Search Documents

By Harmon D. Nine

DISCONTINUITIES in the strain vs cycles to failure (S-N) fatigue curves have been reported for polycrystalline materials by Porter and Levy for copper,&apos; by Benham and Ford for mild steel,&apos; and by Williams and Stevens for 18/5 stainless steel.3 However, the considerable scatter of the points for polycrystalline materials have made a statistical analysis of the data necessary to confirm the discontinuities. By using oriented single crystals of high-purity material and low grown-in dislocation content, the reproducibility has been improved to a degree which makes statistical analysis unnecessary and clearly shows discontinuities in the S-N curves. A recent publication4 reports an abrupt change of slope in the S-N curve for ( 100) axially oriented copper single crystals fatigued in torsion. The reported discontinuities in the S-N curve, along with a different mode of failure in the two branches of the curve, have been interpreted as being due to two different amplitude-dependent mechanisms. Further work on copper single crystals of (111) axial orientation has now been completed which supports the existence of an amplitude-dependent change in the mechanism of fatigue. In the present study torsional-fatigue experiments were performed at room temperature in air on (111) axially oriented single crystals. The crystals were grown and prepared as reported in Ref. 4. Two different methods of growing the crystals also discussed in Ref. 4 produced crystals of two different perfections: Type I with dislocation density of >l06 per sq cm and Type I1 with dislocation density of <l05 per sq cm. In accordance with the accepted hypothesis that crystal flaws are primarily responsible for the scatter of fatigue lifetimes, particularly at low amplitudes, the values for the three lowest amplitudes for Type I crystal are believed to be uncertain. They are marked in braces in Fig. 1. On the other hand, at amplitudes above a surface shear strain (SSS) of *0.003, the data for both types of crystals are in agreement. Most remarkably the S-N curve for torsional fatigue of (111)-oriented single crystals is composed of three segments separated by rather large discontinuities, Fig. 1. Metallographic and X-ray measurements indicate that the lower branch corresponds to the low-amplitude (F) region of the (100) copper single-crystal results as discussed in Ref. 4, and the two upper branches correspond to the high-amplitude (H) region. The lower discontinuity in the (111) S-N curve and metallographic evidence give further support to the hypothesis that different mechanisms of failure operate for high and low strain amplitudes. Reference to the resolved shear stress diagram, Fig. 2, shows that the highest stressed systems in

Jan 1, 1965

[NORTH AMERICA UNITED STATES ALABAMA AUBURN Sturm & O&apos;Brien, Consult. Engrs. °Sturm, Rolland G. BESSEMER Granger, W. C. BIRMINGHAM Air Reduction Sales Crockett, John M. Amer. Cast Iron Pipe Co. Carter, Sam F., Jr. Donoho, C. K. Anderson Elec. Corp. Davis, Moss V. J. B. Clow & Sons Neptune, Maurice D. Connors Steel Div. °Sandelin, Robert W. Hayes Aircraft Corp. Ricketts, W. E., Jr. Willhelm, A. Clyde, Jr. McWaine Cast Iron King, O. H. Worthington, B. W. Shook & Fletcher Sup. Co. Gearhart, Thomas A. Southern Res. Inst. Dismukes, Edward B., Wheelahan, Edmund J. Thomas Foys Miller, Ralph M. Union Carbide Metals, Co. Brandler, Edgar A. U. S. Pipe & Fdry. Co. Clay, Donald H. Unaffiliated Berg, H. A. Caldwell, H. A. Gilmer, H. U. Harris, Thomas H. Templeton, J. B.]

