Search Documents

Executive HOWARD N. EAVENSON, Chairman FREDERICK M. BECKET EDGAR RICKARD ERLE V. DAVELER WILLIAM WRAITH Finance HENRY KRUMB, Chairman PAUL I). MERICA J. V. W. REYNDERS H. G. MOULTON, Consultant Admissions JOHN M. LOVEJOY, Chairman GEORGE D. BARRON DONALD M. LIDDELL ELI T. CONNER WILLIAM W. LYNCH Alternates WM. H. BASSETT, JR. L. B. LINDEMUTH W. A. SINSHEIMER

Jan 1, 1934

By A. G. McGregor

In the Southwest a number of large steel chimneys discharge the gases from the copper smelting furnaces. Some of these chimneys show no deterioration after twenty years, others show serious deterioration after tour years service. A steel stack 20 ft. 7 1/2 in. (6.3 m.) in diameter by 279 ft. (85 m.) high, Fig. 1, used for roaster gases only at the Calumet & Arizona Mining CO.'s plant at Douglas, Ariz., was lined to the top of the bell, 40 ft. (12 m.) from the base, with common brick placed on end, lime and cement mortar being used. Above the bell, the stack was lined with 4 by 4 by 8 in. (10 by 10 by 20 cm.) building tile, placed on end, making a lining 4 in. thick. The tiles were supported on angle-iron rings, riveted to the inside of the chimney shell about 15 ft. apart. The chimney was put into use in the latter part of 1913. Four years later, considerable of the tile lining had fallen out of place and mixed with the flue dust at the bottom of the chimney. About a year later, several flattened and distorted sheets were noticed about 70 ft. below the top. An investigation showed that the thickness of these distorted sheets, which was originally 1/4in., had been reduced one half. One year later, or six years after the chimney went into use, several holes, a square foot and smaller in area, appeared near the flat spots mentioned. Soon afterwards, when the chimney was shut down for repairs, it was found that most of the tile lining for 125 ft, from the top had fallen out and that the steel shell was badly corroded; but where the lining remained in place the shell was undamaged. Many of the tile which had fallen out of place had become soft or flaky and crumbling, others were as hard as when placed. An analysis of the hard and soft tile is shown on p. 2. These tile were of a fireclay mixture, and were used instead of common brick on account of lower cost. The steel forming the upper 125 ft. (38 m.) was replaced, and a 4 1/4-in. (11-cm.) lining of firebrick was laid from the bell to the top of the chimney. The brick were placed on end, wedges and keys being used. After each 8-in. course was set, keyed, and wedged tight, thin mortar —water, sodium silicate, and finely ground silica—was worked into the joints. The brick are supported on angle-iron rings, every 15 ft., in the same way as the tile.

Jan 1, 1921

By J. W. Matousek

Copper losses in smelter slags are :typically normalized with some form of the distribution coefficient, written as the ratio of the weight percent assays of metal in slag to the metal in matte or its inverse: L(s/m) = %(Cu)/%[Cu] or L(m/s) = %[Cu]/%(Cu) However, this simple approach ignores the dynamics of the smelting process. It overlooks the effect of the chemical work done in producing a given matte grade from concentrates of different grades -- or from a single concentrate blended with varying quantities of copper bearing precipitates or reverts. This paper examines the combined influences of matte grade and the work done in smelting on the copper content of smelting furnace slags. A simple model for the relationship is proposed.

Jan 1, 1999

By Paul M. Tyler

One of the best present-day yardsticks of the material welfare of a nation is its consumption of minerals, The United States, with only 7 percent of the world population, consumes 45 percent of the world wealth, pays the highest real wages, has the shortest working hours, and numbers the largest percentages of home owners among its population, and at the same time its per-capita consumption of minerals is far greater than that of any other nation. In 1937, British India, with roughly twice the population of the United States, used less than 2 percent as much lead, 4 percent as muck zinc, and 13 percent as much copper; even in Europe, which has three times our population and where war preparations have greatly expanded the normal needs of peaceful industries, the aggregate consumption of metals and industrial minerals other than lignite is less than the total for the United States alone. The march of civilization passed from the Stone Age to the Bronze Age before the dawn of history. It may be questioned whether man or monkey first threw stones at an enemy, but only man could have fashioned rough stones into weapons. Eoliths rudely shaped by apelike men are believed by archaeologists to have antedated by hundreds of thousands of years the existence of our own human ancestors. The primitive people that followed the retreating Ice Cap northward in early quaternary period - at least a million years ago - were fairly adept in the shaping of flints and even used a little copper. The Bronze Age, so-called, superseded the Stone Age when, around 8,000 B. C., the news spread that chunk s of natural copper could be pounded into better weapons or cutting implements than ever could be made by chipping stones. The Bronze Age gave place to the Iron Age about 1,000 B, C., and though students of modern history may speak of the Coal Age, the Petroleum Age, and the Automobile Age, and so on, these ages have all been crowded into a brief century and a half. The truth is that we still are in the Iron Age, unless perhaps we choose to call it the Age of Many Metals.

