Search Documents

Alluvial gold exploration is aimed at recognizing areas of anomalous gold content as evidenced by the nature of the drainage system, its age, geomorphic history and other features of the geological environment including the provenances. Subsequent studies to quantify the findings are governed by the need for accurate data based upon precise measurements. Computerization allows the use of more complicated mathematical procedures than are feasible manually, thus promoting the development of more advanced technological aids. Data banks provide the means of storing vast quantities of information for instant recall.Sample representivity is a major problem and a clear understanding of both sampling and analytical requirements is essential for dealing with problems arising from variations in sample size and particle size distribution. Field samples must always be large enough to ensure adequate representivity or the sampling has failed in its purpose.

Jan 1, 1984

By Wilber Duvall, Leonard Obert

"INTRODUCTION This report is the first of four to be presented on the microseismic method 4/ of predicting rock failure in underground mining. The application of the microseismic method to one specific case, namely, that of predicting rock bursts in deep mining, has been described in two previous reports. 5/ 6/ Since the publication of these reports 5/ 6/ the method has been extended to other fields of mining, end it is the purpose of this report (Part I) to describe the general microseismic method, giving the empirical facts upon it is based, the different testing procedures, the method of recording and analzing the data, and the interpretations that can be obtained there-from. Part II will describe a series of laboratory experiments that were performed to give information on the origin of microceismims and the microseismic properties of various rocks. Part III will cover application of the method to specific mining problems together with a brief description of a number of investigations performed during, the last three years. Part IV will describe in detail the microseicmic equipment used in the various phases of these investigations."

Feb 1, 1945

By Lyman File

This paper discusses the overall challenges to construct a two-lane highway tunnel located in southwestern Colorado on U.S. Highway 160 for the Colorado Department of Transportation by the Kiewit Western Company. The purpose of this project is to provide the excavation and temporary support for a highway tunnel 280 m (916 feet) long. The tunnel cross section is 14.3 m (47 feet) wide by 8.5 m (28 feet) high, 105 m2 (1,130 SF).Construction methods include conventional drill and blast excavation with rockbolt and shotcrete ground support. This unique tunnel is being constructed under alpine tunnelling conditions and in the immediate vicinity of active highway traffic.

Jan 1, 2003

Myuna Colliery long term ventilation requirements were included as part of the overall planning of colliery construction and underground development. Ventilation, during the simultaneous sinking of two drifts and the downcast shaft, was accomplished by established methods of ducted exhaust and blower fans. Drivages for the 3 seam interconnections of shaft and drifts were ventilated by extension and duplication of the exhaust systems. Ventilation, for the below seam extension of the belt drift, construction of between seam and below seam bins, and the completion of a circular between seam drift, required a step by step changeover to a temporary main ventilation exhaust fan mounted adjacent to the top of the completed downcast shaft. The second, permanent upcast, shaft was commenced and colliery production started one seam at a time, using the transport drift, while the underground bins, belt and between seam drifts were completed. The uocast shaft was completed and a connection made in the upper seam, completing all contract mining and allowing the main fan to be erected. The permenent twin centrifugal fan system was installed, commissioned and test run to

Jan 1, 1983

By M. J. Hannan

Considerable interest has arisen in developing analytical methods suitable for measuring resource commodity substitution patterns. some of this work has applied the Translog method to estimate actual elasticities of substitution. Recent examples incl.uae Privolos and Dunietz (1987), Kopp and Smith (1983), and Moroney and Trapani (1983). Another method, one which has received attention earlier in the work of Fisher and Pry (1970), is that of the logistic or diffusion function. We believe that the latter method has properties suitable for analyzing current problems of material substitution. The present study thus evaluates this method in its original logistic form as well as an extended version incorporating additional explanatory influences. The analysis is applied to copper/aluminum substitution and iron ore beneficiation. Substitution for copper by aluminum is examined in the building wire and cable, and magnet wire end-use markets. For iron ore, the substitution of pellets for sinter is considered for the U. S. market.