Jan 1, 1961

By Joachim J. Hauser

Experiments on latent hardening were peyformed by compressing single crystals along a direction perpendicular to the tension axis. The slope and length of easy glide in the tension test were found to depend only on prior deformation in the same slip plane. Prior deformation on a different slip plane changes the stress level of the resulting stress-strain curve. The yield points appearing upon reloading after prior extension and unloading were related to the end of easy glide. SEVERAL researchers have studied the latent hardening due to deformation of a crystal by slip on a slip System after prior deformation. These experiments can be divided into those in which the prior deformation was on the same plane as the subsequent and those in which the two deformation processes were in different planes. In the former category are the experiments of Buckley and Entwistle,1 Parker and washburn,2 and Haasen and Kelly.3 The latter case has not been studied systematically; it was the main purpose of this investigation to produce this type of latent hardening and explain the results in terms of the existing theories of work hardening. In general, tension producing slip on a certain slip system can be preceded by tension, transverse compression or longitudinal compression, each with predictable dislocation movement and intersection. The intersection of dislocations can lead to glissile or sessile jogs, Cottrell-Lomer locks and other sessile dislocations. The effect on the stress-strain curve could depend on which combination of the former mechanisms is operating. Haasen and Kelly3 have studied the yield points which occur in aluminum and nickel single crystals upon reloading after prior unloading in a tension experiment. They attributed this effect to the anchoring of dislocations occurring during unloading. As Cottrell and stokes4 have shown that dislocations cutting through the "forest" could only lead to reversible changes, they attributed the anchoring to the formation of sessile dislocations during unloading. However, different kinds of sessile dislocations could be formed during unloading, and it was the purpose of this experiment to determine whether Cottrell-Lomer locks are responsible for the yield effect and for the end of easy glide. The case where a longitudinal compression is followed by tension along the same axis is commonly referred to as a Bauschinger test. This type of effect was studied by Buckley and Entwistle1 on aluminum single crystals and by Parker and washburn2 on zinc single crystals. In such a test, the tension and the compression activate the same slip plane with opposite slip directions. The use of sideways compression in the present experiments permits the activation of different types of slip systems and the study of their effect on the easy glide region and on the transition between the elastic and easy glide region. The theory of seeger5 for the flow stress in fee materials is applied to explain the latent hardening. EXPERTMENTAL PROCEDURE All the single crystals used in this investigation had an axial orientation close to <210>, called the "0.5" orientation. This is the orientation for which the tensile axis is 45 deg from both the slip plane and the slip direction. The single crystals were grown from the melt under a helium atmosphere using milled graphite boats,=at a rate of 8.6 mm per min. The silver used in the experiment was 99.98 pct pure. The single crystals had a square cross section about 0.9 by 0.9 cm and a length of 14 cm. The orientation of the specimen was determined within ±2 deg by the Laue back-reflection method. The specimens were annealed at 940&apos; ± 2°C in a helium atmosphere for 24 hr and then furnace cooled over a period of 7 hr. The specimens were electropolished in a solution of 9 pct KCN in water. The specimens were tested in a soft-type tensile machine (the load is prescribed) up to 3 pct strain. The stress was increased continuously at approximately 30 g per mm2 per min. The strain was measured over a 5 cm gage length with a mechanical extensometer employing an optical lever. The strain and stress were measured with accuracies of i 2 X 10-5 and ± 2 g per mm2, respectively. The remainder of the stress-strain curve up to 20 pct strain was obtained in a hard-type tensile machine (the strain rate is prescribed). The strain and the stress were measured in that machine with an accuracy of ±2 pct. The compression tests were performed in the hard-type machine using accurately machined steel blocks without lubrication. The blocks were used so as to apply a uniform compression over a length of 13 cm. The strains were measured on the hard-type machine and with a micrometer.

Jan 1, 1962

Strain-Hardening Exponent of Cross-Rolled Beryllium Sheet by S. R. Maloff, Vol. 215, No. 5, page 872, was omitted from Table of Contents for the October issue. Stabilization Phenomena in Beta Phase Au-Cd Alloys by Howard Birnbaum, Vol. 215, No. 5, page 786. The figure denoted Fig. 1 should be Fig. 3, Fig. 3 should be Fig. 4 and Fig. 4 should be Fig. 1. The captions are in the proper sequence. Activity of Carbon in Liquid Iron Alloys by Tasuku Fuwa and John Chipman, Vol. 215, No. 4, page 708. First equation, right hand column, page 710 should read

