Search Documents

By Franklin H. Persse

To meet escalating energy requirements, substantial increases in production from the strippable coal and lignite deposits in eastern Montana, western North Dakota, and northeastern Wyoming already have occurred, and further expansions are expected at least until the year 2000. Such production, attributable largely to rising demand for low-sulfur coal, must be accomplished with a minimum of adverse effects on the environment. Information on geology, climate, and current land use in the Upper Missouri River basin is presented in the Bureau of Mines review as a guideline to what operators may expect during and after mining. Proven methods of protecting the air and water from pollution and of restoring mined land for other uses are described, and untried methods of land reclamation, some with equipment yet to be manufactured, are discussed as possible means of maintaining aesthetic values in the basin. Costs incurred to protect the environment are part of the production cost and thus are borne by the ultimate consumer. Unit production costs are less for the thick coal and lignite deposits of the basin than for the thinner but higher Btu coal deposits of the Eastern and Midwestern United States. Precise comparisons of environmental protection costs between mines in such disparate areas cannot be made, because of differences in physical conditions, accounting procedures, and other variables.

Jan 1, 1975

By Marlin E. Sandlin

NORTH-CENTRAL United States is now, and will continue to be, a natural market for Canadian crude oil. This area is a natural market for many basic reasons. There are no physical barriers along the border of our countries. This market is in dose proximity to Canadian production. This market is already joined by crude oil pipe-1,ines to numerous producing areas of Canada. The tariff barriers are reasonable. We are not handicapped by mandatory quota restrictions. There are many of us who desire lo sell Canadian crude oil in this market. Further, and what is really important, there are many of us who desire to buy Canadian crude oil for this market. It is fundamental that for crude oil to be sold in the world market, it must ?be sold at competitive prices. At the same time, it is important that such competitive price must result in a fair price for the crude oil at the we1lhead. The factors of nearness to market, cheap pipe line transportation, and reasonable United States tariffs, all tend to make ?possible a competitive market and a fair wellhead price.

Jan 1, 1958

By Robert W. Fullerton, Donald T. King

INTRODUCTION AND THEORY by Robert W. Fullerton In coal preparation plants, as in any industrial operation where raw materials are handled, nuisance problems arising from the generation of dust are inevitable. Devices for the control or collection of dust are there- fore essential components of the plant process equipment. The general term "aerosol" is applied to small particles suspended in a gaseous medium, usually air, whose velocity under the force of gravity is small enough that the particles remain suspended for a reasonable length of time. Aerosols can be classified as dust, smokes, fumes, mists or fogs. Dust includes particles originally formed by pulverization of materials by such processes as crushing, grinding, drilling, blasting and abrasion. Smoke includes particles formed from the burning of organic materials. Fumes are particles formed by processes such as condensation and sublimation, usually at high temperatures. Mists or fogs are particles formed by the condensation of water or other vapors on some nuclei. The size of aerosol particles is generally designated in units of microns, there being 1000 microns to a millimeter and 25,400 microns to an inch. Particles of about 10 microns or above are visible to the naked eye. Table 14-1 shows size characteristics of the general classifications of particles discussed above and includes typical examples of particles commonly en- countered. Table 14-1 also shows the relationship between micron size and standard screen mesh sizes. Smoke and fume are usually in the range of 0.01 to one micron, dusts are in the range of one to 400 microns, mists are in the range of 0.1 to 100 microns, and fogs are in the range of one to 100 microns. For purposes of dust control, particles greater than 10 or 20 microns in size are considered large, particles one to 10 microns are considered fine and particles below one micron are ultrafine. Sources of Dust Because coal is relatively friable, the mining and subsequent handling operations break part of the coal into dust that can be readily carried by currents of air. In a coal preparation plant mechanical handling operations such as unloading, transferring from one belt to another, screening, cleaning, and crushing in a dry state result in the generation and release of varying amounts of additional dust. The dust problem, of course, is much less serious in plants employing entirely wet processing. In addition to dust from handling operations, thermal drying of the fine coal product frequently presents another dust collection problem. Most coal driers are

