Search Documents

By A. M. Gaudin, J. G. Morrow

FLOTATION requires the existence of a definite contact angle. This contact angle, the surface tension of the solution, and adsorption at the solid- fluid interface are quantitatively related. Adsorption of dodecylammonium acetate on hematite was measured for a wide range of concentrations of reagent in solution. Similar measurements for quartz have already been made.1 Contact angle measurements were then made on polished surfaces of hematite and of quartz immersed in aqueous dodecylammonium acetate solutions, and a functional relationship was sought between adsorption density at the mineral-solution interface and the contact angle. Finally, the surface tension of the aqueous amine acetate solutions was measured. These data were combined to give an evaluation of the work of adhesion for the three-phase system.

Jan 12, 1954

By P. C. Thakur

Horizontal drilling in coal mines is a relatively new technology. The earliest recorded drilling in the United States was done in 1952 at the Humphrey Mine of Consolidation Coal Company for degasification of coal seams. Spindler and Poundstone experimented with vertical and horizontal holes for eight years. They concluded in 1960 that horizontal drilling in advance of underground mining appeared to offer the most promising prospect (for degasification) but effective and extensive application would be dependent upon the ability to drill long holes, possibly 300-to 600 m, with reasonably precise directional control and within practical cost limits.(1) Mining Research Division of Continental Oil Company, the parent company of Consolidation Coal Company, began a research program in the early 1970's to achieve the above objective. The technology needed to drill nearly 300 m in advance of working faces was developed by 1975 and experiments on advance degasification with such deep holes began in 1976. Preliminary Its of this research have already been published.(2) To date nearly 4500 m of horizontal holes have been drilled for advance degasification and earlier results were reconfirmed. In summary, these are: 1) The greatest impact of these boreholes was felt in the face area where methane concentrations were reduced to nearly 0.3 percent in course of two to three months from original values of nearly 0.95 percent.

Jan 1, 1979

By Nan C. Jensen, Oliver Bowles

"INTRODUCTION Limestone (which consists essentially of calcium carbonate) and dolomite (calcium magnesium carbonate) occur widely in the United States. Their presence is of vast economic importance, because they are used much more extensively than any other form of rock. In 1945, limestone (which, broadly, includes dolomite) was quarried in every State except Delaware, New Hampshire, North Dakota, and Rhode Island, and also in Hawaii and Puerto Rico. Total production (including that used in cement and lime manufacture) exceeded 151,700,000 tons, or 79 percent of the quantity of all kinds of stone sold or used during that year.Important well-known uses of limestone are as concrete aggregate, road material, railroad ballast, for liming the land, for cement manufacture, as riprap for shore protection, harbor work, and spillways at dams, and as building stone.. None of these uses, however, are considered herein. The purpose of this paper is to discuss the industrial and chemical uses that are less widely known and yet are of tremendous importance in a great variety of processing industries. Important examples are dolomite as a refractory furnace lining and limestone as a fluxing agent in blast furnaces, and as a raw material employed in sugar, paper, glass, and alkali manufacture.PRIOR REPORTIn May 1941, the Bureau issued a report 4/ that described these uses in some detail. As new and important developments have taken place during the ensuing years, a revision and representation of the salient features of these uses seem desirable. Asphalt filler and mineral wool uses included in the earlier report are omitted from this paper because they are identified more closely with the highway and building industries, respectively, than with the industrial applications."

