Search Documents

By Érica Linhares, Anderson Silveira Lopes, Aline Costa

In the production units of ferromanganese alloys wastewater are generated. They mainly arise from gutters of drainage water from warehouse of raw material (manganese ore, reducing agents and other), product and slag. This wastewater, in general, may contain particles that will suffer difficulty to naturally decant, giving the water turbidity and color characteristics. Thus, this study aims to characterize the effluent, the treated water and the sludge from the sedimentation tank from the one main Brazilian plant. The investigated characteristics were: turbidity, total solids (TS), suspended solids (SS), dissolved solids (DS), pH, Eh, COD (chemical oxygen demand), residue classification and chemical analysis by ICP - OES. The turbidity before treatment was 417 NTU and after passing through the tank, 44 NTU, a figure slightly higher than the emission standards for Class 1 regulated by the Brazilian environmental legislation in force. The values for TS, SS and DS of the effluent were 225, 114.3 and 110 mg/L, respectively. For the treated water the values were 93, 48.3 and 45 mg/L for TS, SS and DS, respectively. The sedimentation process was able to reduce by 21 % of the COD. In the test of loss on ignition (LOI) from the tank bottom sludge were observed losses of 29.35 %, while the volatile analysis found 20.70 % of volatiles in the sample. It was determined that the concentrations of Al, Fe, Mn and S are, respectively, 0.1875 mg.L-1, 0.3071 mg.L-1, 0,789 mg l-1 and 0.00828 mg.L-1, values above the maximum allowed by law. Based on the analysis of X-ray diffraction, the identified minerals in the sludge were quartz, muscovite, kaolinite, calcite and albite.

Jan 1, 2014

Production scale experiment study was carried out in a limestone open-pit for testing the theory and method proposed by the author(Zou, 1987). The results of experiments indicate that the mathematical model and computer programs, which include the consideration of both the three dimentional distributions of the weak planes and the energy densities of explosion stress waves, reflect the physical process of rock bench blasting quite well. The predicted fragment distributions coincide well with the practical fragment distributions measured with the photo-image analysis method proposed by the author(Zou,1989). The paper "A Three Dimensional Mathematical Model for Calculating the Rock Fragmentation by Bench Blasting in the Open-pit"(Zou,1987), which was published in some conferences and journals, has interested some scholors and researchers. In order to test and improve the model, a group of production scale experiments were carried out in a limestone open-pit during 1986-1987. The procedure and results of the experiments are illustrated in this paper.

Jan 1, 1990

By J. M. Stuve

Provisional values for the heat of formation of europium trichloride and europium sesquioxide were determined by solution calorimetry utilizing europium metal of more than 99-percent purity. The resulting values for the heats of formation of Eu203 (cubic) and EuCls (hexagonal) were -386,970 ±l,200 cal/mole and -218,740 ±650 cal/mole, respectively, measured at 298.15° K.

Jan 1, 1965

By C. F. Jackson

This paper has been prepared as a progress report in connection with the series of articles on mining methods and costs which are being published by the U. S. Bureau of Mines in the form of information circulars. When enough circulars have boon completed it is planned to publish a more complete and comprehensive paper in bulletin form dealing with the subject of underground transportation. Progress reports, followed b., bulletins, will be prepared from time to time dealing with other subjects included in the general study of mining methods at individual nines, such as mine development, drilling, and blasting; stoping methods (each principal stoping method to be summarized in a separate paper); Ventilation; wage, contract and bonus systems, etc.

Jan 1, 1931

By L. R. Gremillion, G. H. McClellan

Chemical and mineralogical data on 25 apatitic phosphate ores of diverse origins from commerical deposits around the world were widely variable. From 14 to 18 chemical constituents of each sample were determined, and each sample contained four to ten mineral phases. Altogether there were 34 different mineral phases, many of which occurred in only one sample. Samples contained varieties of francolites, fluorapatites, and mixed hydroxyfluorapatites. The apatite compositions calculated from chemical data showed that certain types of substitutions were characteristic of different apatite varieties, but every variety had some degree of substitution of (CO3)2- for (PO4)3-, and the P205 contents of the apatites ranged from 35.1 %for a North Carolina apatite to 41.9% for a Missouri apatite. In a concentrate with a grade of 32% P2O5, the North Carolina sample should contain about 8.7% gangue and the Missouri sample about 23.7% gangue. To optimize the digestion process of a phosphate ore, it is necessary to consider the dissolution behaviors of different mineral phases during acidulation and their possible effects on chemical properties of a fertilizer intermediate. In the production of wet-process acids or superphosphates, acidulation of certain minerals may cause foaming and formation of sludge, filtration, corrosion, and handling problems.