Jan 1, 1968

By Q. Xiao, R. Naidu, W. Li, S. Song

Acid mine drainage (AMD) derives from the oxidation of sulfide minerals, primarily pyrite (FeS2), and is the most severe environmental issue facing the minerals industry. The most common short-term approach to AMD treatment is migration control, such as acid neutralization and metal/metalloid and sulfate removal, through the addition of alkaline materials, including lime (Ca (OH)2), limestone (Ca CO3), gangue minerals and industrial wastes. This requires the continuous input of materials and may result in the production of a vast amount of secondary sludge requiring further treatment and disposal. Addition of chemicals is usually more important in metal/metalloid removal than in sulfate removal unless the sulfate is present in very high concentrations. A more promising long-term strategy for AMD prevention is source control through the complete removal of pyritic minerals and encapsulation of potential risk minerals by coating with impermeable surface layers. This is regarded as the most cost-effective approach, although the mechanisms underpinning this and the implementation procedures are yet to be fully elucidated. It is likely that long- and short-term practices can be combined to optimize the remediation of contaminated mining sites. Some factors such as differing geological and mineralogical characteristics and transportation costs must also be considered for the successful implementation of AMD prevention and remediation strategies. This review also considers some implications for AMD remediation, but the promising bioremediation of AMD is not discussed as it has been extensively reviewed.

By James C. Foley

In-situ characterizations of green state part density and sintering state have long been desired in the powder metal community. Recent advances in non-contact electromagnetic acoustic transducer (EMAT) technology have enabled in-situ monitoring of acoustic amplitude and velocity as sintering proceeds. Samples were made from elemental powders of Al (99.99%), Al (99.7%), Ag, (99.99%), Cu (99.99%) and Fe (99.9%). The powders were pressed in a uniaxial die and examined with acoustic waves for changes in velocity and amplitude during sintering. The changes in acoustic properties were correlated with mechanical properties. Evolution of a series of reverberating echoes during sintering is shown to provide information on the state of sintering, changes in sintering kinetics as well as having the potential for detection of interior flaws.

Jan 1, 2001

By Delahey G, Dunne R

At New Celebration Gold Mine the advent of treating primary sulphide ores resulted in decreased gold recoveries of four to ten per cent. The grind coarsened due to an increase in ore hardness and gold in the residue was found to be associated with pyrite. Finer grinding improved recoveries but was impractical as production rates would have decreased to unacceptable levels. An alternative approach that has proved to be viable combines both gravity separation, to recover the coarse gold bearing sulphides, and then regrinding the concentrate in a tower mill prior to releaching in the cyanide leach circuit. The tailings treatment plant was commissioned in December 1990 and details of the first 18 months' operations are Provided.

Jan 1, 1993

Strengthening a mine with the Power of their Employees: ?Imagine if the global economy collapses, your head office calls, and tells you to shut down for 3 months... now what do you do? ? HVC Business Improvement Initiative Why did we need help ? External Events ? How we responded ? How we worked with Westwind ? Alignment ? Priorities ? Coaching ? Focus Groups ? Innovation ? What worked / Opportunities ? Questions

Nov 1, 2011

By E. B. Olds, Burt. B. P.

