Search Documents

By Waldemar Dyrssen

I CANNOT agree with the results obtained by the committee. The gas obtained per pound of coal is too high in calorific value and the amount of gas is too large. It should require about 190 cu. ft. of oxygen per 1000 cu. ft. of gas and not 75.14 cu. ft. as is given on page 35 of the report, or about 2.5 as much. Calculating the calorific value per pound of coal from the coal analysis given on page 34, according to Dulong's formula, the gross and net calorific heat are about 12,890 and 12,430 B.t.u., respectively, which is about 18,600 and 17,900 B.t.u., respectively, per pound of carbon in the coal. This is an unusually high figure, as ordinary bituminous coal has less than 18,000 gross B.t.u. per pound of carbon. Assuming, however, that the calorific values calculated are correct, the following results are obtained. On page 35, the net calorific heat in the gas per pound of coal is given as 12,856 B.t.u. and calculation for the gross value shows it to be about 13,950; in other words, the gas contains (13,950 - 12,890) ÷ 12,890 = 8.2 per cent. more heat than the coal on a gross basis and (12,856 - 12,430) ÷ 12,430 = 3.4 per cent. more on a net basis. The calculated amount of carbon in this gas per pound of coal gasified is about 0.688 lb., or nearly the same as in the coal (0.6972) and the gross and net calorific heat per pound of carbon in the gas are 20,300 and 18,710 B.t.u. which are 9.1 and 4.5 per cent. more than for the carbon in the coal. These calculations show that the results given in the report cannot be correct. There must always be some heat losses in the gasification of coal, in radiation from the producer, and in sensible heat in the gas; there must be some loss of carbon in ashes and in soot, and there are always tarry vapors in the gases that are condensed and do not appear in the fixed gases. From the excessive heat in gas per pound of carbon contained therein, it can also be concluded that the percentage of hydrogen in the gas is too high, from which it follows that the moisture decomposed is too high and that more free oxygen must be used.

Jan 11, 1924

By R. P. Adams

Because of the extreme interest in materials with high melting temperatures and the advantages offered over the powder route for making high-density material, arc-melting and centrifugal-casting methods were investigated for preparing shapes of hafnium carbide with and without excess carbon. Highly satisfactory equipment was constructed and efficient operating procedures were established. Also, methods for preparing consumable electrodes and shrink-tolerant graphite molds were developed. Although crack-free hafnium carbide (6.3 weight-percent carbon) shapes were not made, coherent castings containing 9 to 13.5 weight-percent carbon were produced; the same compositions were shown to be resistant to thermal shock. Selected physical and chemical tests were performed on castings chosen for investigation by chemical and nondestructive inspection techniques. Electrical conductivity and thermal expansion measurements were made. Measurable oxidation of all the compositions studied was observed to start between 500° and 600° C. Attack by nitrogen, however, did not occur until temperatures exceeded 2,000° C. A linear relationship of the logarithm of the diamond pyramid hardness to the temperature was noted. Considerable scatter of the bend-rupture strengths at room temperature and of the tensile strengths up to 2,000° C was found. However, at the latter temperature and above, a definite relationship of strength to temperature was observed and some ductility was noted.

Jan 1, 1968

By Claudia Gasparrini

"Factors affecting the extraction of gold are of a mineralogical nature. Knowledge of the mineralogy of the ore or metallurgical product to be treated, if appropriately combined with the metallurgical test work, may improve gold recoveries. .This paper outlines the mineralogical techniques f or the study of gold ores and metallurgical products and describes the gold mineralogy in relation to its metallurgy. An effective plan for studying refractory and other difficult ores, combining metallurgical test work, chemical analysis and mineralogy and capable of giving positive results over relatively short periods of time, is suggested.IntroductionFactors affecting gold recoveries are of a mineralogical nature and include (i) the gold-bearing minerals, (ii) their grain size and, particularly where the grain size is very fine (10 microns in diameter and less), (iii) their host minerals and (iv) the association these form with the gold-bearing minerals.Mineralogical studies of gold ores and metallurgical products containing gold in economic amounts (today down to 1/10 of one ounce per tonne or 2.84 ppm) are difficult and time consuming. Mostly because of such reason, metallurgical testing (test work) is usually done simply by trial and error without understanding the causes for failure or success.Mineralogical studies, if appropriately conducted and combined with the test work, provide an efficient mean s of improving recoveries through the understanding of gold losses derived from the use of the wrong technique for separation. The information they provide is therefore the first step in the development of recovery techniques, for those ores where the test work alone failed to produce positive results."