Jan 1, 1982

By Ralph M. Foecking

The disposal of the phosphate slimes produced by Florida beneficiation operations is perhaps the biggest single problem of the phosphate mining industry. This is an old problem which has not been solved and which is becoming increasingly severe. In a typical phosphate mining operation, the phosphate rock mined is initmately mixed with sand and clay, constituting what is known as matrix. During the beneficiation, the clay and other fine materials are separated usually at -150 mesh, and washed from the phosphate rock in a form of diluted slurry known as phosphate slimes. The quantity of slimes solids and their composition vary considerably with the location but usually represent from 25 to 35% of the ore mined. Because of the affinity that clays have for water, large volumes of water are required to separate the granular material in the matrix forming a dilute slime suspension (1.5 to 3% solids) of colloidal material, which settles very slowly, and thus requires immense impounding areas, which never becomes totally usable land. These ponds also contain about 25 to 35% of the total P205 values mined. The magnitude of the problem represented by the slimes can be appreciated better if we realize that there are around

Jan 1, 1971

By I. H. Gundiler

Although cyanidation has been universally applied in the processing of gold and silver ores, the search for less toxic alternatives continues. Difficulties encountered in processing ores containing oxidized copper minerals and the inherently slow kinetics of cyanidation have generated a renewed interest in thiosulfate leaching. This process, as well as the catalytic effects of copper ion, were well recognized and widely applied towards the end of the past century. In this study, the effects of copper, ammonia, and thiosulfate concentrations on gold dissolution were investigated using the rotating disk technique. Extraction of gold and silver from an oxidized copper-bearing ore was also studied utilizing a statistical experimental design, and these results were displayed in the form of contour plots.

Jan 1, 1993

On Feb. 16, 2012, the Polish coal mining company Lubelski Wegiel Bogdanka S.A. set the world record for daily production from a plow-equipped longwall, with an output of 24.4 kt (26,900 st) of coal from a single face. The company commissioned the first Cat longwall system at its Bogdanka Mine, near Lublin in eastern Poland, in March 2010 and within six months had raised the bar to nearly 17 kt/d (18,700 stpd) of cut coal. Since then, Bogdanka has continued to increase its daily output with a plow face that began mining in the new 7/VII/385 panel last October, taking the world record to new levels. In addition to the record output achievement, the plow face advanced more than 27 m (89 ft) at a 1.63-m- (5.3-ft-) cutting height. ?We thought this achievement would be impossible for any shearer in seam heights as low as this,? said Zbigniew Stopa, vice president of Bogdanka.

Jan 1, 2012

By P. U. W. Appel

Despite the very large offshore Exclusive Economic Zone (EEZ) area of Greenland (in excess of 2 mill. km2) virtually no work has been carried out on marine minerals on the ocean floor. Apart from a single reconnaissance survey by a mining company, major activities have been those of oil companies exploring the West Greenland shelf in the early seventies. The West Greenland shelf and its extensions is the most obvious area for year-around accessability when looking for marine mineral deposits. So far, only one onshore placer deposit has been found - ilmenite deposit near Thule, NW Greenland, whereas a gold placer in South Greenland presently is being evaluated.

Jan 1, 1988

Discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.72-90, included written contributions on size and gauge standardisation by Lupton A., Peck W.R., Dean S., Mayer R.W. and Ashworth J., with the author's written response, and by Bulman H.F. and Brown M.