THE mines of the Consolidated Coppermines Corporation are at Kimberly, in the Robinson mining district, White Pine County, Nevada. [ ] The blanket-like ore body is a disseminated copper deposit occurring in monzonite porphyry and, in general, is thoroughly fractured, altered, and soft. Contained in the porphyry ores of the extreme westerly end of the ore body are pendants of hard garnetized limestone. A younger monzonite porphyry underlies the ore-bearing porphyry, which in turn rests on limestone and shale. Block caving is the standard method of mining. Because of the undulating top and bottom contours of the ore body, the main haulage level was selected and driven at an elevation calculated to be the most economic depth below the major tonnage sections of ore. Fig. I shows a general section of the Emma Nevada ore body taken through its long axis, which lies roughly in an east-west direction. Mine openings in either type of porphyry require heavy timbering and constant maintenance and repair, particularly in horizons at or near the ore body contact. Where the ore lies close to the haulage level, slusher hoists and scrapers are used to transport horizontally the ore to the main haulage drift (Fig. 2). For the extraction of high-lying ores, a system of branch raises is used; and the ore is mined by gravity. Slushing methods are used also on the high-lying ore-body fringes. Slusher drifts are often driven from the fringe branch raises that have already served their purpose, in order to minimize the cost of the preparatory work in mining the thinner portions of the ore body (Figs. 3 and 4). When a block of ore is developed and undercut, it is economical to mine it as rapidly as the ore will cave efficiently; and this procedure often presents safety problems because of men with equipment working in a relatively congested area. The single-track main haulage drift is about 1 ½ miles long, and lateral haulage drifts are driven under the ore body at intervals determined by the height of the ore body above the haulage level. In order to minimize repair and maintenance, the

Jan 1, 1946

By J. Schnarr, D. Deever, E. Johnson

"The above committee sent out a questionnaire to the gold mines for the purpose of learning what units and methods are currently in use in the mines as the first step in an attempt to agree on standard units to be used in any papers or reports that may be given to other mines or presented at meetings. The next step is to try to arrive at acceptable standard units for reporting and methods of making tests. It was suggested by Mr. J. Jardine of Eldorado Mining and Refining that the use of the metric system should be seriously considered. It was also brought out that there was no intention of having any mine change their methods to the standard for internal reporting as this would involve too much change. However for external reporting there shouldn't be too much difficulty in converting to the accepted standard units.On the following pages are the reports of those mines that replied to the questionnaire.MALARTIC GOLD FIELDS LIMITEDP.A. Coulter1. All assays - Ounces per ton2. Consumption of reagents - Pounds per ton3. Reagent strength of solutions - Pounds per ton4. Reducing Power - As described in C 0 I.L, Analysis of Cyanide Solutions5. Pulp Densities - Grams per litre6. Screen Analysis (Tailings) A sample of 150 gms is washed on a 200 mesh screen. The plus 200 mesh material is dried and ro-tapped for fifteen minutes. The plus 200 mesh portions are weighed cumulatively (the balance is considered -200 mesh) and reported in per cent."

Jan 1, 1967

The products of the steel tube industry play an important part in the production,' transrzission and refining of oil. Steel tube manufacturing is already well established in Australia and supplies the petroleum industry with its requirements" within the .present limitations of the various tube plants., With the discovery of oil in commercial quantities in this country, the steel tube industry could be expected to extend its scope to cover a much wider range; of oil country tubular goods, line pipe and refinery. Tubing.

Jan 1, 1962

For the US coal industry, 1978 was a nightmarish recurrence of 1977 as the United Mine Workers strike cut into production during the first three months of 1978, followed by the strike against the Norfolk and Western Railway during the summer and early autumn. Coking coal production was floored by the one-two punch of environmental constraints on US coke ovens and competition from low-cost, high-quality imports. At the same time, US ex orts of coal fell to their lowest level since 1962. And in the face of all of this, steam coal consumption was sluggish as utilities burned huge amounts of oil to conserve coal stockpiles during the UMW strike. This was followed by decreased electrical demands due to mild summer weather in many parts of the country and dramatically improved availability of hydroelectric power.

Jan 5, 1979

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

COMPARED with the equipment used in most industrial processes, the open-hearth furnace has a relatively short life. The most important quality of an open-hearth refractory, therefore, is its rate of failure. This discussion of the physics and chemistry of the individual refractory materials will keep uppermost the question "Why, how, and where does it fail?" CAUSES OF FAILURE The principal causes of failure of open-hearth refractories are, in their order of importance : 1. Reaction with iron oxides. 2. Reaction with slag. 3. Flow and failure under load. 4. Melting. 5. Spalling. 6. Mechanical breakage. Reaction with Iron Oxides and Slag. Reaction with iron oxides and slag is by far the most important cause of failure. Liquid iron oxide comes near to being the "universal solvent" sought for by the alchemists. Among the materials commonly used in the open-hearth furnace, magnesia has the greatest resistance to this liquid and fireclay the least. The relations of iron and oxygen at high temperatures are illustrated in Fig 14-18. The liquid iron oxide that forms wherever iron is in contact with air or combustion gases cannot be given a definite formula. The percentage of oxygen at steelmaking temperatures may range from 21 to 28 (iron 79 to 72), depending upon the temperature and the oxygen pressure and also upon whether or not the liquid is in equilibrium with metallic iron. Oxide mixtures exist not only in the solid and liquid phases but also in the vapor phase, for metallic iron and its oxides have

