Search Documents

By Quanzhong Gu

Stability of a pre-exnacted recovery room plays a vital role when longwall face approaches and during a longwall face move. In an attempt to extend the application of pumpable cribs into recovery room support and to limit roof bolt installation when a longwall face approaches the recovery room, yieldable and cuttable pumpable cribs (YCPC) were employed in the recovery room at the northern West Virginia mine. The YCPC consists of two layers of materials with different strengths. This allows considerable deformation from the floor and/or roof by sacrificing the soft layer while maintaining relatively high load capacity under mining¬induced front abutment loads. The thickness and stiffness of the soft layer, installation and quality control are the key factors when using the Yieldable and Cuttable Pumpable Crib to stabilize longwall recovery room- Underground observation and monitoring results show that the Yieldable and Cuttable Pumpable Crib is a viable solution to insure stability of the recovery room and can save at least two days for a longwall face move at the mine.

Jan 1, 2004

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980

By Allen Kinney, P. T. Freeport

This paper presents the methodology for final wall-controlled blasting utilized at the Grasberg Mine. The resulting optimized slopes representa14%and17% increase to bench face angle (BFA) and inter-ramp slope angle (ISA), respectively. The corresponding increase in both copper and gold recovery was more than 40% greater than forecast for each material. The Grasberg open pit mine is located in the remote jungle province of West Papua Indonesia, at an elevation of 4,200 meters(13,780 ft).With a diameter of approximately 3.5km(2.2 mi), anddepthover1.2km(0.7 mi),P.T. Freeport Indonesia (PTFI)has mined billions of tons of rock from one of the world’s largest gold and copper deposits. Grasberg Operation and Engineering implemented a quality driven slope optimization program for the final pushback, with the goal to safely increase recoverable metal through steeper slopes, while utilizing existing infrastructure and equipment. This paper focuses on controlled blasting initiatives, blast monitoring, and as-built slope measurement tracking, although many groups contributed to the success of Grasberg slope optimization. The potential slope optimization area was divided into two sections based on geologic assessment: Area A at radial 200°-270° and Area B at radial 270°-360°. Original slope designs for areas A and B specified ISAs of 51° and 52°, respectively, with all BFAs in the pit at 70°. Through continuous development, collaboration and achievement, the Grasberg final pit accomplished a BFA increase to 80°for all areas, and an ISA increase from 51° to 56°in Area A, and 52°to 60° in Area B.

By Muhammad I. Kabir

A new minitest of in situ uranium leaching processes at reservoir conditions is proposed. The test which consists of a single observation/ production well and two observation wells is designed to permit the evaluation of both restoration and leaching parameters. It is shown that by using a straight forward history matching procedure, sometimes called a type curve analysis, both the rate of leaching and the ultimate uranium recovery can be evaluated based on the results of the test. Type curves are presented for the case in which the reaction rate is kinetically controlled and there are no other minerals competing for oxidant. Other situations can be approached using the same techniques as those presented here.

Jan 1, 1981

By C. E. Abbott

The Birmingham district, Alabama, is distinctive in the proximity to one another of its deposits of iron ore, coal and flux. These three basic requisites for the making of iron and steel are found within a radius of 10 miles. Both dolomite and limestone are produced, the former for blast-furnace flux and the latter for basic open-hearth operations. The Tennessee Coal, Iron and Railroad Co., a subsidiary of the United States Steel Corporation, operates a limestone mine at Muscoda, near Bessemer, 12 miles southwest of Birmingham, served by its own railroad transportation system. The mine has a capacity of 130 tons per hour. Average analyses of a recent month's production arc as follows: Fe²zO³ SiO² Al²O³ CaCO³ MgCO³ Lump, percent............................. 0.51 0.22 98.63 0.14 Crushed and washed, per cent,................ 0.70 0.26 98.36 0.18 Lump stone, 2 1/2 to 755 in., is used in open-hearth operations at Fairfield Steel Works. Fine crushed and washed stone, 1% to 0.063 in., is calcined at the lime-burning plant and used for lime charges at the Ensley open hearths. Geology The district's deposits of hematite ore occur in the Clinton formation, and the limestone beds mined are stratigraphically 330 ft. above the ore beds worked. A cross section on the center line of the mine is shown in Fig. 1. This limestone formation, 130 ft. thick, is in the Warsaw horizon of the Lower Mississippian. It lies above 100 ft. of Fort Payne chert, which is immediately above the Clinton formation, and is composcd of layers of chert and cherty limestone, approximately 50 per cent of the material being pure chert. The chert is extremely hard, and the cost of driving raises through it is very high. Both iron ore and limestone deposits lie on the southwest limb of the Jones Valley anticline, the formations dipping from 15' to 32' to the southeast. The iron-ore seam outcrops along the crest of Red Mountain, a ridge with northeast-southwest trend rising 200 to 300 ft. above Jones and Shades valleys at the