Jan 1, 1990

By Ronald W. Utley

INTRODUCTION The ''Do's and Don'ts" of installing equipment in a comminution circuit begin during the study stage of a proposed project, continue through preliminary engineering, detail engineering, procurement, the actual placement of equipment at the job site, and end with turnover to the owner. Equipment supplied for a modern comminution circuit will be high quality, rugged machinery designed according to appropriate manufacturing standards for long hours of trouble-free service. However, certain precautions and procedures must be observed in plant design and layout, equipment handling, installing and servicing in order to obtain optimum performance. This chapter contains general installation "DO'S and Don'ts" for the major equipment in the circuit. •Primary Gyratory Crushers •Rock Breakers (Hammer) •Belt Conveyors •Apron Feeders •Weigh Belt Scales •Secondary Crushers •Vibrating Screens •Grinding Mills •Mill Liners •Open Gear Sets •Speed Reducers •Electric Motors •Cyclones •Slurry Pumps Some questions will not be covered in this chapter, or may not be applicable to the actual equipment purchased, as requirements do vary from manufacturer to manufacturer. Additional specific information can be obtained by contacting the manufacturer's local representative or the factory. All inquiries should be accompanied by the following information: •Unit size and type of equipment •Manufacturer's shop order number (after order placement) •Serial number (after manufacture) DO'S 8 DON'TS FOR INSTALLATION OF ALL COMMINUTION CIRCUIT EQUIPMENT Installation By Design DO obtain tables of weights and clearances from manufacturer. DO obtain WR2 forces from manufacturer to determine that the foundation is adequate. DO determine compression strength of foundation soil and/or rock. DO obtain manufacturer's recommended typical foundation drawings. If substantial alteration to manufacturer's drawings is required, check with the manufacturer before proceeding.

Jan 1, 1982

By Alan J. Wianwright

Introduction ??New world-class Upper Devonian porphyry Cu-Au system located in south Mongolia ??6.5 km NNE-trending mineralized corridor ? 4 discrete deposits ??Southern Oyu deposits: Chalcopyrite, deposits: bornite ??Hugo Dummett: Zone: Hypogene chalcocite in addition to chalcopyrite and bornite ??Total resource exceeds ~2 Gt@ >1% Cu, >0.25 g/t Au (0.6% Cu equivalent cut-off) (Ivanhoe Mines press release, 2005)

May 1, 2006

By Almon F. Robertson

"INTRODUCTION At various times, North Carolina has supplied small quantities of brown-iron ore to the furnace o the South. Between 1917 and 1920, the quantity reported to the Federal Geological Survey was 126,000 tons. Most of this came from Cherokee County. 3/In furtherance of the program initiated by the Bureau of Mines to develop additional reserve of iron ore during the emergency, the Cherokee County deposits were examined by an engineer 4/ of the Bureau of Mines, and work was recommended on,12 properties.The project was begun in April 1944 and continued intermittently until April 1945, when work was stopped. During this period, eight properties were explored, and an additional property was mapped.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch; Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

By R. T. C. Rasmussen

"INTRODUCTION This is the second report of investigations describing tests in full-scale commercial heats of steel-using electrolytic manganese having a purity of about 99.95 percent, produced in the Bureau's pilot plant at Boulder City, Nev. The first report dealt with tests in cooperation with two companies can the use,of electrolytic manganese in the manufacture of stainless steel. 3/ Plans aril cost estimates for reasonably large commercial, electrolytic plants based upon pilot-plant experience, as well as the comments of a number of concerns where electrolytic manganese has been tried, are contained in another publication.4/ The tests in cooperation with industry are part of the Bureau of Mines program of investigations of methods of utilizing low-grade domestic manganese ores, thereby the United States leas dependent upon foreign sources of manganese for metallurgical use. The Boulder City pilot plant already has demonstrated the feasibility of producing electrolytic manganese from several of the most important reserves of low-grade manganese ore. As the ferromanganese normally used by the steel industry represents the bulk of the Nation's manganese requirements, the usefulness and possi¬ble advantages of electrolytic manganese in the manufacture of steel must be established if electrowinning from domestic ores is to become an important factor of manganese supply.Preliminary arrangements for the cooperative tests at the Atlas Steel Casting Co., Buffalo,. N. Y., were made with E. L. Altenburg, vice president and general manager of the company, by A. A. Dow. 5/ The data on the tests at the Atlas plant presented herein are based upon reports of E. L. Altenburg and information obtained by the author during a visit to the plant to observe the initial trial heats with electrolytic manganese in the open-hearth and the electric furnace."