Jan 1, 1940

By Mala Nath, Atjit Mallick, Asheesh Kumar

"The present research work is aimed to focus on the development of chemically stable light weight microporous carbonaceous material, such as activated charcoal incorporated either with titanium n-butoxide, titanium diisopropoxide bis(2,4-pentanedionate), vanadium 2,4-pentane-dionate or zinc 2,4-pentanedionate having varying wt% of the metal (2-8%) using ethanol as solvent at 40--50 oC followed by calcinations at 100, 150 and 200 cC, except the samples with titanium diisopropoxide bis(2,4-pentanedionate) which are calcinated at 80 oC. Atomic absorption studies along with FESEM revealed that the maximum incorporation of metals (Zn, V and Ti) in activated charcoal was observed with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC , 4 wt% of vanadium 2,4-pentanedionate at 100 oC, 2 wt% of titanium n-butoxide at 100 oC and 2 wt% of titanium diisopropoxide bis(2,4-pentanedionate) at 80 oC, and equilibration time of 20-24 h was used in each case. Hydrogen sorption behavior in these carbonaceous materials has also been studied at 77.4 K and low pressure up to I bar. The highest hydrogen uptake obtained was 1.45 wt% (164.5 cm3 (STP)/g at P/Po = 1.0) for activated charcoal incorporated with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC.IntroductionTwo of the major challenges for humanity in the next twenty years are the shrinking availability of fossil fuels, the global warming and potential climate changes that result from their ever-increasing use. So it is necessary to fmd an energy source that is convenient, flexible and controllable. One possible solution to these problems is to use an energy carrier such as hydrogen, and ways to produce and store hydrogen in electric power plants and vehicles. Hydrogen storage is the bottleneck for the breakthrough of hydrogen as energy carrier in automotive applications [1]."

Jan 1, 2012

By D. E. Van Dillen

Seven configurations for panel entries of a longwall coal mine are compared and ranked according to structural stability. These entry configurations are analyzed using three-dimensional finite element modeling The models include large dimensions to minimize boundary effects, elastoplastic constitutive relations, and simulated excavation and construction of support systems. The stability criteria are formulated in a quantitative manner to facilitate the ranking of the entry configurations. These criteria are based on the expected volume of caved rock in the entry openings. The stability ranking is applied to the entry excavation phase, the headgate phase, and the tailate phase of the entry life cycle. Parametric variations are applied using two-dimensional finite element models to determine the sensitivity to changes in mining and design parameters.

Jan 1, 1981

By Walter Stern

THE self-potential or spontaneous polarization method is one of the oldest in the field of electrical exploration. When applied in prospecting for ore bodies, it is one of the most rapid and inexpensive means of locating indications of ore bodies at shallow depth. Usually, the procedure is to survey the equipotential lines of the electrical field that is generated by the electrochemical activity of the ore near the ground-water level, and to localize the so-called negative centers or points of greatest negative anomaly. Another field procedure involves the measurement of potential differences along potential profiles, generally laid out at right angles to the assumed strike. Again, in such survey, the basis for establishing the presence of ore is the location of negative potential anomalies. The earlier writers on the subject, notably Schlumberger1 and R. G. Wells,2 did much to clarify the fundamental electrochemical phenomena involved. Interpretation of the field data, however, remained largely qualitative. In 1925, A. Petrovsky3 analyzed the relation between the shape of the potential anomaly curve and size and depth of an ore body by assuming the subsurface body to be a polarized sphere.4 Along similar lines of approach, Edge and Laby5 considered the ore body a dipping sheet with limited extent in the direction of strike, while Poldini6 based the theory on the assumption of a dipping bar. The following study endeavors to enlarge [ ] FIG. I.-ORE BODY CONSIDERED AS DIPOLE upon these earlier investigations and attempts, on the basis of the potential distribution of a polarized bar, to indicate certain characteristics of the anomaly curve that make possible the determination of depth, size and dip of a subsurface body. THE SPONTANEOUS POLARIZATION FIELD SET UP BY AN ORE BODY If a sulphide ore body is subjected to oxidation varying in degree in its upper and lower parts according to the difference in the concentration of oxygen within the surrounding medium, an electrical potential field is set up. The form and distribution of this field will be investigated herein with special reference to its components on the earth's surface. Under the simplifying assumption that the ore body may be considered as a dipole with the point sources QI and Q2 situated at its upper and lower ends (Fig. I), the potential of the spontaneous polarization at point P is given by the following equation:

