Search Documents

By H. A. Bedworth, W. H. Bassett

The amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors' laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hampe1 that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe's method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen. Heath4 found that the loss in weight after heating in hydrogen did not represent the true oxygen as cuprous oxide but included also gases derived by the metal from the fuel and refining in the furnace, and any trace of mechanically held moisture. He found, further, that the copper after ignition retained hydrogen equivalent to about 0.01 per cent. Heath proposed to determine the amount of occluded gases by preliminary ignition for 20 min. in pure carbon dioxide—and to correct the error caused by absorbed hydrogen by subsequent ignition and cooling in carbon dioxide, finally replacing this gas with air.

Jan 1, 1926

By John S. Wakeman

The progress results of a pilot plant study on the effects of ball top size and other mill operating parameters are reported. Test series on taconite and quartzite crude ores using a 1.7m diameter primary mill in closed circuit with a vibrating screen indicate clear trends on the improvements of mill throughput and power consumption when using larger diameter balls. Possible effects on mill liner and ball consumption as well as future research plans are discussed.

Jan 1, 1984

By N. Arbiter

The theoretical analysis of tumbling mill energetics and performance has largely neglected mill dimensionality, and, in particular, the importance of the length/diameter ratio. This is in spite of the fact that practice varies substantially in this area: geographically, for semi-autogenous and autogenous mills, as between North America and South Africa/Scandinavia; historically, for overflow ball mills, for which the L/D ratio has increased significantly from the earliest small mills to/the largest mills currently. The present study is concerned primarily with the influence of the L/D ratio on the design and operation of overflow ball mills; on the occurrence of the overload phenomenon; and on the limits, if any, it may impose on mill capacities because of critical pulp axial velocity limits. It will be shown that the shape face or is of major importance in this area; and that its adjustment to the extent that this is practical should remove the diameter limitations previously postulated for this mill type.

Jan 1, 1990

All large open pits in Australia have been mined, or are planned to be mined well below the local water table. This raises several issues that impact on mine safety, mining costs and regulatory approvals. Some pits will be æwetÆ, where they are mined through permeable horizons and where there will be measurable groundwater inflows. These will require some form of dewatering. There may also be some difficulties in the disposal of excess water. Other pits, may be ædryÆ, where they are mined through impermeable material and there are no measurable groundwater inflows but where there are stability issues related to hydrostatic pressures within the pit walls. These may require some form of depressurisation. Some pits are a combination of both. Effective management of groundwater inflows and groundwater related stability issues and the development of cost effective and environmentally acceptable dewatering and depressurisation systems requires an understanding of site specific hydrogeological conditions and practical experience in what works best for different conditions. The presentation will include an outline of the key hydrogeological factors that impact on large pits, practical methodologies for achieving dewatering/ depressurisation, and some case studies from the Goldfields, Pilbara and North Queensland.

Jan 1, 2003

By I. Tinto

"IntroductionEnvironmental pollution problems, caused by gases or effluents, by high noise levels or from air borne dust, are placing increasing demands of the operators, from statutory authorities, and from the general public, to adopt more stringent dust control measures. This requires that a successful plant dust control program be an integral part of any plant operation. While a successful environmental program is a key factor in maintaining productivity and good labour relations, anticipation of future environmental regulations during the plant design phase can avoid the high cost of plant upgrading, or dealing with pulmonary conditions in the work force in subsequent years.Particulate removal, conventionally called dust collection, involves the removal of coarse- and fine-particulates from the airstream. Although generally limited to that required for contro!Hng plant generated air emissions, particulate control equipment also has a wide application for air cleaning and filtration inside the plant, as well as for recovery of usable products.In the late 1950s and early 1960s the public became more concerned with the problems of air pollution. This increasing concern was stirred by an awareness of the extremes to which water pollution had progressed in many of the rivers and lakes, by increasing perception of air pollution as detected by visible smog and harsh chemical odors, by the alarming rate of increase of smog plagued cities and communities, and by specific incidents where ill health could be traced to specific episodes of air pollution. Particle size is perhaps the most important single factor affecting particulate control. Large particles (over 5 microns) constitute the major mass fraction of most sources of emission and economical control equipment dqes exist for their efficient control. However, while these larger particles frequently represent the source of soiling and unsightly smoke plumes, they are not a major health problem as they tend to settle relatively quickly, are more easily scrubbed from the atmosphere by rain, and are not able to penetrate the respiratory system. By far the most important form of particulate air pollution is the fine particulate, (below 3 microns) which is harmful to the pulmonary system. The adverse effects caused by this particulate matter on human health are for the most part related to injury to the surfaces of the respiratory system. Particulate material in the respiratory tract may produce injury itself, or it may act in conjunction with gases, altering their sites or their modes of action. A combination of particulates and gases may produce an effect that is greater than the sum of the effects caused by either individually (i.e. synergistic effect)."