Jan 1, 1960

By Michael D. Justason

"In January 2009, long-time competitors, Anchor Shoring & Caissons Ltd. of Toronto and Bermingham Foundation Solutions of Hamilton, joined forces to tackle one of the Greater Toronto area’s largest deep foundation projects: the West Toronto Diamond Rail Grade Separation. The two companies formed the “West Diamond JV” and succeeded in winning the contract from the Canadian National Railways. This deep foundations work was the first and most significant part of the $300-million-plus rail grade separation project. A big part of the job turned out to be dealing with local government regulations and citizens’ concerns with noise and vibration.The project is approximately 10 km (6 mi) northwest of downtown Toronto in an area of mixed-zoning including light industrial, commercial and residential buildings. The area is commonly called the “The Junction,” because of the heavy rail- traffic. The “West Toronto Diamond” refers more specifically to the railway junction where the North-South tracks of Canadian National (CN) Railway meet at a level crossing with the East-West tracks of the Canadian Pacific (CP) Railway. The goal for this part of the project was to convert the West Toronto Diamond into a grade-separated junction by depressing the CN lines under the CP lines, thus allowing commuter rail carrier, called GO Transit, intercity carrier VIA Rail, and CN freight trains to pass through the new underpass.Dawn Tattle, president of Anchor Shoring & Caissons says, “not only is the site in a densely populated area adjacent to homes and businesses, the crews worked adjacent to active rail lines with numerous trains passing daily. During the 7-hour working day, approximately 60 trains passed through the site in very close proximity to working crews.” Safety was paramount. While trains were passing through the site, it was a railroad requirement that all equipment and men stop working. In addition, at those times, all personnel were required to stay 6 m (20 ft) from the tracks and were required to face the tracks. For the faster commuter trains, this work interruption could last as little as 2-3 minutes, while interruptions caused by the slower freight trains could last as long as 25 minutes. The most disruption to the site occurred during the morning commute between 7 to 9 a.m., so work did not really get underway until after that time. Once work finally commenced the race was on to finish as much as possible before the afternoon commute – hence the shortened work day. The amount of disruption caused by the trains was a big unknown faced by the JV going into the project, but crews adapted quickly to the very unusual work environment"

Jan 1, 2012

By H. Kinilakodi, R. L. Grayson

In 2010, the U.S. Mine Safety and Health Administration (MSHA) began holding hearings on a new coal mine respirable dust rule, which proposed a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the “hot spots” where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines’ compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, average mining height and selected “hot spot” counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications for the need for better dust control methods.

Jan 1, 2012

By Zhen Hu, Chenghang Wang, Jianjian Zou, Xiujuan Li, Hanwen Li, Tai Wang, Baoxu Song

A rare earth deposit in Sichuan, China is rich in wulfenite in addition to bastnaesite and barite, and the deposit has already adopted high intensity magnetic separation technique to pre-enrich the rare earth minerals, during which the wulfenite and barite have been left in the non-magnetic product. Because the chemical composition of wulfenite is only 24.17% Mo and 42.15% Pb, it is very hard to obtain qualified lead or molybdenum concentrates by physical separation process. To pre-concentrate the wulfenite, flotation has been first introduced, and by using 100g/t GY-7 as dispersant, 1500g/t CP-1 as depressant and 160g/t GY-4 as collector, a floatation concentrate assaying 15.52% Mo with a recovery of 86.12% was obtained. Then a leaching process was conducted by using 1.2mol/L Na2S as leaching agent, and molybdenum can be translated into sodium molybdate in the solution with a leaching recovery of 99%. To recover rare earth oxides (REO) and lead from the leaching residue, a magnetic separation process has been conducted. Above all, by the whole process, the molybdenum recovery reaches 86.16% in the sodium molybdate solution, and a lead concentrate assaying 54.59% Pb with recovery of 27.99% could be obtained.