Jan 1, 1944

By K. Saberyan

A technique is described for the solvent extraction of zirconium. In this method, zirconium has been extracted quantitatively from 0.005 M sodium salicylate solution at pH 2.5 - 3 using 0.01 M triphenylphosphine oxide dissolved in toluene as an extractant. Zirconium has also been recovered quantitatively from 0.2 M potassium thiocyanate solution, but extractions in nitric and hydrochloric acids (as media) were negligible. The resulting extracted metal ion has been stripped with sulfuric acid (0.5 M) and determined with inductively coupled plasma atomic emission spectrometry. This method has been applied successfully to achieve 95% recovery of zirconium from zircon concentrate.

Jan 1, 2010

By James A. West

The Quapaw pool is one of the smaller pools in an extensive area of Bartlesville-sand production in the eastern part of Osage County, Okla. (fig. 1). Most of the fields in this area were discovered from 1906 to 1916 and were developed and operated similarly. The Quapaw pool is representative of the area, and much of the developed in studying this pool is applicable to the other reservoirs. This petroleum-engineering study of the Quapaw pool was conducted to provide reservoir data that may aid in more widespread application of the intensive secondary-recovery production methods that have been employed with excellent results in the Bartlesville-sand fields of nearby Washington, Nowata, and Rogers Counties. This study is particularly appropriate because of the intense interest in Osage County fields as areas suitable for water flooding. Water flooding was introduced first into Oklahoma during 1931 in Rogers County, and activity was concentrated in the shallow Bartlesville-sand fields of and Nowata Counties for many years. Although water-flooding projects are now operating throughout the State, the intense activity of the Nowata-Rogers Counties area spread to adjoining counties only during the past few years. Since 1948 the rate of oil production in Washington County (between Nowata and Osage Counties) has increased by 260 percent as a result of water flooding. Currently, leases in eastern Osage County are sought eagerly by water-flood operators, and during the past 2 years the Osage Indian Agency has issued nine permits for water-flooding projects in eastern Osage County. Water-flooding operations are in progress on several projects. Although large oil reserves in eastern Osage County should, be recoverable by water flooding, development and operation of projects will be more expensive than projects in the shallower producing areas to the east. In addition, the Osage County reservoirs appear to be more complex and somewhat more difficult to water-flood successfully. It is hoped that this study will contribute to better understanding of the Quapaw reservoir and, in a general way, to the many similar reservoirs in eastern Osage County.

Jan 1, 1952

One-half fare return rate again available to members of the Institute and dependent members of their families. DON'T FORGET YOUR RAILROAD CERTIFICATE Over 300 members of the A. I. M. E. and dependent mem-bers of their families attending the last annual meeting se-cured return railroad tickets at half price by means of the railroad certificate, thereby saving several thousand dollars. DIRECTIONS 1. Be sure to obtain your railroad certificate when pur-chasing your railroad tickets for the meeting or you will lose money. 2. Purchase your tickets at regular one-way adult tariff fare between the dates specified for your territory in the accom-panying table. 3. Present your certificate for valida-tion at Institute headquarters in New York immediately after registration. Certificates will be validated on Feb. 21 and 22 between 9 a. m. and 5.30 p. in. 4. You must use your return half-rate tickets not later than Feb. 27. 5. Use the same route for both going and return trip. PLEASE REMEMBER THIS 1. Unless-250 certificates are validated at headquarters it will be impossible for anyone to secure the reduced rate. 2. Unless you secure a certificate you cannot take advantage. of the half-rate return fare, even if the necessary 250 certificates are validated.

