Search Documents

By Andrew Artzer, Michael Moats, Jack Bender

Antimony and bismuth in copper electrorefining electrolytes can cause cathode contamination, leading to the careful control of their concentrations. This study examined the laboratory scale removal of bismuth and antimony from an electrorefining electrolyte using a solvent extraction mini-pilot plant. The ability of a proprietary phosphonic acid ester extractant (REX-2) in a commercial diluent was studied in a simulated commercial setting. Antimony and bismuth were both extracted effectively from the electrolyte (72% Bi and 70% Sb removed) and Bi was effectively stripped (92% Bi recovered) with 400 g/L sulfuric acid. A final strip solution was obtained from the SX circuit containing 0.36 g/L Bi, 0.043 g/L Sb, 1.3 g/L Cu, and 0.18 g/L As. Unfortunately, most of the extracted Sb remained in the organic phase. Following the pilot study, experiments were performed to examine the precipitation of bismuth from the aqueous strip phase and the removal of antimony loaded on to REX-2. INTRODUCTION For many years, antimony and bismuth have been some of the most problematic impurities in copper electrorefining (ER) (Bardwell & Lapee, 1933). Along with surface roughening, high concentrations of Sb and Bi can contaminate the copper cathode and precipitate at the copper grain boundaries. This drastically reduces the drawing ability of the metal (Bender & Emmerich, 2016). For these reasons, it is necessary to control Sb and Bi concentration in the cathode, which is done by controlling their concentration in the electrolyte. Conventionally, Sb and Bi concentrations are controlled by maintaining a proper As/(Sb+Bi) molar ratio in the anode and arsenic concentration in the electrolyte. Antimony and bismuth are removed during electrolyte purification using liberators (electrowinning cells) and/or ion exchange. Liberators treat an electrolyte bleed stream from the ER circuit and electrodeposit increasingly impure copper as the copper concentration of the solution decreases. Traditionally, first stage liberators reduce the copper concentration from ~45 g/L to ~15 g/L and produce saleable copper. Second stage liberators decrease the copper concentration to ~8 g/L (Biswas & Davenport, 1980) which results in contaminated cathode that is returned to anode production (Biswas & Davenport, 1980; Wang, 2004). Further electrolyte purification is not always required but third stage liberators can be used to reduce copper concentration below 2 g/L which results in significant removal of As, Sb and Bi and very impure deposits which are recycled to a smelter or used for As production. However, liberators do not have very high energy efficiency (Acharya, 2014; Ando & Tsuchida, 1997) and below 0.5 g/L copper, highly toxic arsine gas may form (Biswas & Davenport, 1980).

Jan 1, 2019

By Matthew Tunnicliffe, Akram Alfantazi, Paul Nesbitt, Farzad Mohammadi

"Lead and its alloys are proper candidates for anodes in electrowinning processes mainly because they are insoluble in the leach solutions and relatively cheap. However, the annual cost of corrosion problems associated with these anodes is millions of dollars. In this study lead-silver and lead-calcium anodes were tested under typical nickel electrowinning conditions and the effect of chloride on the corrosion performance of the anode materials was investigated. Corrosion rates of the anodes were calculated using the discharge plateau (reduction of lead dioxide to lead sulfate) after galvanostatic experiments. It was found that lead calcium anodes have the highest corrosion rate both in the presence and absence of chloride. Surface morphology of the electrodes was studied using SEM and the corrosion products were characterized using XRD.IntroductionLead (Pb) is usually the preferred material for commercial anodes since it is insoluble in the leach solution and the costs are manageable. One advantage of using an insoluble material as an anode is the higher purity of the cathodic deposits and better quality of the end product. During nickel electrowinning, metallic nickel is deposited on the cathode while oxygen evolution reaction (OER) takes place on the anode. In practice, relatively high potentials are necessary for the reaction to proceed at the desired rate because of the high overpotential of OER on lead. Lead anodes get oxidized in typical electrowinning conditions and usually have two to three years of lifetime. Although the price of each anode is insignificant, the overall cost of corrosion of these anodes is considerable, which is due to the large number of anodes used in a plant, typically two to three thousand. Therefore, corrosion is a significant problem associated with lead anodes in commercial nickel electrowinning plants and industries show interest in addressing this problem. Corrosion of lead electrodes in acidic environments has been previously the subject of many research studies [I-7]. It has been reported that, during the anodic polarization of lead, several phases may be present on the surface, depending on the potential range that is being studied [8]. Lander showed that lead is oxidized at potentials higher than 0.252 YsHE with tetragonal lead monoxide being the main reaction product [9]. At 0.666 YsHE lead can transform to lead dioxide; however, it is not stable and transforms to lead sulfate and lead oxide. At potentials higher than 1.684 YsHE, lead dioxide is eventually a stable phase and forms a protective layer on the surface [I 0, 11]. Under conditions of a typical nickel electrowinning plant, usually a 200 A/m2 current density is passed through the electrodes."

