Search Documents

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 3, 1918

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,310-acre Diablo Mountain (Additional) study area (OR-001-058), in order to evaluate its identified mineral resources and occurrences. The study area lies along the east shore of saline Summer Lake in Lake County, OR, about 145 miles southeast of Bend and 45 miles northwest of Lakeview. The climate is semiarid and temperate, and the study area is almost treeless. Geologically, the (Additional) study area is in a region of fault block-formed mountains and basins, characterized by interior drainage. The area is mainly underlain by unconsolidated Quaternary and Pleistocene lake and playa sediments, which may include subsurface evaporite mineral deposits and resources. Near the center of the eastern margin of the study area are an occurrence of dolomitic limestone of unknown extent, and an area of basalt outcrop totaling 1.5 square miles. A veneer of windblown sand covers about one-half the study area.

Jan 1, 1989

By R. C. Richardson

Barite Worldwide barite production for 1985 decreased 1.3%, while US barite production increased 1.4%, according to US Bureau of Mines statistics. The increase in US production is attributed to heavy demand for oil and gas drilling during the first quarter and an unrealized heavy expected demand in oil and gas markets for the last quarter. Nevada accounted for 82.1% of the 807 kt (890,000 st) of barite produced in the US last year, according to the Bureau. Other producing states were California, Georgia, Illinois, Missouri, Montana, Tennessee, and Washington. In 1985, the US imported 1.8 Mt (2 million st) of crude barite and 64 kt (71,000 st) of ground barite. China led the way with 43.3% of the total. Imports from India accounted for 21.6%; Morocco, 15.5%; and Thailand, 5.6%. The 1.8 Mt (2 million st) of crude barite imported is an 18.8% increase over 1984. Apparent consumption of barite for 1985 was about 2.6 Mt (2.9 million st), a 15.7% increase from 1984. Due to very low drilling rig activity during the last quarter of 1985, actual consumption is probably less as crude barite inventories at mines and plants increased. According to the Bureau, 90% of barite consumed in 1985 was for the oil and gas market. Paints, rubber, glass, and other chemical uses consumed the other 10%. With the price of oil falling dramatically early in 1986, the outlook for oil and gas drilling looks to be significantly lower than 1985. This lower demand for barite, coupled with the high year-end inventories, should lower both imports and domestic production. Significant lower prices on imported barite are expected, especially from China, Morocco, and India. This also could further lower US production of barite this year.

Jan 5, 1986

By R. W. Shoenberger, J. D. Clendenin, W. L. McMorris, N. Schapiro, B. R. Kuchta, A. A. Terchick, R. J. Gray, J. G. Price

INTRODUCTION * The United States is fortunate in having enormous reserves of metallurgical-grade coals. Although these coals are better in quality and more accessible than most coals found throughout the rest of the world, the best grades of these coals are being depleted. Consequently, more efficient exploration tools and techniques, such as advanced methods of core drilling and logging, correlation by palynology,** stratigraphy, paleontology and petrography are being used to help assess the extent and quality of the remaining coal reserves. Exploration and assessment of new and existing coal properties become of utmost importance in determining (1) the economic justification for mining the coal, (2) the optimum design of the preparation plant and (3) the most effective use of the coal. Fortunately, the cost of mining coal has remained stable because of better mine planning, more efficient operations and increased mechanization of mining operations. However, increased mechanization raises the amount of impurities in the coal mined, and this requires more and better coal beneficiation to meet the more stringent quality requirements set by the market. Besides, mechanical miners also produce relatively fine coal and, to ensure maximum liberation of impurities, much of the coal presently being used must be crushed to a finer size prior to preparation. The bulk of all coals presently used in this country is mechanically cleaned, much of it at a lower specific gravity than in the past. This necessitates the use of new and improved processes and equipment for coal washing and recovery, such as heavy-medium cyclones and vessels, and froth flotation cells. However, because wet-cleaning processes are pre- dominant in the United States and fine coal retains large amounts of moisture, the increased production of cleaned fine coal accentuates the need for new or improved methods and equipment for dewatering and drying this coal. The larger amounts of coal being beneficiated and the use of new and improved beneficiation processes will aid in controlling and ultimately eliminating sources of pollution. Modem coal markets demand coals that meet rigid specifications. Most coals are purchased under contracts that specify moisture, ash, and sulfur contents, or heating value, depending upon the end use. There has also been a growing trend toward specifying other properties, including particle size and coking capability. These specifications may include not only the * Editor's note: Because of the numerous and varied contributions of the associate authors of this chapter, the text does not differentiate between sections prepared by each individual as has been done in other chapters. ** Palynology is the study of plant microfossils, especially spores, pollen, and other types of fossils not usually studied by paleontologists.

