knowledge, no accurate separate figures ever have been kept of the production and value of the Pittsburgh coal bed, the states will be considered separately.

Jan 1, 1936

By G. C. Lipsyy

ALL mineral production? of Can11.da is transported in a mine car at some stage during its extraction. There are as many types and varieties of mine cars as there are of mines. Many of the cars in use were developed in the blacksmith shop. Others were designed by engineers and improved by the mine foremen and the mechanics. Every mine car has the ideas of miner, blacksmith, mechanic, and engineer incorporated in it. Many of these ideas are not generally known. This paper was written to make at least some of this information available to the mining industry. In drawings, tables, and notes, it gives all the important details pertaining to the cars. It .does not recommend any particular type of car for any particular piece of work, nor does it present drawings from which a car can be built. It gives the engineer or master mechanic information on many cars which he can apply to his own particular problems. It is hoped that this information will be of use to mine operators. If a few new ideas are conceived as a result of the paper, the author will feel that the effort of compiling it has been worth while. In order to obtain the data for the preparation of the paper, a questionnaire, copy of which is here reproduced, was sent to all the operating mining companies in Canada. An accompanying letter briefly explained the purpose of the paper and asked for co-operation in furnishing as complete information as possible.

Jan 1, 1945

An iridium oxide coated titanium electrode was tested as anode in copper electrowinning. Initial results confmed that the DSA-type anode was significantly more active for oxygen evolution than traditional lead anodes. However, during longer runs, the anode potential was observed to increase linearly at a rate of 220 mV/year. Scanning elecuon microscopy (SEM) and energy dispersive spectroscopy (EDS) showed that the anode passivation could be attributed to elecuochemical dissolution of the coating. The effect on the anode potential of organic additives (glue and thiourea) and lead in solution was also examined. A preliminary economic evaluation of the anodes is given.

Jan 1, 1992

By Zoltan F. Oszter

The frictional resistance to motion of a belt conveyor has always been a subject of intensive studies and research by engineers throughout the years. Numerous informations have been developed by analysing series of field tests on belt conveyors of different characteristics and carrying different materials at various capacities. Within certain limits of weight per unit length and tension, the theoretical considerations and the analysis of the field tests, both in the US and abroad, resulted in the development of similar formulas. In general these formulas are safe to use up to the following limits:

Jan 1, 1977

By T Goswami, M Edmondson

Henry Walker Eltin (HWE) are the mining contractors for Gloucester Coal at Stratford mine, which is in an environmentally sensitive area in the Avon Valley, NSW, Australia. Normal blasting at Stratford is done in a æstand upÆ or æbox cutÆ mode to suit the truck and shovel operations. Recently an opportunity of doing a throw blast became available when part of a ramp had to be blasted to accommodate changes to the pit design while not damaging the remainder of the ramp. The objective was to maximise throw into the void in order to minimise excavation costs by reducing the amount of overburden to be moved by the excavation fleet. It was necessary that the best result be achieved while staying within the vibration and airblast limits at a neighbouring property and nearby township. Both objectives were achieved through the application of OricaÆs knowledge of blast design, modelling and i-konTM electronic detonators. The i-kon system was used because of its known benefits in cast blasting and environmental control. The i-kon system provides the blaster with much greater accuracy, control and the flexibility to tailor blast designs. It has been found previously to enhance blast throw and provide cleaner high walls (Brent, 2002). The blast was a success, producing a muckpile with a high degree of looseness and consistent fragmentation, with an average throw to final spoil position of 37.5 per cent. This was achieved without any environmental exceedance. In addition, high speed filming showed that the coal edge had remained largely in place, indicating minimal coal loss. The results exceeded the expectations of HWE Stratford and the overall cost savings to HWE Stratford from this blast were recognised to be substantial. Further throw blasting opportunities at Stratford have been followed using the i-kon system to maximise benefits.

Jan 1, 2003

By D Wilson, E Nagy, R A. Augsten, R R. Vandebeek, R L. Guilbeault

The Canadian Explosives Research Laboratory (CERL), is evaluating the status of the Schedule IV explosives container as it presently pertains to the industry. The Schedule IV container serves the same purpose in Canada as the IME 22 container does in the United States. That is, to transport detonators on the same vehicle which is carrying explosives.

Jan 1, 1990

By Charles E. Nelson

THIS paper will outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as jar as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper and will be discussed briefly.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, this paper will deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. The outline of this discussion will closely follow that of an earlier paper,2 with such changes and additions as seem necessary to bring it up to date. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux, which provides protection during melting and a molten pool of flux into which the solid magnesium melts. The flux is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies;, on quiet standing, it separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is desirable. The open-pot method is used generally in the following processes: (I) alloying and remelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protection and refining qualities, and then drys out or thickens after a time, leaving a protecting crust on the pot surface until the time of casting. At that time it can be readily skimmed off or held back, thus allowing the contents of the crucible to

Jan 1, 1946

By M. J. Pazuchanics

This U.S. Bureau of Mines report presents results from an ongoing investigation of the use of adaptive signal discriminating methods to distinguish between cutting coal and cutting mine rock. Bit-cutting forces and tool vibration were measured in the laboratory as a linear-cutting apparatus (LCA) made constant-depth cuts in coal, sandstone, and shale test specimens. A portion of the collected data has been analyzed and some preliminary results are given here. The influence of data bandwidth, data window size, number of signal features, and voting among classifiers on classification performance are noted. Results to date, based on ideal-cutting conditions and simple geologic materials, indicate that of the four classifiers tested there appears to be no single best classifier. Usually, classification accuracy showed slight improvement as the number of features considered for classification increased. The highest classification accuracies were achieved when voting was conducted among classifiers followed by voting among force components.

Jan 1, 1991