Jan 1, 2012

By Philip C. Tully

These modifications to the Redlich-Kwong equations for pure hydrogen and neon were developed after an unsuccessful attempt to generalize a modification technique previously developed for helium. New coefficients of the B terms were developed by minimizing the residuals. No changes were made in the coefficients of the A terms. For normal hydrogen, B was changed to [0.08063Tc PcT] for temperatures from 980 to 423° K and pressures up to 1,050 atm. The average deviation in Z was 0.36 percent with maximum deviations less than 1 percent for all but a few low-temperature points. For neon, B was changed to [PCT 0.1025T], for temperatures from 120° to 973° K and pressures up to 1,500 atm. The average deviation in Z was 0.34 percent with maximum deviations less than 1 percent for all but a few high-pressure and low-temperature points. Efforts to attain a lower temperature range to comparable accuracy with this type of modification were unsuccessful. In the range of applicability, these equations should be used with caution when calculating derived thermodynamic functions, such as the isobaric specific heat.

Jan 1, 1968

By H. L. Ford

Flocculant testing should be initiated for economic or performance reasons. When the decision has been made to test, the laboratory can provide valuable information concerning the various products under consideration. Properly conducted laboratory tests can determine: 1. If two flocculants are needed to achieve clarity or density. 2. Ease of mixing. 3. How quickly the material goes into solution. 4. Stability of prepared f locculant solution. 5. Stability of the floc formed. 6. Amount of mixing required for proper floe formation. 7. Optimum flocculant concentration. 8. Optimum pulp density. 9. Approximate location of the point of addition. 10. Single or multiple addition points. When a flocculant shows promise in the laboratory, a plant test should be scheduled. During the plant trial, arrange for normal conditions and start testing with a crew that is most familiar with the unit operation where the flocculant will be applied.

Jan 1, 1986

By Shunichi Ajima

PT. Smelting Co. was established in February, 1996 to construct and operate the Gresik Smelter and Refinery. The construction work of first Copper Smelter and Refinery in Indonesia was completed in the end of August, 1998 and it was put into the integrated test operation in December, 1998. Gresik Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from copper concentrate supplied from Grasberg Mine of PT. Freeport Indonesia Company in Irian Jaya, Indonesia. As by product 592,000 tpy of sulfuric acid, 382,000 tpy of slag, 31,000 tpy of gypsum and 480 tpy of slime will be produced in the full operation. Major processes applied at Gresik Smelter and Refinery are: Smelter: Mitsubishi Continuous Copper Smelting and Converting Process ( Mitsubishi Process ) Anode Casting: Continuous Casting of Copper Anodes with the Hazelett Twin Belt Caster Refinery: ISA Process Acid Plant: Lurgi Mitsubishi Double Contact Process