Jan 2, 1928

By Adrian C. Dorenfeld

Concentradora "Dana Aida" (100 t/d capacity) was built in 1971-1972 to treat dumps and ores containing mixed oxide-sulfide copper-gold-silver minerals from two veins. The veins, Don Felipe and aria are about 150 m apart, but are distinctly different mineralogically. The deposit is near San Juan de Guadalupe, Durango. Mexico. All new process equipment was manufactured locally, in or near Torreon, Coahuila. Sampling, ore testing, flowsheet design, plant design, drawings purchasing, financing, etc. was planned and directed by two engineers. Construction was executed by local miners and common labor (largely agricultural). The paper presents detailed costs for equipment and construction. The subsequent breaking-in operation is discussed.

Jan 1, 1979

By S. W. Brooksbank, R. A. Benkis

"IntroductionThe Republic of Indonesia is a developing Southeast Asian country that unites the Indian and Pacific oceans, and spreads across nearly 14000 islands with a total land area of about two million km-. The distance across the country approximates the distance across Canada: Indonesia extends for more than 6000 km from the northern tip of Sumatra to the eastern border of Irian Jaya in the middle of New Guinea. With a population of around 180million, Indonesia is one of the world's most populous countries. A mix of 366 ethnic groups populates the country and there are some 250 distinct languages spoken. The topography of Indonesia generally is quite rugged because of its numerous volcanos. For example, the island of Java has 121 volcanos, of which 15 rise above 3000 m and another 44 reach heights between 2000 m and 3000 m.Indonesia has a diversified resource base, with plentiful energy resources (coal, oil, gas and hydroelectric), significant mineral deposits, large timber potential and a developed system of agricultural commodity production and export. A high proportion of the primary resources are on the sparsely populated islands of Sumatra and Kalimantan, whereas 7'3 of Indonesia's people reside on Java, or on 70/0 of the country's land area. Around Jakarta in western Java the population density is around 8000 per krn2. This contrasts with less than nine people per km- on Sulawesi (Fig. I)."

Jan 1, 1992

By L. A. Bertram, F. J. Zanner

"The goal of this paper is to present a tool to simulate transient melting of the electrode tip. This capability is needed to develop and test furnace control algorithms since experimental determination is difficult and expensive. Simulation incorporates parameters (including arc voltage, arc current, electrode gap and furnace pressure) from previous quasi steady experiments with 460 mm diameter Inconel 718 electrodes.Cathode heating rates (determined by classical as well as experimental arc models) are linked to these independent variables. After radiative loss adjustments to the heating, transient one dimensional melting is computed. IntroductionThe vacuum arc remelting (VAR) process attempts to improve the physical and chemical homogeneity of a static-cast electrode by remelting and solidification in a quasisteady manner. To achieve steadiness of furnace operation requires automatic controls based on inputs measuring physically relevant state variables of the process. Previous industrial scale VAR studies (1,2,3) involving stainless steels, superalloys, and other alloys have provided a basis on which control strategies of some generality can be proposed (4). Of these measurements, the data for Inconel 718 is the most complete, so discussion in this paper is restricted to this alloy.Studies of the In 718 alloy subjected to the VAR process have established that melt rate M (kg/hr) depends not only on the melt current 1m (kA) supplied to the furnace, but also on ambient gas pressure of CO, PCO (micron), and electrode gap ge (mm) as well (1):"

Jan 1, 1986

By W. W. Adams

Increased employment and a lower accident-frequency rate were the outstanding features of the metal- and nonmetal-mining4 industries of the United States in 1939 compared with 1933, according to reports furnished by individual mining companies to the Bureau of Vines, United States Department of the Interior. Except for 1937, the reports for 1939 showed gains both in number of employees and number of mar -hours worked over all years since 1929. The accident-frequency rate per million man-hours of exposure to mining hazards was lower than in any year since 1925. Reports for 1939 revealed a total of 111,909 men employed in and about mines, an increase of inure than 8 percent over 1931 The total volume of labor performed at all mires was slightly more than 299 million plan-hours, an increase of mare than 10 percent over 1938. As these gains suggest, the average employee had a longer period of work in 1939, the increase amounting to r workdays per employee.