Jan 1, 1938

By C. E. Abbott

The Birmingham district, Alabama, is distinctive in the proximity to one another of its deposits of iron ore, coal and flux. These three basic requisites for the making of iron and steel are found within a radius of 10 miles. Both dolomite and limestone are produced, the former for blast-furnace flux and the latter for basic open-hearth operations. The Tennessee Coal, Iron and Railroad Co., a subsidiary of the United States Steel Corporation, operates a limestone mine at Muscoda, near Bessemer, 12 miles southwest of Birmingham, served by its own railroad transportation system. The mine has a capacity of 130 tons per hour. Average analyses of a recent month's production arc as follows: Fe²zO³ SiO² Al²O³ CaCO³ MgCO³ Lump, percent............................. 0.51 0.22 98.63 0.14 Crushed and washed, per cent,................ 0.70 0.26 98.36 0.18 Lump stone, 2 1/2 to 755 in., is used in open-hearth operations at Fairfield Steel Works. Fine crushed and washed stone, 1% to 0.063 in., is calcined at the lime-burning plant and used for lime charges at the Ensley open hearths. Geology The district's deposits of hematite ore occur in the Clinton formation, and the limestone beds mined are stratigraphically 330 ft. above the ore beds worked. A cross section on the center line of the mine is shown in Fig. 1. This limestone formation, 130 ft. thick, is in the Warsaw horizon of the Lower Mississippian. It lies above 100 ft. of Fort Payne chert, which is immediately above the Clinton formation, and is composcd of layers of chert and cherty limestone, approximately 50 per cent of the material being pure chert. The chert is extremely hard, and the cost of driving raises through it is very high. Both iron ore and limestone deposits lie on the southwest limb of the Jones Valley anticline, the formations dipping from 15' to 32' to the southeast. The iron-ore seam outcrops along the crest of Red Mountain, a ridge with northeast-southwest trend rising 200 to 300 ft. above Jones and Shades valleys at the

Jan 1, 1938

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS GENTLEMEN: Submitted herewith are the report of the Treasurer for the year 1945 and reports for the same year of the following standing committees: Membership, Admissions, Papers and Publications, Mining and ' Metallurgy (Magazine), and Library. To these reports you are referred for additional details. Membership Membership, counting all categories other than Student Associateship, continues the upward trend of the last 10 years, reaching a total, as shown in Table 1, of 12,081. The net gain of 406 would

Jan 1, 1944

Discussion of the paper of G. K. Burgess and J. J. Crowe, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2537 to 2591. HENRY M. Howe, New York, N. Y. :-I think we can hardly rate the importance of the entry of the Bureau of Standards into our field. There is no body in the world that is better fitted to undertake this work than that Bureau, and it is work which really calls for the aid of some national organization. The skill and care with which this work has been done speaks for itself. It is very striking that within a very few months the distinguished English investigator, Professor Carpenter, of whom I spoke before, thought that he had disproved the existence of beta iron by proving that the A2 retardation which Professor Burgess has now demonstrated did not occur. Dr. Burgess's demonstration of the existence of. this retardation makes the existence of beta iron very probable, in my opinion. Osmond used to call beta iron " decipuum." You knew of its existence as you know of the existence of certain planets, only by the perturbation which it caused. Certain phenomena could not be explained, except by assuming the existence of a third allotropic form, beta iron. The evidence that you got was always evasive and susceptible of other explanations, except that which we have to-day, which it seems to me is not capable of other explanation. Professor Carpenter proceeded in the same way that Dr. Burgess has, by taking the heating and cooling curves of exceedingly pure iron, and thought that he had shown that there was no thermal change, no absorption or evolution of heat at the supposed A2 point, and hence that the A2 point did not exist. This he did by a piece of reasoning which I think seems to most of us rather surprising. That is to say, if of ten witnesses, three have seen a thing and seven have not, the evidence of the seven who have not is set aside, and that of the three who have seen stands. In Dr. Carpenter's own experiments under certain conditions he found the A2 change, the heat evolution., under certain others he did not. That is like the three witnesses who saw and the seven who did not see. You can arrange your test so that this change will not become visible or so that it is masked. But though an existent change can be masked a non-existent one cannot be shown. So that the reasoning seemed to me wholly fallacious.