Jan 1, 1999

By John Chipman, Raymond L. Orr

Recently reported high -temperatlnre thermal data have been incorporated in a reuieu' of the therinody-r~ar,zic propesties of iron. The recent data permit mot corlsisterlt and reliuble choices to be made for many of the pvoperties, resnlling in bettev eslablished tabrtlations of the thermodynamic functions. Values of Cp, h°t- - H°298. s°t - S2sa, and (G°T -H298/T are tabulated for -the solid and liquid phases of iron in both stable and melastable regions. Consistency of the tabulations has been maintained to the precision necessr~vg to yield the Gibbs energy change belween the bcc (a, 8) and fcc (y) phases of iron at temperatures pertinenl to alloy studies. THE importance of the metal iron has stimulated many investigations of its thermodynamic properties at elevated temperatures. Reviews and summaries of the data have appeared from time to time. Among these the 1951 paper of Darken and smith' deserves highest recognition for the quality of its criticism and for the precision and thermodynamic consistency of its tabulations. These and the more recent table of Kaufman, Clougherty, and weiss2 reproduce the Gibbs energy of the (a, 6)--Y transformation with sufficient sensitivity for alloy studies. Other recent compilations of equal validity3-' make no attempt to do this. Since this Gibbs energy change is not greater than 22 cal per g-atom over the temperature range 1100° to 1800°K, it is obviously desirable to tabulate values of (G°t - H298)/T to four places of decimals even though the absolute accuracy would not warrant such precision. The necessity for reconsideration of the problem is emphasized by the recent publication of several important researches on the enthalpy and heat capacity of iron. The older work is well-covered in the reviews cited and will be mentioned here only when actually employed in the tabulations. GAMMA IRON Transition temperatures are taken from the selec -tions of Elliott and Gleiser,5 based on the work of Boulanger7 and earlier workers. For the a-y (A3) transition at 1184°K we retain the value 215 cal per g-atom adopted by Darken and smith.' It has received confirmation in the recent work of Dench and Kubaschewski,' and of Braun8 using adiabatic calori-metry, and of Wallace, Sidles, and Danielson10 using a pulse heating technique. The enthalpy data of Olette and ferrier" and of Anderson and Hultgren12 at higher and lower temperatures may be extended to 1184°K to give the following values which are adjusted to the required value of ? 1184 Ha,1184 Ha 298 = 8030 cal per g-atom [11 hr,1184-ha298 = 8245 cal per g-atom [2]

Jan 1, 1968

By Glenn A. Keep

THIS paper is not an announcement of the successful conclusion of the Cerro de Pasco Copper Corporation's pacos-pyrite problems, but merely a description of the commercial-scale, intermittent-roasting operations conducted by the writer, J. H. Lucas and others of the staff. It was prepared by request, for presentation at the February meeting of the Institute. The results obtained in Peru confirm the 1-ton-a-day experiments completed about three years ago at Kearny, N. J. by C. C. Gordon and Mr. Lucas, where it was first demonstrated that a mixture of about 80 per cent. pacos ore with 10 per cent. pyrite ore and 10 per cent. salt could be roasted intermittently in a small 1-ton-a-day Holt-Dern furnace without extraneous fuel, producing porous calcine that could be leached rapidly. Mr. Keep and his staff, by successfully introducing improvements in the construction of the commercial furnace and in their handling of material, have established beyond doubt a low cost for roasting. The other steps in the process of treating pacos and pyrite ores have not as yet been demonstrated as sufficiently conclusive to warrant their acceptance for a permanent plant. Cerro de Pasco Ores The ores of the Cerro de Pasco Copper Corpn. at Cerro de Pasco, Peru, are situated at an altitude of 14,000 ft. The town and mines are served by the Cerro de Pasco Railroad, which operates between Cerro de Pasco and Oroya, the site of the company's copper and lead smelters. Table 1.—Average Analysis of Cerro de Pasco Ores Pacos Ore Pykite Ore Silver, oz............................................... 10.3 12.0 Gold, oz................................................ 0.007 0.01 Lead, per cent........................................... 1.7 1.8 Copper, per cent......................................... 0.19 0.27 Zinc, per. cent........................................... 1.4 1.02 Iron, per cent........................................... 13.4 34.45 Silica, percent.......................................... 61.8 24.5 Alumina, per cent....................................... 2.5 0.62 Lime, per cent........................................... 1.5 0.20 Manganese, per cent..................................... 0.42 0.09 Sulfur, per cent,.......................................... 1.1 34.2

Jan 1, 1929

Executive A. R. LEDOUX, Chairman GEORGE D. BARRON SIDNEY J. JENNINGS J. V. N. DORR J. E. JOHNSON, JR.¬ Membership J. E. JOHNSON, JR., Chairman KARL EILERS F. F. SHARPLESS R. M. RAYMOND LEWIS W. FRANCIS Finance J. V. N. DORR, Chairman CHARLES F. RAND J. V. W. REYNDERS Library E. GYBBON SPILSBURY,' Chairman ALEXANDER C. HUMPHREYS GEORGE C. STONE' JOHN H. JANEWAY BRADLEY STOUGHTON Papers and Publications BRADLEY STOUGHTON, Chairman