Nov 1, 1945

By G. R. FITT, S. R. B. Cooke, C. W. Davis, V. H. Gottschalk, C. G. Maier, C. E. Wood, R. S. Dean, S. B. THOMAS, John Gross, E. P. Barrett, T. L. Joseph

Lack of funds has prevented publication of much of the metallurgical work of the Bureau of Mines during the past 2 years . The present progress report covers studies in the direct production of iron and steel . The experimental work was carried out in cooperation with the universities of California , Minnesota , and Missouri . Complete reports will be published when funds are available .

May 1, 1934

By Whiten WJ

Although cone classifiers have received little attention in the modelling of mineral processing units they are one of the oldest non-mechanical classifiers. Their use has enjoyed a revival in recent years because of their low cost of installation and operation. In this paper the development of models for cone classifiers is reviewed and a new model is proposed. The experimental work, data collection and analysis are briefly described, and the new model is presented and discussed. The data used in the model development are made up from three distinct experiments using different units in each case. There are 21 data sets from a 3 m cone treating the tailings in a copper concentrator, 24 data sets from a 0.3 m pilot-scale cone, and 29 data sets from a laboratory glass funnel (0.(Y73 m diameter) used as a cone classifier, giving a total of 74 data sets. The model structure was developed from an analysis of particle settling in classifiers, using specialised model building software. The size of a particle settling in a separator and the forced flow through the apex of the cone were related via hydrodynamic dimensionless groups to the operating conditions of the unit. The model predicts the separation efficiency using the following four parameters: efficiency curve shape factor, cut-point, underflow density (per cent solids) or underflow pulp velocity. The model covers a range of feed flowrates from 1.2 to 5000 1/min.

Jan 1, 1993

The Golden Valley Volcanic Centre has been recently interpreted as being a combination diatreme breccia pipe and rhyo-dacite flow dome complex of Permo-Carboniferous age that intrudes basement granitoids and sediments of Ordovician-Devonian age. Exceptionally good exposure at the Centre has enabled the relationships between different lithologies to be determined. This, along with petrological studies, has led to a detailed understanding of the geological environment in which the complex formed. Gold, silver and base metal mineralisation have been recently shown to be associated with the Marginal Breccia at the perimeter of the diatreme. Comparisons have been made between the geology and mineralisation in this system and several similar diatremes which also contain gold-base metal sulphide mineralisation.

Jan 1, 1990

By Smith I. W

Australia has, and faces, a growing problem with regard to the ability to meet the demand for liquid fuels from indigenous petroleum resources. The position for natural gas is better but there is no room for complacency. Since the coal resources are relatively extensive, interest in the prospect of producing liquid fuels from coal is in- creasing. The approaches to the production of gaseous and liquid fuels are briefly reviewed and the present status of coal conversion technology is discussed. Many problems remain to be solved and it is estimated (in the USA) that another 8-10 years will be required before any of the processes for liquid fuel production are considered sufficiently efficient and viable to go to a demonstration plant. Coals represent complex feedstocks and the effects of variations in coal properties on oil-from-coal processes are not fully understood. The thermal efficiencies of various coal conversion processes are considered in relation to their impact on coal requirements. The production of Australia's present requirement for liquid fuels by the only commercial process in operation would require a four-fold expansion in the local consumption of coal. Any assessment of the suitability of oil-from-coal processes currently under development overseas for Austra- lian coals and requirements must take heed of the differences in coal properties and motivation. The economic via- bility of processes for producing oil from coal will continue to be uncertain because of the large difference between the World price for crude oil and the actual production cost.