Dec 1, 1916

By William R. Henkle

High-calcium limestone has been intermittently produced from the Monarch quarry since the late 1800s. Initial production was used in sugar processing and for a smelter located near Salida, Colorado. During the 1920s, Colorado Fuel and Iron Company (CF&I) began to exploit the deposit as a source of flux stone for its blast furnace steel operations at Pueblo. The deposit was operated for many years as a captive quarry by CF&I. In 1984, CF&I closed the quarrying operations at Monarch; flux stone was no longer required since the blast furnaces were taken off line in 198 1. In 1994, Colorado Lime Company, a subsidiary of United States Lime and Minerals, Inc. acquired the property. Limestone was mined from the Castle Butte Member of the Leadville Limestone (Lower Missippian). Some high- magnesium dolomite was also mined during WWII from the Redcliff Dolomite Member which directly underlies the Castle Butte. Past production was from both an upper and lower quarry at elevations ranging from 10,000 to 11,000 feet (3,048 m-3,353 m) mean sea level (m.s.1.). The reserves at Monarch quarry are in a dip slope deposit, occupying the northwest slope of Monarch Hill. The structural geology of the deposit is complex on both a region- al and mine scale. The reserves are located on the eastern limb of the Syncline Hill syncline. The beds on this limb of the structure strike to the northeast and dip to the northwest from 30 to 45 degrees. A major reverse fault separates the reserves into an upper and lower deposit. Numerous smaller normal and reverse faults cut the deposit, requiring a flexible mine plan. At the Monarch quarry, the Castle Butte Member con- sists of two stratigraphic units. The Upper unit (Mlu) is a thick-bedded, fine-grained crystalline dolomitic limestone from 0 to 300 feet (0-90 m) thick. The unit generally has an Si02 content of less than 4 percent. A bedded chert horizon and a karst horizon at the base of the unit locally raise the Si02 content as high as 20 percent. The underlying Quarry Stone unit (Mlq) is a light-gray, massive, bedded, calcilutite/micrite limestone from 90 to 130 feet (27-40 m) thick. The Quarry Stone unit is remarkably uniform chemically throughout it's entire thickness. Average analysis is CaC03 - 95 percent, MgC03 - 3.5 percent, and Si02 - 0.5 percent. The Footwall dolomite unit (Mld) of the Redcliff Member of the Leadville Limestone is a dark gray to black, blocky, medium-to-thick-bedded, calcilutite/micrite dolomite from 150 to 180 feet thick (46-55 m). The upper 100 feet (30 m) of the unit is a low-silica facies with an average Si02 content of less than 0.5 percent. MgC03 content is con- sistent at 39.8 percent throughout the upper 50 feet (15 m) of the unit but varies from 15 percent to 39.8 percent in the lower portion (50 to 100 feet [15-30 m]) of the low-silica facies. The lowest portion of the unit, 100 feet (30 m) to base of unit is high in silica and is not considered chemical grade. Current in-place, surface-minable reserves at the quarry are estimated to be 14 million short tons (st) (13 million metric tons [mt]) of limestone and 50 million st (45 million mt) of dolomite. A 1.4 million st (1.3 million mt) stockpile of finely crushed limestone is also present on the property. Colorado Lime is presently processing approximately 2,000 st (1,800 mt) per month from the crushed limestone stockpile. This material is pulverized and sold to underground coal mines for use as rock dust, some of this product is also used for environmental purposes. Limestone mining is scheduled to resume in spring of 2000.

Jan 1, 2001

By Jorgensen D. K.

The Bullfrog and Montgomery-Shoshone deposits, outside Beatty, Nevada, have a combined drill-indicated reserve of 17.4 M tons of ore with an average grade of 0.103 oz/t Au and 0.240 oz/t Ag. The deposits occur in Miocene volcanic rocks which underwent large-scale movement within a detachment-faulted terrane. The principal host to gold mineralization is a strongly welded rhyolitic tuff which experienced brittle deformation during plate movement. Open-space fractures and breccia were filled with quartz, calcite, and adularia accompanied by lesser pyrite, gold, and acanthite. Gold occurs as micron-sized particles within and adjacent to the low-angle fault and along associated listric-normal and tear faults.