Jan 1, 1989

By Ho D, Yang J

The ready availability of powerful desktop workstations, which combine 3D real-time graphics and processing speed better than that of supercomputers of a few years ago, now allows the cost-effective solution of real world geomechanics and underground mining strength simulations. The inclusion of geotechnical factors such as rock joints and porous flow on strength and stability are discussed together with the range of available deformation and failure models for soil, rock and concrete. This paper describes the capabilities provided by finite element graphics and analysis software for modelling and sequential investigation of both excavation and lining, or rock bolting, construction sequences. Examples of the use of finite element models in mining are also included in the paper, together with a discussion of the required people, software and computer hardware resources required to achieve timely and productive results.

Jan 1, 1995

By C. S. Barrett, P. Coheur

ANNEALING twins are common in the microstructure of copper that has been rolled and recrystallized. In such samples it follows that a twin relationship should exist between components of the recrystallization texture,1 and several examples of this have been reported. For example, twin relationships have been found in recrystallized electrolytic copper sheet, as indicated in Fig. I, from a paper by Coheur and Lejeune.2 In this pole figure the cube texture (100) [001] is indicated by the hollow squares in the lower half of the figure (the pole figure for 200 reflections) and in the upper, (111), part of the figure. The texture contains, in addition to this orientation, the first-order twins of it, shown in the figure by the filled triangles. This orientation relation has been suggested by others also, under certain annealing conditions,3,4 although pole figures have not been published to confirm it. Some orientations in recrystallized sheets are identical with their twins, because of the symmetry elements of the texture this is true, for example, with the (113) [211] texture so commonly reported for brass-hence it appears impossible in such samples to decide whether the twin relationships result from twinning or merely from the symmetry of the deformation process. The present investigation of a commercial copper strip seems to yield an example in which annealing twins account unambiguously for the principal orientations present. It proves to be a case, also, for which the recrystallization texture cannot be viewed as derived from the deformation texture by a first or second-order twinning mechanism . MATERIALS AND METHODS The samples investigated were of secondary copper (melted in Belgium) to which 0.19 per cent iron had been added to raise the recrystallization temperature. How much the orientation characteristics of this metal can be ascribed to the iron content and how much to other impurities or to melting and pouring practice has not been investigated.* The rolling was done in one direction only, on a mill with rolls of about 20-cm diameter. A strip 10 cm wide was reduced from 5 mm thickness to 0.05 mm by several cold passes at commercial speeds. The samples cut from this 99 per cent reduced strip were X-rayed throughout their entire thickness. A pole figure made soon after rolling and annealing was identical, within experimental error, with one that was made when a two-year interval occurred between rolling and annealing. X-ray patterns were made on a cameral that traversed

Jan 1, 1946

By Rao Pothini

Measurement of pressure distribution under the base plate of the Hemscheidt 2-leg 800-ton shield was performed underground for two shifts using 12 pressure cells installed in two rows, one each under each split base plate. Pressure distribution was uneven depending on contact condition. In general the highest base pressure occurred at 1/3 of the base plate contact length from the rear edge. The resultant was near vertical, and the pressure under the tail side split base plate was always higher than the head side. For comparison, pressure distribution on the canopy and under the base plate was also measured under controlled conditions at the USBM's Mine Simulator Testing Facilities in Pittsburgh, PA. A total of 45 tests were conducted under several simulated contact conditions. The results showed that the actual contact area is highly dependent on the compliance of the immediate roof and floor due to the sloped canopy tip and a base lifting device under the base tip. The loading distribution tends to change in magnitude and profile as the leg pressure increases. The base lifting device exaggerates the high toe loading on the base plate characteristics of this type of shield support. This paper describes in detail the testing methods, data analysis results obtained, and recommended changes.