May 1, 1947

By R. K. Zipf

Recent scientific studies by researchers at the National Institute for Occupational Safety and Health (NIOSH) and the U.S. Army Corps of Engineers (USACE) presented the worst-case explosion pressures that can develop if a methane-air mixture of a certain composition and dimension accumulates and ignites within a sealed area of a mine. The Mine Safety and Health Administration (MSHA) issued its final rule on sealing of abandoned areas which considers potential explosion pressures and the risk of achieving the necessary conditions. The new MSHA seals regulation has increased the pressure design criteria an order of magnitude beyond the old standard of 140 kPa (20 psi) to 800 kPa (120 psi). However, there still are major knowledge gaps pertaining to seals and sealed areas including: (1) the composition of the sealed area atmosphere and how it changes in time and space, (2) explosion pressures that might actually develop within sealed areas, (3) engineering procedures to follow when designing seals and seal installations, and (4) guidelines to manage the atmosphere within sealed areas with monitoring or inertization. NIOSH has initiated a seals research program with collaborators from Safety in Mines Testing and Research Station (SIMTARS) in Australia, West Virginia University (WVU), the Naval Research Laboratory (NRL), and USACE. Highlights of progress so far include: (1) construction of a gas explosion tube at Lake Lynn Laboratory for studying large methane-air explosions, (2) computer simulation of the fluid dynamics of high pressure methane-air explosions, (3) development of seal analysis methods considering construction materials, reinforcement and the seal foundation, and (4) development and testing of innovative seal designs that utilize inexpensive, readily-available rock rubble to resist high explosion pressures. NIOSH researchers aim to provide sound engineering guidelines to better address the new MSHA seal regulations. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Xun Zhang, ZhiLong ZHAO, Lifeng Zhang, Huiqing Tang

A two-dimensional gas-solid model has been developed for examination of the blast furnace (BF) performance under hot charge operation. Simulation conditions were obtained from the actual operation conditions of the BF with inner volume of 2500 m3 and molten iron output of 6250 ton hot metal (THM) per day. The simulation results indicate that hot charge operation could change the thermal state of the BF in the region above cohesive zone (CZ) and has little influence on the thermal state of CZ zone and the region below CZ; it could intensify both the indirect reduction of the ore and the gasification of the coke in the region above the CZ. The optimum temperature for hot charge operation is 750 K, under which, a coke rate reduction of 25 kg/THM could be obtained.

Mar 1, 2017

By C. E. McFarland, N. W. Kirshenbaum

Cortez Gold Mines is located about 75 miles southwest of Elko, NV. Activity in the mining district dates from 1862. The current operation developed from a 1963 joint venture of Webb Resources, The Bunker Hill Company, Vernon F. Taylor, Jr., and American Exploration & Mining Co. Three years later, the USGS discovered gold on the property following a regional geochemical survey. Drilling in 1966 and 1967 identified 3.4 million st of oxide ore grading 0.28 oz Au/st, and a 1700 st/day countercurrent decantation mill was commissioned in 1969. Heap leaching started in 1971 on low grade ore and continues to the present. The mill was shut down in 1976 following exhaustion of known oxide reserves. Mobile equipment was sold and the proceeds committed to local exploration. In 1980, a new plan of operations was developed starting with existing low grade and newly discovered mill ore. The mill resumed operations in 1981 and has been operating to date. A series of metallurgical innovations, culminating in the commissioning of a new fluid bed roaster in the summer of 1990, has enabled treatment of a series of increasingly refractory ores. Current partners in the venture are Kennecott Corporation, Vernon F. Taylor, Jr., and Placer Dome U.S. Inc., manager of the operation. Idaho Mining Corp. holds a 7.5% carried interest.

Jan 1, 1992

By C. J. Im

As market conditions become more competitive, U.S. coal producers are faced with the increasing need to find methods of lowering production costs in their operations. One area worthy of investigation is the additional recovery of fine coal that is normally discarded in the preparation plant waste stream. United Coal Company is currently assessing the capability of the Deister Flotaire, a new application of a column flotation cell, to recover additional, saleable coal from preparation plant waste. This paper presents the technical data obtained to date. Work with a 0.76 m (30 inch) diameter cell installed in a plant shows considerable coal recovery is possible from a nominal 0.595 run (28 mesh) X 0 refuse stream.