Jan 1, 1989

By S. Gajardo, E. Valdés Guerra

Together with Sociedad Punta del Cobre S.A. (Pucobre) and Orica, we are carrying out a study of alternatives for methodology of excavation in Slot Up Raises from actually built with Blind Hole (BH) to drilling and blasting (DB) methodology. The study is part of the permanent search for innovation, the use of technology and the reduction of mine operation costs. This application aims to optimize the Sub Level Stoping method, which has historically been exploited at Pucobre. Using a new variant of the method “Open Stoping”, through the initial development of ascending blind raises using a pilot drilling of a bore hole, with the objective of eliminating the upper level in order to excavate the free face opening. This industrial test aims to replace the mechanized BH Up Raise of 1.5m (4.9 ft.) in diameter and 30m (98.4 ft.) high, with a Up Slot Raise considering two separate blasting events, using different technological enablers, as detailed below: accuracy drilling with relief holes of 254mm (10 in.) diameter, high viscosity bulk emulsion, wireless initiation system and high-strength injectable bulk resin. Considering the importance of the success of this application, a DB diagram was defined to allow the opening of the up raise in two blasting events, separated by intermediate stemming deck located at the same level at a height of 15m (49.2 ft.) from the collar, using high-strength injectable resin. The first blasting event considers the first section from the collar to the first 15m (49.2 ft.), using wired electronic initiation that is detonated on the first day. A second event blasts the section from 16.5 to 30m (54.1 to 98.4 ft.), using a wireless initiation system, as, it has no physical connection, is blasted on the second day after the extraction of the material resulting from the first event. For greater precision, the design of the explosive charge configuration and initiation sequence is made, adjusted to the measurements of trajectory deviations of the actual ground drilling and is also considered for the control of the explosive charge configuration with high viscosity bulk emulsion. This application improves the profitability of the mining business by generating savings through the change of Blind Hole methodology, estimating a savings of more than 75% per Up Slot Raise

Jan 1, 2024

By E. W. Dewing

The solubility of A14C3 in cryolite melts has been determined by holding the melt with aluminum in a graphite crucible for 4 hr at temperature, quenching the crucible in water, and analyzing the frozen salt by CH4 evolution. The solubility is given by log(wt % Al4C3) = 1.298 -1.l74 (wt ratio NaF/AlF3) independent of temperature in the range 985" to 1080°C. Additions ofA1203, .NaCl, CaF2, or LiF up to 10 wt pct do not affect the solubility, provided that LiF and CaF2 are replaced by equivalent NaFin calculating the ratio. The variation with ratio can be accounted for quantitatively on the hypothesis that the Mechanism of solution is Al4C3 + 2AIF3 = 3Al2CF2 since the solubility varies as (aAIF3) 2/3; Mechanisms involving C", C2- , AlC- , A12C2+, and Al2CF+are re-jected. At ratios above 1.5 truces of c;- are also present. It was noticed some years ago in this laboratory that carbon specimens made cathodic in a cryolite bath decrease in diameter over a period of time.' It was also found that cryolite which had been melted with aluminum in a graphite crucible was sometimes yellow, and that A14C3 could be seen intimately embedded in the cryolite crystals. CH, could be recovered by acid attack. There was thus reason to believe that A14C3 had a genuine solubility in molten cryolite, and the object of this work was to measure it. EXPERIMENTAL AND RESULTS A graphite crucible, 2 in. ID and 2.5 in. deep with a close-fitting lid, contained about 150 g of cryolite (plus additives) and about 20 g of 99.99 pct pure Al. It was placed in a vertical Inconel furnace tube, covered with refractory brick to provide thermal insulation, and the top of the tube was roughly sealed with disks of asbestos paper. An alumina tube led argon down to the level of the top of the crucible to expel air, and an alumina sheath with a Pt-10 pct Rh ther-mocouple inside was positioned between the crucible and the wall of the Inconel tube. The tube was heated in an electrical resistance furnace for the desired length of time; the refractory bricks were then removed, and the crucible was lifted out with tongs and quenched in water. After such a crucible was broken open it could be seen that its inner surface was yellow owing to the presence of A1,C3, and sometimes needle-like crystals could be observed (at X75 magnification) growing out into the nielt. It was concluded that Al,C, had been present as a separate phase when the crucible was at tenlperature and that the melt had been saturated: in