Jan 1, 1983

By Tom C. Palangio

Commercially available online particle size analyzers (OPSA) are in their third decade of development (Palangio, T.C., 1985), (Franklin, J. A., Maerz, N.H., 1987), (Maerz, N.H., Franklin, J.A., and Coursen, D.L., 1987). The installed base of operating analyzer numbers is in the hundreds. This paper takes a look at five critically important relationships that users have discovered through the use of OPSA systems. The two key attributes of these systems are: 1) consistency and, 2) historical context compared with traditional practices.

Jan 1, 2016

By T. G. Carter

"Tremendous progress has been made in recent years towards developing computational tools that allow ready solution of most common rock engineering problems, with amongst the most advanced of the tools focusing on evaluating engineered openings within Synthetic Rock Masses. These new codes have the potential to allow much more realistic design, but they must not be used without careful calibration – prior to – during and – post completion of any modelling. This paper explores some of the pitfalls of inadequate data collection and suggests more emphasis be given to calibration. Guidelines for minimum levels of parameter data are suggested for improving application of basic to sophisticated modelling codes.INTRODUCTION & BACKGROUNDTremendous progress has been made in recent years towards developing computational tools that allow ready solution of most common rock engineering problems. The degree of sophistication now possible with some of the available codes allows one to tackle extremely complex problems that were not thought tractable even a decade ago. Indeed, generation of synthetic numerical rock masses, based on discrete fracture network representations that closely mimic actual rock mass conditions, such as are shown in Figure 1, is today relatively straightforward, and not as user-challenging as employing state-of-the-art codes of even a few decades ago. This is largely because major improvements in computer graphics and in availability of ready-made user-friendly input-output interfaces have paralleled development of these new codes, now in some cases outpacing actual new analytical/procedure developments. This is something of a reversal from the first few decades of DOS-based rock engineering computational experience, when only rudimentary graphics were available and user-friendly input-output interfaces were virtually non-existent."

Jan 1, 2015

By James A. Robertson

"This paper is the result of a continuing investigation begun in 1953 by government geologists and mining companies. Previous work is reviewed and the development of several stratigraphic nomenclatures and correlation schemes is traced, culminating with the interim report of the Federal-Provincial Committee on Huronian Stratigraphy formed in 1966.The stratigraphy, structure and correlation of the Huronian rocks of the Blind River area and the region between Sault Ste. Marie and Sudbury are reviewed. The area is underlain by three Precambrian units: (1) the Archean greenstones and granites, (2) the Huronian sedimentary and volcanic rocks and (3) the post-Huronian intrusive rocks. The Huronian rocks, largely quartzite and conglomerate with greywackes, argillites and carbonates, were laid down in shallow water transgressing over the eroded Archean basement. Thickness and facies changes indicate a northwesterly source, northerly overlap and deposition controlled by basement topography. Polymictic conglomerates, occurring at least at three horizons, represent tillites and are associated with varvites with dropped clasts. These are best developed in the Gowganda formation, which varies from a continental glacial environment in the north to a marine glacial environment in the southeast.There were at least three phases of post-Huronian igneous activity, probably related to several periods or phases of late Precambrian deformation and metamorphism: (1) sills of Nipissing diabase and rather younger diabase dikes; (2) the Cutler Granite and Croker Island Complex; and (3) dikes of Keweenawan olivine diabase.Copper mineralization is associated with the Nipissing diabase. The uranium ores are found in pyritic quartz-pebble conglomerate near the Huronian Archean unconformity, particularly in ancient valleys; they are considered to be placer deposits modified by later events. Uranium production from the Blind River camp to the end of 1966 was 128,160,096 pounds U308 valued at $1,203,840,848 derived from 56,077,179 tons of ore grading 0.11 per cent U308.Within the Blind River and adjacent areas, future discoveries will probably be the result of costly systematic deep-drilling programs accompanied by detailed geologic studies of the type carried out by oil companies and probably computer-oriented."