Jan 1, 1986

By Grano S. R, Lauder D. W

Investigations on the oxidation behaviour of chalcocite and its rejuvenation by hydrogen sulphide ion have been undertaken. Chalcocite oxidation was measured using X-ray photoelectron spectroscopy (XPS), zeta-potential and by dissolution in et

Jan 1, 1997

By Kot F. Unrug

The shale response to moisture changes and the major finding of the appropriate research concerning this subject are briefly reported in this paper. Also described are mine ambient atmospheric conditions which are responsible for moisture changes in mines. The need for a quantitative measure of the weathering potential of roof. rock is demonstrated in relation to its influence on safety and the potential for increasing the cost of mine operations. The weatherability test presented in this paper has been developed and used in many mines. It imitates the natural process in a mine by subjecting the rock sample to alternating wet and dry cycles. The natural changes are thus accelerated, but are similar to the natural conditions to which the surrounding excavation rock will be exposed. The measure of the weatherability index is the percentage of the initial sample mass remaining after the test as the largest fragment of the sample. Thus, the index changes, from 100% for rock affected by moisture changes which disintegrates completely, to 0% for rock totally unaffected. In this paper, the apparatus and testing procedures are described. Also presented are examples of test results. with a discussion of the design implication to he considered by mine planners.

Jan 1, 1997

Mineral deposits in New Zealand whose origin can be ascribed to primary magmatic segregations are associated with mafic-ultra- mafic complexes related to two orogenic episodes which took place during Paleozoic and Mesozoic times. These mafic-ultramafic complexes are essentially of two types. One is ophiolitic and has podiform chromite mineralisation presumably formed below a spreading ridge. The other type occurs as intraplate layered intrusions in which Fe-Cu-Ni sulphides and Fe- Ti-V oxides have formed as a result of liquid immiscibility with the host magma, and have subsequently accumulated by gravity means. Generalised descriptions are given for some deposits in NW Nelson, Fiordland and Marlborough districts.

Jan 1, 1980

By Neill A. O, Worth I, O&apos

The formation of Kalgoorlie Consolidated Gold \lincs 1't% Ltd hati pla,xd all the major the gold producing areas adjacent to the city of Kalgoorlie/Boulder under one management, enabling the development of the 'Super Pit'. This has facilitated the economic optimisation of the resource. Optimisation has been achieved by the timely collection and presentation of data and the use of these data to reduce costs and improve planning procedures.In particular the following issues have been addressed:ò the reduction of the impact of the mining activity on the adjacent urban population centre,ò implementation of safety procedures for mining through underground voids,ò the determination of the optimum bench height and mining method for ore production benches and blast design. This system is fundamentally based on maintaining a high degree of selectivity while achieving a balance of relatively low unit operating costs,ò assessment of the comparable benefits of contractor versus owner operated earth moving equipment, andò the development of effective ore body models, production reconciliation and the long term mine planning procedures to facilitate effective strategic planning.

Jan 1, 1993

Your committee's secretary submits the following report, or summary, to the- members of the committee, in an endeavor to lay before them a general review of the information so far received and also his own knowledge .of the work as carried on at a number of plants, this being done in part to secure further information and suggestions from members and lead to a more effective means of furthering the work of the committee. It is suggested that more detailed data be compiled regarding engineering features involved, and that papers be contributed which will deal with the safeguarding of underground electrical installations. There are few operating companies which have not started a more or less systematic campaign to safeguard their employees from accidental injuries and unhealthful surroundings, but a great deal is to be gained by experience. All may welcome the advice and cooperation of those who have been actively engaged in the work and have demonstrated the results obtainable by organized effort, and it is, therefore, exceedingly gratifying to note the ready assistance and hearty cooperation rendered by the companies that may be truly termed pioneers in the movement. No solution of the safety problem is to be found in a strict standardization of methods, rules or devices, as' the various mining, milling and metallurgical practices present too' many conditions differing broadly in general principles, but some standard system embodying principles, already proven to be efficient should be created, which may be modified or elaborated to meet specific requirements of each individual. company, or to fit working conditions as they exist in the various mining camps throughout the country. An industrial plant is -primarily a business undertaking, therefore the economic side-of a safety or welfare campaign is of importance. Many small operators have been deterred from undertaking the work by their belief that it involved an expense beyond their means, and one that could not be counterbalanced by greater efficiency or saving along other lines. This idea is generally clue to a lack of knowledge of the actual costs of such work, and of the results secured by judicious selection of a method commensurate with the. size and nature of the opera-