Jan 1, 1968

By N. B. Pilling

The deleterious effect on the mechanical properties of copper, re-sulting from heating in contact with reducing gases, is well known, but the mechanism of the action does not appear to have been definitely established. The purpose of the present investigation was not to determine the exact variations in physical quality of commercial copper, with its various impurities, as dependent upon the composition of the gas, temperature of exposure, etc., but rather to study the nature of the action and the conditions under which it occurs. The physical result of the so-called "gassing" of copper has been generally described as the development of "brittleness." There appears to be a striking decrease in tensile strength, associated with a considerable loss of ductility, and a small copper strip or wire affected in this way can be snapped in two when bent. Larger articles may have an outer layer alone affected, which can be detached from the core by hammering or bending. Perhaps the earliest reference to this subject is that of Heynl in 1900, and among the later observers may be mentioned Archbutt,2 Bengough and Hill,3 Johnson,4 Mathewson and Thalheimer,5 and Ruder.6 Bengough and Hill, while working with arsenical copper, were the first to suggest the possibility of the formation of gases within the copper itself, while Ruder endeavored to explain the action by the reduction of the

Jan 1, 1919

By Bruce D. Hanson

The Bureau of Mines conducted a series of experiments using four different coal types to determine the effect of attack angle and symmetric bit wear on airborne respirable dust (ARD) generated by point-attack bits and in energy consumption. Neither had a significant effect on ARD at the 95-pct confidence level, but bit wear had a significant effect (95 pct confidence) on specific energy (energy per gram of cut coal) for three coal types, Depth of cut was the most significant factor affecting ARD and specific energy.

Jan 1, 1979

The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 12, 1916

By Bin H

East Guangdong tin province overlaps the southmost part of the mesozoic magmatic arcof continental margin type in Southeast China and is dominated by mesozoic syntectic magmatism,which associated to tin mineralization. It is distinguished from Nanling tin province but quite close to NW Bolivian tin province in both tectonic and magmatic relations.Tin deposit's mostly of cassiterite-sulfide, cassiterite-silicate formations are localized along exsocontact zone of granitoid batholith or stock, boundary area of volcanic depression, or, within volcanic edifice. Petrochemistry studies show tin was concentrated as intermediate-acidic magma evolved by fractional crystallization. Xiling tin deposit of vein type related to extrusive... the lava dome was formed at T C 221-301 and at very shellow depth,seems to correspond to type A in classification for Bolivia tin deposits by J.N.Grant. Tashan tin deposit of dissemination type related to hypergene intrusive facies,with mineralization occured in endocontact zone of granite porphyry dykes is considered as porphyry type,which spported by H-0 isotope and gas-liquid inclusion evidences. It formed at T C 250-430, comparable to Bolivia porphyry tin deposits,but at a greater depth 1.3 3.0km.A model for known tin deposits in East Guangdong was worked out. A good prospecting perspective was revealed for the potential type of tin deposit in East Guangdong--subvolcanic porphyry tin deposit.

Jan 1, 1990

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986

By Andrew Mayer

EARLY in 1942 National Lead Co. was requested by the War Production Board to construct and operate a plant for the Government to produce magnesium by the ferrosilicon process which had been developed by Dr. L. M. Pidgeon in the laboratories of the Canadian National Research Council. A contract with the Defense Plant Corporation was concluded in May 1942 and Magnesium Reduction Co., a wholly owned subsidiary of National Lead Co., was formed to carry out this project. The capacity of the plant was rated at 10,000,000 lb. of magnesium per year, equivalent to an average production of about 14 tons per day. THE PROCESS The process, in brief, is as follows: The raw materials are dolomite and ferrosilicon, 75 per cent grade. The dolomite is calcined, the calcine and ferrosilicon are ground and mixed and the mixture is briquetted. The briquets are charged into tubular retorts of chrome-nickel steel set horizontally in a furnace with the open ends projecting outside the front wall. The retorts are then closed and evacuated. Magnesium is liberated according to the reaction 2(MgO, CaO) + Si = 2Mg + 2CaO, SiO2 It is distilled from the charge and condensed on a removable sleeve in the throat of the retort. Sodium and potassium, if present, are also liberated, distilled and condensed on a "sodium condenser" in the end of the retort. At the expiration of the distillation period the retorts are discharged and the cycle of operations is repeated. For the rated daily capacity of ±. tons of magnesium there are required approximately 170 tons of dolomite, equivalent to about 85 tons of calcine, and 16.5 tons of ferrosilicon. The retort residue, a bulky powder which at present is waste, amounts to about 87 tons. CHOOSING THE SITE The investigation to select the location of the plant was conducted by the Research Laboratories of National Lead Co. This work included geologic and economic surveys of a number of districts, examination of dolomite samples by chemical, spectrographic and petrographic methods and large-scale tests of dolomite from several of the more promising localities. In the last-named tests 2-ton samples were put through the ferrosilicon process in the pilot plant of the Canadian National Research Council, under the guidance of Dr. Pidgeon. The conclusions drawn from the investigation, in regard to the quality of dolomite to be used in the ferrosilicon process, were: First, the dolomite should contain not less than 21 per cent MgO