Jan 1, 1964

By Gabriel Voicu, Marc Bardoux, Ross Stevenson, Nuno Machado, Jean Lafrance

"Abstract - Paleoproterozoic gold is found in two different volcano-sedimentary sequences and intrusive bodies separated by 600 km within the Guiana Shield. The 2148 Ma St-Élie granite intruded volcanic-arc sequences of the Paramaca Group, whereas the 2096 Ma Omai stock penetrated backarc/ island-arc sequences of the Barama-Mazaruni Group. Positive ?Nd values suggest that both suites lack Archean crustal contaminants, which is consistent with an origin in an oceanic arc setting.The St-Élie deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented chiefly by pyrrhotite and pyrite. Biotite, calcite, and chlorite are the main gangue minerals. The alteration haloes at St-Élie feature a strong potassic zone, which is absent at Omai. The ore-controlling structures are ductile and the vein emplacement is related mainly to contemporaneous, high-angle ductile shear zones. The St-Élie deposit formed at temperatures >350°C. The stable isotopes values are compatible with a magmatic or metamorphic source.The Omai deposit is characterized by quartz-dominant vein systems with minor metallic minerals, represented mainly by pyrite. Ankerite, scheelite, albite, and chlorite are common gangue minerals. The vein emplacement is syn- to post-deformation and it is related mainly to brittle shear zones with low-angle, stockwork networks and breccia zones. The Omai deposit formed in a temperature range between 250°C and 170°C, much lower than the St-Élie deposit. The stable isotope values are compatible with mixing between deep-seated fluids of metamorphic or magmatic origin with surface- derived fluids.These differences between St-Élie and Omai are interpreted in terms of their depth of formation. Alteration patterns, structural elements, and paragenetic assemblages indicate that the gold at St-Élie was most probably emplaced at a mesozonal depth, whereas the Omai setting yields evidence for epizonal conditions."

Jan 1, 1999

By Philip Wilson

Tun mines of the Calumet & Arizona Mining Co. are situated in the Warren Mining District, Cochise County, Arizona, between Bisbee and Warren and adjoin those of the Copper Queen Consolidated Mining Co. and the Shattuck Arizona Copper Co. Paleozoic limestones of considerable thickness have been intruded by granite porphyry. A great stock of the intrusive outcrops boldly near the city of Bisbee and is known as Sacramento Hill. From this central core the porphyry has tongued out into the limestone for many thousands of feet as dikes and sills of irregular shape and variable dimensions. Churn drilling has recently developed a large tonnage of secondarily enriched copper ore in the main porphyry mass of Sacramento Hill. While some ore has been found in porphyry in other parts of the district it is relatively unimportant compared with that which occurs in the Paleozoic limestone as irregular lenses replacing favorable beds near porphyry contacts or associated with well-marked fracture zones often many hundreds of feet away from the intrusive. In a zone extending from Sacramento Hill for a distance of from 1,500 to 3,000 ft. the limestone has been extensively metamorphosed and in this contact metamorphic zone the ore occurs through a known vertical thickness of upward of 900 ft. and individual orebodies often show extension in a vertical direction of over 200 ft. At a greater distance from the intrusive stock the ore occurs as lenses of greater horizontal than vertical dimensions with an average thickness of approximately 30 ft. An exception to this rule is found in the occasional steeply dipping mineralized fractures, almost true tabular veins, which are found long distances away from the zone of contact metamorphism.