Jan 1, 1992

By J. E. Gebhardt, P. E. Richardson

External control of the electrochemical potential of a bed of mineral particles was investigated by the US Bureau of Mines as a method for controlling particle interaction with organic collectors and, thus, flotation response. A cylindrically shaped, 200- to 300-g bed of sulfide mineral particles was used as the working electrode in an electrochemical-flotation cell. In a pH 9.2 sodium tetraborate buffer, chalcocite floated with ethylxanthate at applied potentials [=] - 0.25 V (versus the standard hydrogen electrode) ; pyrite floated at potentials [=] 0.15 V. Differential separation of a chalcocite-pyrite mineral mixture was obtained by controlling the potential, but the flotation response of the mixture did not follow the behavior predicted from measurements on the individual mineral beds. Chalcocite dissolution products had a deleterious effect on chalcocite-pyrite separation by activating pyrite so that it floated below the potential (~ 0.13 V) at which xanthate is oxidized to dixanthogen. A pyrite bed activated with a copper(II) sulfate solution exhibited a flotation response with a potential dependence between that of chalcocite and pyrite. Pyrite dissolution products had no effect on chalcocite flotation.

Jan 1, 1988

By T. F. Tomb

This paper describes field and laboratory investigations conducted on a dust-collection system recently designed for integral use with a continuous mining machine. The results of the field study showed that the average respirable dust concentration measured at the machine operator's position was reduced by about 60 percent (from 8.7 to 3.5 milligrams per cubic meter), and total and respirable dust concentrations in the return air were reduced by approximately 70 percent. The data indicated that approximately 20 percent of the dust generated at the face was not passed through the scrubber. The lab-oratory results showed that the overall efficiency (by particle count) was approximately 80 percent for total dust concentrations (minus 20 micrometers in size) typical of those encountered underground. Calculations based on total dust concentrations measured during the underground study indicated that the respirable mass concentrations of the effluent from the scrubber would still exceed acceptable levels even if scrubbing of all the air at the face were possible.

Jan 1, 1973

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

The object of this paper is to describe the adaptation of electrical resistivity measurements to the particular case of exploration in which the surface is an expanse of water (river, lake, sea). Water in itself does not constitute an obstacle to electrical exploration. It is merely an overburden, which is fluid instead of being solid, and as a consequence the routine of the measurements has to be modified. Also, in many instances, the liquid under consideration is highly conductive (salt water). This introduces an additional difficulty into exploration work, and has to be overcome by the geophysicist. We do not propose to discuss here the basic principles of electrical resistivity measurements, which have been dealt with in various previous papers,' but will simply recall the two fundamental techniques which govern its field application: 1. Horizontal exploration, or method of the resistivity map, in which a series of electrical measurements are carried out at various stations, keeping the same electrode spacing. Thus, a horizontal layer of the subsoil, of a practically constant thickness, is explored. 2. Vertical exploration, or "vertical sounding"2 method, in which a seriesr of measurements is made with increasing electrode spacings at one or several stations. In this way, the apparent resistivity is determined at a given station for various increasing thicknesses of the ground.

Jan 1, 1934

By E. L. Garton

The United States Bureau of Mines has recently collected samples of crude petroleum from wells in the newly developed Joiner. Kilgore, and Longview fields of Rusk and Gregg Counties in the East Texas district, and from the Van field of the East Central district of Texas.

Jan 1, 1931

By A. W. Fahrenwald

"About two years ago the Bureau of Mines, Department of the Interior, and the University of Idaho undertook an investigation of classification in its relation to table concentration of Idaho ores. The cooperation of the management of the Bunker Hill & Sullivan Co. in placing at our disposal their West Mill and facilities as desired, offered an unusual opportunity for studying the field of hindered classification in its practical and economic relation to table concentration.It has been shorn theoretically, and demonstrated experimentally, that ore products are more easily and economically concentrated on tables if the natural feed, consisting of various minerals and of all sizes of particles of each mineral, be classified or grouped into a series of products in which the mineral particles of greatest density are small in diameter relative to the diameter of the mineral particles of lesser density. Products in which the maximum difference in diameter of light and heavy minerals occurs are to be obtained only by true hindered settling classification. To our knowledge there has never been a really good hindered settling classifier used in practice and the present tendency seems to be to by-pass any attempt at such classification.After a careful study of the nature of hindered classification and of the requirements for hindered settling in practice, a classifier has been developed that takes fullest practical advantage of the widely known, but generally only meagerly understood, condition of hindered settling so well analyzed a number of years ago by Dr. Richards.The present paper presents briefly some of the more important practical results accruing through the investigation."