Jan 1, 1917

By D. N. Cleaver

Like other influence function methods, the SWIFT subsidence prediction program, developed within the Mineral Resources Engineering Department at the University of Nottingham, requires calibration to regional data in order to produce accurate predictions of ground movements. Previously, this software had been solely calibrated to give results consistent with the Subsidence Engineer's Handbook (NCB, 1975). This approach was satisfactory for the majority of cases based in the United Kingdom, upon which the calibration was based. However, in certain circumstances within the UK and, almost always, in overseas case studies, the predictions did not correspond to observed patterns of ground movement. Therefore, in order that SWIFT, and other subsidence prediction packages, can be considered more universal, an improved and adaptable method of regional calibration must be incorporated. This paper describes the analysis of a large database of case histories from the UK industry and international publications. Observed maximum subsidence, mining geometry and Geological Index for several hundred cases have been statistically analysed in terms of developing prediction models. The models developed can more accurately predict maximum subsidence than previously used systems but also, are capable of indicating the likely range of prediction error to a certain degree of probability. Finally, the paper illustrates how this statistical approach can be incorporated as a calibration system for the influence function program, SWIFT.

Jan 1, 1995

By J. E. JR. Johnson

AT the Cleveland meeting of the Institute in October, 1912, I had the honor to present a paper outlining the conditions surrounding the charcoal iron industry, and giving some of the results of an investigation started about three years ago for the purpose of determining the reason for the poor reputation of the Lake Superior charcoal irons as compared with the Southern and Eastern irons. In that paper I explained the effect of high carbon on quality, and tried to make clear that that paper was a preliminary one, as we felt convinced that we should eventually discover other factors affecting quality. The progress of the investigation has brought out facts that seem to us of the utmost importance practically and theoretically, and the purpose of the present paper is to present these facts with the proofs which seem to us to establish them. The closing year of the nineteenth century saw the publication of the first definite and connected statement of the relationship between the cast irons and the steels.' The metallurgical world was ready to accept the fundamental unity of these two series, acceptance being greatly hastened by Professor Howe's classic paper, The Constitution of Cast Iron, presented at the Richmond meeting of the Institute, February, 1901.

Jan 1, 1914

By John A. Meech

"Oleic acid flotation of Mount Wright thickener underflow tailing material has been shown to be capable of increasing plant recovery by 3%. High levels of oleic acid addition (1.5 kg/t) are required, which limit the economic practicality of the system at this time. Nevertheless, from a technical viewpoint, the process is stable with respect to extreme fluctuations in oleic acid requirements, pulp pH and pulp temperature. Methods to reduce the average consumption of oleic acid need to be found. One technique that merits further testwork uses the ""piggy-back"" principle to float hematite fines with coarsegrained hematite particles.IntroductionWith most large-scale iron mining operations treating specular hematite ores, flotation is not often conside red a necessary processing step. The bulk of the iron minerals can be concentrated by gravity techniques and the generation of fines can be minimized because of the course- grained nature of the mineralization. Nevertheless, production of some fine material is unavoidable, and recovery of iron from this fraction by spirals is poor (10-30%).When the proportion of the iron in these fines becomes excessive, alternative methods to conventional spirals are considered(11), Many of the techniques that have been developed suffer from either poor recovery (e.g. the Reichert cones at 36010 recovery)(11) or low throughput rates (e.g. wet highintensity magnetic separation)(12), Flotation is often passed over because of excessive reagent costs, pollution problems and/or balling difficulties from the reagents used.However, of all the processes available, flotation can yield high recoveries (60-90%) at reasonable throughput rates with excellent process control features (reagent addition and/or cell level). The key parameter is reagent cost.This paper describes testwork on the use of oleic acid to float hematite from the fine fractions of the Mount Wright concentrator tailing. The concentrate product from this plant is directly shipped, so no balling problems exist. As well, oleic acid may be considered a lesser pollution hazard than many of the cationic collectors used in other iron ore flotation systems. A reduction in fine hematite slimes discharged as tailing into lakes may also reduce environmental damage."