Jan 12, 1913

By J Williams

The recent drought has highlighted the finite nature of AustraliaÆs divertible water resources. According to AustraliaÆs recently completed National Land and Water Resources Audit, development of water resources in southern Australia has reached or exceeded sustainable extraction limits. Similarly, 161 out of 538 groundwater management units are either totally allocated or already over allocated. Whilst mining only uses about three per cent of diverted water resources, water scarcity may be a major factor that determines whether potential mines can be developed in the future. Furthermore, the development of extraction and processing facilities that limit water use and maximise the re-use the waste water streams will be even more fundamental features of the mining industry in the 21st century than they are at present. There are encouraging examples where innovative water re-use technologies are significantly reducing the water used per unit of mined product. Whilst mining in the areas of Australia draining to the tropical seas may be less constrained by a current lack of water (60 per cent of divertible water resources drain into the Timor Sea, Gulf of Carpentaria and north east Coral Sea), it is highly probable that there will be increasing demand for these waters from the irrigation industry, whilst pressure will also be applied to ensure that environmental flows that benefit the coastal fishing and prawn industries are maintained. In the Great Artesian Basin, current research is demonstrating that the groundwaters are being recharged at rates considerably lower than current extraction. Whilst some other groundwater basins in arid and semi-arid Australia have currently untapped resources, these water are often relatively saline and/or may be intimately linked with key ecosystems in discharge areas. This paper presents an overview of the current state of our water resources and examines some of the key water use issues including allocation, use and reuse, environmental flows and competing demands on the resource that will ensure that water issues remain high on the policy agenda for mining, irrigation and other water users.

Jan 1, 2003

By Stephen E. Merritt, John W. Straton, T. Carl Shelton

Surveying and mapping are used to locate and visually portray objects, lines, or areas in relation to a reference point or line. The actual making of the measurements to locate the objects and points falls under surveying while mapping is concerned with putting the survey information into a graphical form. Generally, the type or class of proposed survey depends on the precision required. Some surveys may need only approximate measurements which can be obtained by simply pacing or by using an ordinary measuring tape; others may require much accuracy, thus calling for the use of an engineer's transit or theodolite along with a graduated steel tape for horizontal measurements, or a level and a graduated rod for measuring vertical distances. Mapping is likewise dependent on accuracy requirements. For example, a general layout showing the relative position of surface facilities may not call for a large scale of dimension or great precision whereas for detailed work, a large scale plus care in plotting points and drawing lines and curves are important factors. SURVEYING METHODS There are many kinds or types of surveying methods. Some examples include : land surveying for determining boundaries of land areas ; route surveying for locating roads, highways, right-of-ways, and haulways; city surveying for laying out lots, streets, and alleys; and mining surveying for projecting mine openings and locating mining operations. See Fig. 1. There are other types of surveying than those named, but in general, the type of method to be used will depend on the purpose for which the survey is to be made.

Jan 1, 1981

By Y. L. Ding, N. A. Warner

Cylindrical pellets made from graphite and chromite mixtures were reduced in high-carbon ferrochromium melts at 1 600-1 695 degrees C, under an atmosphere of almost pure CO. The reduction rate, as measured by gas evolution, increased with increasing melt temperature and graphite addition and with decreasing pellet diameter or height, although reductant particle size had a very limited effect on kinetics. At a pellet size, heat and mass transfer were significant in controlling the early stages of reduction of large pellets while at chromite grain size, gas diffusion was probably a rate-controlling step. The time required for dissolution of unfluxed pellets into the melts was significantly longer than that for reduction. This indicates that pellet dissolution may be the limiting factor in determining the operating parameters for a proposed new process to produce high-carbon ferrochromium using melt circulation

Jun 19, 1905

By M. Karmis

Subsidence planning and control must be an integral part of mine design in order to minimize the economic impact of underground mining on the surface. Pre-calculation of surface deformations which may cause damage to surface structures must be performed and dam-age criteria must be established, if the response of structures to such movements is to be determined and the extent of damages to be assessed. In this paper the Surface Deformation Prediction System (S.D.P.S.), which can be used to predict accurately the vertical and horizontal parameters of surface movements due to underground mining, is discussed. The Subsidence Response Modeling Program (S.R.M.P.). which can be applied to evaluate the response of buildings to subsidence-induced movements, is also reviewed. Finally, an example is presented demonstrating the applicability of these techniques for subsidence design and control.