Jan 7, 1916

By J. B. Morrow, D. H. Davis

THERE are two general approaches to the problem of increasing profits from an operation. One is to lower expense; the other is to raise income. Mechanical preparation of coal may be used for either purpose but a prudent consideration of many details must precede any decision lest the results be negative instead of positive. It is quite possible that any net gain will result from a combination of the two. Since mechanically prepared coal invariably is a better product qualitatively than a hand-picked coal from the same mine, it is a reason- able expectation that the customer will be willing to increase the producer's income by paying a higher price. Or there may be the possibility that a combination of mechanical mining plus mechanical cleaning will give a lower over-all production cost for the coal in the railroad car. More likely, there will be found a combination of these two factors. From the customer's point of view, the competitive delivered cost per B.t.u. considered in relation to such incidental factors as dust nuisance, handling properties, ash disposal, and ash fusibility determines what he will pay. In a bulk tonnage product such as coal, freight is a very considerable part of the delivered fuel cost, and obviously freight paid on incombustible ash has no economic attractions. INCENTIVE FOR CLEANING Coal is prepared in four major ways: 1 (I) by screening or sizing, (a) by mixing or blending, (3) by cleaning, including hand picking and mechanical cleaning, (4) by dustless treatment. By a combination of any or all of these methods, coal can be prepared to standard specifications. It is easily possible to have good cleaning and still get a poor final product because of faulty screening or mixing,

Jan 1, 1943

By Joseph Cervik, Maurice Deul, Albert Sainato

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pct; reductions of 38 to 79 pct were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No. 3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By Walter Harvey Weed

The notes given in this paper, the result of observations made during recent brief professional trips to the northern States of Mexico, are offered as a slight contribution to the geological knowledge of a region little known, but long famous for its rich gold- and silver-mines. They are not detailed geological studies, but they contain, I believe, the salient facts. The following districts were visited: 1. Santa Eulalia (silverlead) ; 2. Parral (silver-lead); 3. Las Vigas (copper); 4. Jimenez (copper); 5. Guadalupe y Calvo (gold); 6. La Cumbre (gold); 7. Palmarito (silver); 8. Cananea (copper); 9. Sierra Pinitos (gold); 10. Sierra Azul (gold). 1. The Santa Eulalia Silver-Lead Deposits. Seventeen miles SE. of Chihuahua is the mining district of Santa Eulalia, to which that city owes its origin and long prosperity. Discovered in 1703, this district has been, and still is, one of the great silver-lead producers of the world. For 86 years after its discovery, the total output upon which the crown tax was paid amounted to $112,000,000. Worked until within the last 20 years by the most primitive methods, without machinery of any kind, the deposits continued to yield a vast treasure of silver; at present the yearly tonnage far exceeds that of former times. A broad-gauge road runs from Chihuahua up the valley of a small creek to the village of Santa Eulalia, which is situated within the borders of the mountains of that name. A few miles out of Chihuahua a narrow-gauge railway, owned by the Chihuahua Mining Co., branches off to the mines. This road ascends a smooth but steeply-rising plain to the base of the mountains, and winds about the slopes until the mines are

Jan 1, 1902

By W. H. Oppelt

Converting small-particle lignite to a stable, storable fuel of relatively high heating value was investigated. The fuel was prepared by thermal pretreatment of the lignite in an 8-inch i. d. rotary-drum retort, then the pretreated material was pelletized in an experimental 15-inch-i. d. rotary-drum pelletizer. Pelletizing tests were made with both starch and bituminous binders. During the first phase of the project, the quantity, composition, and heating value of products from the thermal processing of Kincaid lignite from Burke County, N. Dak., in an B-inch i. d. rotary-drum retort were investigated at a series of temperatures from 250° to 950° F. to establish optimum conditions for preparing feed material for pelletizing. To determine the response to thermal treatment of different lignites, 5 other lignites from Divide, McLean, Mercer, and Stark Counties, N. Dak., and 1 lignite from Saskatchewan, Canada, were processed at 700° F.

Jan 1, 1958