Jan 1, 1969

By H. W. Graham

[ ] Even though we have a small audience, I am sure there are some here who are interested in sponge iron. It is a large subject, with a lot of economic interest, and one that will continue to grow in importance as the years go by and as the conditions that urge action in that direction increase. The authors have chosen to deal in this paper with one particular narrow phase of a long program of work by the Bureau of Mines. Before asking for any general discussion, I would myself like to ask Mr. Buehl if he would tell us just a little bit about the mechanism of discharge and the form in which the material was discharged; that is, when dolomite is added, what happens to the dolomite? R. C. Buehl (author's reply)-You are interested in the equipment that was used? H. W. GRAHAM-No, just the product. R. C. Buehl-The product was in granular form, of a shape very similar to that of the ore used. Using minus 10-mesh ore, the product is essentially minus 10-mesh, mixed with the coal and dolomite. It is then passed through a belt type of magnetic separator, which picks up the magnetic iron and allows the dolomite and coal to fall off. If the coal is sufficiently valuable, it can be separated from the dolomite and, provided the coal has a sufficiently low ash content, it can be reused. For instance, if a low-ash reducing agent like petroleum coke is used, it can be reused until all the carbon is consumed. H. W. Graham-That clears the point for me. I was not quite sure whether the experi-

Jan 1, 1947

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By Robert Roby

The Mouat copper-nickel deposit in Stillwater County, south-central Montana, was examined by Paul T. Allsman, an engineer of the Bureau of Mines, in 1939. Because of the strategic importance of nickel, a project was executed by John East, Jr., J. J. Naughton, and E. W. Newman, engineers of the Bureau, to further delimit some of the copper-nickel sulfide-bearing bodies that had been discovered by the Anaconda Copper Mining. Co. in 1937 and to investigate the central part of the deposit, which had not been drilled previously. This report is based largely upon the results of the. Bureau of Mines investigation and the results of exploration by the Anaconda Copper Mining Co. In addition, a brief description is given of some other copper-nickel sulfide-bearing deposits along tho Stillwater Complex.

Jan 1, 1949

University of Alabama-University, Alabama, Mining and Metallurgical Society, James W Stewart University of Alaska-College, Alaska, Mining Society of the University of Alaska, Jack R Hoskins University of Arizona-Tucson, Arizona, Miners Society, A E Gorum Birmingham-Southern College-Birmingham, Alabama, Pick and Hammer Club, Daniel D Arden University of British Columbia-Vancouver, British Columbia, G M Dawson Club, A Gunning University of California-Berkeley, California, Mineral Technology Association, Bernard York Carnegie Institute of Technology-Pittsburgh, Pennsylvania, The Metals Club, Gerhard Derge Case Institute of Technology-Cleveland, Ohio, Case Metallurgical Engineering Society, Robert F Hehemann City College of New York-New York, New York, CCNY Student Chapter AIME, Daniel T O'Connell

Jan 1, 1955

By Edward Jeffrey

THE use of coke in metallurgy, to any important degree, dates from the middle of the 18th century. Its utilization came most opportunely for European civilization. The forests of Europe, except in the most remote and inaccessible regions, had been largely fed, in the form of charcoal, into the smelting furnaces. For a hundred years-the middle of the 17th to the middle of the 18th century-there was a stationary condition of population corresponding to the exhaustion of European forests. This situation, which was particularly evident in Great Britain, was due to the fact that the forests had been depleted and the practical utilization of coke had not begun. The coking industry is essential for our metallurgical industries, which in turn are basal to healthy economic progress. But coke is of great importance, not only on its own account, but for its byproducts, which enter fundamentally into all the arts of peace and war. The dyestuff industry and the manufacture of explosives are intimately connected with one another, as was shown by the recent war. The subject of coking coal, therefore, is well worthy the serious attention both of practical industry and the scientific investigator. The most valuable coking coals, from the metallurgical standpoint, are derived from the coals of highest ranks. Coals, for example, that have a carbon ratio of from 70 to 80 per cent. yield the most valuable coke for the blast furnace. The difficulty of investigating these coals, however, is great, for they are rather friable and delicate and possess a high carbon content, which makes them difficult to manipulate. They present, on account of their high carbon content, a considerable degree of opacity when examined, in thin sections, under the microscope. The tenderness of structure and blackness of such high-grade coking coals as those of Connellsville and the Pocahontas region make them extremely difficult to investigate.