Jan 1, 1941

By A. A. Collins

H. R. BIANCO*—I should like to ask Mr. Collins if that statement he made about the addition of drosses to the blast furnace slowing down the blast furnace is a result of his own experience or a result of the experience of some older metallurgists; and perhaps I should ask him to define the type of drosses that he means. A. A. COLLINS (author's reply)— That has been my own personal experience with dross. On various occasions at Chihuahua we attempted to incorporate the dross in our regular blast furnace charge and to shut down the dross re-verberatory to try to save some money. As expected, we had very poor results. I think that Ed Fleming will well remember on one occasion, that was back about 1933, when we attempted the first experiment along this line, and as a result of the sulphur addition to the blast furnace to matte out the copper we ended up with hanging furnaces and mushy slags and abandoned the dross experiment, once again turning to the use of the reverbera-tory for handling dross. H. R. BIANCO—Is that dross you refer to from the drossing kettle ? A. A. COLLINS—Yes, the dross that I am referring to came from drossing kettles. Furthermore, to back up my previous assertion, I had occasion in 1943, while up at Leadville, to once again experience the routing of dross through the blast furnace with its sulphur addition, since they had no dross re-verberatory, and to observe that once thf dross was removed, the furnace was speeded up almost 100 tons a day. All of these are personal experiences and I think that Mr. Feddersen also has had a little experience along this line —in fact, I believe all of us have had some experience. H. R. BIANCO—I know at Trail they recirculate considerable dross through the blast furnaces and we also recirculate dross at Herculaneuin and I am not aware that it has done much towards slowing down the blast furnace. A. A. COLLINS—We have always had very poor results. In the first place you have got to add a sulphur addition to pick up that copper and once you do that, that sulphur is apt to combine with some of the zinc and you are going to form a little mush; before you know it you have furnace hangs and a poor working furnace. Now of course that depends on the amount of zinc you have on charge. But in 1943, Leadville had roughly about 7 pet zinc in their slag and it worked very poorly. Previously when they had 4 or 5 pet zinc in their slag it did not matter. B. L. SACKETT* At Tooele we had a great deal of experience with copper. We have always been able to keep a lead well, however, in spite of the fact we have run as much as 5 pet copper and only 15 pet lead on the charge. But regarding the handling of dross, our dross reverberatory furnace is only 7 or 8 years old. Before that we recirculated the dross through the furnace and thought we were doing a pretty nice job. Of course these things are all more or less relative—in other words you establish a certain condition much better than one of a few years ago and possibly as good as any other of which you know and you think you have pretty good results. When we first took the dross off of the blast furnace and put it through the dross reverberatory furnace we immediately found out that we had gained something very real in furnace speed. Since that time there have been occasions when, because of the dross reverberatory being down, we have had to use dross again through the blast furnace and that has checked our original experience in slowing down the furnace very definitely. So we feel that a dross reverberatory is a very valuable asset at the Tooele Plant. A. A. CENTER*—Mr. Sackett's being here reminds me of trying to run with a minimum of lead concentrates the maximum of dross producing electrolytic zinc plant residue. He came up from International Smelting Co. to help us get started on that. We took an old copper blast furnace at Great Falls, Montana, and made a lead furnace out of it by putting a lead well on the other long side which of course is a very unorthodox lead blast furnace. Our aim was to treat the residue from the electrolytic zinc plant, as I said, with a minimum of lead concentrates. That meant a maximum amount of dross. At that time selective flotation was not general practice, so our zinc concentrates ran relatively high in copper and other dross-producing elements; and of course these were largely in the zinc plant residue. I think we might call it muscle metallurgy, but we had an interesting, successful experience there and we ran for over a year thanks to Mr. Sackett's helping us get started. I have the details, but time does not permit. We did well enough so that the A. S. and R. Co. at East Helena kept boosting up the offer to us for the electrolytic zinc plant residue and there was not enough lead concentrate to supply two lead smelters there in Montana, so the matter finally finished up by the A. S. and R. Co. taking all of the residue under long term contracts.

Jan 1, 1950

By Alla D. Mah

The heats of combustion of three chromium carbides, Cr23C6, Cr7C3, and Cr3C2, were determined by combustion calorimetry. Heats of formation calculated from the results follow: ?Hf°298 (Cr23C6) = -94.7 ± 5.0 kcal/mole, ?Hf°298 (Cr7C3) = -43.3 ± 1.7 kcal/mole, and ?Hf°298 (Cr3C2) = -22.5 ± 0.8 kcal/mole.