Jan 1, 1970

By Herbert H. Einstein

The thrust of research reported in Part I was to collect in-situ data from exploration programs and the published literature, and to empirically establish distributional patterns for these variables. Since discontinui¬ties in a rock mass govern to a large extent its engineering properties and thus the performance of any slope in the mass, work has been devoted to determining the appropriate distributional forms for attitude spacing and length of discontinuities and to distributional properties of resis¬tance and deformability parameters. The conclusion from these analyses is that trace lengths are logNormally distributed and that joint spacing is Exponentially distributed, regardless of orientation of the sampling line, and regardless of whether each joint set is considered separately or not. Joint orientation (attitude) data representing 22 individual joint sets from eight sites (a total or approximately 20,000 joints), do nor strongly support any of the commonly used distributions as broadly applicable in practice. The autocorrelation )f geometric joint properties is also examined. However, no significant spatial correlation could be found even after extensive data manipulation. The investigation of resistance and deformability parameters starts with a review of mechanisms and models that are used to represent them. Review and statistical evaluation of approxi¬mately 2,000 discontinuity shear tests has shown that good statistical estimates for use in reliability analyses can be obtained for friction angles.

Jan 1, 1979

In the death of Major A. B. desaulles at South Bethlehem, Pa., on Dec. 24, 1917, the Institute lost a valued and esteemed member, one of the last few of those who, in May, 1871, at Wilkes-Barre, attended the first meeting of the Institute, in response to a call that had been issued by R. P. Rothwell, Eckley B. Coxe, and Martin Coryell. Major desaulles was born Jan. 8, 1840, at New Orleans, and was the son of Louis and Armidc Longer desaulles, each of French descent. As a boy he was privately tutored in the South, and then schooled in New England to enter the Rensselaer Polytechnic Institute, where he was graduated with honors in the class of '59. Following his graduation he studied in France and Germany for two years, returning to New Orleans in 1861 to enter the Confederate Army, in which he served with distinction as an engineer throughout the Civil War, rising to the rank of Major and the command of his Corps. After the close of the war he pursued his studies abroad for another year, returning to New York in April, 1866, when he became engineer for the New York & Schuylkill Coal Company, and remained at its plant near Wilkes-Barre until October, 1871, when it was sold to the Philadelphia & Reading Coal and Iron Company. He then returned to New York where for several years he was engaged in the practice of his profession. In 1869, he married Catharine M. Heckscher, daughter of Charles Heckscher of New York City. Mrs. desaulles survives him. In 1876, Major desaulles became superintendent of the Dunbar Furnace Company in Fayette County, Pa., with which company he remained until 1883. As a feature of the Pittsburgh meeting in May, 1879, Major and Mrs. desaulles entertained the members of the Institute at dinner at Dunbar on the occasion of the Institute's visit to Dun-bar furnace. In 1883, he took up the formation of the Oliphant Furnace Company in that county, of which he became and remained the head for five years. He was then called to the superintendency of the New Jersey Zinc Company at South Bethlehem, Pa., in which position he remained until his retirement,from active service in 1911, maintaining, however, hi.; keen interest in the metallurgy and smelting of zinc, in collaboration with his son Charles, a member of the Institute and a Director of the American Smelting and Refining Company. From 1888, until his death, he resided in South Bethlehem, a prominent and highly respected citizen of that progressive and stirring community. Major desaulles was a member of the Protestant Espicopal Church, and at the time of his death was a vestryman of the Church of the Nativity at South Bethlehem. He was president of the Men's Club of the Church of the Nativity. His kindly nature led him to take an active interest in the promotion of healthful sports among young men. He was ever active in all things pertaining to the general welfare and uplift of his fellowmen. In his death the profession has lost a distinguished engineer and mctallurgist and our country a patriotic able citi-zen and man of affairs—one greatly beloved by those whom he honored with his friendship, and respected and looked up to by all who were privileged to know him.

Jan 1, 1920

By W. A. Selvig

EQUIREMENTS of montan wax for industrial use in the United States before World War II were met by imports, nearly all of which came from Germany. An important industry for extraction and refinement of this wax from certain brown coals had developed in Germany. At the beginning of the war, montan-wax imports were shut oft, and American industry was forced to rely largely on substitutes. Since the war, relatively small amounts have been imported from Czechoslovakia. Because of the shortage of montan wax at the close of the war and the fact that industry in the United States had to rely on foreign sources in the past, this investigation was started in 1945 to determine probable yields of wax from domestic lignite. Results of the investigation and the properties of extracted waxes are described in this report. Also included in the report are discussions of the occurrence and geology of lignite deposits of the United States from which samples were obtained for wax extraction and the petrographic composition of lignites, particularly in respect to those components that contribute to wax yields.