Jan 1, 1923

By John E. Husted

Quantities of kaolin in Georgia in-contiguous or single bodies had been established by previous work to be sufficient for an alumina industry. The need for characterization of this kaolin to determine its suitability as an ore of aluminum resulted in the studies described herein. It was determined in an area roughly 7 x 27 miles, known as the Wrens district that approximately 5.9 billion short tons of kaolin averaging 35.55 percent A1203 exist in an essentially continuous clay body. The Macon-Sandersville district consists of discontinuous kaolin bodies averaging 35.28 percent A1203 with an average thickness of 28 feet. Tonnages for this district are not available. One hundred and twenty core samples of kaolin were analyzed for K20, CaO, MgO, Al203, T102, Cr203, Fe203, Si02, P205, and F. The P205 and F were analyzed by wet chemistry methods and the others by electron microprobe. Seventy-nine of the samples were from the Wrens district forty from the Sandersville-Macon district and one from the Andersonville district. Emission spectroscopic analyses were also made to qualitatively determine all elements present for each core. X-ray diffraction studies were made of each core to determine mineral species present. Scanning and transmission electron microscope pictures also are given for each I' core sample. Elevations, overburden thickness, and kaolin thickness are given for each core site as well as map locations. Isopachs for over-burden and kaolin thickness are given for the Wrens district.

Jan 1, 1983

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the SrF2-Y2O3 system for which liquidus and solidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. The phase diagram was constructed from information obtained by ceramogra¬phy, X-ray diffraction, thermal analysis, and electron probe microanalysis of small specimens encapsulated in platinum-20 percent rhodium or molybdenum ampoules. The data indicate a simple eutectic system with limited terminal solid solubilities. The eutectic temperature is 1,457°±5° C, and the eutectic composition is 4±1 mole-pct Y203. Strontium fluoride containing up to 2 wt-pct 0 2 was studied to determine the effects of oxygen contamination. Oxygen levels in excess of 0.2 wt-pct resulted in eutectic formation between SrF2 and SrO. The eutectic composition is between 0.2 and 0.7 wt-pct 02, and the eutectic temperature is 1,447°±5° C. No intermediate oxyfluoride phases were detected.

Jan 1, 1974

By S Sims, A Stradl, G Hope, B Lacouture

Column flotation cells have been installed in numerous base metal operations around the world. The majority of these cells utilise conventional air-only spargers to introduce air into the bottom of the column. The recent development of instruments to measure the bubble characteristics in these columns has provided a renewed understanding of column behaviour. These new tools provided insight into why the columns at Red Dog Mine had never performed up to expectations. After efforts to optimise the spargers failed to substantially change the bubble size and air efficiency, alternate sparger systems were investigated. The Metso Minerals CISA Microcel sparger system appeared promising and was selected for a full-scale plant trial. The Microcel sparger system was originally developed for the coal industry at the Virginia Centre for Coal and Minerals Processing. In October 2003, a Microcel was retrofitted into one of two 3.66 m diameter flotation columns in the zinc retreat circuit at Red Dog Mine. The operation of the two different sparger systems in parallel allowed a detailed comparison. This paper discusses the performance of the Microcel based on the data collected during several detailed surveys. Bubble size measurements carried out in the pulp zone using the McGill University bubble viewer showed a significant difference in bubble size. The mean Sauter diameter of the bubbles decreased from 3.4 mm for the jetting-type sparger to 1.9 mm for the Microcel sparger. The overall recovery and the recovery by size fraction for both valuable and gangue minerals were compared. Paired t-tests demonstrated that the Microcel column produced a higher concentrate grade (0.6 per cent zinc absolute) and a higher unit recovery (2.8 per cent zinc absolute) than the existing Canadian Process Technologies Inc (CPT) SlamJet column. These improvements provided a payback period of 1.5 months for the $109 000 investment.