Jan 1, 2014

By L. Adler

Analysis of a mine roof can be based on fixed-end beam behavior. The author here analyzes the effects of zero restraint at deflecting beam supports. Formulae are given for determining permissible support deflections. Analysis of a mine roof in a bedded deposit usually follows the assumption that the behavior of the roof is analogous to a beam with both ends fixed. Yet it is recognized that the end restraint itself varies with the thickness of cover, so that at shallow depth the restraint is minimum, and at great depth, maximum.&apos; Consequently, an analysis on the basis of fixed ends or full restraint represents only one extreme in the possible range of conditions. Since the actual amount of restraint is difficult to ascertain, a more rational approach is to consider the two extreme cases of end restraint. Such situations regarding uncertainty of the restraining effects of supports are not uncommon in structural analysis, and are handled in a like manner.&apos; Since previous studies9)4 have dealt with full restraint, this paper will analyze the effects of zero restraint at deflecting beam supports. In such a case a mine roof with several intermediate supports becomes analogous to a uniformly loaded continuous beam on simple supports, as shown in Fig. 1A. Such a structure is statically indeterminate to a degree equal to the number of intermediate supports, n. Therefore, with the three equilibrium equations, n additional equations are needed. A number of methods exist to analyze this problem, but The Theorem of Three Moments is Simplest. The continuous beam is divided at each support into a sequence of simply supported single span beams, with the unknown end moments, as appears in Fig. 1B. Continuity requires that the common ends of adjacent beams have the same slope (Fig. 1C). eiB= B(i+l)~= ei(i+l)and MiB= Mti+I)A= Mi(i+i). [1I A Glossary of all terms is given in Table I. Furthermore, if we first consider that the supports do not deflect, the slope at a support is the sum of the slopes due to each of the individual loads shown in Fig. 2, yielding:

Jan 1, 1961

By N J. Beukes, S T. Netshio, M O. de Kock

The Thabazimbi iron ore deposit comprises a series of stratabound orebodies, on average 18 - 25 m thick that are aligned along the faulted basal contact between the Penge Iron Formation and dolostones of the Malmani Subgroup, Transvaal Supergroup. Field geological relationships and petrographic observations suggest that the formation of high-grade iron ores took place after contact metamorphism related to the intrusion of the Bushveld Complex (2.06 Ga) but before the deposition of red beds of the Waterberg Group at ca 1.9 Ga. Hard, high-grade iron ores are predominantly composed of martite and microplaty hematite. Goethite is restricted to supergene-modified ores close to the Late Cretaceous û Early Cenozoic Old African land surface. At depth, the high-grade hematite ores interfinger with low-grade dolomite-hematite and calcite-hematite ores. Iron oxides (martite, microplaty hematite) present in these low-grade ores are texturally indistinguishable from those in the associated high-grade ores, ie ore formation is genetically associated with carbonate metasomatism. Microthermometric studies of fluid inclusions in sparitic carbonates and rare megaquartz reveal their hydrothermal origin. Two compositionally distinct aqueous fluids of shallow crustal origin are identified, namely a Ca-Na-rich high-salinity brine (26 wt per cent NaClequivalent, TH ~160¦C), and an aqueous Mg-K-bearing fluid of intermediate salinity (8.3 - 12.6 wt per cent NaClequivalent, TH~120 - 150¦C). The results confirm that high-grade hematite orebodies at the Thabazimbi deposit owe their origin to an event of extensive oxidative carbonate metasomatism (calcification), similar to that recognised at other important high-grade iron ore deposits in the world. Hydrothermal ore formation is both structurally and lithologically controlled. Size and quality of the orebodies was improved by Late Mesozoic-Cenozoic deep lateritic weathering as carbonate-hematite ores were enriched to friable high-grade ores, but this supergene modification is second in importance compared to the primary event of hydrothermal ore formation.

Jan 1, 2005

By Stanley J. LeFond

The Republic of Botswana, one of the newer countries of southern Africa, attained independence on September 30, 1966. It covers an area of about 225,000 square miles (582,000 square kilometers) which makes it slightly larger than France, or slightly smaller than Texas. It is bounded by Zimbabwe, the Republic of South Africa and Namibia, including the Caprivi Strip. Angola and Zambia are close neighbors. (Map 1). Botswana lies at the center of the southern African plateau at a mean elevation of 3,300 feet (1,000 m). It is a natural habitat for most species of African fauna. The rolling sands and extensive grasslands of the Kalahari Desert cover the southwest. The climate is sub- tropical. Summers, although tempered by north- easterly breezes, are hot, but mean maximum temperature seldom rises above 100°F (38°C). Winters are dry with wide temperature variations, which often give rise to frosts.