Jan 1, 1990

By Onuralp Yücel, Kağan Benzeşik, Ömür Can Odabaş, Selçuk Kan

Extraction and processing constitute an important area in the metallurgy of molybdenum. Molybdenum trioxide (MoO3) production is one of the most important stages in molybdenum production. In this study, the effects of different furnace types on MoO3 production were investigated by using molybdenum concentrate as a raw material obtained during the enrichment of copper ores. Preliminary experiments have been made using a chamber type furnace, and a transition to a pilot-scale has been carried out with rotary kiln experiments. The effects of a different time and atmospheric conditions on MoO3 roasting kinetics were investigated by experimental studies conducted in the temperature range of 500–650°C. It was determined that the optimum temperature and time for sulfur (S) removal was 625°C and 180 min in the studies carried out in the rotary kiln, and it was determined that 0.61%S content was reached with an average removal efficiency of 98%. The activation energy in these sets was calculated as 89.519 kJ/mol.

May 3, 2021

By G. P. Conard, E. H. Rennhack

The creep behavior of hot-rolled, hypoeutectic Zn-Ti alloys was investigated in the temperature range from 0.43 to 0.53 TM. Secondary flow was found to originate primarily from strain-induced gvain growth where grain boundary )nigvation served to relieve the strain energy of distortion introduced by slip, grain boundary sliding, and subgvain formation. The extent to which this recovery mechanism operated was determined by the ratio of grain width to the spacing between planar fibers of TiZn,, compound particles generated in these alloys during rolling. When this ratio was unity, creep resistance demonstrated a marked improvement. In this condition, which was fulfilled by annealing following rolling, structural stability was enhanced with decreasing grain size below the equicohesive temperature (-0.5Tm), while the reverse was true above this temperature. TITANIUM concentrations approaching the eutectic composition of 0.23 wt pctl have been shown to promote a significant increase in the creep resistance of rolled zinc,2 The alloying effect created with titanium is somewhat unique; a structure closely resembling that of a fiber-reinforced metal composite can be developed which selectively modifies creep strength in preference to other mechanical properties. In an earlier investigation,~ the present authors found that, while the fiber network, composed of individual TiZn,, compound particles, had a distinct influence on rolled texture, the crystallographic variations produced were of minor importance with respect to creep. Rather, creep resistance seemingly increased when the grain size appeared to coincide with the in-terfiber spacing. The work described here was undertaken to explore this effect in greater detail. EXPERIMENTAL PROCEDURE Three zinc-base alloys containing 0.05, 0.12, and 0.16 wt pct Ti were prepared from CP zinc and iodide titanium in the form of 4 by 2 by f in. chill-cast ingots. The melting and casting procedures for these alloys have been detailed el~ewhere.~ Individual ingots of each alloy were hot-rolled at 200°C (392°F) to total reductions of 10, 25, 50, 75, and 90 pct in from one to five passes, respectively, employing a 10-min reheat prior to each rolling pass. With grain, tensile-type creep specimens with a 1-in.-long, -in.-wide gage section were machined from the rolled strips for test purposes. Annealing studies to explore the influence of grain size on secondary creep flow were carried out at 400°C (752°F) in argon for times extending up to 60 min. The grain-size effect was evaluated in terms of average grain width and length values statistically derived from lineal intersection measurements.4 A similar method was applied in establishing the average interfiber spacing, i.e., average perpendicular distance between adjacent planar fibers. The creep characteristics of the alloys were investigated by means of constant-load and constant-stress creep tests. The former tests were conducted at 25°C (77°F) under an initial stress of 10,000 psi, while the latter were performed in the range from 25°C (77°F) to 90°C (194°F) at stress levels varying from 8000 to 22,000 psi. Total specimen strain, as determined with Budd HE-1161-B strain gages, was in excess of 0.10. Maintenance of constant stress was achieved through periodic load reductions made at 0.01 strain intervals to compensate for the attendant incremental reduction in specimen cross-sectional area. The maximum indicated error in the applied stress at these strain intervals was less than 3.0 pct. RESULTS AND DISCUSSION Constant-Load Creep. In an effort to clarify the in-terrelation between interfiber spacing and grain size with respect to the creep resistance of the Zn-Ti alloys, their separate effects on secondary creep rate were determined as a function of titanium content and rolling reduction. These results are set forth in Figs. 1 and 2, respectively. The average grain diameter plotted in Fig. 2 was resolved from average grain width and length values. No data are presented for reductions of less than 50 pct because of the inability to obtain consistent measurements on these strips. The curves of Fig. 1 indicated that, for a given titanium content, a decrease in interfiber spacing, as produced with increasing reduction, promoted a decrease in creep rate. Depending on titanium content, however, wide variations in creep rate occurred at the same interfiber spacing suggesting that interfiber spacing, by itself, has little or no influence on creep resistance. Grain size, on the other hand, decreased progressively with both increasing rolling reduction and titanium content, the effect of which led to a pronounced decrease in creep rate, particularly when the average grain diameter became smaller than 3.0 x 10"4 in., Fig. 2. The continuity of this relationship tended to support the view that grain size rather than interfiber spacing was predominant in controlling secondary creep. Annealing Effect. The observed dependence of creep flow on grain size suggested that a further contribution to creep resistance would result when the alloys were annealed to effect a coincidence between grain width and interfiber spacing, see Fig. 3(b). ~eiides creating an immediate barrier to grain boundary movement, annealing offered the possibility of providing increased structural stability by eliminating many high-energy, mobile grain boundaries.= To test this hypothesis, specimens from the Zn-0.16 Ti strips reduced 75 and