Jan 1, 1981

By Tateo Usui

In the course of carbonization of coal under a rising temperature condition, volatile matter (V.M.) is released. The kind and amount of V.M. released depend on the kind of coal. Components of V.M. are tar, hydrocarbons (CH4, C2H4, C2H6, C3H8), CO, CO2 and H2, which are released in this order as a function of carbonization temperature. When the carbonization of coal under a rising temperature condition is interrupted at a certain temperature, TC, max, semi-coal-char with residual V.M. is obtained. If some optimum interruption-temperature is chosen, small but most suitable amount of V.M., namely H2, is retained. When the semi-coal-char thus obtained is heated again under the same rising temperature conditions but up to more than TC, max (1), the residual V.M. is released from just around TC, max (1). We propose novel iron ore agglomerate bearing such semi-coal-char with some strength. While simple iron ore agglomerate bearing coal char will start the reduction reaction as solid-solid reaction at somewhat higher temperature, the proposed one will start the reduction reaction as gas-solid reaction at somewhat lower temperature but a little higher than TC, max. Samples of semi-coal-char and novel iron ore agglomerate bearing such semi-coal-char have been prepared and evaluated.

Jan 1, 2006

By Russell Levens

A strategy for prioritizing mining health and safety research by evaluating the potential for risk reduction through interventions is proposed. Mining has one of the highest incidence rates of injury and disease found in major industries. The main premise of this paper is that often the best opportunities to reduce these rates are not revealed by retrospective analysis of injury and illness data. Instead, a proactive approach is needed that accounts for risks to specific hazards that can be abated by engineering or behavioral interventions. The process proposed here begins with development of prospective interventions. The degree of reduction in risk to be expected from an intervention then is determined from statistics on the mining worker population, the expected degree of success of the intervention, and the expected change in the severity of injuries resulting from the intervention. Three disparate mining health and safety concerns are presented to demonstrate common problems in assessing risks of injury and illness and describe additional data needs. Information on events preceding injuries and illnesses and more detailed demographic data on the mining work force are needed to analyze injury and illness data more precisely. Detailed information on exposure to specific hazards is necessary to evaluate the potential for an intervention to reduce risk of injury or illness.

By Thomas V. Mullen

Some 146 kt (4.69 billion oz) of gold have been mined throughout history. Of this, 70% has been mined in this century alone, with 17% produced from 1985 through 1996 (Fig. 1 and Table 1). Until the mid-19th century, placers were the chief source of gold. Advancements in mining, metallurgy and geological thinking have resulted in underground mining (first of veins plus stockworks and later of Rand-type deposits) becoming the principal source of gold. With the demise of the South African deposits and the move towards lower grade ores, the primary source of gold will be from disseminated deposits exploited through large, open-pit mines. For the past 200 years, there has been a fairly constant ratio of about 31 g (1 oz) of gold to each person alive. If this ratio is to be maintained, annual gold production will have to rise from about 2.3 kt/a (73.9 million oz/year) to more than 3.1 kt/a (99.7 million oz/year) by the year 2000. To effect this increase, an unforeseen breakthrough in exploration or metallurgy is needed. Barring this, there will be pressure for an increase in the price of gold. This article traces the historical production of gold from 4000 B.C. - the earliest record of gold mining - to today and relates this 6,000-year record to advances in geological thinking, mining engineering and extractive metallurgy. It also proposes that man's thirst for gold, reflected in the price he will pay for gold, and his ability to find, mine and refine gold have combined to effect an equilibrium based loosely on the historical ratio of 31 g (1 oz) of cumulative gold production per each man or woman alive.