Jan 1, 2005

By B. C. Wonsiewicz, W. W. Wilkening

Following a procedure proposed by Wheeler and Ireland, Plane stress yield loci were constructed from Knoob hardness numbers. Basically, six differently oriented hardness measurements were made on three orthogml surfaces through pure poly crystalline magnesium sheet, a magnesium single crystal, and sheet of the magnesium alloys: Mg + 0.5 pct Th, Mg + 4 pct Li, AZ31B, and EKOO. Hardness loci were found to be in poor agreement at small strains (E < 0.05) with loci established by a more rigorous technique. At larger strains (E - 0.10) the agreement is fair, but at this stage in deformation the conventional locus has lost much of the asymmetry that characterizes these anisotropic materials. Two effects which will lead to distortions in the Khn locus are discussed with reference to the geometry of plastic flow during a hardness test. DETERMINING a material&apos;s resistance to multiaxial loading is of interest not only from a structural design viewpoint but also from that of deformation processing. Unfortunately, the determination of the yield locus, although simple in principle, involves tedious procedures if the results are to be at all rigorous.&apos; The idea, first proposed by Wheeler and 1reland2 of determining the yield locus by means of six Knoop hardness impressions along the principal directions in a material has obvious appeal. It is simple, quick, and should be applicable to very thin sheets. If such a technique could be demonstrated to produce consistently reliable results, it would be of interest to both researcher and designer. Lee, Jabara, and ackofen have compared the yield locus determined by Knoop hardness measurements (the Khn locus) to a locus determined by more rigorous techniques. They found good agreement for two titanium alloys at a plastic strain of about 1 pct. The purpose of this paper is to investigate if the Khn locus construction is a reasonable approximation to the locus of a highly anisotropic material. Examples of such materials are magnesium and magnesium alloys which have severely distorted yield loci which in turn reflect markedly dfferent yield strength in different directions.&apos; In pure magnesium, for example, the yield stress in tension along the transverse direction may be four times the yield stress in compression in the same direction and twice the tensile yield stress in the rolling direction. Predicting such large differences ought to serve as a severe test of the Khn locus construction. EXPERIMENTAL PROCEDURES Samples of rolled sheet, 0.250 in. (6.35 mm) thick, of pure magnesium and four magnesium alloys (Mg experimental materials. The pure magnesium together with the lithium and thorium alloys were those used in the study of Kelley and Hosford. The grain size was ASTM number 4 for the pure magnesium and number 6 for the alloys. HARDNESS TESTING The materials were sectioned along the rolling and transverse planes, mounted in a quick setting resin, and mechanically polished. Most of the hardness tests were performed on a surface prepared by electro-polishing (30 pct nitric acid in methanol at 0°C and 20 v) with the exception of the AZ31B and EK00 alloys which were made directly on a metallographically polished surface. However, subsequent hardness tests on the same sample after heavily electropolishing, revealed essentially the same hardness as before. At least twenty Knoop hardness impressions under a 100-g load were made in each of the six orientations shown in Fig. 1. The average hardness number and standard deviation were then calculated for each orientation. CONVENTIONAL LOCUS CONSTRUCTION Yield loci were constructed using a technique described in detail by Lee and ackofen,&apos; in which the flow stress (stress at a given plastic strain) fixes the coordinates of a point on the locus and measurements of the strain ratio serve to establish the slope of the locus at that point. The loading paths which correspond to uniaxial tension or compression tests establish the four intercepts of the locus with the coordinate axes plus one point on the balanced biaxial tension line Tensile testing was performed along the rolling and transverse (r, t) directions. Samples had a uniform rectangular gage length 1 by 4 by 4 in. (25.4 by 6.35 by 6.35 mm) and were deformed at a strain rate of 3.33 x 104 sec-&apos;. The tests were interrupted periodically to unload the sample and measure the plastic strains by means of X-Y post yield strain gages. Compression tests in the rolling, transverse, and through-thickness (r, f, z) directions were performed on 1/4 in. (6.35 mm) cubes at an initial strain rate of 8.33 x sec-&apos;. Lubrication was provided by 0.002 in. (51 pm) Teflon sheet which was renewed after unloading for micrometer measurements used to calculate the strains.