Jan 1, 1981

Mining Equipment Challenges Equipment Availability Unplanned downtime Maintenance Costs Secondary damage and catastrophic failures (T282 $750k) Emergency work is 4x the cost of planned work Inspections Troubleshooting time Incorrect repairs (parts, labor, lost production) Equipment Life Mis-operation of equipment

May 1, 2013

By D. A. Dukelow, G. Derge

THE Fe0-Mn0-Si0, system has many properties of fundamental interest besides its occurrence in steel-making. The system is the simplest ternary complication of the FeO-SiO, binary whose electrochemical properties have been explored. Therefore, knowledge of the conformance of Fe0-MnO-SiO, melts to Faraday&apos;s laws, as investigated by current efficiency measurements, would be of particular value in interpreting the observed variations of electrical conductivity, while at the same time furthering understanding of this type of molten oxides. Pertinent to the present study are conductivity data of FeO-SiO, and Fe0-Mn0-SiO2, and current efficiency data of FeO-SiO,. Concerning conductivity measurements, Inouye, Tomlinson, and chipman&apos; studied the specific conductivity, a, of molten wüstite as a function of temperature and oxide addition. Liquid FeO in equilibrium with an iron crucible was found to have a o whose magnitude and positive temperature coefficient were undeniably semiconductor in nature (o1400°C = 269 ohm-1cm-&apos;). Additions at 1400°C of 5 mole pct MnO decreased o to 227 while a similar addition of SiO2, dropped o to 125. Additional SiO2 produced an exponential decline of o. It was reasoned that because wüstite is known to be oxygen excess and since there is no pronounced change in oFeO upon melting, that UFeO(L)is p-type semiconduction. Björling2 gives o data for the ternary FeO-MnO-SiO, using fayalite, 2 FeO-SiO,, as the base substance. Upon addition of tephroite, 2 MnO-SiO, he noted a small decrease in o. Taking his data for 1400°C with one-half of the fayalite replaced by tephroite, o shows a decrease of some 40 pct relative to o for fayalite, i.e., 5 ohm-&apos; cm-&apos; to 3. In line with this observation, Mori and Matsushita3 reported that substituting MnO for FeO in the silicate de- creased o slightly except at high SiO, contents where the decrease was somewhat larger. Investigating the ionic nature of FeO-SiO2 melts, Simnad, Derge, and George4, found the anode current efficiency, C,, as calculated from iron anode weight loss, was temperature invariant and in general increased with SiO2 concentration. The authors suggested the possible presence of electronic conduction to explain why C+ < 100 pct. Fig. 4 includes their results as curve (b). EXPERIMENTAL METHOD Apparatus—Fig. 1 is a schematic section of the electrolysis cell used in all the current efficiency runs. The melt was contained in an iron crucible that rested on an alundum ring. A centered silica tube came within 1 in. of the surface of the melt and initially served as a thermocouple well and then as the guide for the anode.

Jan 1, 1961

By Douglas A. Karvonen

"Competition in the world potash market has increased significantly since the late 1970s. The failure of consumption to grow at expected levels has led to industry over-capacity, a situation which is likely to persist at least until 1990. Individual Saskatchewan producers and their offshore marketing company, Canpotex, have responded to this challenge by increasing mining efficiency, developing more cost-effective and reliable transportation systems and establishing innovative financing and market development programs tailored to customers&apos; special needs. Investment in warehouse facilities to serve U.S. customers and exploration of opportunities for intermodal distribution through the Great Lakes and the Mississippi River system have maintained individual producers&apos; position in the highly competitive domestic market.Export sales through Canpotex have been bolstered by utilization of CIDA funds, Exp ort Development Corporation financing guarantees and other innovative payment plans which enable heavily indebted developing countries to maintain the import levels which are necessary for their agricultural development.IntroductionPotash is the general term applied to various potassium salts both natural occurring and commercially derived. The most common of the commercial product s are potassium chloride, potassium sulphate and potassium magnesium sulphate. The potassium content of potash is measured in units of K20 equivalent. The common grades of potassium chloride produced for agriculture average at least 60 0/0 K20 compared with approximately 50% Kp for potassium sulphate and 22% for potassium magnesium sulphate."