Jan 1, 1975

By W. K. Muwais, R. G. Cuddy

"The Lower Cretaceous McMurray Formation contains the bitumen reserves of the Syncrude Mine in northeastern Alberta. This formation comprises sediments deposited sequentially in fluvial, estuarine and marine depositional environments. The Syncrude Base Mine area consists mostly of estuarine sediments, as much of the original marine sediments have been eroded away. These estuarine deposits consist of channel-fill sediments and interchannel tidal flat sediments with the channel-fills comprising most of the orebody.Channel-fills contain, among other lithologies, interbedded sand, silt and clay rich layers that often occur as sequences of inclined beds with dips up to 25 degrees or more. A detailed knowledge of the distribution of these inclined beds, their lithological characteristics and their continuity is very important in assessing the risk of mine highwall instability . Techniques used to identify and characterize adverse structures are reviewed. INTRODUCTIONGeneralThe Syncrude Canada Ltd. oil sand mine is located within the surface mineable portion of the Athabasca Oil Sands area about 40 kilometres north of Fort McMurray in northeastern Alberta, Canada (Fig. I). The company commenced large-scale strip mining of oil sands in June 1977in the area, referred to as the Base Mine, situated in the southeast corner of the company's two lease areas (Fig. 2).The mining method (Fig. 3) utilizes large electric drag lines operating on a single bench with highwall depths up to 60 metres. Feed grade oil sand (= 6 wt.% bitumen) is mined by draglines and windrowed parallel to the highwall crest. Lower grade oil sand « 6 wt. 0J0 bitumen) occurring as waste bands is selectively mined by the draglines and cast back into the mined out pit or placed on the bench and hauled by truck. The windrowed feed is delivered to the extraction plant by a bucket wheel reclaimer and conveyor system. Stripping of Recent, Pleistocene and Cretaceous overburden units is done outside the conveyor systems by mobile equipment. The 4.5 kilometre long mine is split into four quadrants for planning and scheduling purposes, with each quadrant having an individual dragline-bucketwheel-conveyor system.Surface mining of oil sand at Syncrude requires the removal of vast quantites of material. The design of the open pit mine relies heavily on knowledge of the distribution of ore and waste materials, and on the physical characteristics of these materials.The geology of the oil sand below the dragline bench at the Syncrude Mine is complex. Geological, geotechnical and hydrogeological factors play an important role in the design and operation of the mine. This paper describes aspects of the geology that impact on the design and operation of the mine. Some of the methods and procedures adopted by Syncrude to successfully overcome difficulties that the complex geology creates are discussed."

Jan 1, 1989

By G. E. Goodspeed

THE Cornucopia gold quartz veins form a parallel vein system traversing metamorphic and granodioritic rocks. Field and petrographic evidence suggests that metasomatism has played an important role both in the emplacement of the granodiorite and in the formation of the veins. Structurally the veins appear to be related to the major tectonic features of the Wallowa Mountains and to be narrow shear zones rather than filled fissures. Petrographic studies indicate a complex history of formation starting from initial alteration along fractures or joints followed by recurrent fracturing and a quartz-forming stage, and closing with continued shearing and microbrecciation, which permitted the upward percolation of the later ore- forming solutions. The precipitation of ore minerals from these solutions formed ore shoots. Postmineral effects include the injection of Tertiary basaltic dikes, a slight amount of cross faulting, and some movement along the planes of the veins as well as oxidation.