Jan 1, 1967

By James E. Lawver, James L. Wright

This paper describes the design of a cell used to measure the electrical conductivity, or the reciprocal resistivity, of granular materials. It also establishes a quantitative relationship between the electrical conductivity and the electrical separation of selected mineral samples. It is estimated' that the free world produces about 13 million tons of mineral concentrates a year by electrostatic or electrodynamic methods. At least 95% of these concentrates are produced by corona discharge type machines that separate minerals by exploiting the differences in their electrical conductivity. But, what is meant by the electrical conductivity of a mineral? How large a difference in the electrical conductivity of two mineral species is necessary to effect a separation? Just what is the role of conductivity in electrical separations with regard to capacity and selectivity? There is a considerable amount of information in the literature on both the mechanisms of conduction and the values of the electrical conductivity of pure single-crystal mineral specimens. In addition, some insight into the role of mineral conductivity can be obtained by referring to a Bureau of Mines publication' in which 95 minerals have been grouped as conductors or insulators as a function of temperature. The classification was made on the basis of the percent of weight that reported as "conductors" in an electrical separator. But, as is often the case in the mineral industry, practical application leads theory — and there is little useful information in the literature giving any kind of quantitative relationship between electrical conductivity and electrical separations. The problem is a bit complex because electrical conductivity per se — which can be rather easily measured on large, single grains — is not sufficiently informative to permit quantitative predictions of the separability of the mineral system. Practical "high-tension"* separations are made at such feed rates that the band of minerals on the rotor is multilayered in thickness. Thus, the effective conductivities of minerals as seen by a high-tension machine include particle-to-particle contact resistance, which is often a controlling factor in making a separation. This is particularly true when the mineral grains are coated with slime or with a dielectric surface film. From a high-tension separation viewpoint, one is actually concerned with the time required for corona-charged grains to lose enough charge so that the centrifugal force acting on the particles exceeds the image force holding the grains to the rotor. This calculation requires a knowledge of the effective mineral conductivity s. (The conductivity of the metal rotor is sufficiently greater than that of the minerals so that it need not be considered in charge decay calculations.) The charge density at time t can be approximated by the relaxation equation.3 where t 5 charge density at time t r, - charge density when t = 0 cr e total electrical conductivity £ = permittivity The time required for the charge density to fall to l/e of its initial value is called the relaxation time and is numerically equal to €/n. AS defined here, u is the conductivity of an element of homogeneous grains making contact with each other and with a grounded rotor. This paper deals with the design of a conductivity cell used to measure a, or its reciprocal p, the electrical resistivity. CELL DESIGN Initial test work was performed with a cell recommended by ASTM.4 Since the reproducibility with the ASTM cell was not satisfactory, it was decided to