Jan 1, 1985

IT is a pleasure for the translators to record their gratitude to the Seeley W. Mudd Memorial Fund of the American Institute of Mining and Metallurgical Engineers for underwriting the cost of publication of this volume, to the Printing-Office of the Yale University Press for doing an unusually fine printing job, and to the following for granting permission to reproduce the title pages of volumes in their collection: The Bibliothèque Nationale of Paris, for edition A of the Bergbüchlein; the Osler Library of McGill University, Montreal, for editions B and G of the Bergbüchlein and edition D of the Probierbüchlein; Mr. Herbert Hoover, Jr., for editions C and E of the Bergbüchlein and editions E, M, N, and 0 of the Probierbüchlein; the Parsons Collection of the Reference Department of The New York Public Library, for edition D of the Bergbüchlein; the Library of the Bergakademie Freiberg, for edition F of the Bergbüchlein and editions A, H, and L of the Probierbüchlein; the Herzog August-Bibliothek of Wolfenbüttel, for edition C of the Probierbüchlein; the British Museum. Library, London, for edition I of the Probierbüchlein; and the library of the University of California at Berkeley, for edition J of the Probierbüchlein. The cooperation of those who helped with the translation of the Bergbüchlein is acknowledged on p. 64. A. G. S. C. S. S.

Jan 1, 1949

By T. T. Read

TWO papers on health and safety were given Thursday afternoon when a joint session of the Health and Safety Committee and the Mining Methods Committee was held. T. T. Read presided and the first paper, on ventilation at Climax, was presented by the author, L. H. Glanville. In the subsequent discussion by Cloyd M. Smith, P. B. Bucky, B. F. Tillson, D. F. Haley, J. L. G. Weysser, and others a number of interesting points not covered by the paper, which appears in full in the January Mining Technology, were brought out. Ventilation troubles in mines so often hinge on the air being too hot and damp that it was interesting to hear of one where it is frequently too cold and too dry.

Jan 1, 1943

By CASSANDRA L. HOEBBEL, Jennica L. Bellanca

High-fidelity, immersive training is known for its learning and logistical benefits. While other industries have used virtual reality (VR) for decades, the same uptake has not been seen in mining. NIOSH recently developed an adaptable, scalable VR training platform, VR Mine Rescue Training (VR-MRT), which has attracted significant industry interest. NIOSH is using VR-MRT to understand the barriers to adoption and implementation of VR. As a part of a larger effort to assess the effectiveness and implementation of VR-MRT, researchers have conducted pre-implementation interviews. In this paper, the authors use feedback from individuals at various implementation levels to assess the acceptability and appropriateness of VR-MRT and identify potential implementation barriers for VR more generally. Researchers also describe ongoing efforts to overcome these barriers as NIOSH works to position VR-MRT as a supplemental resource more generally for mine safety training.

Feb 1, 2025

By P. F. MINISTER

AT Lime Spur, Mont., the East Butte Copper Mining Co. has been quarrying limestone for twenty years. The quarry is beside the Northern Pacific R. R. in the Jefferson River canyon, 4 ½ miles east of Cardwell, at Lime Spur, Montana. HISTORY This quarry was opened early in 1900 by Dan Morrison of Whitehall, the discoverer of the Morrison cave, to supply a demand for smelter flux. Limestone was sold to the Pittsmont smelter of The East Butte Copper Mining Co. and to the Butte Reduction Works. As no particular effort was made at the quarry to select the rock that delivered to the smelters was unduly high in magnesia and impurities. The East Butte com¬pany, therefore. Bought the quarry. in 1909 and confined operations to the high-grade beds in order to supply rock of the desired purity for its own smelter and the Butte Reduction Works until the latter shut down. It also developed a market for some of its rock with the sugar factories. The latter market increased until in later years all rock, larger than 4 in. in size over a bar grizzly, was being shipped to the sugar factories, and the rock smaller than 4 in. was being used as a flux in the blast furnaces at the Pittsmont smelter. In 1924, the East Butte concluded a contract with the Anaconda company for the treatment of its ores, and the Pittsmont -smelter -was shut down: which made the minus 4-in. rock a useless by-product. Since there was not enough revenue in the sugar rock alone and also because of limited waste room it became necessary, if Lime Spur was to continue to operate, to increase- the proportion of plus 4-in. rock and to develop a market for the minus 4-in.