Jan 1, 1944

By J. I. Paige, T. T. Campbell, A. W. Henderson, H. M. Harris

The chlorination of ilmenite concentrates and slags to produce Tic14 suitable for pigment or metal production was investigated by the Bureau of Mines along with the dechlorination of byproduct iron chloride to produce chlorine for recycle and iron oxide., Ilmenite concentrates or slag powders were fed into the bottom of a fluidized coke bed at 1,050º C using chlorine flow rates up to 20 l/min in a 10.2-cm-dim reactor. Tests showed that >95 percent of the various ilmenite concentrates reacted at optimum conditions, and recovery of TiC14 ranged from 95 to 100 percent of stoichiometric. Impurity dusts were removed from the vapors by cyclones and a fiberglass cloth filter. Iron chloride was condensed as a powder with less than 0.4 percent insoluble material. The TiC14 was collected in refrigerated condensers. Iron chloride was dechlorinated at 500º to 550º C by reaction with oxygen in a 16.5-cm-dim reactor using a fluidized bed of Fe2O3. Optimum processing was attained with a FeC13 feed containing 25 wt-pct Fe203 granules treated with 2 wt-pct NaCl catalyst; Under the above conditions, off gas chlorine concentrations of 62 to 90 wt-pct were obtained. During 2- and 3-day tests with technical-grade FeC13, conversion of FeC13 was 94 to 97 percent, chlorine concentrations were 76 to 90 wt-pct, and up to 92 pct of the stoichio- metric Fe203 was removed in the primary reactor discharge. Chlorine

Jan 1, 1976

The effects of process variables such as solution chemistry, flocculent type and dosage, intensity and duration of mixing, and solids type and concentration, on the performance of flocculation/clarification/thickening processes are described. System response is evaluated in terms of the specific effects on floc settling, supernatant clarity and sediment compressibility. The implications of these results with respect to industrial practice are discussed and general guidelines for direct application to plant design and operation are suggested.

Jan 1, 1993

By Large RR

Underlying the 15 million tonne, high grade Hellyer volcanogenic massive sulphide deposit of western Tasmania is an extensive, well developed, and well preserved stringer system. Pervasive alteration of the footwall mafic volcanics occurred as the hydrothermal system initiated. Mineralogical zoning exists within the footwall alteration pipe, with a central siliceous core giving way to zones of chlorite, chlorite-carbonate, sericite-chlorite, and finally sericite-quartz on the margins (stringer envelope zone). However, the alteration morphology and zonation is not symmetrical around the central siliceous core; eastward the alteration zones are steeply dipping and terminate abruptly under the massive sulphide, while westward they extend out under the ore body in a blanket fashion. Geologic evidence indicates that the pervasive alteration started with the development of sericite-quartz which was subsequently overprinted by chlorite and finally quartz-sericite as the hydrothermal system became focused towards the centre of the stringer system.

Jan 1, 1990

By John L. Hill

Cutter roof failure is a specific type of ground control problem which frequently results in massive roof failure. It is a cannon occurrence in coal mines of the Northern Appalachian Coal Sasin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure togain a basis from which to prevent its occurrence and to support such roof when failure does occur. Research conducted in a coal mine of central Pennsylvania has revealed a correlation between the occurrence of clastic dikes and fonation of cutter roof failure. Inmine mapping of ground conditions showed an increase in roof failure in areas of high frequencies of clastic dikes. Rock pressure monitoring around clastic dires registered the greatest amount of roof loading near the inter- section of dikes with the rib. Load cells measurim horizontal pressure changes in the roof indicated that the greitest pressure changes were occurring perpendicular to entry headings when clastic dikes were present. Analysts of rock pressure nwnitiring shows that the roof behaved as two cantilever beams when severed by a clastic dike. Additional roof supports such as trusses and cribbing were found to effectfvelv suooort the roof in areas of clastic dikes and prevent cutter roof iailure. However, there lnethads were only successful when employed shortly after mining.