Jan 1, 1970

By C. A. Rowland

When studying the feasibility of using autogenous or semi-autogenous grinding, operating and engineering companies frequently request assistance from the mill manufacturers in three areas - 1. Recommendations for studying the suitability of autogenous or semi-autogenous grinding for the specific ore. 2. Mill sizing, to accomplish required grind. 3. Recommendations on mill design and operation. Rod mills and ball mills are selected by the use of bench scale standard grindability tests and established calculation procedures, of which the most frequently used are the Bond Grindability tests and the Bond Work Index equation(1). The accuracy of these have been reviewed by C. A. Rowland in his papers, showing the correlation of work indices calculated from plant operating data and laboratory grindability tests(2)(3). The selection of autogenous and semi-autogenous primary mills has not reached the stage where mill size selection can be made from bench scale tests. Considerably more extensive testing will be necessary than required for selecting rod mills and ball mills.

Jan 1, 1974

The hydraulic backfilling of mine tailings has proven very successful at the Homestake Mine in Lead, South Dakota. It allows greater versatility, selectivity and safety in mining. It has also minimized surface subsidence and underground rock movement. The tight filling also eliminates underground fires. This paper explains the hydraulic backfill method used and the problems encountered by so doing.

Jan 1, 1973

By F. T. Cawood

This article offers a personal and independent view on the threats to the sustainability of the South African minerals industry. It argues that if the six identified threats of insufficient spending on research and development, general standard of education, nationalization, inadequate infrastructure, Aids prevalence and labour inefficiency are not acted upon as a matter of urgency, the future of the mining industry, along with its important contribution to the economy, is at risk.

Jan 1, 2011

By D. E. Macdonald

"Approximately 2.0 million tonnes of phosphate rock is imported from the U.S. to Alberta annually and is used in the production of agricultural fertilizers. No phosphate rock is presently mined in Canada, although sources of igneous phosphate have been mined in the past. Sedimentary phosphate rock is found in nine geological units within the Cordilleran Foothills and Front Ranges region of Alberta. The Devonian-Mississippian Exshaw Formation, Permo-Pennsylvanian Rocky Mountain Supergroup, and the Jurassic Fernie Formation have the best potential f or future development. Most of the phosphate rock in Alberta is of low grade and lies within restricted land use areas. The best over-all resource potential lies in the Fernie basin area of southeastern British Columbia, in the Fernie Formation. The possibility of deep phosphate rock deposits in the plains region should be examined.Phosphate rock is mined in Idaho, Utah, Montana and Florida, and is shipped to Canadian fertilizer plants for processing. Raw phosphate rock is acidified, usually with sulphuric acid, by a wet process. Varying amounts of ammonia are added, and the fertilizer is pelletized. Future research, in western Canada, is needed in the beneficiating of low-grade ores and in the area of in situ mining. At the present time, phosphate rock sells for around US$50Itonne, and Alberta fertilizer companies probably pay in the range of C$7D-$85Itonne for U.S. phosphate rock delivered to the plant. Environmental concerns about phosphate rock processing are centred around gypsum tailing ponds, and radioactive wastes.U.S. supplies of phosphate rock are secure until the year 2000; however, by this time, the richer deposits in the U.S. may be exhausted. Alternate deposits, such as the ones in Alberta and British Columbia, might then be considered. Phosphate byproducts, such as uranium, vanadium, fluorine and rare earth elements, may help in making the processing of low-grade Canadian phosphates economically feasible."

Jan 1, 1988

By Jack Parker

There are some simple theoretical approaches to pillar design but they leave much to be desired. There are also more complex theoretical approaches, but at this time the most realistic approach is to go into the mines and observe and measure how real pillars are performing under real conditions; to allow the information thus gathered to ferment in our minds - then to project the behaviour of those pillars into our new designs and mining techniques, probably with no formulas at all. Examples, from half-a-dozen different mines, show how a simple- minded approach, through observation and measurement, led to changes in pillar design which often contradicted the textbook but made very significant contributions to mining safety, efficiency and costs. The good news is that we know a lot more about pillar design than we realize. We have, between us, looked at millions of pillars of all kinds, under all conditions, but we have overlooked what they are trying to tell us. We can take problem situations and turn them into opportunities and, in that way, become better stewards of the resources which have been given to us.

Jan 1, 1983