Jan 1, 1939

By Williams RC

Overlying the coal deposits of the Sydney Basin are several lakes and other bodies of water. These include the Pacific Ocean, Lake Macquarie, the Tuggerah Lakes and the stored waters of the dams of the New South Wales Metropolitan Water Sewerage and Drainage Board. The coal beneath these bodies of water amounts to hundreds of millions of tons. Colliery workings have approached these areas of water and in some instances first 1"orkings of bord and pillar have taken place oi_eshh the water. he problem which now faces mine manage- and other interested authorities involves the determination of the maximum ;mount of coal which can be safely extracted from beneath the water. There are many factors to be considered including the depth of cover, seam thickness, geological details and strata movements.

Jan 1, 1972

By Johann van Wjk

Mandatory Codes of Practice to Combat Rock Fall Accidents came into force on South African Collieries in 1997. These were drawn up in accordance with guidelines issued by the Chief Inspector of Mines, The Codes of Practice (CoP's) are legal documents in terms of the South African Mine Health and Safety Act 1996. One of the main results Of the introduction of the COP'S from a practitioner's point of view is that they formalized much of what would have constituted a typical visit to an underground section previously. Other important requirements were as Billows: Support rules and Strata Control Standard Procedures were to be drawn tip. Identification of Special Areas (areas requiring a higher level of rock engineering input and with, typically, higher order of support and restrictions on mining geometries), Changing conditions underground to he identified timeously. Implementation of the CoP to he monitored. To comply with these requirements on Ingwe Collieries (a division of BHPO Billiton Energy Coal) it was decided to produce too separate forms to be used in conjunction with each other. The first of these, the "Underground Section Physical Risk Rating" measures the physical conditions in each section whereas the second form, the "Section Perfomance Rating" determines how well the section personnel are Coping with the conditions. This form also pleasures compliance with the Support Rules and Strata Control Standards. Both forms are essentially risk matrices but with various scenarios described, each with a certain weighting. The "Risk and Performance Form" system for bord and pillar operations has by now been used for five years in the Ingwe and Eyesizwe Mining Collieries and has achieved a great deal of acceptance. This system has enabled the quantification of previously subjective observations and has improved the strata control awareness and management of underground mining sections. Amongst other initiatives it has assisted ill reducing the severity and frequency of fall of-ground accidents.

Jan 1, 2002

By Charles H. Parr

A testing program was conducted to determine the suitability and reliability of adhesives and polycarbonate lenses for extended use in luminaires in mine environments. Polycarbonates were exposed, for periods up to 36 months, to four environments including ultraviolet light, humidity, intermittent water spray, and heat of either 180°F or 407 in various combinations. Rod impact tests on the exposed lens material indicated, that polycarbonate functions well under all 180°F environments and could be used with confidence for periods exceeding the test period, for as long as ten years, with a suit) able safety factor employed in design. The specimens exposed at 240°F showed decreased toughness after 24 months' exposure. Extrapolation of these data was deemed to be risky. A 462-day compatibility test between polycarbonate and six hydraulic fluids was run on stressed PC beams. One fluid caused beam breakage in less than one day, while three caused breakage at intermediate times. Two fluids exhibited essentially no effect on the PC when compared to a control. Epoxy and silicone adhesives were tested as lens adhesives and sealants. Three epoxy combinations tested showed low and erratic failure stresses. A room-temperature-cure silicone adhesive functioned extremely well for time periods up to 36 months and temperatures u2 to 240°F.

Jan 1, 1985

The changing characteristics of raw materials has highlighted the limitations that conventional vibrating screens have in the handling of fine wet sticky materials. These' limitations have led to the development of a totally new concept of screening, the Rotating Probability Screen. In order to illustrate the practical benefits to be gained by the extraction of fine materials ahead of subse quent processes particularly in the coal industry, the experiences gained in Ro-Pro installations in America, Australia, Europe and Britain are drawn upon.

Jan 1, 1984

By Waldemar Lindgren

Jan 1, 1905