Jun 1, 1924

By A. Blake Caldwell

Northwest frontier is here defined as Alaska, the Yukon, the Northwest Territories and northern British Columbia. The mineral potential of this area is great and will unfold in the decade ahead but now the largest single producer is the Pine Point lead-zinc mine in the NWT about 1200 km north of Edmonton, Alta., close to the south shore of Great Slave Lake. The mill, initially designed for 4540 mtpd, was expanded to 7250 mtpd in 1969. This operation is described in detail in Mining and Concentrating of Lead and Zinc, Vol.1, Chapt. 17, SME/AIME in the article by W. H. R. Gibney.

Jan 1, 1971

By B. J. Moore

This publication contains routine analyses and related source data for 419 natural gas samples from 22 States collected during calendar year 1964 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863/ and 576.4/ Six previous publications have been made to present the results of 6,293 gas analyses made by the Bureau of Mines, Helium Activity, prior to 1964. The first three, Bulletins 486,5/ 576,6/ and 617,7/ contain analyses and related source data on 5,214 gas samples collected from

Jan 1, 1966

By G. J. Koons, J. L. Uhrie

Field density studies carried out at the Phelps Dodge Chino Mine have found that truck-induced compaction is limited to the upper 2.4 m (8 ft) of an individual lift. Hydraulic properties of material compacted to field densities were determined in a laboratory setting. Saturated flow models were then run, simulating the effect of compacted zones within a stockpile. Modeling shows that compaction can prevent solution flow through large portions of the stockpile. This implies that care must be taken to ensure that ripping is carried out to a depth of at least 2.4 m (8 ft) across the entire stockpile to achieve uniform solution flow. Uniform solution flow will result in maximum leach recovery.

Jan 1, 2002

By M. M. Austin

PURE metallic tantalum, from a practical standpoint, is one of the newer developments in the metal field. Although it was used as filament in incandescent lamps in 1906, only within the last five years has the metal been available in sufficient quantity and suitable form for more general application. In addition to corrosion-resisting properties and high melting point, the metal has an ability to withstand unusual amounts of cold working. It affords some striking demonstrations of block movement during plastic flow.

Jan 1, 1930

By Charles S. Barrett

Metallurgists are making use of the stereographic projection to a steadily increasing extent. In the last five years no less than 20 papers in American metallurgical journals alone have employed the stereographic projection; recent books on physical metallurgy, plastic deformation, X-rays and their applications, and crystal structure use it. Mineralogists have used the stereographic projection for many years in the description of symmetry classes and crystal planes, for it presents an accurate, easily understood plot of any angular relations in crystals with all unessential features eliminated (such as the accidentally determined size and shape of crystal faces). In metallography and physical metallurgy the projection is much used for the analysis of markings appearing on polished grains: slip lines, twins, cracks, structures formed by precipitation, magnetic-powder patterns, etch pits, etc. Data from certain types of X-ray photograms are most conveniently analyzed by its use, particularly those for determining the orientation of single crystals or the preferred orientation of grains in an aggregate. Calculations of how to tilt or cut a crystal parallel to a certain crystallographic plane or to reflect X-rays from a certain plane are rapidly carried out. It has been adopted almost universally to the exclusion of other methods by those studying the deformation of metallic crystals, save where the accuracy required is greater than a few tenths of a degree. Any directional property in a crystal or polycrystalline material can be shown on a stereographic projection; for example, the modulus of elasticity, yield point, etc. It has been repeatedly called to our attention that there is need of an elementary explanation of the principles and methods of stereographic projection, covering all the common applications in the field of metallography and physical metallurgy. The following contribution is an attempt to fill this need. The description of each method is supplemented with references to publications in which the method has been used. For convenience to the reader, these illustrative references are chiefly in American journals, particularly the publications of the American Institute of Mining and