Jan 1, 1969

By R. W. Guard

ALTHOUGH etching techniques have been developed for revealing dislocation sites in several metals and ionic crystals,h t is valuable to extend the technique to new metals. An etch pit method for nickel has been developed on the basis some suggestions of Dr. John R. Cuthill of the National Bureau of Standards who had observed etch pits in creep specimens of nickel. The etchant used was proposed first by wensch2 for revealing grain size in nickel. The present paper describes the evidence that the technique can be used to reveal dislocations and gives the conditions under which etching can be carried out. The specimens examined were vacuum melted high-purity Ni (99.985 pct Ni) and commercial "A" nickel (99.8 pct Ni). Both materials contained greater than 0.008 pet C and had been annealed in nitrogen or dry hydrogen at 1100o to 1200°C. This gave a grain size of 1.5 mm in the high-purity nickel and 0.050 mm in "A" nickel. Tensile specimens (0.254 in. diam) were deformed from 0.25 to 10 pct at room temperature and then heated for 1/2 hr at different temperatures from 400" to 900°C. The specimens were sectioned longitudinally then polished electrolytically in 60 pct H2SO4 and etched in 35 pct H3PO4 solution at 0.2 to 0.4 v for 30 sec to 3 min. The best method for setting the proper voltage for etching is to increase the voltage until gas bubbles are evolved vigorously from the specimen and then cut it back by 10 pct. It is necessary to heat the specimen above 500°C after deformation in order that etch pits will be formed. This "decoration" treatment permits carbon to segregate to the dislocation rendering them sensitive to etching. It was demonstrated that carbon was the decorating impurity by decarburizing some specimens in wet H2 at 1200°C. The susceptibility to etch pitting was lost following this treatment but could be restored by carburizing in contact with graphite. Some rearrangement of the dislocations in the as-deformed structure occurs on heating at 500oC and above so that the technique can not be used to study the nature of dislocation patterns in deformed specimens. Extended etching does not change the number of pits although the background becomes rough and the pits quite large. The polycrystalline specimens with various strains were examined after annealing at different temperatures. Typical patterns are shown in Figs. 1 and 2. In the unstrained specimen, Fig. 1, the density of pits is 2.5 X 10' per sq cm. All grains show pits regardless of their orientation although there is a

Jan 1, 1961

By Frederick A. Mumpton

Recent findings by medical workers on the association of certain zeolite minerals with the high incidence of pleural mesothelioma in two small Turkish villages have caused considerable excitement both in medical circles and in the synthetic and natural zeolite businesses. The 42 cases diagnosed between 1970 and 1977 in one community of 600 population in a region of altered volcanic tuff represent a virtual epidemic of this rare malignancy which normally strikes only about one person in a million. Cancer workers around the world expect that detailed environmental and epidemiological studies of the disease in these areas will shed considerable light on the cause of this particularly lethal form of lung cancer. Scientists and engineers developing uses for zeolite materials in industry and agriculture, however, are justly concerned that the preliminary results available on this situation will be used by environmental and regulatory organizations to label an entire group of miner- als as carcinogens on the basis of what is little more than circumstantial evidence. Although there is no question as to the large number of cases of mesothelioma in these areas of central Anatolia, the work to date has suffered from a lack of sound geological and mineralogical input. Ataman (1) stated that a "correlation" exists between mesothelioma and zeolites in this region; however, the geological data needed to document a direct relationship between the presence of zeolites in the volcanic tuffs surrounding the villages in question and the rate of malignant lung disease in the inhabitants have g been obtained, nor has evidence that suggests a cause-effect relationship between zeolites and cancer been reported. To provide fundamental information on the distribution of zeolite minerals in areas of central Turkey where high incidences of pleural mesothelioma have been reported and to evaluate from first-hand knowledge the published reports and news releases of medical workers engaged in assessing the problem, the following investigation was made.