Jan 1, 1925

INTRODUCTION From its beginnings in the first decade of this century, flotation has gradually moved to a predominant role in mineral separation. There are several reasons for this, the continuing trend toward treat¬ment of lower-grade and more finely disseminated ores being the major one. Not only has this been true for sulfide ores to which the process was first applied commercially, but also for most nonsulfide ores as well. A second factor has been the broad applicability of the process with respect to particle size; it is effective from 8 to 10 mesh to below 10m. Finally, more so than for any other separation process, flotation has almost no limitations in separating minerals. Gravity, magnetic, or electrostatic processes are either applicable to particular minerals, or to a restricted number of mineral combinations. Flotation, on the other hand, can utilize the wide range of surface chemical differences among minerals, and an equally wide range of reagents. The recent availability of selective flocculation capabilities on a commercial scale as an adjunct to flotation should remove one of the limitations to the process in the very fine particle range. History Although flotation was anticipated in a 19th century patent to Haynes, its first significant industrial uses were in the early 20th century in Australia. According to Hoover,' the Pottter-Del-prat pro¬cess had a "measure of success" at Broken Hill's Block 14 mine in 1905-1906, and was definitely successful at the BHP Mine, where it produced 80,000 tpy of zinc concentrates. Both the Mineral Separa¬tion and the Elmore processes had early trials in Australia also, with both successes and failures. The first application in the United States was in 1911, when the Hyde process was used by the Butte and Superior Copper Co. on a zinc ore in Montana. By 1916 Hoover could list 46 applications to copper, lead, and zinc ores, mainly in the United States. Ten years later Taggart2 listed almost a thousand patents covering processes and reagents which with few exceptions laid the foundations for modern practice. Included were: sulfidizing of oxides; leach-precip¬itation-flotation; cyanides, sulfites, sulfides, and oxidants for selective depression of sulfides; starch, tannin, and glue as depressants; and xanthates, dithiophosphates, and oleic acid as collectors. Within an¬other 20 years, all of these were in commercial use along with amines for floating silica from phosphates, and synthetic frothers were com¬peting with pine oil and cresylic acid. Flotation machine development followed a different course. Of the 170 patents listed by Taggart in 1927,1 those incorporating film and oil flotation-about a third of the total-were no longer then

Jan 1, 1985

By P. R. Jones

A computer program was written for the design of a shell and tube type heat exchanger on a price optimum basis. The program was designed to meet the following requirements: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; and (4) no change in phase. Price optimum design was obtained for four standard tube sizes and standard pitch. Pressure drop both inside and outside were computed and the nearest standard shells having at least the required area were listed. With this information, the estimator can select the heat exchanger best suited for the need. The program was made adaptable to various fluids and to various tube sizes and spacing by reading in much of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1967

By S. Srinivasan, R. Coté

"India is undergoing a massive electrification program using local coal to provide fuel for thermal generating plants. The Rajmahal mine in northern Bihar is scheduled to produce coal at the rate of 10 million tonnes per year by the end ofa sixty six month contract with MET-CHEM Canada Inc. for mine development. In order to control maintenance performance and warehouse inventory MET-CHEM is installing some proven computer-controlled programs and will provide extensive training to ensure that the systems are properly used. The programs are Maintenance Planning and Control System (MPCS) and Materials Management System (MMS), both of which were developed and used by Quebec Cartier Mining Company at its iron ore mine in northern Quebec. In addition, a Predictive Maintenance Program (PMP) using vibration analysis will be introduced . This paper discusses the three systems.IntroductionIndia is currently undergoing a massive countrywide industrialization and electrification program. Most of the power will be supplied by coal-fired thermal electric plants.One of the mines being developed as part of the over-all program is the Rajmahal Open Cast Coal project in the Godda District of Bihar, approximately 270 km north , and slightly west of Calcutta.The project is based on an agreement signed in January, 1989 between two government organizations - Canadian Commercial Corporation (Ccq and Coal India Limited (CIL). MET-CHEM Canada Inc. (MET-CHEM), an international consulting engineering organization which has worked in India since 1976, is CCCs Canadian executing agency for the project. METCHEM was the engineer-constructor and mining associate for the development of the 7.5 mtpy Kudremukh Iron Ore Project. This US$430 million project was completed on schedule and under the original budget estimate. The Rajmahal deposit is the responsibility of Eastern Coalfields Limited (ECL), a subsidiary of CIL. The project is to produce coal at the rate of 10.5 million tonnes per year in 1994."