Jan 1, 1970

By Charles Winter

The Ohio Department of Transpor- tation's (ODOT's) $228 million 1-480 Valley View Bridge project was needed to keep traffic flowing on one of the state's busiest freeway segments. Deterioration from age and steady high- traffic volumes necessitated the replacement of the existing decks of the I-480 east- and west-bound bridges over the Cuyahoga River Valley in suburban Cleveland. To facilitate this work without creating tremendous backups and traffic delays due to long-term lane closures, the project included design and construction of a new four-lane bridge in the median gap between the existing 1-480 bridges. Now complete, the new center bridge allows for all four lanes of I-480 to be maintained in each direction while deck replacement and other repairs are made to the existing bridges, while also providing increased capacity after project completion. ODOT awarded the project to the Walsh Design-Build Team (DBT) in late 2017. This article describes how the Walsh DBT, with Jacobs Engineering as the DBT lead design firm, incor- porated an innovative approach to the design and construction of the driven pile foundations for the new I-480 center bridge. I-480 crosses approximately 200 ft (60.9 m) above the Cuyahoga River Valley. With an overall length of 4,150 ft (1,265 m) and spans ranging from 180 to 300 ft (54.8 to 91.4 m), the design and construction of the foundations for the new center bridge were critical to the success of the project. Due to their overall height and span lengths, the foundation loads for a typical pier consisted of a factored vertical load of 22,000 kips, (100 MN) plus significant overturning forces due to horizontal loads and thermal effects.

May 1, 2022

By Matthew Preedy, Brett Campbell, Jim Rush, Alan Howard, Derek Penrice

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2018

By L. H. Van Loon, E. G. Crayston, A. F. Heather

"IntroductionTHE PROPERTY of Madsen Red Lake Gold Mines. Limited. comprises fifty-eight claims located between Russet and Faulkenham lakes in Baird and Heyson townships of the Patricia portion of the District of Kenora. The mine is seven miles •by road from the hamlet of Red Lake. This latter centre is .connected to the Trans-Canada Highway at Vermillion Bay, Ontario, by provincial highway No. 105 which has a total length of one hundred and thirteen miles.The Madsen property went into production on August 11th, 1938, with a milling plant rated at 300 tons per twenty-four hours. Changes made in the crushing plant during October, 1938, allowed a •finer feed to be delivered to the mill and increased the milling •capacity to 400 tons per twenty-four hours. During 1948, steps were taken to add an additional 400-ton capacity unit to the milling plant. This latter work was completed by May, 1949, giving the present total milling .capacity of 800 tons per twenty-four hours.It was realized in the early 1940's that, eventually, considerable material suitable for backfilling in the mine would be required. As there were no large deposits of gravel or sand anywhere near the mine, officials of the Company considered it advisable to investigate the feasibility of using mill tailings for mine •backfill. Since Madsen mill tailings contain approximately 80 per •cent of minus-200-mesh material, it was not considered practical to use them for underground backfill without first removing the finer material. as the slimes present in a product of this fineness would without doubt preclude any drainage whatsoever. Table I gives a sizing analysis of Madsen mill tailings and Table II a quantitative chemical analysis of the ore."

Jan 1, 1954

By M. Hancer

The sign of the surface charge of selected potassium soluble salt minerals namely KClO4 , K2SO4 , KNO3, and KCl was determined from nonequilibrium electrophoresis measurements and found to be negative for each of the salt. Dodecylamine flotation of these salts revealed that the concentration of amine required for flotation increases in the order KClO4< K2SO4< KNO3<KCI. Precipitation of the amine collector colloid was not required for flotation of the oxyanion salts and in this case it appears that adsorption of the dodecylamine cation is sufficient to create the hydrophobic surface state. The order for flotation is explained in terms of surface hydration of these respective potassium salts based on contact angle measurements and FT Raman spectroscopic characterization of water structure.