Jan 1, 1937

By Rollyn P. Jacobson

THE town of Pacific, in Jefferson County, Mo., is 127 miles west of St. Louis. Since the area lies entirely on the flood plain of a cutoff meander of the Meramac River, it was considered a likely environment for accumulation of commercial quantities of sand and gravel. Excellent transportation facilities are afforded by two major railways to St. Louis, and ample water supply for washing and separation is assured by the proximity of the river. As a large washing and separation plant was planned, the property was evaluated in detail to justify the high initial expenditure. An intensive testing program using both geophysical and drilling methods was designed and carried out. The prospect was surveyed topographically and a 200-ft grid staked on which electrical resistivity depth profiles were observed at 130 points. The Wenner 4-electrode configuration and earth resistivity apparatus" were used. In all but a few cases, the electrode spacing, A, was increased in increments of 11/2 ft to a spread of 30 ft and in increments of 3 ft thereafter. Initial drilling was done with a rig designated as the California Earth Boring Machine, which uses a bucket-shaped bit and produces a hole 3 ft in diam. Because of excessive water conditions and lack of consolidation in the gravel there was considerable loss of hole with this type of equipment. A standard churn drill was employed, therefore, to penetrate to bedrock. Eighteen bucket-drill holes and eight churn-drill holes were drilled at widely scattered locations on the grill. The depth to bedrock and the configuration will not be discussed, as this parameter is not the primary concern. Thickness of overburden overlying the gravel beds or lenses became the important economic criterion of the prospect.** The wide variety and gradational character of the geologic conditions prevailing in this area are illustrated by sample sections on Fig. 2. Depth profiles at stations E-3 and J-7 are very similar in shape and numerical range, but as shown by drilling, they are measures of very different geologic sequences. At 5-7 the gravel is overlain by 15 ft of overburden, but at E-3 bedrock is overlain by about 5 ft of soil and mantle. Stations L-8 and H-18 are representative of areas where gravel lies within 10 ft of surface. In most profiles of this type it was very difficult to locate the resistivity breaks denoting the overburden-gravel interface. In a number of cases, as shown by stations M-4 and H-18, the anomaly produced by the water table or the moisture line often obscured the anomaly due to gravel or was mistaken for it. In any case, the precise determination of depth to gravel was prevented by the gradual transition from sand to sandy gravel to gravel. In spite of these difficulties, errors involved in the interpretation were not greatly out of order. However, results indicated that the prospect was very nearly marginal from an economic point of view, and to justify expenditures for plant facilities a more precise evaluation was undertaken. The most favorable sections of the property were tested with hand augers. The original grid was followed. In all, 46 hand auger holes were drilled to gravel or refusal and the results made available to the writer for further analysis and interpretation. When data for this survey was studied, it immediately became apparent that a very definite correlation existed between the numerical value of the apparent resistivity at some constant depth and the thickness of the overburden. Such a correlation is seldom regarded in interpretation in more than a very qualitative way, except in the various theoretical methods developed by Hummel, Tagg (Ref. 1, pp. 136-139), Roman (Ref. 2, pp. 6-12), Rosenzweig (Ref. 3, pp. 408-417), and Wilcox (Ref. 4, pp. 36-46). Various statistical procedures were used to place this relationship on a quantitative basis. The large amount of drilling information available made such an approach feasible. The thickness of overburden was plotted against the apparent resistivity at a constant depth less than the depth of bedrock for the 65 stations where drilling information was available. A curve of best fit was drawn through these points and the equation of the curve determined. For this relationship the curve was found to be of the form p = b D where p is the apparent resistivity, D the thickness of overburden, and b a constant. The equation is of the power type and plots as a straight line on log-log paper. The statistical validity of this equation was analyzed by computation of a parameter called Pearson's correlation coefficient for several different depths of measurements, see Ref. 5, pp. 196-241. In all but those measurements taken at relatively shallow depths, the correlation as given by this general equation was found to have a high order of validity on the basis of statistical theory.

Jan 1, 1956

By Tominaga Y

Mine ventilation control is one of the most important techniques to suppress the disastrous region within a limited area, to have enough time of emergencies (ignitions, fires and so on) for underground workers. The purpose of this paper is to introduce the simultaneous controlling of mine ventilation by using, micro computer connected to various kinds of sensors. In this study, basic of mine ventilation and graph theory are used for making computer programs when the characteristic curves of fans and temperature distribution in an underground roadway network are given.

Jan 1, 1981