Jan 1, 1950

By R. E. Reed-Hill, J. L. Martin

Kinking is an important deformation phenomenon in poly crystalline a zirconium. The crjlstallo-gvaphic features of the most important form of kinking have been determined with the aid of twins formed at 77°K in grains previously kinked at high temperatures. It has been .found that the kink-band boundaries correspond to walls of edge dislocations with (1150) Burgers vectors and dislocation lines parallel to (1070). The present observations imply that basal slip is an important secondary-slip mode in polycrystalline zirconium. Previous single-crystal studies13 did not veveal this mode Other evidelzc.e for (0002)(1120) slip is also presented. ThE first studies of kinking in hexagonal metals were made by orowan,1 using single-crystal cadmium wires. He suggested that this was a new de- formation mode in metals, different from ordinary glide or twinning. Next, Hess and Barrett2 studied zinc-crystal rods in compression, and were able to offer an explanation of the phenomenon described by Orowan. They concluded that kinks required no new deformation mechanism and were a special form of deformation band that developed gradually and solely from basal glide. Similar kink bands were then observed by Washburn and parker3 on zinc crystals deformed in tension at low stresses and high temperatures. In titaniun,4 kink bands associated with {1010}<1120> prism slip have been observed in coarse-grained specimens. Magnesium5 and rhenium6 have also been observed to kink in conjunction with their basal- and {1010} prism-slip systems, respectively. Yttrium has (1010) as a predominant slip plane, but no observations of kink bands were reported.7 Since no previous investigations of kink bands in zirconium have apparently been made, this study was proposed. Its aim was to determine the crys-tallographic features of a type of kink band frequently observed in polycrystalline zirconium. EXPERIMENTAL APPARATUS All tests were performed on a type TTC Instron machine. The cross-head speed usually chosen in tension or compression was 0.02 in. per min. Ten-

Jan 1, 1964

By Werner Engelmaier

Constant-strain rotating-bending fatigue tests were conducted on 2024-T3 aluminum alloy constant-strain McAdams-type specimens in ultrahigh vacuum, 10-lo Torr, and in atmospheric air. In the elastic strain range the ratio of vacuum-to-air fatigue life varied from about 10 at a maximum bending stress of 37 ksi to near unity at the endurance limit. After 10 pct of the fatigue life, intergvanular microcracks appeared on the surface which did not appreciably propagate further until the last 5 pct of the fatigue life, where trans-granular cracks propagating first in slip-plane cracking and then in the stress-dominated mode led to failure. No reduction in residual tensile strength resulted from the fatigue of the specimens short of fracture. The mechanism governing the fatigue life operates between the occurrence of the intergranular microcracks and the initiation of the trans granular cracks. MORE than forty years ago, Mc Adam&apos; and Haigh2 published the first systematic studies showing that the fatigue properties of metals were greatly affected by environments. Gough and sopwith3 found in a later study that the fatigue life of metals subject to corrosion can be substantially increased by reducing the atmospheric pressure. This and their later work4&apos;5 was, however, done in a vacuum of only 10~3 Torr. Subsequent studies6-&apos; at a vacuum of 10- Torr showed that water vapor is the primary agent affecting the fatigue properties of aluminum alloys. Only recently was ultrahigh vacuum used for fatigue studied.l Various theories have been put forward to explain this phenomenon. Wadsworth and Hutchings12 postulated that cracks form very early in the test and that the chemical attack by the corrosive components of the atmosphere at the root of the cracks enhances the speed of the crack propagation. They also noted that chemisorbed layers of gas on the fresh crack surfaces prevent cold welding of the crack and make the separation irreversible. Ham and Reichenbach, on the other hand, reported that their specimens showed no cracks after a run in vacuum, even though the runs were long enough to have caused the specimen to fracture in atmospheric air. They also reported that in argon at 0.14 Torr the fatigue life was about 5 times longer than at 7 X lo-&apos; Torr. Jacisinll reported that fatigue tests in dry nitrogen showed results close to those obtained in ultrahigh vacuum. The present experiment was designed to determine the extent to which cumulative fatigue damage, i.e., the accumulation of length of fatigue cracks, reduces the residual static tensile strength of an aluminum alloy in both ultrahigh vacuum and atmospheric air and to obtain fatigue-life data for this aluminum alloy at various strains. It was also hoped that information ex- tracted from these data might support one of the previously mentioned theories. 1) EXPERIMENT Test Specimens. The material tested was commer-cial 2024-T3 aluminum alloy. In addition to aluminum, this alloy contains approximately 4.4 pct Cu, 0.5 pct Fe, 0.5 pct Si, 0.6 pct Mn, 1.5 pct Mg, plus smaller amounts of other elements.13 Some typical mechanical properties of this aluminum alloy are listed in Table I.&apos;~ The material was used in the as-received condition, i.e., solution-treated and cold-worked. Mc Adam-type1&apos; constant-stress specimens and notched fatigue specimens were machined from 4 -in. -diam rods, Fig. 1. The critical section of the McAdam-type samples was polished with a 45-deg spiral motion to a No. 8 microfinish. The notch in the notched specimens was machined on a lathe with a forming