Jan 1, 1999

By Aureal T. Cross

THIS paper is a review of the published literature on research in coal geology, principally exclusive of resource studies, which appeared or became available during 1950 and the latter part of 1949. This report is not to be construed as being complete. The papers referred to in the bibliography are those among many more, which were read either in full or in abstract. Undoubtedly other papers were published which either escaped the author&apos;s notice or were not available to him. Those which were seen in abstract only (about one fourth of those listed) were not available in time for the inclusion of more than a notice. An outline of all papers listed in the bibliography has been arranged by subjects and reasonable subdivisions with some papers cited under more than one subject. Most papers are indexed according to the principal subject of discussion or research only as to an unusual or noteworthy section of the entire report. There will likely be some disagreement as to the quality or merit of some of the papers selected and the specialist may be supercritical of the outline or organization of papers in his field. It may be that attention has occasionally been drawn to papers reporting old information or conclusions of questionable value. Conferences and Meetings One of the best indications of the growing interest in coal geology problems in the United States is the increasing number of times this field has been the focus of attention at conferences and meetings. Notable among these are the joint meeting of the Society of Economic Geologists and the Geological Society of America at El Paso, November 1949, at which the principal thesis was concerned with low rank carbonaceous fuel deposits, especially of western United States. Among the papers given which are already available were those presented by Barghoorn,&apos;" Parry? Roe? and Parks."&apos; At the annual meeting of the Botanical Society of America in New York, December 1949, a joint meeting of the Paleobotanical and Microbiological Sections was held for which a symposium on Microbiology in Relation to the Geologic Accumulation of Organic Complexes was organized. Publication of the six papers presented by Ralph G. H. Siu, Elso S. Barghoorn, Irving Breger, Claude E. ZoBell, James M. Schopf, and A. C. Thayson is anticipated. At the regular meetings of the Paleobotanical Section at the same time, several other papers of interest reported on coal ball studies, partial coalification of petrified wood, and floras. In Chicago, April 1950, a symposium on Applied Paleobotany was held by the Society of Economic Paleontologists and Mineralogists in conjunction with the American Association of Petroleum Geologists. The five papers presented at this meeting dealt with the use of Paleozoic plant microfossils for stratigraphic work, J. M. Schopf, Devonian-Missis-sippian fossils of the black shales, Aureal T. Cross, Mesozoic plants of stratigraphic value, Th. Just, plant microfossils of the Tertiary, L. R. Wilson, and studies of the Brandon lignite, Elso S. Barghoorn. Early publication of these in the Journal of Paleontology is expected. The Nova Scotia Research Foundation and the Nova Scotia Dept. of Mines sponsored an excellent 3-day conference in June 1950, which dealt with several aspects of coal geology. Papers on coal classification, P. A. Hacquenbard, structure and sedimentation problems in Nova Scotia, T. B. Haites, new techniques of thermal analysis, W. L. White-head, geochemical investigations of Nova Scotia coals, Irving Breger, the role of fossil plant spores in coal correlation and the stratigraphy of the coal-bearing strata of the Appalachian Region, Aureal T. Cross, were given. Some discussions of these papers by those in attendance were recorded, and the entire proceedings is being prepared for publication. In September 1950, an unusual 3-day field conference was held by the Ohio and West Virginia Geological Surveys under the sponsorship of the Coal Geology Committee. This study of the stratigraphy, sedimentation, and nomenclature of the Upper Pennsylvanian and Permian coal-bearing strata of southeastern Ohio, southwestern Pennsylvania, and northern West Virginia was augmented by two discussions on associated rocks (clays and shales) and stratigraphic nomenclature at Wheeling and Morgantown, West Va. An extensive guidebook was prepared, and transcriptions of the Morgantown meeting were made. As a follow-up of the September field conference, a round-table discussion was held on this general topic at a special open meeting of the Coal Research Committee in conjunction with the November meeting of the Geological Society in Washington. Short prepared statements to invite discussion were given on each of several topics by L. M. Cline, Carl 0.