Jan 1, 1998

By Jack A. Simon, M. E. Hopkins

Coal is defined as a combustible rock that originated in the accumulation and physical and chemical alteration of vegetation. Coal can be ignited and burned like the wood that was man's earliest fuel, but coal gives more heat than the same amount of wood and has many industrial uses. Unlike wood, coal is not generally found on the surface of the ground but is mined from the solid rock of the earth. Before taking up the occurrence, formation, and the unique character of coal in the rock sequence, let us briefly consider the general character of all rocks in the crust of the earth. Relatively little is known about the very earliest history of the earth, although a number of logical theories have been developed. Manned exploration of the moon and the rocks returned to earth continue to provide some answers to questions concerning the earth's origin and history. The period of earth history with which we concern ourselves here begins after great areas of water had evolved on earth and substantial land areas of once molten (igneous) rock existed. Weathering and other processes that attacked the surface of the rocks reduced them to small particles. Water provided by rainfall transported this material, ultimately, to large bodies of water where it was deposited. Thus was initiated the geologic sequence of sedimentary rocks that lie above the once molten igneous rocks. The crust and upper mantle of the earth are made up of several large plates along which differential movement (primarily horizontal) takes place. Such movements, although small, are occurring today. These horizontal movements are accompanied by vertical movements causing important changes in the relative position of the continents and oceans. Low-lying coastal swamps with favorable climates are ideal locations for coal accumulation and burial by river-borne sediments, and large areas

Jan 1, 1981

By T. Oberthür

The Great Dyke of Zimbabwe constitutes the world&apos;s second largest reserve of platinum group elements (PGE) after the Bushveld Complex in neighbouring South Africa. Within the Great Dyke, economic concentrations of PGE are restricted to sulphide disseminations of the Main Sulphide Zone (MSZ), which are currently mined at the Ngezi, Unki, and Mimosa mines. Near-surface oxidized MSZ ores have a large potential. Their total resources are in the range of 160-250 Mt; however, all previous attempts to extract the PGE from this ore type have proved uneconomic due to low PGE recoveries (<< 50 per cent) achieved by conventional metallurgical methods. Within the ores of pristine, sulphide-bearing MSZ, the PGE are bimodally distributed. Platinum occurs mainly in the form of discrete platinum group mineral (PGM) grains (mainly bismuthotellurides, sulphides, and arsenides), whereas approximately 80 per cent of the Pd (and some Rh) is hosted in pentlandite. Within the oxidized MSZ ores, the PGE are polymodally distributed. Whereas the arsenide- and sulphide-PGMs that make up approximately 25 per cent of the original Pt content of the ore largely remain stable (relict PGMs), the remaining PGMs are disintegrated. The base metal sulphides are destroyed, partly releasing their base metal and PGE contents, and are replaced by iron oxides or hydroxides. Unspecified amounts of the PGE are redistributed and either form secondary PGMs, are found in chemically and mineralogically ill-defined (Pt/Pd) -oxides or hydroxides, or in iron-hydroxides, Mn-Co-hydroxides, and in secondary silicates. The problematic processing of oxidized MSZ ores is attributable to their complex nature and polymodal distribution of the PGE, prohibiting a significant upgrading of the ores by conventional metallurgical methods. Therefore, only bulk leaching methods are viable for ore treatment, and novel metallurgical methods have to be developed for the processing of these ores. Our ongoing work aims at locating the PGE in their mineralogical form in order to understand the mineralogical balance of the PGE in the ores and thereby facilitate the evaluation of metallurgical options for their recovery. A short overview on options and recent advances regarding the recovery of the PGE from oxidized ores is given.

Jan 1, 2013