Jan 1, 1991

By Robert E. Hershey

1. The investigation shows that the Sewanee coal bed is the most important bed in Grundy County arid is the only bed that has had any sustained production. There is no production, at the present time, from any of the other coal beds in the county. The Richland (Lower Sewanee or Coke Oven) coal bed has been prospected but has never been developed extensively. The Angel coal bed has been worked to a very small extent near Beersheba Springs, Tenn., for local consumption. The Battle Creek coal bed has been worked sporadically near Monteagle, Tenn. 2. Known measured and indicated reserves in the Sewaneee coal bed, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 15 millon short tons as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas in the bed were omitted from the estimate where available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By O. R. Wagner, R. O. Leach

Immiscible displacement tests were performed in a consolidated sandstone core over the interfacial tension range from less thdn 0.01 to 5 dynes/cm to better define how interfacial tension (IFTJ reduction can lead to increased oil recovery. Data obtained were displacement efficiency at breakthbrough vs IFT for both drainage and imbibition conditions. These tests simulate water flooding under oil-wet and water-wet conditions, respectively. Results of the study have shown that displacement efficiency under both oil-wet and water-wet conditions can be markedly improved by a sufficient reduction in IFT. In the particular porous media used and for the low pressure gradients employed, the IFT must be reduced to a value less than about 0.07 dynes/cm to achieve increased recovery at the time of breakthrough of the injected phase. Below 0.07 dynes /cm, further small reductions in IFT result in large increases in displacement efficiency. Observed increases in recovery were obtained at pressure gradients which are well below those which can exist in the interwell area of a reservoir under water flood. The effect of pressure gradient on recovery is discussed. INTRODUCTION A residual oil saturation remains in rock which has been water flooded because, under usual reservoir conditions, the driving force which can be generated is inadequate to expel oil trapped by capillary forces. Since these capillary forces can be reduced by reducing the IFT a frequently studied method of increasing oil recovery has been the use of surfactants to reduce the water-oil interfacial tension. Mungan l observed improved recovery in both water-wet and oil-wet systems at 1.1 dyne /cm IFT, finding that the amount of improvement was greater in oil-wet systems. Moore and Blum,2 working with visual flow cell micro-models, con- cluded that recovery cannot be improved in water-wet systems by injecting surfactant solutions. They calculated that, for a pressure gadient of 1 psi/ft in their model, the IFT must be reduced to 0.03 dynes/cm to release oil trapped under water-wet conditions. Berkeley et al.3 indicated that, at representative field flooding rates, the IFT must be reduced to 0.001 dyne/cm to improve recovery, Thus, there is a wide variation of opinion about the IFT levels needed to improve recovery under field conditions. These previous investigators all have used as their experimental method the addition of surfactants to the injected water. The use of surfactant solutions to reduce IFT creates two experimental problems: (1) the loss of surfactant through adsorption on reservoir rock can obscure the true IFT value which exists at the displacement front, and (2) at very low values of IFT emulsifica-tion of oil and water commonly occurs. It is difficult, therefore, to determine whether the increased recovery is caused by IFT reduction as such, or is instead caused by emulsification. Also the properties of the available surfactants limit the IFT range which can be studied. In the present study the purpose is to better define how interfacial tension reduction can lead to increased oil recovery. A matter of great interest is the amount of recovery improvement potentially achievable in this way. The study was made using very low pressure gradients which was well within the range achievable by water flooding in the interwell region of petroleum reservoirs. A unique experimental approach was chosen to avoid adsorption and emulsification problems, and to allow convenient control of IFT. The fluid phases used were the equilibrium vapor and liquid phases of the methane-n-pentane system. The interfacial tension level was varied by changing the equilibrium pressure of the methane-pentane system over the range from 1,200 psia to near the critical pressure (2,420 psia). All tests were performed at a controlled temperature of 100F. The IFT-vs-pressure relationship for the methane-pentane system was based on the data of Stegemeier and Hough,6 and on new data obtained in this study. With this experimental approach it has been possible to study displacement at lower values of IFT than have been previously investigated.