Jan 1, 1979

By T. J. Langan, M. Ramajayam, T. Dorin

"6xxx-series Al alloys are the most commonly used alloys in the automotive industry as they have an appropriate balance of strength, corrosion resistance and formability. The main strengthening phase in these alloys is the ß’-Mg2Si precipitates. One opportunity to achieve stronger 6xxx-series Al alloys, without affecting corrosion and formability, is the use of Sc. The main challenge of using Sc in 6xxx-series lies in the heat treatment, which must be designed to allow for a fine precipitation of both Al3Sc and ß’-Mg2Si. In this work, two model alloys are used, an Al-Sc-Zr and an Al-Mg-Si-Cu-Sc-Zr, to explore the impact of the 6xxx-series key elements (Mg, Si and Cu) on the Al3Sc precipitates. Transmission electron microscopy and atom probe tomography are used to investigate the precipitates present in the microstructure after casting. We find that higher Si content results in the formation of dispersoids upon casting. The average composition of these dispersoids is (Al0.8,Si0.2)3 (Sc0.888,Zr0.024,Mg0.08,Cu0.008). A closer look at the solid solution reveals that most of the Sc and Zr is supersaturated after casting even in the presence of Mg, Si and Cu. We discuss the impact of these results on the design of a suitable heat treatment for 6xxx-series alloys with Sc.INTRODUCTION The most common strategy to strengthen aluminum (Al) alloys is by micro-alloying to form a fine distribution of precipitates (Gladman, 1999). Whilst precipitates enhance the strength, this is often done to the detriment of ductility and corrosion performance (Davis, 1999). The 6xxx-series Al alloys are heavily used in the automotive industry as they offer an appropriate balance of strength, ductility and corrosion resistance (W. S. Miller et al., 2000). The strength increment in these alloys comes from the formation of the ß’–Mg2Si and the quaternary Q’ phase (Chakrabarti & Laughlin, 2004; Polmear, St. John, Nie, & Qian, 2017). One opportunity to achieve stronger 6xxx-series alloys, whilst keeping good balance of corrosion resistance and formability, is the use of small additions of scandium (Sc). Sc is one of the most potent strengtheners in Al alloys (Dorin, Ramajayam, Vahid, & Langan, 2018; Røyset & Ryum, 2005). Most of the strengthening benefits from Sc come from the formation of fine Al3Sc dispersoids. The following strengthening mechanisms apply to Sc: 1) Solid solution strengthening, 2) precipitation hardening, 3) inhibiting recrystallization, 4) assisting nucleation of other strengthening phases (Dorin, Ramajayam, Lamb, & Langan, 2017). As compared to other dispersoid phases, Al3Sc dispersoids have good electrochemical compatibility with Al alloys and hence do not affect their corrosion resistance (Cavanaugh, Birbilis, Buchheit, & Bovard, 2007). The coarsening resistance of Al3Sc is often improved by adding zirconium (Zr), as it forms a Zr rich shell around Al3Sc which prevents Sc from moving across the interface."

Jan 1, 2018

By W. N. Carr, J. R. Biard, B. S. Reed

An analysis of the semiconductor injection laser is presented which is based on a phenomenological model using device and material parameters. The intent of the laser threshold analysis is not to predict from theory the actual threshold current density but rather to provide a logical means of interpreting experimental results. The device and material parameters have been selected such that they describe both the threshold conditions and quantum efficiency of the lasev. A technique is proposed whereby the current required to obtain a population inversion is predicted from device 1-V characteristics. Experimental data are presented which support the analysis. THIS investigation is concerned with the characteristics of GaAs lasers fabricated in this laboratory. However, the assumptions used in these calculations should not limit their application to GaAs alone. It is felt that the analysis is sufficiently general to be useful in describing the operation of other semiconductor-laser materials. ANALYSIS heavily doped semiconductors to be considered. The absorption and/or generation of optical radiation may be completely specified in terms of q(E) and the probability functions f,,(E) and f,(E) which define the occupancy of the valence-band and conduction-band levels, respectively. The symbols used in this analysis are listed at the end. Following the approach of all' it can be shown that the effective gain coefficient, g, in the plane of a forward-biased P -N junction is g(E)=-ai@)[1-fv(E)-fc(E)] [1I In particular Eq. [I] holds for the photon energy at which lasing occurs, Ep. Throughout the following discussion Eq. [I] is considered only for the lasing transition E = Ep. For simplicity the functional energy dependence of the various factors is omitted in subsequent equations. Unless otherwise stated the symbols used represent the values at Ep. If the analysis is limited to the P-type side of the laser junction, the function q(l -f,,) is recognized as the band-to-band absorption in the P-type material at thermal equilibrium. Under forward-bias conditions the function f, is determined by the electron quasi Fermi level in P-type material. For sufficiently large forward bias the second term in Eq. [3] will become dominant and net gain will result; i.e., g will become positive. In order to simplify the subsequent analysis several assumptions are in order at this point. a) No conductivity modulation occurs. /„ is independent of f, and therefore go is a constant. b) The P-type material is heavily doped such that the degeneracy of the valence band permits popu-

Jan 1, 1964