Jan 1, 1969

By Yuhua Wang, Haitao Zheng, Guangli Zhu, Yuehao Zhao, Fushun Yu, Dongfang Lu

"Spodumene, feldspar and quartz possess similar surface properties, which make the difficult to separate spodumene from other silicate minerals by flotation. The differences of crystal structure, surface property and floatability of three minerals were studied by various technical means. The results show that Li-O and Al-O bonds in spodumene structure are not strong and easy to be broken. However, Al-O and Si-O bonds in feldspar and Si-O bond in quartz are very strong and not easy to be broken. High contents of Al and Li on spodumene surface were found by XPS measurements, which is benefit for the adsorption of anionic collector. The surface energies of main cleavage planes of spodumene (110), feldspar (001) and quartz (001) are 1.88 J/m2, 2.97J/m2 and 2.68J/m2, respectively. Hence, the exposed surfaces of feldspar and quartz are not saturated and easy to adsorb OH- ions from solution and cause the lower IEP than spodumene. The contact angles of three minerals in water are lower than 16º, suggesting that the hydrophilicity of three minerals is high, and the order of hydrophilicity is quartz > feldspar >spodumene. Correspondingly, contact angles and flotation recoveries of spodumene are bigger than that of feldspar and quartz in presence of a combined anionic and cationic collector named YOA.INTRODUCTION Flotation technology plays most important role for the recovery of spodumene from pegmatite ore. Generally, spodumene with fresh surface is easy to be floated using soap and oleic acid as collector, and the best flotation pH range is 4.0 to 9.0. However, the flotability of spodumene will become worse when its surface was polluted by slime which produced by the weathering of spodumene and other silicates (Dresler et al. 1998; Moon and Fuerstenau 2003; Menéndez et al. 2004; Yu et al. 2015). In addition, the species of Ca2+, Fe3+, Mg2+ and other metal ions in pulp can not only activate the flotation of spodumene, but also the activation of gangue minerals, and then the flotation selectivity of spodumene from gangue minerals became wores (Wang and Yu 2007; Yu et al. 2014). In order to eliminate the negative effects of slime and metal ions on the flotation of spoddumene, the desliming and long time scrubbing with the addition of NaOH and Na2CO3 were adopted. Usually, NaOH shows the activation for spodumene flotation, and the recovery of spodumene increases with the increase of NaOH dosage. Na2CO3 can eliminate the non selective activation of Ca2+, Fe3+, Mg2+ ions in the pulp, and the concentrate grade of spodumene increases with the increase of Na2CO3 dosage. Anionic collectors such as chelants, hydroxamic acid, oxidized paraffin soap, naphthenic acid and oleic acid were widely used for the flotation of spodumene (Dresler et al. 1998; Moon and Fuerstenau 2003; Menéndez et al. 2004; Yu et al. 2015)."

Jan 1, 2018