Jan 1, 1984

It is hypothesised that increasing the number of loading passes will produce a reduced range of truck payload outcomes compared with four-pass loading. The paper provides analysis to support this hypothesis. It is shown that, hypothetically, loading trucks with five or more passes will result in reduced tendency for overloading and reduced confidence interval for truck payloads that increase the confidence level of containing high end payloads within safe and commercially acceptable limits. Furthermore, increased number of passes provides for more precise bucket load spotting and so improves distribution of payloads within truck bodies. Truck-loading issues examined by the paper include: Improvement in life of driveline components and tyres. Generally tyre costs are relatively moderate; but tyres tend to become an increasingly sensitive performance/cost component as truck scale increases; Reduction of site severity fects flowing on to suspensions, truck frames and structural components generally with potential for reduced long-term repair costs; Less physical body damage due to smaller load increments; Reduced risk of non-compliance with payload limitations for safe braking standards; Increase in loading cycle times tend to increase with scale of loading machinery within the limits of a specific type of equipment (ie rope shovels or hydraulic shovels). Production increase with increased bucket capacity is, to a degree, offset by slower loading cycle times. This is particularly pronounced with front-end loaders but tends to be less noticeable with hydraulic excavators/shovels and electric rope shovels. Decrease in loading time, as a proportion of total truck-cycle time as open pits deepen and dump reaches increase. The production and cost benefits of four-pass loading tend to diminish as truck cycle times increase. The paper also discusses the implications for loading-equipment philosophy to satisfy the future needs of the industry. Cost benefits from upscaling tend to diminish as truck scale increases, so increasing management diligence and close monitoring are required to ensure that expected outcomes are realised. These truck-loading issues have been researched to assess the benefits positive or negative) of four-pass loading in practical scenarios. An attempt is made to determine whether four-pass loading is a æmust-haveÆ or merely a æmythÆ.

Jan 1, 2003

By Kenneth K. Humphreys, J. W. Leonard, T. S. Spicer

INTRODUCTION Reasons for Thermal Drying The continuing increase in the percentage of - '/4 in. ( -6.3 mm) coal produced as a result of the increased use of mechanical mining methods has, over the years, tended to shift considerable portions of the work of producing salable coal to the fine coal cleaning section of the preparation

Jan 1, 1979

The Olympic Dam copper-uranium-gold-silver deposit, located approximately 520 km north-northwest of Adelaide, South Australia (Figure 1) was discovered in 1975 by Western Mining Corporation. A joint venture to facilitate development of the deposit was formed in mid-1979 between WMC (51 per cent) and the British Petroleum Group (BP, 49 per cent). Production commenced in 1988, and current annual output from the mining and treatment of 2.2 Mt of ore is approximately 65 000 t of refined copper and 1400 t of uranium oxide. Significant amounts of refined gold and silver are also produced.

Jan 1, 1993

By David Miller

"The biggest concern about using soil mixing is the inability to observe physically the final product, which has led to a lack of confidence about what is in the ground. After all, you can’t see it and you can’t taste it and you can’t smell it, so are you sure it’s soil mixing? In addition, there are variations in techniques, tools and monitoring that have led to additional skepticism and the desire to “elevate” the product. This skepticism is why the industry is so scrutinized even when there are other technologies being used that do not experience nearly the same level of scrutiny. With other techniques, even with a slurry wall, you can see the backfill before it goes into the ground, and drilled piers have careful evaluation of the concrete mix even before placement into and verification of the open hole. Essentially, you get control over the final material. There is less control in soil mixing, and it’s very dependent on in-situ conditions. These factors make it difficult to rely solely upon installation parameters, quality control (QC) and verification tests. At some point, you may need to apply some engineering judgment.Start at the BeginningThe availability of sufficient and accurate geotechnical data (soil type, heterogeneity, shear strength parameters, variability, etc.) is important in establishing the material that will be drilled. This data will also help in determining the proper mix design to achieve the desired soil cement properties. Many factors must be considered when designing the mix and the mixing program, including any debris in the ground, different soil properties and varying moisture contents.Each of the various factors affect the final properties of the soil cement, so it really takes careful planning and evaluation of the mix design through iterations by looking at the soil types and adjusting the mixes. Clay is going to behave very differently than sand in both mixing efficiency and final properties. That is, the presence of clays results in more difficulty in achieving higher strengths and to physically mix the soil and the binder, whereas the presence of sands results in more difficulty controlling the final permeability."

Jan 1, 2017

By C. M. Loeb, T. E. Norman

THE use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent sufficient value to justify thorough studies of the factor sgoverning their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. THE DEVELOPMENT OF A SUITABLE WEAR TEST A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involved the purchase of several hundred tons of balls of a specific type which were then run in one or more ball mills for a period ranging from several months to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was. known that Ellis and his associates1.2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1948

By Eugene F. Poncelet

GLASS squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. EXPERIMENTAL PROCEDURE Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. 1). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2 1/2-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through" of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1944