Jan 1, 1967

By G Kirk

Definition and delineation of in-pit ore and waste material are the most significant tasks for an open pit production geologist; adding or destroying value in the mining value chain. Anglo American’s Mogalakwena Platinum mine, an open pit operation in South Africa moving 100 Mt/a, has recognised the value of improved material definition and is in the process of changing from blasthole to reverse circulation (RC) sampling for in-pit grade control. This is aimed at obtaining more representative samples, which are required to maximise ore recovery, minimise waste dilution and to increase the accuracy and confidence of production forecasts. Early in the project, it was realised that the key risks for implementing RC grade control were related to change management processes, rather than failure of technology. Recognising the importance of this issue, Mogalakwena chose an integrated implementation approach that incorporates all stakeholders of the mining cycle in order to develop a process that delivers maximum value and is sustainable within an active mining environment. The following core goals were addressed over five phases of project implementation: extensive definition and design of integrated project implementation, comprising: project buy-in and ownership from all key stakeholders, including survey, geology, mine planning, drill and blast, load and haul, maintenance, supply chain and finance; and detailed analysis of all potential issues and possible solutions, allocated to stakeholders as part of the scoping process; optimising hole patterns and drilling procedures, focusing on delivering maximum value for minimum cost using multiple scenario analysis from borehole data and operational sequencing requirements; and evaluation of lessons learnt during project implementation in order to optimise the technical solution and operational efficiencies. Although this project is not yet finalised, Mogalakwena Platinum Mine is already providing a blueprint for the effective development, implementation and optimisation of sustainable in-pit grade control RC drilling for other open pit mines within Anglo American plc.

Aug 22, 2011

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment. The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. Thi s paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flot ation and mixing"

Jan 1, 1988

By J. E. Nesset

"This paper discusses the importance of considering residence time distribution (RTD) in the design of flotation and mixing circuits and in the analysis of operating problems. The experiences and successes of Brunswick Mining in this area are covered and include: the development of a practical RTD measurement technique using pulp conductivity, baffle installation to improve the RTD of existing process equipment, and the method in which RTD considerations have been used to design the newest flotation and conditioning operations. IntroductionThe use of residence time distributions (RTDs) in the design and analysis of unit operations is well understood by the chemical engineering profession in while mineral processing engineers have tended to rely on empirical and rule-of-thumb factors. For example, in scale up from laboratory and pilot test results to full size flotation plant design, empirical rule s are often used to establish residence time and number of cells in the bank. Coleman suggests a factor of at least 2, and up to 5 for gold ores, be applied to laboratory determined flotation times. This is further illustrated in Table I, taken from Denver equipment.The number of cells in series to achieve the required retention time while minimizing short-circuiting has generated a variety of conclusions (Table 2). Obviously there is less than complete agreement on the subject. Young notes that a clear difference of opinion has emerged and cites as extremes, (i) the publications of Outokumpum showing unimpaired recovery for its largest machines (38 m3) compared to equivalent retention times for numerous smaller machines, and (ii) the experiences of Eastern European countries where the practice is to install banks of 30 unit s or more, operating in series, often with unit retention times of only a fraction of a minute.The empirical factors used by engineers presumably account for other than tested feed conditions, inefficiencies in large continuous machines, inevitable day-to-day circuit disruptions, gradual equipment deterioration and any other safety factor the engineer feels compelled to incorporate. An understanding of RTD concepts and techniques should help the practicing mineral engineer to develop more soundly based factors. This paper relates the experiences of Brunswick Mining in using RTD techniques in the unit operations of flotation and mixing."

Jan 1, 1988