Jan 1, 1930

By J. J. Beeson

For the past fifty years or more, the structural features of the Cordil-leran mountain system of western United States have presented some most interesting problems. Any geologist or engineer living in this region, or even making occasional examinations of the mines, will lose much of interest and importance if he is not familiar with the literature. Some of the greatest works on geology have been the result of studies carried on in sections of this region. Among the more important of the earlier works are those of Dutton,l King,2 Gilbert3 and Powell;4 of the more recent Lindgren,5 Ransome,6 Spurr,7 Butler8 and others have contributed much. Many of the papers are largely of scientific interest but even these lay the foundation for the commercial application of the broader features of the geology. I have read many of these works with the keenest interest and pleasure; in fact, some have been read until some of the more important findings seem to be my own. In this paper, however, it is my aim to accept credit for little more than the labor of assembling some of the ideas of others. This is done with the hope that an interesting and valuable discussion will be the result. If some of the ideas presented should

Jan 1, 1927

By S. K. Sarkar, B. Dr. Singh

INTRODUCTION India like USA has traditionally relied on bord and pillars as dominant underground method. Coal has generally been mined at shallow depth from relatively thick and horizontally bedded coal seams. These&apos; factors contributed towards large scale adoption of bard and pillar. After nationalisation of coal industry in two stages in 1971 and 1973, large scale mechanisation and modernisation programmes were undertaken. Longwall mining was identified as one of the major that area for increasing underground coal production. The idea to introduce longwall mining was mooted to increase productivity and to promote conservation and safety. The nationalised coal industry has already worked about twenty longwall faces with different types of support. The tempo of introducing longwall is catching up and a number of longwall programmes with, Self advancing supports of different types and Capacity are in active stage of implementation. The country has not yet started producing mechanised Supports and therefore supports and machineries are being imported from U.K. and other countries of the continent. The of the major problem faced in the longwall projects is to choose suitable type and capacity of supports. The suppliers and manufacturers of these supports are not competent enough to choose and offer the right type and capacity of supports as their knowledge and information about Indian strata conditions are extremely limited. The Central Wining Research Station (Q.!RS), has undertaken a research programme for evaluating the rock mechanical conditions obtaining in the proposed longwall locales and has worked out a method for selection of proper type and capacity of supports on the basis of projected strata behaviour at the proposed locale. STRATA CCNTROL FAILURES Indian coal industry had made some attempts to introduce longwall caving in the early fifties after a working group set up by the Government of India had recommended its adoption to increase productivity and to modernise mines. Approximately 20 longwall faces were tried in the major Indian coalfields of Jharia, Ranigunj and Karanpurr between 1951 and 1968. The supports used consisted of 20T hydraulic props or 35140~ friction props. A number of these faces had suffered total strata control failures and a large number of support elements were lost. The Central Mining Research Station initiated a research programme to analyse these failures in the general background of behaviour of Indian coal measure strata at longwall faces. All the available data regarding the cases of failures were collected and physico-mechanical properties of overlying roof rocks were determined in the laboratory. Simultaneously, observations were continued to establish the behviour pattern of Indian coal measure strata at longwall faces. These studies were helpful in analysing the occurrences of collapse. BEHAVIOUR OF INDIAN COAL MEASURE STRATA The coal measure strata encountered in the principal Indian coalfields of Jharia, Ranigunj and Karanpura are in general strong in nature however, the immediate roof (mostly up to 1.5 to 2 m) in most of the cases is weak and false bedded shale. MI idea about the strength properties of immediate and overlying roofs may be obtained from the following table.

Jan 1, 1982

By H. E. Peterson

A study was undertaken by the Bureau of Mines to develop a simple, reliable test for field detection of selenium in rocks and soils. Two methods are described for qualitative detection of selenium, dependent upon its form of occurrence and the presence of interfering constituents in the sample. Both methods involve fusion of the sample in a test tube to form elemental selenium that will volatilize and condense as a red deposit on the cooler upper portion of the test tube. The methods are sensitive to 10 parts per million, (p.p.m.) equivalent to 0.001 percent, and can be made semiquantitative by using suitable standard samples. INTRODUCTION Although selenium is widely distributed in the United States, the known deposits are either so small or so low grade that they cannot be processed economically for selenium alone-4/ At present, commercial production is a byproduct of the smelting and refining of base-metal ores, particularly copper.5/ About 0.75 pound of selenium is recovered per ton of electrolytic copper, and small amounts are recovered by special treatment of assorted smelter dusts and fume products. Since selenium is a strategic metal in short supply, new sources are being sought by both Government and private interests.

Jan 1, 1957