Jan 1, 1953

By Aureal T. Cross

THIS paper is a review of the published literature on research in coal geology, principally exclusive of resource studies, which appeared or became available during 1950 and the latter part of 1949. This report is not to be construed as being complete. The papers referred to in the bibliography are those among many more, which were read either in full or in abstract. Undoubtedly other papers were published which either escaped the author&apos;s notice or were not available to him. Those which were seen in abstract only (about one fourth of those listed) were not available in time for the inclusion of more than a notice. An outline of all papers listed in the bibliography has been arranged by subjects and reasonable subdivisions with some papers cited under more than one subject. Most papers are indexed according to the principal subject of discussion or research only as to an unusual or noteworthy section of the entire report. There will likely be some disagreement as to the quality or merit of some of the papers selected and the specialist may be supercritical of the outline or organization of papers in his field. It may be that attention has occasionally been drawn to papers reporting old information or conclusions of questionable value. Conferences and Meetings One of the best indications of the growing interest in coal geology problems in the United States is the increasing number of times this field has been the focus of attention at conferences and meetings. Notable among these are the joint meeting of the Society of Economic Geologists and the Geological Society of America at El Paso, November 1949, at which the principal thesis was concerned with low rank carbonaceous fuel deposits, especially of western United States. Among the papers given which are already available were those presented by Barghoorn,&apos;" Parry? Roe? and Parks."&apos; At the annual meeting of the Botanical Society of America in New York, December 1949, a joint meeting of the Paleobotanical and Microbiological Sections was held for which a symposium on Microbiology in Relation to the Geologic Accumulation of Organic Complexes was organized. Publication of the six papers presented by Ralph G. H. Siu, Elso S. Barghoorn, Irving Breger, Claude E. ZoBell, James M. Schopf, and A. C. Thayson is anticipated. At the regular meetings of the Paleobotanical Section at the same time, several other papers of interest reported on coal ball studies, partial coalification of petrified wood, and floras. In Chicago, April 1950, a symposium on Applied Paleobotany was held by the Society of Economic Paleontologists and Mineralogists in conjunction with the American Association of Petroleum Geologists. The five papers presented at this meeting dealt with the use of Paleozoic plant microfossils for stratigraphic work, J. M. Schopf, Devonian-Missis-sippian fossils of the black shales, Aureal T. Cross, Mesozoic plants of stratigraphic value, Th. Just, plant microfossils of the Tertiary, L. R. Wilson, and studies of the Brandon lignite, Elso S. Barghoorn. Early publication of these in the Journal of Paleontology is expected. The Nova Scotia Research Foundation and the Nova Scotia Dept. of Mines sponsored an excellent 3-day conference in June 1950, which dealt with several aspects of coal geology. Papers on coal classification, P. A. Hacquenbard, structure and sedimentation problems in Nova Scotia, T. B. Haites, new techniques of thermal analysis, W. L. White-head, geochemical investigations of Nova Scotia coals, Irving Breger, the role of fossil plant spores in coal correlation and the stratigraphy of the coal-bearing strata of the Appalachian Region, Aureal T. Cross, were given. Some discussions of these papers by those in attendance were recorded, and the entire proceedings is being prepared for publication. In September 1950, an unusual 3-day field conference was held by the Ohio and West Virginia Geological Surveys under the sponsorship of the Coal Geology Committee. This study of the stratigraphy, sedimentation, and nomenclature of the Upper Pennsylvanian and Permian coal-bearing strata of southeastern Ohio, southwestern Pennsylvania, and northern West Virginia was augmented by two discussions on associated rocks (clays and shales) and stratigraphic nomenclature at Wheeling and Morgantown, West Va. An extensive guidebook was prepared, and transcriptions of the Morgantown meeting were made. As a follow-up of the September field conference, a round-table discussion was held on this general topic at a special open meeting of the Coal Research Committee in conjunction with the November meeting of the Geological Society in Washington. Short prepared statements to invite discussion were given on each of several topics by L. M. Cline, Carl 0.

Jan 1, 1953

By Herbert H. Einstein

The innate variability of natural materials and processes causes uncertainty in the models representing the natural phenomena and uncertainty in estimating the parameters that are used in these models. Reliability analyses, in contrast to the traditional factor of safety approach, are well suited to a rational incorporation of uncertainty in design and exploration decisions. Probabilistic kinetic and kinematic analyses were developed and combined to form reliability analysis methods. With one method the reliability, i.e.) the probability of failure, of an individual 2-plane wedge in a slope can be determined. The other method is aimed at slopes with a single slope parallel set of joints. In each case two approaches were developed, an encompassing one relying on computer codes and a simplified or summary approach relying on charts or pocket calculator computation. A major contribution of these approaches is the treatment of joint persistance. Instead of having to assume a certain persistence, it is now possible to use exploration data on joint geometry and to include the persistence effect rigorously.

Jan 1, 1979

By Q. H. Bui

The elastoplastic self-consistent model is one of the effective models to study the initial microstructure effect on the mechanical behavior of bulk materials. However, the use of this micromechanics-based model which takes into account only the Hall-Petch relationship at grain level for predicting the grain sized effects on the strength of the deformed materials is not accurate yet because of the fact that the dislocation density contributes also to the strengthening of this kind of materials. In this study, a modification made to the Hill-Hutchinson elastoplastic self-consistent model was proposed for investigating the microstructure dependence of the mechanical behavior of cold-drawn 6063 aluminium tubes. Because of the novel modification, an estimation procedure with two steps was required to identify the parameters of this micromechanical model. An acceptable agreement between experimental and theoretical stress-strain curves was achieved.

Jan 1, 2011